ASME SA841 Grade E Class 4 Steel Plate | SA841 Gr.E Cl.4 TMCP Vessel Plate

ASME SA841 Grade E Class 4 is one of the two Class lines assigned to Grade E in ASME SA-841/SA-841M. Grades A, B and C use Class 1 and Class 2. Grade D uses Class 3 only. Grade E uses Class 4 and Class 5. Class 4 is the lower of those two Grade E lines: 485 MPa yield and 580–715 MPa tensile. Maximum nominal thickness for Grade E is 40 mm. As Direct Mill Supply by SHH STEEL, the plate is produced to ASME SA-841/SA-841M by thermo-mechanical control process.

Buyers write the same product as SA841 Grade E Class 4, SA841 Gr.E Cl.4, SA841GRE CL4, SA-841 Grade E Class 4, SA841 E4 and SA 841 Gr E Cl 4. ASTM A841 Grade E Class 4 is the companion mill specification. A purchase order that only says “SA841 Grade E” is incomplete. Class 5 on the same Grade raises yield to 515 MPa. Those two plates do not interchange.

Do not read the Class number as a simple ladder across the whole specification. Class 3 on Grade D is 690 MPa yield. Class 4 on Grade E is 485 MPa yield. The Class number follows the Grade. It does not mean “stronger than Class 3.” This page is not [SA841 Grade D Class 3] chemistry with a different stamp. Grade E carbon is 0.07% maximum. Nickel max is 0.60%. Molybdenum max is 0.30%. That ladle is not Grade D.

This page is not SA537 Cl.2. SA537 Class 2 is heat-treated C-Mn-Si. SA841 Grade E Class 4 is TMCP. It is not SA517 Gr.B QT alloy. It is not SA533 Type B Class 1 QT Mn-Mo-Ni. It is not ASME SA516 and not ASME SA387.

Thickness is the second filter. Grade E stops at 40 mm. An 80 mm Class 4 inquiry cannot be rolled as SA841 Grade E. Dual marking SA841 / A841 Grade E Class 4 is available. Certificates can be EN 10204 3.1 or 3.2. Company scope: China steel Mill Agent-SHH STEEL.

ASME SA841 Grade E Class 4 Steel Plate | SA841 Gr.E Cl.4 TMCP Vessel Plate

Brief Description
ASME SA841 Grade E Class 4 is TMCP vessel plate under ASME SA-841/SA-841M. Yield 485 MPa, tensile 580–715 MPa, max 40 mm. SHH STEEL supplies SA841 Gr.E Cl.4 mill-direct with 3.1 or 3.2 certificates.

SEO Title
ASME SA841 Grade E Class 4 Steel Plate | SA841 Gr.E Cl.4 TMCP Vessel Plate – SHH STEEL

SEO Keywords
ASME SA841 Grade E Class 4, SA841 Gr.E Cl.4, SA841GRE CL4, SA-841 Grade E Class 4, SA841 E4, TMCP vessel plate, SA841 Grade E Class 4 supplier

SEO Description
SHH STEEL supplies ASME SA841 Grade E Class 4 / SA841 Gr.E Cl.4 TMCP vessel plate, 485 MPa yield, max 40 mm. China Mill Direct Exporter, EN 10204 3.1/3.2. Contact now.

General Description

ASME SA841 Grade E Class 4 is one of the two Class lines assigned to Grade E in ASME SA-841/SA-841M. Grades A, B and C use Class 1 and Class 2. Grade D uses Class 3 only. Grade E uses Class 4 and Class 5. Class 4 is the lower of those two Grade E lines: 485 MPa yield and 580–715 MPa tensile. Maximum nominal thickness for Grade E is 40 mm. As Direct Mill Supply by SHH STEEL, the plate is produced to ASME SA-841/SA-841M by thermo-mechanical control process.

Buyers write the same product as SA841 Grade E Class 4, SA841 Gr.E Cl.4, SA841GRE CL4, SA-841 Grade E Class 4, SA841 E4 and SA 841 Gr E Cl 4. ASTM A841 Grade E Class 4 is the companion mill specification. A purchase order that only says “SA841 Grade E” is incomplete. Class 5 on the same Grade raises yield to 515 MPa. Those two plates do not interchange.

Do not read the Class number as a simple ladder across the whole specification. Class 3 on Grade D is 690 MPa yield. Class 4 on Grade E is 485 MPa yield. The Class number follows the Grade. It does not mean “stronger than Class 3.” This page is not [SA841 Grade D Class 3] chemistry with a different stamp. Grade E carbon is 0.07% maximum. Nickel max is 0.60%. Molybdenum max is 0.30%. That ladle is not Grade D.

This page is not SA537 Cl.2. SA537 Class 2 is heat-treated C-Mn-Si. SA841 Grade E Class 4 is TMCP. It is not SA517 Gr.B QT alloy. It is not SA533 Type B Class 1 QT Mn-Mo-Ni. It is not ASME SA516 and not ASME SA387.

Thickness is the second filter. Grade E stops at 40 mm. An 80 mm Class 4 inquiry cannot be rolled as SA841 Grade E. Dual marking SA841 / A841 Grade E Class 4 is available. Certificates can be EN 10204 3.1 or 3.2. Company scope: China steel Mill Agent-SHH STEEL.

Material Specification

This plate sits in the pressure vessel steel plates family. It does not sit with carbon steel plates that have no TMCP Class 4 table, and it does not sit with structural steel plates or ASTM A36/A36M. If a buyer sends an HSLA cutting list from ASTM A572 and a vessel drawing on the same email, those are two different books.

SA-20 still governs marking, testing location, retests and repair rules. TMCP does not cancel SA-20. Two tension tests from each plate-as-rolled remain the specification habit unless the order tightens the plan.

ASME SA841 Grade E Class 4 uses Grade E chemistry. Class 4 and Class 5 share that table. The Class only changes the tensile line.

Heat Analysis — ASME SA841 Grade E

Product analysis follows SA-20 / A20 tolerances on those heat limits. Carbon at 0.07% maximum is lower than Grade A (0.20%), Grade B (0.15%), Grade C (0.10%) and Grade D (0.09%). Sulfur at 0.005% maximum is in the same tight band as Grade D. Nickel max is 0.60%, which is Grade B territory, not Grade D’s 1.0–5.0% band. A ladle at 2% nickel is Grade D chemistry, not Grade E.

There is no “over 40 mm” manganese line because Grade E is not permitted over 40 mm. If chromium and molybdenum sit in a SA387 Gr.11 Cl.2 or SA387 Gr.22 Cl.2 window, the plate belongs on the Cr-Mo page. If the process is QT Mn-Mo-Ni, look at SA533 Type B Class 2. If the ladle is carbon only, look at SA516 Gr.70 or SA515 Gr.70.

SHH STEEL reports heat analysis on every certificate, including nickel, molybdenum, phosphorus and sulfur, and adds product analysis when SA-20 requires it.

Class 4 is the strength line on this page. Grade E only identifies the chemistry family.

Tensile Requirements — ASME SA841 Grade E Class 4

There is no “over 40 mm” column. The specification marks thicker Class 4 on Grade E as not applicable. Do not quote 65 mm Class 2 numbers from Grades A–C onto this page. Grades A–C never use Class 4.

Class 5 on the same Grade E is 515 MPa yield and 605–745 MPa tensile. A Class 4 heat cannot be stamped Class 5 because the coupon came in high. Class 3 belongs to Grade D and sits at 690 MPa yield. Do not call Class 4 “the next step after Class 3” without reading the Grade letter.

Density is 7.85 g/cm³ for weight take-off. Hardness is not a mandatory SA-841 Table 3 value. Typical TMCP Class 4 plate sits around 170–220 HB. If a drawing writes a hardness cap, put that number on the order. SHH STEEL will then test and print it. Do not read Brinell as a substitute for the 485 MPa yield test.

Charpy is not a hidden default. Export tanks and winter shells almost always add an impact temperature. Write the temperature, energy, location and orientation. Simulated PWHT coupons are common because shops that buy Grade E still want a vessel cycle.

Do not treat 485 MPa yield as permission to substitute high strength low alloy plates, EN 10025-6 structural QT plate, or SA302 Gr.C. Those books have their own chemistry and Code listings.

SA299 Gr.B, SA225 Gr.D, SA455 and SA285 Gr.C are also vessel plates. None of them is Grade E Class 4.

The practical question is whether Grade E Class 4 can replace SA537 Class 2 or SA841 Class 2. Only if the drawing and the allowable-stress line name SA-841 Grade E Class 4. Similar yield is not a substitution rule. The 40 mm cap is also not optional.

ASME SA841 Grade E Class 4 is used when the vessel wants a low-carbon TMCP Grade with 485 MPa yield and the wall stays inside 40 mm. Designers pick Grade E when they want tighter carbon and sulfur than Grades A–C, without jumping to Grade D’s 690 MPa Class 3 line and 1.0–5.0% nickel.

Allowable stress comes from ASME Section II Part D after the Code lists this Grade and Class. Do not copy a SA537 Cl.2 allowable and apply it here. Do not copy a Grade B Class 2 allowable either. The chemistry and the thickness cap are not the same.

Typical components are process shells, heads and courses written specifically to SA-841 Grade E Class 4. It is not cryogenic 3.5Ni plate like SA203 Gr.D or SA203 Gr.E. Grade E nickel is a limited TMCP addition, not a nickel-steel designation. Stainless work belongs on ASME SA240/SA240M, ASTM A240/A240M or stainless steel sheets and plates.

The TMCP temperature cap still applies. Except for Grade G, forming and PWHT stay at or below 650 °C, and only when clause 6.1 and any simulated coupons are satisfied. Do not run a 900 °C normalize on Grade E and expect Class 4 yield to remain.

SA841 Gr.E Cl.4 is killed, fine-grain TMCP plate with very low carbon. Welding is still Code welding.

Qualify procedures to ASME Section IX. Use low-hydrogen consumables. Carbon at 0.07% maximum and sulfur at 0.005% maximum help HAZ toughness. Nickel up to 0.60% and molybdenum up to 0.30% still belong in the carbon-equivalent calculation. Do not use a Grade A worksheet.

Preheat depends on thickness, restraint, hydrogen and the qualified WPS. After welding, many shops want PWHT. That cycle must stay inside the TMCP window and must be proven on mill coupons when the vessel specification already knows the hold.

Do not copy a SA387 Gr.12 Cl.2 Cr-Mo procedure or a SA533 Type A Class 1 QT procedure onto Grade E Class 4 without review. The fabricator owns the WPS. SHH STEEL supplies the plate and the test data.

The steel shall be killed and shall meet fine austenitic grain practice under ASME SA-20. Plates shall be produced by TMCP. Slab reheating, reduction schedule, finish temperature and accelerated cooling are the mill tools. There is no mandatory furnace normalize and no mandatory quench and temper in the specified condition.

If the vessel will be warm formed or post-weld heat-treated, the test coupons must follow that cycle. A coupon tested as-rolled does not prove a 620 °C shell hold. Ask for simulated PWHT when the vessel specification already knows the temperature and time.

This is not the normalize route used for SA516 Gr.60. It is not the QT route used for SA537 Cl.1 or SA517 Gr.E. SHH STEEL prints TMCP and Class 4 on the certificate so the inspector does not treat the plate as ordinary as-rolled carbon.

Usual delivery is TMCP Grade E Class 4 plate, 8 mm to 40 mm.

The mill test certificate lists ASME SA841 Grade E Class 4 and, when dual certified, ASTM A841 Grade E Class 4; heat number; heat analysis including Ni, Mo, P and S; product analysis when ordered; tensile results to the Class 4 table; TMCP statement; impact results when ordered; simulated PWHT results when ordered; and UT when ordered. Surface is vessel-plate quality. Shot blast and shop primer are available.

Certificates may be EN 10204 3.1 or EN 10204 3.2. Third-party surveyors can witness rolling, cooling and testing when the order names the agency.

Usual supply range from SHH STEEL for SA841 Gr.E Cl.4 TMCP vessel plate:

• Thickness: 8 mm – 40 mm. That 40 mm ceiling is the Grade E rule in SA-841, not a mill preference
• Width: 1500 mm – 4000 mm, subject to the Grade E rolling schedule
• Length: 3000 mm – 12000 mm
• Cut-to-length shells, dish-head blanks and nest sizes inside those limits

A 45 mm inquiry is outside Grade E. Do not “see if the mill can roll it” and still stamp SA841 Grade E Class 4. Grades A, B and C go to 100 mm, but they do not carry Class 4.

Structural lengths belong on EN 10025-2 or JIS G3106. Weathering plate belongs on EN 10025-5 or Corten A/B. Fine-grain structural belongs on EN 10025-3 or EN 10025-4. QT structural belongs on EN 10025-6.

Dimensional limits follow ASME SA-20. Thickness tolerance, width, length, flatness and camber are vessel-plate rules.

TMCP plate can move during accelerated cooling. Flatness should be written if the head shop is tight. Ultrasonic testing to A435, A577 or A578 is common on Grade E plate. Extra-flatness and edge-camber limits are negotiated items, not assumed extras.

Most export ASME SA841 Grade E Class 4 orders add extras. The specification does not assume them.

Charpy V-notch. Temperature, absorbed energy, specimen location and orientation.

Simulated PWHT and warm forming. Same-heat coupons follow the vessel cycle. Tensile and impact are then run on those coupons.

NDE. UT to A435 / A577 / A578. Edge MT or PT after cutting when the shop wants it.

Restricted P, S and CEV. Table 1 is already tight on sulfur. Some projects go tighter on phosphorus and carbon equivalent.

Through-thickness / Z testing. When lamellar tearing is a design concern.

Third-party inspection. EN 10204 3.2, with the agency named on the order.

If an item is not written, it is not tested and it is not printed as if it were.

There is no one-to-one dual stamp outside ASTM A841. The names below are project comparisons. Chemistry, TMCP route, 40 mm cap and impact temperature still have to match the purchase order.

DIN 17100, ASTM A516, ASME SA515 and ASTM A285 are not Grade E Class 4. SHH STEEL will dual-certify SA841 / A841. EN, JIS or GB dual marking is only when the mill heat meets both books and the order says so.

Ship plate inquiries belong on shipbuilding steel plates or BV Rules. Weathering inquiries belong on weathering steel plates. Stainless inquiries belong on stainless steel products, JIS G4305 or AISI stainless.

Other vessel comparisons: SA203 Gr.B, SA302 Gr.C, A516 Gr.70, SA533 Type C Class 2, SA517 Gr.P.

SHH STEEL works as a China Mill Direct Exporter for plates to ASME SA-841/SA-841M. On ASME SA841 Grade E Class 4 that means mill pricing, dual SA841/A841 marking, Grade E chemistry with carbon at 0.07% max and sulfur at 0.005% max, recorded TMCP delivery, Class 4 tensile results at 485 MPa yield and 580–715 MPa tensile, the 40 mm ceiling respected, 3.1 as standard and 3.2 when specified.

We keep Grade and Class on the order. Grade E Class 4 is not Grade E Class 5. Grade E is not Grade D and is not Grade C. SA841 is not SA516 Gr.55. SA841 is not SA387 Gr.91 Cl.2. SA841 Gr.E Cl.4 is not SA533 Type C Class 1. If the drawing names 80 mm at this Grade, we will say Grade E cannot be used. If it names Class 5, we will not ship Class 4 and call it close. If the shop plans a 900 °C form, we will say TMCP is the wrong process before the slab is booked.

Company scope: China steel Mill Agent-SHH STEEL.

ASME SA841 Grade E Class 4 Steel Plate is TMCP pressure-vessel plate under ASME SA-841/SA-841M, limited to 40 mm, with 485 MPa yield and 580–715 MPa tensile. Whether the inquiry says SA841 Grade E Class 4, SA841 Gr.E Cl.4, SA841GRE CL4 or SA-841 Grade E Class 4, SHH STEEL supplies plate with Grade E chemistry, recorded TMCP delivery, Class 4 tensile results, and EN 10204 3.1 or 3.2 certification.

As a China mill Distributor, SHH STEEL provides ASME SA841 Grade E Class 4 / SA841 Gr.E Cl.4 TMCP Vessel Plate for ASME Section VIII work that actually names this Grade and Class.

Contact SHH STEEL for mill rolling, dual SA841/A841 marking, simulated PWHT testing, 3.2 inspection or a quotation.

ASME SA841 Grade E Class 4 Steel Plate, SA841 Gr.E Cl.4, SA841GRE CL4, SA-841 Grade E Class 4, TMCP vessel plate, Direct Mill Supply by SHH STEEL