ASTM A213 UNS S35045 Stainless Steel Tube
What is ASTM A213 UNS S35045 Stainless Steel Tube
ASTM A213 / A213M lists UNS S35045 among the austenitic stainless grades that carry no common TP letter — the Grade column prints an ellipsis and the UNS number identifies the alloy. The chemistry is a high-chromium, high-nickel Al–Ti window: carbon 0.06–0.10%, manganese ≤1.50%, chromium 25.0–29.0%, nickel 32.0–37.0%, titanium 0.15–0.60%, aluminum 0.15–0.60%, and copper ≤0.75%. Commercially buyers know it as Alloy 803 class tube chemistry; that shop name still needs ASTM A213 (or the separate ASME SA-213 adoption) on the purchase order so seamless-tube minimum-wall, test, and marking clauses apply.
SHH STEEL can supply ASTM A213 UNS S35045 stainless steel tube as seamless cold-finished and hot-finished product in the usual boiler, furnace, and heat-exchanger OD × wall / BWG band, shipped with EN 10204 3.1 mill test certificates that report the full Al–Ti–Cr–Ni set and the Table 4 tensile and hardness results (70 ksi [485 MPa] / 25 ksi [170 MPa], hardness max 192 HBW / 90 HRB). Dual A213 / SA-213 marking is available only when the purchase order asks for both independent standards. Browse high-nickel austenitic sisters on the A213/A213M hub.
Do not paste an Alloy 800 / N08800 chemistry block onto an S35045 certificate — chromium opens to 25.0–29.0% (vs ~19–23% on 800), nickel sits at 32.0–37.0%, and carbon is a 0.06–0.10% range rather than the broader 800 max. Sister grades under the same ASTM standard include A213 TP310S, A213 TP310H, A213 UNS S31002, A213 UNS S30815, and A213 UNS S30615. A213 covers seamless tube only — cold-finished versus hot-finished is the process choice, not a WLD/HCW manufacturing type.
Chemical Composition of A213 UNS S35045
UNS S35045 chemistry is built for high-temperature oxidation and carburization-leaning service inside a 25–29% Cr / 32–37% Ni window with deliberate aluminum and titanium additions (each 0.15–0.60%). Carbon is a range (0.06–0.10%), not a low-C max. Molybdenum and nitrogen are no-requirement ellipses — this is not a PREN-first chloride grade. Melting analysis is mandatory; product analysis applies only when ordered through A1016 / A480 A1.1. There is no TP grade letter — order and mark by UNS S35045.
The tables below reproduce the melt limits from the public A213 stainless chemistry table, product-analysis limits from A480 Table A1.1 practice, and a short snapshot against Alloy 800 (N08800) / TP310S. Confirm the ordered edition before treating secondary catalogues as acceptance text. UNCERTAIN: A480 product-tolerance digits for Al 0.15–0.60 and Ti 0.15–0.60 (and whether any Al+Ti combined rule from neighboring Ni-base footnotes applies) are applied from sister Al/Ti austenitic practice — confirm the A480 edition if product analysis is contractual. Public Table 2 chemistry footnotes J (Al+Ti combined) attach to N08811 in the excerpt, not automatically to S35045 — do not invent a combined Al+Ti floor for S35045 unless the ordered edition says so.
Melting analysis (heat / ladle analysis)
| Element | UNS S35045 melting analysis |
|---|---|
| Carbon (C) | 0.06 – 0.10 |
| Manganese (Mn) | ≤ 1.50 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.015 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 25.0 – 29.0 |
| Nickel (Ni) | 32.0 – 37.0 |
| Molybdenum (Mo) | … (no requirement) |
| Nitrogen (N) | … (no requirement) |
| Niobium (Nb) | … (no requirement) |
| Titanium (Ti) | 0.15 – 0.60 |
| Aluminum (Al) | 0.15 – 0.60 |
| Copper (Cu) | ≤ 0.75 |
Source: ASTM A213/A213M stainless chemistry table for UNS S35045 (public htpipe A213 PDF excerpt — _ref_a213.txt A213/A213M − 13). Aluminum 0.15–0.60% and titanium 0.15–0.60% must both appear on the certificate; an MTC that only shows “Alloy 803 nickname chemistry” without the A213 ranges is incomplete.
Product analysis — A480/A480M Table A1.1 tolerances applied
| Element | Melting | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | 0.06 – 0.10 | 0.01 under / over | 0.05 – 0.11 |
| Manganese (Mn) | ≤ 1.50 | 0.04 over | ≤ 1.54 |
| Phosphorus (P) | ≤ 0.045 | 0.010 over | ≤ 0.055 |
| Sulfur (S) | ≤ 0.015 | 0.005 over | ≤ 0.020 |
| Silicon (Si) | ≤ 1.00 | 0.05 over | ≤ 1.05 |
| Chromium (Cr) | 25.0 – 29.0 | 0.25 under / over | 24.75 – 29.25 |
| Nickel (Ni) | 32.0 – 37.0 | 0.15 under / 0.20 over (UNCERTAIN for 32–37 band) | 31.85 – 37.20 |
| Titanium (Ti) | 0.15 – 0.60 | 0.05 under / over (UNCERTAIN) | 0.10 – 0.65 |
| Aluminum (Al) | 0.15 – 0.60 | 0.05 under / over (UNCERTAIN) | 0.10 – 0.65 |
| Copper (Cu) | ≤ 0.75 | 0.03 over | ≤ 0.78 |
Reading note: product analysis is not automatic — invoke it on the purchase order. Al and Ti product digits above are sister-practice working values labeled UNCERTAIN until the ordered A480 edition is checked.
Cr / Ni / Al–Ti snapshot — TP310S / N08800 / S35045
| Element | TP310S (S31008) | Alloy 800 (N08800) | UNS S35045 |
|---|---|---|---|
| C | ≤ 0.08 | ≤ 0.10 | 0.06 – 0.10 |
| Cr | 24.0 – 26.0 | 19.0 – 23.0 | 25.0 – 29.0 |
| Ni | 19.0 – 22.0 | 30.0 – 35.0 | 32.0 – 37.0 |
| Al | … | 0.15 – 0.60 | 0.15 – 0.60 |
| Ti | … | 0.15 – 0.60 | 0.15 – 0.60 |
| Cu | … | ≤ 0.75 | ≤ 0.75 |
S35045 shares the Al–Ti idea with Alloy 800 but pushes chromium into a 25–29% band closer to 310-family oxidation framing while keeping nickel in the mid-30% range — it is not a drop-in 800 or 310S substitute.
Mechanical Properties of A213 UNS S35045
Table 4 for UNS S35045 sets tensile min 70 ksi [485 MPa], yield min 25 ksi [170 MPa], elongation min 35%, and hardness max 192 HBW / 200 HV or 90 HRB. That pair matches the soft L-grade strength style rather than the high-N 6Mo floors — do not apply an S31254 or S31277 checklist to an S35045 lot, and do not invent a higher tensile floor because Alloy 803 marketing sheets sometimes quote different product forms.
| Property | UNS S35045 requirement |
|---|---|
| Tensile strength, min | 70 ksi [485 MPa] |
| Yield strength (0.2% offset), min | 25 ksi [170 MPa] |
| Elongation in 2 in. or 50 mm, min | 35% |
| Hardness, max | 192 HBW / 200 HV or 90 HRB |
Source: ASTM A213/A213M Table 4 for UNS S35045 (public A213–13 excerpt). Mechanical property requirements generally do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or thinner than 0.015 in. [0.4 mm] wall. Flattening and flaring tests remain lot requirements under A213.
A tensile-only MTC that omits aluminum or titanium is incomplete documentation practice for this grade. Hardness follows the commodity 192 HBW / 90 HRB ceiling — unlike the higher hardness caps on S31254 / S31277.
Dimensions and Tolerances
Dimensional supply for ASTM A213 UNS S35045 remains tube language — OD × min wall (or average wall) and BWG / gauge — covering furnace, reformer, and high-temperature heat-exchanger sizes rather than leading with ASME B36.19 pipe schedules. Usual A213 sizes run from about 1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD with min wall about 0.015–0.500 in. [0.4–12.7 mm]; other diameters by agreement. Furnace and radiant-tube datasheets almost always assume a minimum-wall reading — state wall basis on the purchase order.
OD and wall variations follow ASTM A1016/A1016M as invoked by A213. Cold-finished tubes commonly hold tighter OD; hot-finished tubes allow wider windows. High-nickel Al–Ti alloys can be drawing-sensitive on thin walls — confirm mill capability for the exact OD × wall early on large furnace cut lists.
Length is ordered as specific cut lengths for furnace / exchanger bundles or as random mill lengths. End finish follows the fabrication drawing. B36.19 schedule references may appear only as a secondary commercial size hint — they are not the primary A213 size story for S35045 tube.
Equivalent Grades
Equivalence language around S35045 tube often collapses “Alloy 803” nicknames across plate, bar, and tube product forms. ASTM A213 UNS S35045 is the governing designation for this article; commercial Alloy 803 aliases point to similar Al–Ti high-Ni/Cr chemistry families but are not automatic substitutes on an A213 MTC without matching the seamless-tube standard clauses.
| Designation | Notes |
|---|---|
| ASTM A213 / A213M UNS S35045 | Governing ASTM seamless boiler / HX tube product standard — no TP letter |
| UNS S35045 | Unified number that uniquely identifies the alloy |
| Alloy 803 (commercial) | Shop name for Al–Ti 25Cr–35Ni-class chemistry — do not replace A213 product marking |
| Near Alloy 800 / 310 sisters (not substitutes) | N08800 / TP310S share high-temp themes but different Cr–Ni–Al–Ti packages |
| ASME SA-213 UNS S35045 | Separate Code Book adoption — dual-mark only when the PO asks |
Compare high-temperature sisters such as A213 TP310S, A213 TP310H, and A213 UNS S30815 on the A213/A213M hub before freezing the furnace tube list. Plate chemistry under A240 is a related alloy story, not an automatic tube MTC substitute.
Heat Treatment and Delivery Condition
UNS S35045 under ASTM A213 is furnished solution treated at a minimum of 2000 °F [1100 °C], then cooled in still air or faster — a cooling path that differs from the water-or-rapid-cool language printed for most neighboring austenitic rows. Do not force a mandatory water quench stamp onto S35045 if the ordered edition still allows still-air cool or faster; likewise do not invent a slower furnace cool that the table does not permit. Public Table 3 does not print a mandatory grain-size number for this grade (ellipsis).
Cold-finished versus hot-finished is a process and dimensional route, not a second product standard. Both routes still require the 2000 °F solution treatment on finished tube. Aluminum and titanium in the melt do not create an H-grade grain-size obligation under the public Table 3 excerpt.
UNCERTAIN: public Table 3 OCR places a Footnote F marker on the S35045 heat-treatment row. Confirm ordered-edition footnote attachment — if Footnote F applies, quench/cool capability must be sufficient to prevent carbide re-precipitation as demonstrable by A262 Practice E capability, and the manufacturer need not run the test unless the purchase order specifies it (Supplementary Requirement S4). Reconcile Footnote F language with the printed “still air cool or faster” path on the ordered edition rather than assuming a water-only quench.
Corrosion Resistance
S35045’s corrosion / oxidation story is high-temperature scaling and carburization-leaning resistance from the 25–29% Cr / 32–37% Ni balance plus Al and Ti additions — not a seawater PREN narrative. Molybdenum is a no-requirement ellipse, so wet chloride cooler framing still belongs with A213 UNS S31254 or A213 TP316L, not with S35045 as a primary chloride strategy.
Relative to TP310S, the higher nickel and Al–Ti package lean the grade toward Alloy 800-family high-temp process service while keeping chromium in a 310-like oxidation band. When IGC after fabrication is a project concern, order A262 Practice E explicitly rather than assuming every mill runs it by default.
Applications of A213 UNS S35045 Tube
Buyers specify ASTM A213 UNS S35045 when furnace, reformer, or high-temperature heat-exchanger duty needs Alloy 803 class chemistry — 25–29% Cr, 32–37% Ni, and balanced Al–Ti — as seamless A213 tube rather than a generic 310S or 800 substitution. Typical placements include radiant and reformer tubes, furnace coils, muffles, and high-temperature process exchangers where oxidation and carburization resistance drive grade selection.
| Service theme | Why S35045 is considered |
|---|---|
| Furnace / radiant / reformer tube | 25–29 Cr / 32–37 Ni with Al + Ti 0.15–0.60% each |
| High-temperature process exchangers | Alloy 803 class chemistry under seamless A213 product rules |
| Carburization-leaning atmospheres | Al–Ti bearing high-Ni austenitic window (project-specific) |
| Code dual-mark furnace lists | A213 product form with optional SA-213 stencil when PO asks |
If the duty is wet chloride PREN rather than high-temperature oxidation, look at A213 UNS S31254 or A213 UNS S31277 instead of forcing S35045 into a seawater narrative.
Weldability
S35045 tube welds with high-nickel austenitic practices using matching or near-matching Alloy 803 / high-Ni fillers selected for the joint design and service temperature. Aluminum and titanium in the base metal should be respected in WPS development; heat input control and post-weld cleaning still matter for high-temperature cyclic service. Do not assume a soft ER308L or ER310 deposit will match 32–37% Ni / Al–Ti performance without a qualified procedure review.
For tube-to-tubesheet and coil welding, keep filler chemistry aligned with the base-metal Cr–Ni–Al–Ti window and confirm any project restriction on residual copper or aluminum. When the datasheet demands A262 Practice E on welded samples, state that on the purchase order.
Surface Finishes
Standard delivery for ASTM A213 UNS S35045 from SHH STEEL is solution annealed and pickled, with a clean ID/OD suitable for furnace and high-temperature exchanger fabrication. Bright annealed or polished finishes are available by agreement when the process side needs lower roughness or a brighter appearance.
State finish expectations on the enquiry together with OD × wall and end preparation. Do not assume a bright finish from a generic “Alloy 803 tube” line item — pickled anneal after the 2000 °F solution treatment is the default path unless the purchase order says otherwise.
Inspection and Testing
Lot testing for ASTM A213 UNS S35045 follows the tension, hardness, flattening, and flaring requirements of A213 together with A1016/A1016M. Chemistry is verified on the heat (and on product when ordered) — carbon 0.06–0.10%, chromium 25.0–29.0%, nickel 32.0–37.0%, aluminum 0.15–0.60%, and titanium 0.15–0.60% must all clear. Non-destructive examination follows the ordered edition and any purchaser supplementary requirements.
EN 10204 3.1 mill test certificates from SHH STEEL report ladle chemistry including Al and Ti, tensile and hardness results (70/25 ksi; 192 HBW / 90 HRB), heat-treatment condition at ≥2000 °F [1100 °C] with still-air cool or faster, and dimensions. Ask for A262 Practice E on the PO when IGC capability must be demonstrated by actual test. Third-party witness and dual A213/SA-213 marking are available when specified.
Packaging and Shipping
S35045 tubes ship in capped or plugged bundles with weather protection suited to the destination and transport mode. Cut lengths for furnace and exchanger bundles are labeled by heat and size; export packing uses wooden cases or steel-frame crates when the route requires them.
Marking includes ASTM A213, UNS S35045, size, heat number, and SHH STEEL identification. Dual SA-213 marking appears only when the purchase order requests it. Packing lists reference the same heat numbers shown on the EN 10204 3.1 certificates.
Why Choose SHH STEEL
SHH STEEL treats ASTM A213 UNS S35045 as a specification Alloy 803 class product: C 0.06–0.10%, Cr 25.0–29.0%, Ni 32.0–37.0%, Al 0.15–0.60%, Ti 0.15–0.60%, Table 4 70/25 ksi, hardness max 192 HBW / 90 HRB, and the 2000 °F solution anneal with still-air cool or faster are checked together before a heat is offered. Quotations state OD × wall / BWG, wall basis, finish route, A262 options, and whether dual A213/SA-213 marking is required.
We refuse substitutions that stamp Alloy 800 or TP310S onto an S35045 line item without clearing the 25–29% Cr / 32–37% Ni / Al–Ti package, or that omit aluminum from the MTC. EN 10204 3.1 documentation includes Al and Ti together with Cr and Ni. Compare sisters on the A213/A213M hub before freezing the furnace tube list.
Supply Capability
SHH STEEL supplies ASTM A213 UNS S35045 seamless stainless steel tube against purchase-order chemistry, mechanical, and dimensional requirements — cold-finished or hot-finished — with EN 10204 3.1 mill test certificates. The capability table below summarizes the enquiry window; it is not a frozen warehouse SKU list.
| Capability | SHH STEEL supply window for UNS S35045 |
|---|---|
| Product form | Seamless cold-finished / hot-finished boiler, superheater, and heat-exchanger tube |
| Grade / marking | ASTM A213 UNS S35045; dual A213/SA-213 only when PO asks |
| Size band | Typical OD × min wall (or average wall) within the A213 ~1/8 in. ID to 5 in. OD / 0.015–0.500 in. wall window; other diameters by agreement |
| Documentation | EN 10204 3.1 MTC with Al–Ti–Cr–Ni chemistry and Table 4 70/25 ksi tensile/hardness |
| Testing options | A262 Practice E, PMI, third-party witness, supplementary NDE per PO |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
Stock / Available sizes
SHH STEEL quotes S35045 against a stock-and-mill enquiry range rather than a frozen SKU/tonnage list. Representative OD × wall / BWG combinations for furnace, reformer, and high-temperature heat-exchanger tube appear below.
| Item | Typical stock / enquiry range for UNS S35045 |
|---|---|
| Outside diameter | 19.05, 25.4, 31.8, 38.1, 42.4, 50.8, 60.3, 76.2 mm (and other furnace/HX ODs on enquiry; through the usual A213 ~5 in. [127 mm] band) |
| Wall / BWG | BWG 10–18 class walls and metric min-wall equivalents; heavier walls by agreement |
| Common OD × wall examples | 25.4 × 2.11 mm; 31.8 × 2.77 mm; 38.1 × 2.77 mm; 42.4 × 3.56 mm; 50.8 × 3.05 mm; 60.3 × 3.91 mm — illustrative, confirm min vs average wall |
| Length | Cut lengths for furnace / exchanger bundles; bends and random mill lengths on enquiry |
| Special | Non-standard OD/wall, bright anneal, dual A213/SA-213, A262 Practice E, third-party witness — confirm before heat reservation |
Send OD × wall (or BWG), wall basis (min or average), finish route, quantity or cut list, marking (A213 or dual A213/SA-213), and any A262 / NDE extras with the enquiry so the Al–Ti chemistry and 2000 °F still-air-or-faster anneal path are reserved with the heat.
FAQ
-
Is ASTM A213 the same as ASME SA-213 for UNS S35045?
- No. ASTM A213 / A213M is the ASTM International product specification for seamless boiler, superheater, and heat-exchanger tubes; ASME SA-213 / SA-213M is the separate ASME Code Book adoption. Dual-mark only when the purchase order asks for both names on the stencil and MTC. Chemistry and tensile floors align closely for a given referenced edition, but the standards remain independent.
-
Why does S35045 have no TP letter under A213?
- The A213 stainless chemistry table prints an ellipsis in the Grade column for S35045 — there is no common TP designation, and the UNS number identifies the alloy. Order, mark, and certify as UNS S35045 rather than inventing a TP803 letter code on the stencil. Commercial Alloy 803 nicknames remain useful shop language but do not replace the UNS product marking.
-
What is the chemistry of ASTM A213 UNS S35045?
- Public A213 melt limits for S35045 are C 0.06–0.10%, Mn ≤1.50%, P ≤0.045%, S ≤0.015%, Si ≤1.00%, Cr 25.0–29.0%, Ni 32.0–37.0%, Ti 0.15–0.60%, Al 0.15–0.60%, and Cu ≤0.75%. Molybdenum, nitrogen, and niobium are no-requirement ellipses. Confirm the ordered A213/A213M edition before treating catalogue reprints as acceptance text.
-
S35045 vs Alloy 800 (N08800) — can I substitute?
- Not as an automatic substitute. Alloy 800 (N08800) uses Cr 19.0–23.0% / Ni 30.0–35.0% with Al and Ti each 0.15–0.60%. S35045 pushes chromium to 25.0–29.0% and nickel to 32.0–37.0% with a carbon range of 0.06–0.10%. They share an Al–Ti theme but are different UNS rows — substitute only when the engineer revises the datasheet.
-
S35045 vs TP310S — which high-Cr A213 tube should I order?
- TP310S is a 24–26% Cr / 19–22% Ni grade without mandatory Al/Ti, typically for oxidation service with a 75/30 ksi tensile pair. S35045 keeps high chromium (25–29%) but adds 32–37% nickel plus Al and Ti, with a 70/25 ksi tensile pair and a unique still-air-or-faster cool path. Choose based on whether the datasheet wants Alloy 803 class chemistry or classic 310S.
-
Is Alloy 803 the same as ASTM A213 UNS S35045?
- Alloy 803 is a commercial shop name for Al–Ti 25Cr–35Ni-class chemistry in the S35045 family. It is useful language on drawings and RFQs, but the governing ASTM seamless-tube product designation for this page is ASTM A213 UNS S35045. Always put A213 (and SA-213 only if Code dual-mark is required) on the purchase order.
-
What tensile and hardness floors does Table 4 set for S35045?
- Tensile min 70 ksi [485 MPa], yield min 25 ksi [170 MPa], elongation min 35%, hardness max 192 HBW / 200 HV or 90 HRB. That pair is softer than high-N 6Mo grades — do not apply an S31254 or S31277 checklist to S35045.
-
What heat treatment does A213 require for UNS S35045?
- Solution treatment at a minimum of 2000 °F [1100 °C] followed by still air cool or faster — not the water-or-rapid-cool language printed for most neighboring austenitic rows. Confirm Footnote F attachment on the ordered edition and reconcile it with the still-air path. No mandatory grain-size number is printed for this row in the public Table 3 excerpt.
-
Does ASTM A213 UNS S35045 include welded or HCW tube?
- No. ASTM A213 covers seamless boiler, superheater, and heat-exchanger tubes only. Cold-finished versus hot-finished is the process choice inside seamless manufacture. Welded or HCW product forms belong under other ASTM stainless tubular standards, not under an A213 S35045 line item.
-
Minimum wall vs average wall for A213 S35045 — which should I specify?
- A213 treats minimum wall as the default ordering basis unless the purchase order specifies average wall. Furnace and heat-exchanger datasheets almost always assume minimum wall. Write “min wall” or “average wall” explicitly on the PO rather than leaving the mill to infer intent from a BWG number alone.
-
Can you dual-certify A213 and SA-213 UNS S35045?
- Yes, when the purchase order asks for both independent standards on the stencil and MTC. ASTM A213 and ASME SA-213 remain separate documents; dual marking is a commercial/documentation choice, not an automatic merge of the two names into one title. SHH STEEL will not put SA-213 in the H1 or SEO title of the product page — that stays ASTM A213.
Conclusion
ASTM A213 UNS S35045 is the Alloy 803 class Al–Ti seamless stainless steel tube grade for furnace, reformer, and high-temperature heat-exchanger service when Cr 25.0–29.0%, Ni 32.0–37.0%, and balanced Al–Ti 0.15–0.60% — not a TP310S or Alloy 800 substitution — drive grade selection. SHH STEEL supplies cold-finished and hot-finished seamless tube in the usual OD × wall / BWG band, solution annealed at 2000 °F [1100 °C] with still-air cool or faster, tested to Table 4 70/25 ksi and hardness limits, and documented on EN 10204 3.1 certificates — with dual SA-213 marking only when the purchase order asks.
Contact: admin@steelspecs.com