ASTM A213 TP316L Stainless Steel Tube | ASTM A213 Stainless Steel - SHH STEEL

ASTM A213 TP316L Stainless Steel Tube

ASTM A213 TP316L / UNS S31603 seamless boiler, superheater and heat-exchanger tube with C ≤0.035% (Footnote D to 0.040% on small-OD / light-wall), Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00%, a 70/25 ksi Table 4 floor, hardness max 192 HBW / 90 HRB, and a 1900 °F solution anneal. SHH STEEL supplies cold-finished and hot-finished seamless tube with EN 10204 3.1 MTCs.
Grade
TP316L / UNS S31603
Standard
ASTM A213 / A213M
Product form
Seamless boiler / superheater / heat-exchanger tube (cold-finished and hot-finished)
Size
Typical OD × min wall (or average wall) within ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD and ~0.015–0.500 in. [0.4–12.7 mm] wall; other diameters by agreement
Share:
Overview
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASTM A213 TP316L Stainless Steel Tube

ASTM A213 / A213M is the ASTM International product specification for seamless ferritic and austenitic alloy-steel boiler, superheater, and heat-exchanger tubes. Grade TP316L is the low-carbon molybdenum-bearing austenitic listed under UNS S31603, chosen when a chloride-leaning exchanger still needs as-welded tube-to-tubesheet integrity. Table chemistry caps carbon at 0.035% on the melt (with Footnote D allowing 0.040% max on small-diameter or thin-wall tube that needs many drawing passes), keeps chromium at 16.0–18.0%, nickel at 10.0–14.0%, and molybdenum at 2.00–3.00% — the same Mo window as A213 TP316, but with the L-grade carbon ceiling that reduces sensitization risk after welding. Buyers who write “316L HX tube” on a bill of materials still need to name A213 (or the separate ASME SA-213 adoption) on the purchase order so the mill applies the tube product standard, minimum-wall rules, hardness tests, and marking clauses.

SHH STEEL can supply ASTM A213 TP316L stainless steel tube as seamless cold-finished and hot-finished product in the usual boiler and heat-exchanger OD × wall / BWG band, shipped with EN 10204 3.1 mill test certificates that report the full ladle chemistry — including both the carbon ceiling and the molybdenum window — and the Table 4 tensile and hardness results. When a project also needs ASME Code Book marking, we dual-mark A213 / SA-213 on the same lengths only if the purchase order says so — ASTM A213 and ASME SA-213 remain two independent standards. Browse the grade family on the A213/A213M hub.

Commercially, TP316L tube is still called 316L, low-carbon 316, or S31603 boiler/HX tube; none of those shop names replace the ASTM grade on the MTC or stencil. Sister grades under the same ASTM standard include A213 TP316, A213 TP316H, A213 TP304L, A213 TP317L, and A213 TP321. A213 covers seamless tube only — there is no welded or HCW manufacturing type under this product standard — so cold-finished versus hot-finished seamless route is the finish/process choice, not a WLD/HCW stencil letter.

Chemical Composition of A213 TP316L

Two chemistry layers matter for TP316L under ASTM A213. The melting (heat or ladle) analysis is mandatory for every heat under the stainless chemistry table, while product analysis on finished tube applies only when Supplementary Requirement wording or the purchase order invokes product analysis through the general requirements in ASTM A1016/A1016M. Product-analysis tolerances are not reprinted as a standalone chemistry table inside A213 itself; when ordered, they typically flow from ASTM A480/A480M Table A1.1 via that general-requirements path. SHH STEEL reports the actual ladle carbon at or below the 0.035% ceiling (or the Footnote D 0.040% ceiling when that thin-wall path applies) and the molybdenum inside 2.00–3.00%, and does not advertise a tighter “0.030 / high-Mo shop grade” that the ASTM stainless table does not publish.

The tables below reproduce the heat analysis for TP316L / UNS S31603 and the product-analysis limits that result from applying A480 Table A1.1 tolerances. Values are maximum unless a range is shown, and an ellipsis (…) means the ordered edition sets no requirement for that element. Confirm the ordered A213/A213M edition on the purchase order — table number (Table 1 versus Table 2 for stainless) and any nitrogen row can shift by year.

Melting analysis (heat / ladle analysis)

Element TP316L (UNS S31603) melting analysis
Carbon (C) ≤ 0.035 D
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 16.0 – 18.0
Nickel (Ni) 10.0 – 14.0
Molybdenum (Mo) 2.00 – 3.00
Nitrogen (N) … (no requirement; analysis method by agreement when reported)

Source: ASTM A213/A213M stainless chemistry table for Grade TP316L / UNS S31603 (public specification table excerpts cross-checked). Footnote D: for small diameter or thin walls, or both, where many drawing passes are required, a carbon maximum of 0.040% is necessary in Grades TP304L, TP304LN, TP316L, and TP316LN. Confirm the ordered edition before treating any secondary catalogue as the acceptance text.

Product analysis — A480/A480M Table A1.1 tolerances applied to melt limits

Element Melting Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.035 0.01 over ≤ 0.045
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 16.0 – 18.0 0.20 under / over 15.80 – 18.20
Nickel (Ni) 10.0 – 14.0 0.10 under / 0.15 over 9.90 – 14.15
Molybdenum (Mo) 2.00 – 3.00 0.05 under / 0.10 over 1.95 – 3.10

TP316L’s chemistry story has two equal pillars: low carbon for as-welded intergranular resistance, and molybdenum for chloride pitting resistance. Holding C ≤0.035% on the melt (or ≤0.040% under Footnote D) reduces the carbon available to form chromium carbides at grain boundaries during tube-to-tubesheet welding; Mo at 2.00–3.00% is required and must appear on the certificate — a PMI report that only shows Cr and Ni does not clear the grade. Chromium and nickel match the TP316 bands (16–18% Cr, 10–14% Ni), not the TP304L 18–20% / 8–12% windows; do not mix A312 pipe chemistry rows onto an A213 tube MTC.

When product analysis is ordered, finished tube may read up to C 0.045%, Mn 2.04%, P 0.055%, S 0.035%, and Si 1.05%, with Cr 15.80–18.20%, Ni 9.90–14.15%, and Mo 1.95–3.10%. Those are the only product limits we quote from the A480 A1.1 path. Put any tighter project carbon or molybdenum ceiling on the purchase order before the heat is selected, and say whether Footnote D applies to the OD × wall you are buying.

Mechanical Properties of A213 TP316L

ASTM A213 Table 4 sets the tensile acceptance floor for TP316L at 70 ksi [485 MPa] tensile strength and 25 ksi [170 MPa] yield strength (0.2% offset), with elongation of 35% minimum in 2 in. or 50 mm. That 70/25 ksi pair matches TP304L and sits below the 75/30 ksi floor on standard TP316 — the trade-off that comes with guaranteed low carbon while keeping the molybdenum window. Unlike many ASTM A312 pipe rows for the same UNS number, A213 Table 4 also lists a hardness maximum for TP316L of 192 HBW / 200 HV or 90 HRB, and hardness tests are part of the lot acceptance scheme in the product standard. Every lot sampled under the edition’s specimen rules must meet those numbers after the final solution treatment.

Property TP316L requirement (Table 4)
Tensile strength, min 70 ksi [485 MPa]
Yield strength (0.2% offset), min 25 ksi [170 MPa]
Elongation in 2 in. or 50 mm, min 35%
Hardness, max 192 HBW / 200 HV or 90 HRB

Source: ASTM A213/A213M Table 4 for TP316L / UNS S31603 (public specification summaries). Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or thinner than 0.015 in. [0.4 mm] wall. Flattening and flaring tests are also required on a lot basis for finished tube; they sit beside tension and hardness rather than replacing them.

Dual TP316/TP316L certification is common when a heat meets the tighter carbon rules and still clears the higher 75/30 ksi TP316 tensile floor plus both hardness maxima — ask for that dual marking on the purchase order rather than assuming it from a PMI gun. For creep-range boiler service that needs a controlled carbon floor and grain-size language, open A213 TP316H rather than stretching low-carbon TP316L into H-grade framing.

Dimensions and Tolerances

Dimensional supply for ASTM A213 TP316L is tube language — outside diameter × wall thickness (minimum wall or average wall) and, commercially, BWG / gauge — not ASME B36.19 pipe schedules as the primary size story. The sizes usually furnished under A213 run from about 1/8 in. [3.2 mm] inside diameter to 5 in. [127 mm] outside diameter, with minimum wall from about 0.015 to 0.500 in. [0.4 to 12.7 mm]; tubing with other diameters may be furnished when all other requirements of the specification are met. State on the purchase order whether wall is minimum or average, because that choice changes how the mill interprets tolerance and how the designer reads remaining wall after fabrication.

Outside-diameter and wall variations follow ASTM A1016/A1016M as invoked by A213, with cold-finished and hot-finished routes carrying different practical bands. Cold-finished tubes commonly hold tighter OD control; hot-finished tubes allow wider OD and wall windows. Permissible variations from a specified average wall for cold-finished tube are often summarized as ±10% of the specified average wall, while minimum-wall product is accepted to the A1016 minimum-wall tables rather than a symmetric ± window. Confirm the exact A1016 rows for the OD and finish route on the ordered edition — and remember Footnote D when the OD × wall is small enough that many drawing passes push the carbon path to 0.040% max.

Item Typical A213 TP316L dimensional practice
Product form Seamless only (cold-finished or hot-finished)
Usual size band ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD; wall ~0.015–0.500 in. [0.4–12.7 mm] min (or average wall if PO says so)
Wall basis Minimum wall (default commercial practice) or average wall when specified
OD / wall tolerances Per ASTM A1016/A1016M for the finish route and size; cold-finished average wall often ±10%
Length Cut lengths for HX / condenser / boiler bundles, or mill random lengths by agreement
Secondary size note ASME B36.19 schedules may appear only when a buyer asks for a pipe-schedule cross-reference — not as the primary A213 size callout

Put the cut list, U-bend or straight-tube preference, and end preparation on the enquiry so mill and stock lengths can be mixed efficiently. Minimum wall is a first-class A213 concept: if the datasheet assumes average wall, say so explicitly before the heat is rolled.

Equivalent Grades

Equivalence language around TP316L tube is often looser than a chloride-service, as-welded exchanger purchase order can afford. ASTM A213 Grade TP316L / UNS S31603 is the governing designation for this article; EN 1.4404 / 1.4432 and JIS SUS316L are approximate wrought names that point to similar low-carbon Mo-bearing chemistry families but are not automatic substitutes on an A213 mill test certificate. When a datasheet says “equivalent to 316L,” confirm which product standard, tensile/hardness table, and heat-treatment clause the mill will actually certify.

Designation Notes
ASTM A213 / A213M Grade TP316L Governing ASTM seamless boiler / HX tube product standard for this article
UNS S31603 Unified number listed in the stainless chemistry table
ASME SA-213 TP316L Separate ASME Code Book adoption of the A213 grade text — dual-mark only when the PO asks
EN 1.4404 / 1.4432 Approximate wrought low-carbon Mo-bearing designations; order EN tube forms under the relevant EN tube specs
JIS SUS316L Approximate Japanese grade name; confirm the Japanese tube product standard when ordering JIS product
Related plate A240 / SA240 flat product in the same UNS family — order plate and tube under their own product standards

ASME SA-213 TP316L is the separate Code Book adoption of the same grade text; dual A213/SA-213 marking is a purchase-order option, not a claim that the two standards are one document. Compare standard-carbon Mo, H-grade, and higher-Mo sisters on their own ASTM A213 pages before swapping grades in a tube bundle.

Heat Treatment and Delivery Condition

TP316L under ASTM A213 is furnished solution treated at a minimum of 1900 °F [1040 °C], then quenched in water or cooled rapidly by other means at a rate sufficient to prevent carbide reprecipitation. That heat-treatment row applies to both cold-finished and hot-finished seamless tube. Low carbon plus molybdenum reduce sensitization and pitting risk, but they do not replace the solution anneal — under-cooling or skipping the quench can still leave a structure that fails a contractual A262 capability check even when ladle chemistry looked acceptable on paper.

Cold-finished versus hot-finished is a process and dimensional route, not a substitute for the anneal: cold-finished tube is typically drawn after hot working and then solution treated; hot-finished tube may be quenched after hot forming when the edition allows and finishing temperature is not below the minimum anneal. Delivery condition for SHH STEEL TP316L is solution annealed and pickled (or bright annealed by agreement), with heat-treatment temperature and quench method stated on the EN 10204 3.1 certificate. Straightening, cutting, and end finishing follow heat treatment.

When Supplementary Requirement language for intergranular-corrosion capability (commonly tied to ASTM A262 Practice E on sensitized specimens for low-carbon types; applicability of sensitizing treatment for Mo ≥3% grades may be negotiable per edition notes) is ordered, the corrosion test report travels with the heat-treatment record. H-grade grain-size rules do not rewrite the TP316L path — use A213 TP316H when the datasheet calls for H-grade carbon and grain-size controls.

Corrosion Resistance

TP316L combines the two corrosion levers buyers ask for most often on chloride-service exchangers: molybdenum for pitting and crevice resistance relative to TP304L, and low carbon for as-welded intergranular resistance relative to standard TP316. That pairing makes TP316L the default Mo-bearing seamless tube grade for coastal condensers, chloride-leaning process HX, and many food or pharmaceutical utility exchangers where tube-to-tubesheet joints remain as-welded. It is still not a duplex or superaustenitic substitute — severe seawater, high-temperature chlorides, and under-deposit attack may need A213 TP317L or A213 UNS S31254.

ASTM A213 itself does not publish a corrosion-rate or PREN table for TP316L; selection remains engineering judgment against fluid, temperature, velocity, and inspection philosophy inside the boiler or exchanger. When a specification calls for ASTM A262 Practice E, write that Supplementary Requirement onto the purchase order so the test is contractual rather than assumed from a verbal “full certs” note. SHH STEEL will not rank TP316L as equal to superaustenitic grades in severe chlorides — that claim is not supported by the product standard.

Applications of A213 TP316L Tube

TP316L is ordered when the exchanger needs both molybdenum and low-carbon documentation under A213 — typically as-welded tube-to-tubesheet joints in chloride-leaning cooling water or process service. The table below pairs typical application areas with a selection note so the grade is chosen for the fluid and welding sequence — not only for the familiar “316L” name on the BOM.

Application area Typical use of TP316L tube Selection note
Cooling-water / coastal condensers Seamless condenser tubes with as-welded or fabricated tube-to-tubesheet joints in chloride-leaning water Confirm chloride level and cleaning chemistry; step up PREN if needed
Process heat exchangers Straight and U-bend HX tubes needing Mo + L-grade IGC resistance State min vs average wall, BWG, bend radius, and any A262 SR on the enquiry
Food / pharmaceutical utilities Utility and process HX where low-carbon 316 stainless tube is accepted Follow hygiene finish and welding procedure requirements
Chemical and refining Tube-side or shell-side circuits with mild-to-moderate chlorides and welded attachments Prefer TP317L or S31254 for severe chloride loops
Boiler / moderate-temperature steam Seamless utility steam tubing where L-grade Mo chemistry is preferred For creep-critical H-grade service open TP316H; L-grade is not an H substitute
Dual-certified tube duty Heats marked TP316/TP316L when both Table 4 rows and carbon rules are cleared Ask for dual marking on the PO — do not assume from PMI alone

For low-chloride oxidizing service without Mo, open A213 TP304L; for standard-carbon Mo service without as-welded IGC concern, open A213 TP316; for higher PREN needs stay on the A213/A213M hub and move to TP317L or S31254.

Weldability

TP316L tube is chosen because it welds cleanly for tube-to-tubesheet joints while keeping base-metal carbon low and molybdenum present in both the tube and the matching filler. Common practice uses ER316L (or equivalent covered electrodes) under a qualified WPS so the weld metal carbon and molybdenum stay aligned with the L-grade Mo-bearing base tube. Heat input control, interpass limits, and post-weld cleaning remain the fabricator’s responsibility under the applicable boiler or pressure-vessel code — A213 governs the seamless tube product, not the field or shop weld procedure.

Because A213 TP316L is seamless, there is no mill longitudinal weld to radiograph the way welded pipe standards describe. Focus inspection language on tube integrity (hydro or NDE of each length), tube-to-tubesheet joint quality, and any contractual corrosion test on the base metal. Specify end preparation and surface finish on the tube PO when orbital or clean-service joins are planned. If PREN requirements exceed standard 316L after welding, changing the base metal to A213 TP317L or A213 UNS S31254 is usually a better move than relying on filler selection alone.

Surface Finishes

Standard mill delivery for ASTM A213 TP316L is solution annealed and pickled, leaving a clean matte finish suitable for most condenser, process, and utility heat-exchanger tube duty. Bright annealing under protective atmosphere produces a smoother reflective surface used on some clean-process and instrumentation tube lines and must be called out because it changes the heat-treatment route. Light polish or specified Ra on the bore or OD is a commercial or service-center operation on top of A213 product, not automatic with the grade stamp.

When a hygienic or fouling-sensitive exchanger specification quotes an Ra maximum on the bore, put it on the tube purchase order with its own acceptance language and sampling plan. SHH STEEL stencils grade and heat treatment as standard requirements; polish, special OD grind, and passivation after fabrication remain commercial extras unless the contract says otherwise. End preparation (plain, slightly beveled, or as needed for tube expanding) should be ordered together with finish so receiving inspection shares one acceptance language.

Inspection and Testing

Base ASTM A213 testing for TP316L includes heat analysis (carbon against the 0.035% / Footnote D ceiling and molybdenum inside 2.00–3.00%), tension tests to the Table 4 70/25 ksi floors, hardness tests to the Table 4 maximum, flattening and flaring tests on a lot basis, and either hydrostatic testing or nondestructive electric testing of each length. The manufacturer may choose hydro versus NDE unless the purchase order fixes the method; both are acceptance routes inside the product standard, not informal upgrades. Marking includes the ASTM designation, grade, size, heat number, and other clause-required data so receiving inspection can tie each length back to the MTC.

Supplementary Requirements commonly added on TP316L tube orders are summarized below. Invoke them by number or clear purchase-order wording; mills will not assume product analysis or intergranular-corrosion testing from a verbal “full certs” note.

Option Purpose
Product analysis Confirms chemistry — including C and Mo — on finished tube (via A1016 / PO language)
Intergranular corrosion A262 Practice E on sensitized specimens (low-carbon types) as a contractual Supplementary Requirement
Minimum vs average wall States which wall basis the size callout uses
Fixed hydro or NDE method Removes manufacturer’s option when the end user mandates one route
Third-party inspection / EN 10204 3.2 Witnessed testing and certificate when the project requires it
Dual TP316/TP316L marking When ladle carbon and both Table 4 rows support dual certification

Lot definitions for continuous heat treatment or direct quench after hot forming follow the size-based lot sizes in A213; ask the mill to state lot identity clearly on the certificate so hardness and tension specimens map cleanly to the bundle you receive.

Packaging and Shipping

TP316L tube leaves SHH STEEL bundled, capped or end-protected, and tagged for export or domestic delivery according to the length mix and bend form on the order. Bundle tags repeat the ASTM A213 grade, OD × wall (or BWG), heat number, and PO reference so site receiving can check the shipment without opening every certificate packet first. U-bent tubes need extra cradle or case protection so bend radii and legs are not distorted in transit.

Export packing can be bare bundles, wrapped bundles, or wooden-cased lengths for bright-annealed, polished, or small-bore material. We ship under the Incoterms on the order acknowledgement — FOB, CFR, CIF, EXW, or other agreed terms. Inland trucking, bilingual destination marks, or project color coding for bundle tags should be stated on the enquiry beside the metallurgical notes.

Why Choose SHH STEEL

SHH STEEL treats ASTM A213 TP316L as a product standard with enforceable low-carbon and molybdenum chemistry, tensile, hardness, heat-treatment, and marking rules — not as a catalogue nickname for “any 316L tube.” The MTC reports ladle carbon against the 0.035% (or Footnote D 0.040%) ceiling, molybdenum inside 2.00–3.00%, and the Table 4 70/25 ksi tensile/hardness set; the stencil carries seamless tube identity under A213; and dual A213/SA-213 marking is offered only when requested so Code and non-Code jobs stay cleanly documented.

We keep the 316-family conversation honest for chloride and as-welded HX duty. If standard-carbon Mo tensile floors are required and as-welded IGC is not the driver, we open A213 TP316. If creep-range boiler service needs H-grade carbon and grain-size controls, we open A213 TP316H. If chlorides are mild enough that molybdenum is not justified but low carbon still is, we open A213 TP304L. The A213/A213M hub is organized the same way — grade by grade under ASTM, seamless tube only.

Lead times combine near-term stock lengths with mill schedules; we say which is which on the quotation. Cut-to-length, U-bending, polish, and third-party inspection are defined extras. The tube that arrives should match the ASTM callout the engineer wrote, with paperwork a third-party inspector can read without translation.

Supply Capability

SHH STEEL can supply ASTM A213 TP316L stainless steel tube against the edition and finish route named on your enquiry. The capability table below summarizes the sizes, finishes, and documents we regularly quote for this low-carbon molybdenum grade, followed by the Stock / Available sizes map buyers ask for when they need a quick sense of what to enquire against for condenser and as-welded heat-exchanger duty.

Item SHH STEEL capability for TP316L
Standard ASTM A213 / A213M (dual SA-213 marking on request) Grade TP316L / UNS S31603
Product form Seamless only — cold-finished and hot-finished
Size Typical OD × min wall (or average wall) in the A213 usual band; other diameters by agreement
Wall / gauge Minimum wall or average wall; BWG / gauge callouts accepted on enquiry
Length Cut-to-length for HX / condenser / boiler bundles; mill random by agreement; U-bends on enquiry
Finish Annealed and pickled; bright annealed or light polish by agreement
Testing Tension (70/25 ksi), hardness (max 192 HBW / 90 HRB), flattening, flaring, hydro or NDE per length; full ladle chemistry including C and Mo on MTC; product analysis / IGC on order
Documents EN 10204 3.1 with full ladle chemistry; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Stock / Available sizes

SHH STEEL quotes TP316L tube against a practical stock-and-mill enquiry range rather than a frozen warehouse SKU list. The sizes below are the OD × wall / BWG combinations buyers most often request for as-welded chloride-service condensers and process exchangers; availability of any single line on a given week depends on mill drawing and our inbound schedule, so treat the table as a supply map for enquiry — not a guarantee that every line sits on the floor with a published tonnage.

Item Typical stock / enquiry range for TP316L
Outside diameter 12.7, 15.88, 19.05, 25.4, 31.8, 38.1, 50.8, 63.5, 76.2 mm (and other HX/condenser ODs on enquiry; up through the usual A213 ~5 in. [127 mm] band)
Wall / BWG BWG 10–20 class walls and metric min-wall equivalents; lighter and heavier walls by agreement
Common OD × wall examples 19.05 × 1.65 mm; 19.05 × 2.11 mm; 25.4 × 2.11 mm; 25.4 × 2.77 mm; 31.8 × 2.77 mm; 38.1 × 2.77 mm; 50.8 × 2.77 mm — illustrative condenser/HX sizes, confirm min vs average wall
Length Cut lengths for exchanger and condenser bundles; U-bends and straight random lengths on enquiry
Special Non-standard OD/wall, bright anneal, polished bore, dual TP316/TP316L, and dual A213/SA-213 marking — confirm on enquiry before the heat is reserved

When you send an enquiry, list OD × wall (or BWG), wall basis (minimum or average), cold-finished or hot-finished preference, quantity or cut list, required marking (A213 alone, dual A213/SA-213, and/or dual TP316/TP316L), and any Supplementary Requirements including A262. We reply with what we can ship from near-term stock versus what needs a mill run, without inventing fake warehouse codes or tonnage claims.

Send the size list, finish route, quantity or cut lengths, required marking, Supplementary Requirements, and destination on one enquiry. We will confirm carbon, molybdenum, and the 70/25 ksi tensile/hardness set against the ordered edition, state what ships from near-term availability versus mill production, and keep the offer aligned with the ASTM A213 / A213M product standard that governs this page. Related grades such as A213 TP317L, A213 UNS S31254, and A213 TP304L sit on the same hub when the datasheet steps beyond low-carbon 316.

FAQ

Is ASTM A213 the same as ASME SA-213 for TP316L?
No. ASTM A213 / A213M is the ASTM International product specification for seamless boiler, superheater, and heat-exchanger tubes; ASME SA-213 / SA-213M is the separate ASME Code Book adoption of that grade text. Chemistry, tensile, and hardness floors align closely for a given referenced edition, but they remain two independent standards. Dual-mark A213/SA-213 tube only when the purchase order asks for both names on the stencil and MTC.
Does ASTM A213 TP316L include welded or HCW tube?
No. ASTM A213 covers seamless tube only. There is no WLD or HCW manufacturing type under this product standard the way ASTM A312 describes pipe. The process choice for TP316L under A213 is cold-finished versus hot-finished seamless tube, plus the heat-treatment and testing clauses of the ordered edition. If you need welded stainless pipe, that is a different product standard and a different steelspecs page family.
What does Footnote D mean for TP316L carbon under A213?
Footnote D states that for small diameter or thin walls, or both, where many drawing passes are required, a carbon maximum of 0.040% is necessary in Grades TP304L, TP304LN, TP316L, and TP316LN. The default melt ceiling remains 0.035%. Put the OD × wall and whether Footnote D applies on the enquiry so the mill selects a heat that matches the path you are buying, and confirm the footnote text on the ordered edition.
Minimum wall vs average wall — which should I order for A213 TP316L?
Order minimum wall when the design and datasheet are written around a guaranteed minimum thickness after tolerance. Order average wall only when the purchase order explicitly allows average-wall product and the designer has accepted that basis. The two readings produce different tube from the same OD × wall line, so put the wall basis on the enquiry before the mill selects tooling and tolerance tables from A1016.
Hydrostatic test vs NDE — which do I get on TP316L tube?
ASTM A213 requires each tube to be hydrostatically tested or nondestructively electrically tested. The manufacturer may choose the method unless the purchase order fixes one. Neither route is an informal upgrade over the other inside the product standard. State the preferred method on the enquiry if your end user or inspector mandates hydro only or a named NDE technique.
Does A213 Table 4 set a hardness limit for TP316L?
Yes. Table 4 for TP316L lists tensile strength 70 ksi, yield strength 25 ksi, elongation 35%, and a hardness maximum of 192 HBW / 200 HV or 90 HRB. Hardness tests are part of lot acceptance under A213, which differs from many A312 pipe rows for the same UNS number that omit a Table 4 hardness cap. If a project needs a tighter hardness window than Table 4, write it into the purchase order as an additional requirement.
What is the UNS number and chemistry of ASTM A213 TP316L?
TP316L is UNS S31603. Melting limits include carbon ≤0.035% (Footnote D to 0.040% on small-OD / light-wall), manganese ≤2.00%, phosphorus ≤0.045%, sulfur ≤0.030%, silicon ≤1.00%, chromium 16.0–18.0%, nickel 10.0–14.0%, and molybdenum 2.00–3.00%, with nitrogen as a no-requirement ellipsis in the public table excerpts used here. Both the carbon ceiling and the Mo window must appear on the MTC to clear the grade.
TP316 vs TP316L — which A213 tube should I order?
Order TP316 when the specification calls for the standard 75/30 ksi tensile floor, molybdenum 2.00–3.00%, and carbon ≤0.08% is acceptable. Order TP316L when as-welded intergranular resistance is also required and the lower 70/25 ksi floor is acceptable. Dual TP316/TP316L certification is possible on qualifying heats — ask for it on the PO rather than assuming it from a PMI gun reading.
TP304L vs TP316L — when do I need molybdenum under A213?
Order TP316L when chloride pitting or crevice corrosion dominates the cooling water or process fluid and you still need low-carbon as-welded resistance. TP304L remains appropriate for many oxidizing and low-chloride steam and process services where molybdenum is not justified. ASTM A213 does not publish a chloride ranking table; open the TP316L tube page when chlorides drive the selection, and step further to TP317L or S31254 when PREN exceeds standard 316L.
TP316L vs TP316H — can L-grade replace H-grade boiler tube?
No. TP316H carries the H-grade carbon range, grain-size controls, and creep-rupture framing that creep-critical boiler and superheater datasheets expect. TP316L is the low-carbon, Mo-bearing, as-welded IGC grade with a 70/25 ksi tensile floor. Do not treat "316L" as a synonym stamp for H-grade service on the MTC, and do not stretch L-grade into creep-range framing without a design review.
What heat treatment does ASTM A213 require for TP316L?
TP316L is solution treated at a minimum of 1900 °F [1040 °C] and then water quenched or rapidly cooled to prevent carbide reprecipitation. Both cold-finished and hot-finished seamless tube follow that heat-treatment requirement. Ask the mill to state anneal temperature and quench method on the EN 10204 3.1 certificate so receiving inspection can clear the heat without chasing verbal confirmations.
Can you dual-certify ASTM A213 and ASME SA-213 TP316L, or TP316/TP316L?
Yes on both axes when the heat and testing support it. Dual A213/SA-213 marking is available when the purchase order requests both independent standards on the stencil and MTC. Dual TP316/TP316L is available when ladle chemistry meets the tighter carbon rules and tensile plus hardness results clear both Table 4 rows. Spell the required marking on the enquiry so the heat is selected correctly.

Conclusion

ASTM A213 TP316L / UNS S31603 is the low-carbon molybdenum-bearing seamless stainless steel tube grade for boiler, superheater, and heat-exchanger service when chloride resistance and as-welded intergranular resistance are both required. SHH STEEL supplies cold-finished and hot-finished seamless tube in the usual OD × wall / BWG band, solution annealed, tested to the Table 4 70/25 ksi tensile and hardness limits, and documented on EN 10204 3.1 certificates — with dual SA-213 marking only when the order asks for that separate ASME standard. For sister grades and stock-oriented size discussions, start from the A213/A213M hub, then send your OD × wall list, wall basis, Footnote D applicability, and marking requirements so we can align mill and near-term availability to the ASTM callout.

Contact: admin@steelspecs.com

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X