Q235GJE building steel plate bundles stacked outdoors at SHH STEEL steel yard

GB/T 19879 Q235GJE Building Steel Plate Supplier

GB/T 19879 Q235GJE is high-performance building structure steel plate with 235 MPa minimum yield, a 235 – 345 MPa yield window, yield ratio ≤0.80 and 47 J Charpy impact at −40°C. SHH STEEL supplies Q235GJE mill-direct, 6 mm – 150 mm, with Z15, Z25 or Z35 options and full heat and product analysis.
Keywords
Q235GJE, Q235GJE steel plate, GB/T 19879 Q235GJE, Q235GJ-E, Q235GJEZ15, Q235GJEZ25, Q235GJEZ35, Q235GJ, building structure steel plate, Q235GJE supplier
Equivalent Grades
GB/T 19879 Q235GJE / EN 10025-2 S235J2 (−20°C, strength only) / JIS G3136 SN400C (closest building steel, 0°C) / JIS G3106 SM400C / ASTM A36 (strength only) / EN 10025-3 S275NL (−50°C) — Material Specification: GB/T 19879-2023 (supersedes GB/T 19879-2015) — Delivery: AR, CR, NR or N; −40°C impact
Share:
General Description
Material Specification
Chemical Composition
Mechanical Properties
Q235GJE vs Q235D
Q235GJ or Q355GJ?
Material Comparison
Z15 / Z25 / Z35
Equivalent Material Grades
Weldability
Heat Treatment and Delivery Condition
Dimensions
Tolerances
Supplementary Requirements
Price and Ordering
Applications
Supply Capability
Why Choose SHH STEEL
FAQ
Conclusion

What is GB/T 19879 Q235GJE Building Steel Plate?

Q235GJE, also written Q235GJ-E or Q235 GJE, is hot-rolled steel plate for building structures under GB/T 19879. Q means yield, 235 is the minimum yield in MPa, GJ (gao jian) marks high-performance building steel, and E is the quality grade: Charpy V-notch at −40°C, at least 47 J.

The GJ rules are what the structural engineer is paying for. Q235GJE sets a maximum yield as well as a minimum, caps the yield ratio, limits carbon equivalent by thickness and delivery route, and keeps P and S low. The frame then yields where the designer expects.

Q235GJE fills a real gap. GB/T 700 Q235 stops at grade D, so for a 235 MPa member that must pass Charpy at −40°C, Q235GJE is the Chinese answer. Mills roll it to order, not to stock, and controlled rolling or normalizing is the usual route to a reliable 47 J at −40°C.

GB/T 19879-2023 replaced GB/T 19879-2015 on 1 April 2024. For Q235GJ the chemistry, CEV, 0.80 yield ratio and 47 J carry over unchanged. The 2015 edition used lower yield ReL and stepped yield down 10 MPa above 50 mm (235–345 MPa for >16–50 mm, 225–335 MPa for >50–100 mm). The 2023 edition uses upper yield ReH and holds 235–345 MPa all the way to 100 mm. Delivery codes WAR/WCR became AR/CR, and NR was added. Sister grades are listed under GB/T 19879, including Q235GJB.

SHH STEEL (Shanghai Shenghonghe Import & Export Co., Ltd.) is a steel manufacturer and exporter and global steel mill sourcing partner, mill-direct, China origin. We ship Q235GJE cut to size with an EN 10204 3.1 or 3.2 certificate.

Material Specification

Specification element Requirement SHH STEEL compliance
Plate standard GB/T 19879-2023 Q235GJE (GB/T 19879-2015 when the drawing names it) Confirmed
Thickness for Q235GJ 6 mm – 150 mm Confirmed
Yield strength 235 MPa min; 235 – 345 MPa for 16–100 mm Confirmed
Tensile strength 400 – 510 MPa (to 100 mm) Confirmed
Yield ratio ≤ 0.80 Printed on MTC
Quality grade E, Charpy V at −40°C, KV2 ≥ 47 J, longitudinal Confirmed
Delivery condition AR, CR, NR or N As ordered
Through-thickness Z15, Z25 or Z35 to GB/T 5313 As ordered
Dimensions GB/T 709-2019, thickness tolerance Class B Confirmed
Chemistry report Heat analysis + CEV; product analysis on request Confirmed
Certificate EN 10204 3.1 or 3.2 As ordered

Grades often confused with it are EN 10025-2 S235J2, ASTM A283 Grade C and ASTM A36. None of them carries the GJ yield cap or yield-ratio rule.

Chemical Composition: Heat Analysis and Product Analysis

Read the chemistry of Q235GJE in two layers. Layer one is the heat (ladle) analysis on the certificate, judged against Table 1. Layer two is product analysis on the finished plate, judged against Table 1 plus the GB/T 222 deviations (clause 7.1.4). Mixing the two causes most chemistry disputes we see.

Table 1 below is the heat analysis for Q235GJE. The columns on the right show the quality-grade groups at Q235GJ.

Table 1. Heat (ladle) analysis, GB/T 19879-2023 Table 1, %

Element Q235GJE heat analysis (%) Q235GJ B / C Q235GJ D / E
C, max 0.18 0.20 0.18
Si, max 0.35 0.35 0.35
Mn 0.60 – 1.50 0.60 – 1.50 0.60 – 1.50
P, max 0.020 0.025 0.020
S, max 0.010 0.015 0.010
Als, min 0.015 0.015 0.015
Cr, max 0.30 0.30 0.30
Cu, max 0.30 0.30 0.30
Ni, max 0.30 0.30 0.30
Mo, max 0.08 0.08 0.08
V + Nb + Ti, max (if combined) 0.15 0.15 0.15

Notes to Table 1. Total aluminium (Alt ≥ 0.020%) may replace acid-soluble aluminium. If Al, V, Nb or Ti is added alone or together at 0.015% or more, the minimum aluminium does not apply. V + Nb + Ti, when combined, is limited to 0.15%. These limits are the same in the 2015 and 2023 editions.

B and C grades share one chemistry column. D and E grades tighten carbon to 0.18%, phosphorus to 0.020% and sulfur to 0.010%, because they are tested at −20°C and −40°C.

Table 2. Product analysis limits for Q235GJE, GB/T 19879 clause 7.1.4 with GB/T 222-2025, %

Element Heat limit (%) Permitted deviation, GB/T 222-2025 Table 1 Q235GJE product analysis limit (%)
C ≤ 0.18 +0.02 ≤ 0.20
Si ≤ 0.35 +0.03 ≤ 0.38
Mn 0.60 – 1.50 ±0.06 0.54 – 1.56
P ≤ 0.020 +0.005 ≤ 0.025
S ≤ 0.010 +0.005 ≤ 0.015
Als ≥ 0.015 −0.003 ≥ 0.012
Cr ≤ 0.30 +0.05 ≤ 0.35
Cu ≤ 0.30 +0.05 ≤ 0.35
Ni ≤ 0.30 +0.05 ≤ 0.35
Mo ≤ 0.08 Not listed in Table 1 Agree in contract
V, Ti (each, if added) — +0.02 / −0.01 Heat value + 0.02
Nb (if added) — ±0.005 Heat value ± 0.005

How to read Table 2. The deviation band is picked by the upper limit in Table 1. For Mn the upper limit is 1.50%, inside the 0.80–1.70% band, so ±0.06% applies to both ends.

GB/T 222-2025 replaced GB/T 222-2006 on 1 December 2025. One more rule from it matters to buyers: if no reliable heat analysis exists, the product analysis must meet the heat limits with no deviation at all (clause 5.6).

Z-grade plate is cleaner still. GB/T 5313-2023 limits sulfur by heat analysis:

Z grade Heat sulfur, max (%) Reduction of area, avg / single (%)
Z15 0.010 15 / 10
Z25 0.007 25 / 15
Z35 0.005 35 / 25

CEV and Pcm are always worked out from the heat analysis, not the product analysis. SHH STEEL prints the heat values used and adds a product-analysis column on request. This is building steel, not boiler chemistry such as GB/T 713 Q345R in GB/T 713.

Mechanical Properties

Values below follow Table 3 and Table 5 of GB/T 19879-2023 for Q235GJ. Tensile specimens are transverse; Charpy specimens are longitudinal.

Thickness Upper yield ReH (MPa) Tensile Rm (MPa) Yield ratio, max Elongation A, min
6 – 16 mm ≥ 235 400 – 510 0.80 23%
> 16 – 100 mm 235 – 345 400 – 510 0.80 23%
> 100 – 150 mm 215 – 325 380 – 510 0.80 23%

The 2015 edition used lower yield ReL and stepped yield down 10 MPa above 50 mm. Write the edition on the order so the mill tests to the right table.

Test Q235GJE requirement
Charpy V-notch, longitudinal −40°C, KV2 ≥ 47 J, average of 3
Single value One value may fall below the average requirement, not below 70% of it (GB/T 17505)
Sub-size specimens 7.5 mm or 5 mm wide when plate is too thin: 75% or 50% of the required energy
180° bend Per Table 6 to GB/T 232; may be omitted when the mill guarantees it (7.4.3.2)
Through-thickness (≥ 15 mm) Z15, Z25 or Z35 to GB/T 5313, when ordered

Density for theoretical weight is 7.85 g/cm³.

Q235GJE vs Q235D: Why There Is No Q235E

Q235D is the coldest letter in GB/T 700. It is common, cheap and tested at −20°C with 27 J. On paper it looks close to Q235GJE. It is not.

The difference is control. Q235D has no yield ceiling and no yield-ratio rule, and its yield falls with thickness. GJ plate keeps a 110 MPa yield window, a 0.80 ratio cap and a CEV limit printed on the certificate.

Property Q235D (GB/T 700) S235J2 Q235GJE (GB/T 19879)
Yield, minimum 235 MPa to 16 mm; 225 MPa to 40 mm; 215 MPa to 100 mm 235 MPa to 16 mm, then steps down 235 MPa to 100 mm
Yield upper limit None None 345 MPa above 16 mm
Yield ratio limit None None ≤ 0.80
C, max 0.17% 0.17–0.20% by thickness 0.18%
P / S, max 0.035 / 0.035% 0.025 / 0.025% 0.020 / 0.010%
Impact −20°C, 27 J −20°C, 27 J −40°C, 47 J
CEV limit None 0.35–0.40% by thickness 0.34% to 50 mm
Z15–Z35 By agreement EN 10164 option GB/T 5313 option

GB/T 700 has grades A, B, C and D. There is no Q235E. For a 235 MPa member tested at −40°C, a buyer in China has two choices: Q235GJE, or step up to a 355 MPa grade such as GB/T 1591 Q355NE.

European drawings that need −40°C or colder at this strength usually call EN 10025-3 S275NL or EN 10025-4 S275ML, tested at −50°C. Those are 275 MPa grades without the GJ yield cap.

Q235GJE or Q355GJE: When Is 235 MPa the Right Choice in a Cold Climate?

Check Q235GJE Q355GJE
Yield, 16–100 mm 235 – 345 MPa 355 – 475 MPa
Tensile 400 – 510 MPa 490 – 610 MPa
Yield ratio ≤ 0.80 ≤ 0.83
CEV ≤ 50 mm 0.34% 0.43% (AR/N), 0.38% (TMCP)
Impact −40°C, 47 J −40°C, 47 J
Max thickness 150 mm 200 mm

Both grades carry the same quality letter and the same 47 J. The choice is about load and welding. Q235GJE has the lowest CEV in the standard, 0.34% to 50 mm, so it welds in cold weather with little or no preheat on thin plate.

If the member is strength-governed, Q355GJE usually wins on weight. Where stiffness, deflection or minimum thickness governs, 235 MPa steel does the job for less money. Our 355 MPa building plate pages use the older name: Q345GJE.

Q235GJB, Q235GJC, Q235GJD or Q235GJE: Which Quality Grade?

Grade Impact temperature Energy, min C / P / S max (%) Typical use
Q235GJB +20°C 47 J 0.20 / 0.025 / 0.015 Heated interiors, mild climates
Q235GJC 0°C 47 J 0.20 / 0.025 / 0.015 Cold regions, exposed frames
Q235GJD −20°C 47 J 0.18 / 0.020 / 0.010 Severe winters, thick welded nodes
Q235GJE −40°C 47 J 0.18 / 0.020 / 0.010 Arctic and low-temperature sites

Strength, yield ratio and CEV do not change from B to E. Only the impact temperature and the D/E chemistry move. Over-specifying the letter costs money; under-specifying it costs safety. Use the design temperature.

Q235GJE is the coldest letter in GB/T 19879; there is no F grade in this standard. For the same letter at another strength level: one level up, Q345GJE.

Q235GJEZ15, Q235GJEZ25 and Q235GJEZ35: Through-Thickness Plate

Through-thickness ductility matters wherever the load path runs across the plate: column flanges at moment connections, cruciform nodes, anchor base plates. GB/T 5313 measures it as reduction of area on short-transverse specimens.

The designation adds the Z level to the grade, for example Q235GJEZ25. Z tests apply to plate 15 mm and thicker and follow GB/T 5313-2023.

Z grade Heat sulfur, max (%) Reduction of area, avg / single (%)
Z15 0.010 15 / 10
Z25 0.007 25 / 15
Z35 0.005 35 / 25

The E melt already caps S at 0.010%, the Z15 limit, so Z25 and Z35 are the levels that change the steelmaking.

GB/T 19879-2023 clause 7.6 requires every Z plate to be ultrasonic tested one by one to GB/T 2970, acceptance level III. Z35 costs most: lowest sulfur, more rejects, and a Z test on each plate.

Z35 on every plate is an easy line to write and an expensive one to buy. Let the joint detail decide where it goes.

Equivalent Material Grades

No foreign grade copies every GB/T 19879 rule. JIS G3136 SN400C limits yield range and yield ratio, but its impact test is at 0°C, so it does not match the E letter.

Designation Region Standard Notes
Q235GJE China GB/T 19879 Grade on this page
SN400C Japan JIS G3136 Closest building-steel counterpart (yield range, ratio, Z); tested at 0°C
EN 10025-2 S235J2 Europe EN 10025-2 −20°C, 27 J; strength only
EN 10025-3 S275NL Europe EN 10025-3 −50°C, 27 J; 275 MPa, used when −40°C toughness is the driver
JIS G3106 SM400C Japan JIS G3106 0°C; no yield-ratio rule
DIN 17100 St37-3 Germany DIN 17100 (withdrawn) −20°C legacy grade on old drawings
ASTM A36 USA ASTM A36 ~250 MPa; no impact or ratio rule
ASTM A709 Grade 36 USA ASTM A709 Bridge grade; impact by zone

European projects normally pair EN 10025-2 plate with EN 10164 Z grades. We dual-certify to ASTM A36/A36M or JIS G3106 only when both tables pass.

Weldability

GB/T 19879 makes the mill calculate CEV from the heat analysis and print it, together with the elements used, on every Q235GJE certificate:

CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15

Pcm = C + Si/30 + Mn/20 + Cu/20 + Ni/60 + Cr/20 + Mo/15 + V/10 + 5B

Delivery condition CEV ≤ 50 mm CEV > 50 – 100 mm CEV > 100 – 150 mm Pcm ≤ 50 mm Pcm > 50 – 100 mm Pcm > 100 – 150 mm
AR, CR, NR, N 0.34 0.36 0.38 0.24 0.26 0.27

Q235GJ has the lowest CEV in the standard. Thin plate normally needs no preheat; thick column plate, high restraint or sub-zero shop temperatures follow the qualified WPS.

The E letter helps: carbon is capped at 0.18% and P and S are lower, which reduces hot-cracking and HAZ embrittlement risk.

Typical consumables: E43-class low-hydrogen electrodes (GB/T 5117) or ER49/ER50 solid wire. Shops work to GB 50661 or AWS D1.1. Write the CEV basis (actual heat, not table maximum) into the WPS.

Heat Treatment and Delivery Condition

GB/T 19879-2023 allows four delivery conditions for Q235GJE: AR (hot rolled), CR (controlled rolled), NR (normalizing rolled) or N (normalized). The condition is agreed in the contract.

For D and E grades we prefer CR or N: grain refinement is what carries 47 J down to −40°C. Plain AR plate is accepted only on thin sizes with a proven mill record.

Q235GJ is never quenched and tempered. QT plate belongs to GB/T 16270, such as GB/T 16270 Q460C. European normalized and TMCP comparisons are EN 10025-3 S275NL and EN 10025-4 S275ML.

Test lots follow clause 9.2 of GB/T 19879-2023; retests and judgement follow GB/T 17505.

Dimensions

What we roll and cut in Q235GJE:

  • Thickness: 6 mm – 150 mm; most orders 8 mm – 100 mm
  • Width: 1500 mm – 3000 mm standard; wider by mill confirmation
  • Length: 3000 mm – 12000 mm; longer by enquiry
  • Edge: mill edge or cut edge
  • Weight: theoretical, on the mean of maximum and minimum thickness, 7.85 g/cm³

Column flanges, diaphragms, stiffeners and gussets are cut to drawing. Rolled sections for the same frame are under steel beam profiles and steel structural profiles.

Tolerances

For Q235GJE, thickness tolerance follows GB/T 709-2019 Class B unless the order says otherwise: −0.30 mm on the minus side at every thickness, with the plus side shown below. Zero-minus Class C can be agreed.

Nominal thickness (mm) Width ≤ 1500 mm Width > 1500 – 2500 mm
> 8 – 15 −0.30 / +0.80 −0.30 / +1.00
> 15 – 25 −0.30 / +1.00 −0.30 / +1.20
> 25 – 40 −0.30 / +1.10 −0.30 / +1.30
> 40 – 60 −0.30 / +1.30 −0.30 / +1.50
> 60 – 100 −0.30 / +1.50 −0.30 / +1.80
> 100 – 150 −0.30 / +2.10 −0.30 / +2.50

Flatness and width follow GB/T 709. EN 10029 or ASTM A6 tolerances are possible if written on the order.

Supplementary Requirements

Q235GJE already fixes strength, yield ratio, CEV and −40°C impact. Anything more goes on the purchase order.

  • Edition: GB/T 19879-2023 or -2015. Never write only Q235.
  • Product analysis: ask for a second chemistry column checked to GB/T 222.
  • Through-thickness: add Z15, Z25 or Z35, e.g. Q235GJEZ25.
  • Delivery condition: name it (AR, CR, NR or N) if the welding procedure depends on it.
  • Ultrasonic testing beyond Z plates: GB/T 2970 class, or EN 10160 / ASTM A578.
  • Impact: extra test positions (e.g. quarter thickness) or transverse tests, if the owner wants them beyond the E letter.
  • Tolerance: Class C for zero minus.
  • Inspection: EN 10204 3.2 with SGS, BV, TÜV or a named inspector.

Q235GJE Price Factors and How to Order

When you compare Q235GJE offers, compare extras line by line. These are the items that move the price.

Cost driver Effect on price
GJ grade over general Q235 plate Grade extra for cleaner steel, yield control and CEV
Quality letter E Highest letter extra: −40°C testing, cleaner melt, more retest risk
Delivery route CR or N costs more than AR
Thickness Thin and very thick plate carry size extras; 10–60 mm is usually cheapest
Z15 / Z25 / Z35 Desulfurization, plate-by-plate Z test and UT; Z35 costs most
Width and length Over 3000 mm wide or 12 m long needs mill confirmation
Quantity per size Mill rolling minimums per size; small lots come from stock or combined rolling
Inspection and cutting 3.2 witness, profile cutting, blasting and priming are quoted per item

To get a firm quote in one round, send:

  • Grade and edition, e.g. Q235GJEZ25 to GB/T 19879-2023
  • Thickness × width × length and pieces or tonnes
  • Delivery route, UT standard and class
  • Certificate type and inspector
  • Destination port and Incoterm

We quote plate price, extras and freight line by line, so you can compare like with like. Need a different letter? See Q235GJD.

Applications

Sector Typical Q235GJE components
Light industrial halls Stiffeners, gussets, base plates, mezzanine framing
Cold-storage and freezer buildings Frames and connection plates in rooms held below 0°C
Public buildings Secondary trusses, canopy frames, stair structures
Seismic frames Brace gussets and low-demand link plates

E grade is for the coldest sites and for owners who specify −40°C for every primary member.

It is the wrong plate for pressure equipment (pressure vessel steel plates), for bare exposed steel (weathering steel plates) or for ship hulls (shipbuilding steel plates).

Supply Capability and Global Delivery

SHH STEEL sources Q235GJE from first-line building-steel mills: Wuyang (Wugang), a drafting mill of GB/T 19879, plus Xinyu, Valin Xiangtan, Shougang, Puyang and Hongchang when size requires.

  • Certificates: EN 10204 3.1 standard; 3.2 with third-party witness
  • Tests: tensile, −40°C Charpy, bend, Z test to GB/T 5313, UT to GB/T 2970, product analysis
  • Processing: CNC plasma and flame cutting, bevelling, drilling, shot blast and primer
  • Terms: FOB Shanghai, CFR, CIF; TT, LC or TT + LC
  • Marking: steel-stamped and paint-marked with grade, heat, size and mill

Our Q235GJE exports go where Chinese design codes go: high-rise, airport and industrial projects run by EPC contractors abroad. The same team ships GB, ASTM, ASME, EN, DIN and JIS plate worldwide.

Lead time: stock sizes about 5–7 days; mill rolling about 30–45 days; Z35 or 3.2 inspection adds about 1–2 weeks. Sea time from Shanghai is about 7–12 days to Singapore and 28–35 days to Rotterdam.

Why Choose SHH STEEL

SHH STEEL is mill-direct: steel manufacturer and exporter and global steel mill sourcing partner, China origin. Every Q235GJE plate we ship carries the original mill heat number.

Before shipment we check four lines on every certificate: yield inside the GJ window, yield ratio within the cap, CEV inside the thickness band for the delivery route, and −40°C impact at 47 J or more. If one fails, the plate does not ship as GJ.

We also tell buyers when they are over-specifying. If the frame needs 355 MPa, we quote Q345GJE; if it needs no GJ rules, we say so. Browse more structural steel plates and high strength low alloy plates.

FAQ

What is Q235GJE steel?
Q235GJE is high-performance building structure steel plate to GB/T 19879. It has 235 MPa minimum yield, a 235–345 MPa yield window from 16 to 100 mm, yield ratio ≤0.80, CEV limits by delivery route and Charpy impact of at least 47 J at −40°C. GJ stands for gao jian, high-performance building steel.
What is the difference between Q235GJE and Q235D?
Q235D (GB/T 700) has a 235 MPa minimum yield that falls with thickness, no yield cap, no yield-ratio limit and 27 J at −20°C. Q235GJE (GB/T 19879) holds 235 MPa to 100 mm, caps yield at 345 MPa, limits the yield ratio to 0.80 and needs 47 J at −40°C. GB/T 700 has no E grade, so Q235GJE is the 235 MPa option for −40°C.
Is Q235GJE suitable for −40°C service?
Yes. Q235GJE is Charpy tested at −40°C and must average at least 47 J on longitudinal specimens. GB/T 19879 has no colder letter, so for design temperatures below −40°C look at GB/T 1591 Q355MF and check the yield-cap rules separately.
Why choose Q235GJ instead of Q355GJ?
Choose Q235GJ when stiffness, deflection or minimum thickness governs rather than strength. It costs less, has a lower CEV (0.34% vs 0.43% to 50 mm) and the same 47 J impact letters. Where strength governs, Q355GJ usually saves weight.
How is Q235GJE priced?
Q235GJE is priced as a base plate price plus extras: GJ grade extra, E-letter impact extra, thickness and width extras, delivery route (AR, CR, NR or N), Z15/Z25/Z35, UT class, inspection and cutting. Quantity per size matters because mills set rolling minimums.
What is the ASTM or EN equivalent of Q235GJE?
There is no exact equivalent. EN 10025-2 S235J2 (−20°C, 27 J) and ASTM A36 match strength only. JIS G3136 SN400C is the closest building steel, with a yield range and ratio limit, but it is tested at 0°C. For −40°C, EN 10025-3 S275NL is the usual European choice.

Conclusion

Q235GJE steel plate to GB/T 19879 is building structure plate with 235 MPa minimum yield, a capped yield window, a yield-ratio limit and 47 J impact at −40°C. It shares its chemistry with Q235GJB but proves toughness at its own letter. It is not general structural plate under GB/T 1591.

SHH STEEL delivers Q235GJE with the full GJ data set on an EN 10204 3.1 or 3.2 certificate: heat analysis, CEV, yield, yield ratio and impact. On request we add product analysis to GB/T 222, Z15, Z25 or Z35, GB/T 2970 UT, Class C tolerance, cutting and blasting.

We ship from Shanghai to buyers worldwide. Browse the full GB/T 19879 range or other carbon steel plates.

Ready to order? Send the drawing or cutting list, the certificate type and the destination port. Our engineers check the edition, letter and Z level before we quote, so the offer matches the drawing. Contact SHH STEEL for a mill-direct quotation on Q235GJE building steel plate.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X