ASTM A213 TP304LN Stainless Steel Tube
What is ASTM A213 TP304LN Stainless Steel Tube
ASTM A213 / A213M is the product specification for seamless ferritic and austenitic alloy-steel boiler, superheater, and heat-exchanger tubes. Grade TP304LN sits at the intersection of two design needs that often conflict on a single datasheet: low carbon for as-welded intergranular resistance, and nitrogen for recoverable tensile strength. Listed under UNS S30453, it carries C ≤0.035% on the melt (Footnote D raises that ceiling to 0.040% for small-diameter or thin-wall tube that needs many drawing passes), a mandatory nitrogen band of 0.10–0.16%, chromium 18.0–20.0%, and nickel 8.0–11.0%. The nitrogen floor brings Table 4 tensile acceptance back to 75 ksi [515 MPa] / 30 ksi [205 MPa] — the TP304 pair — instead of the lower 70/25 ksi floor that plain TP304L accepts.
SHH STEEL can supply ASTM A213 TP304LN stainless steel tube as seamless cold-finished and hot-finished product in the usual boiler and heat-exchanger OD × wall / BWG band, shipped with EN 10204 3.1 mill test certificates that report the full stainless-table ladle chemistry — carbon and nitrogen both visible — and the Table 4 tensile and hardness results. Dual A213 / SA-213 marking is offered only when the purchase order asks for both independent standards. Start from the A213/A213M hub for the rest of the 304-family tube grades.
Commercial shorthand such as 304LN, S30453, or “low-carbon nitrogen 304 HX tube” never replaces the ASTM grade on the MTC or stencil. Sister grades under the same ASTM standard include A213 TP304L, A213 TP304N, A213 TP304, A213 TP316LN, and A213 TP304H. A213 covers seamless tube only — there is no welded or HCW manufacturing type — so cold-finished versus hot-finished seamless route is the finish/process choice.
Chemical Composition of A213 TP304LN
Two chemistry layers matter for TP304LN under ASTM A213. Melting analysis is mandatory for every heat; product analysis on finished tube applies only when Supplementary Requirement wording or the purchase order invokes it through ASTM A1016/A1016M, with tolerances typically from ASTM A480/A480M Table A1.1. Nitrogen analysis method is a matter of agreement (Footnote B). Footnote D is contractual language for this grade: for small diameter or thin walls requiring many drawing passes, a carbon maximum of 0.040% is necessary — confirm the OD/wall trigger on the ordered edition rather than guessing from a catalogue note.
The tables below reproduce the melt limits for TP304LN / UNS S30453 and the product-analysis limits from A480 Table A1.1 tolerances. Values are maximum unless a range is shown.
Melting analysis (heat / ladle analysis)
| Element | TP304LN (UNS S30453) melting analysis |
|---|---|
| Carbon (C) | ≤ 0.035 (Footnote D: ≤ 0.040 for small OD / thin wall with many drawing passes) |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 18.0 – 20.0 |
| Nickel (Ni) | 8.0 – 11.0 |
| Molybdenum (Mo) | … (no requirement) |
| Nitrogen (N) | 0.10 – 0.16 |
Source: ASTM A213/A213M stainless chemistry table for Grade TP304LN / UNS S30453 (public mill / specification PDF excerpt). Confirm the ordered edition on the purchase order. Note the nickel band is 8.0–11.0% under A213 for TP304LN — the same as TP304N — not the wider 8.0–12.0% band used for TP304L under the same table; do not copy an A312 pipe Ni window onto an A213 tube certificate.
Product analysis — A480/A480M Table A1.1 tolerances applied
| Element | Melting | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.035 | 0.01 over | ≤ 0.045 |
| Manganese (Mn) | ≤ 2.00 | 0.04 over | ≤ 2.04 |
| Phosphorus (P) | ≤ 0.045 | 0.010 over | ≤ 0.055 |
| Sulfur (S) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Silicon (Si) | ≤ 1.00 | 0.05 over | ≤ 1.05 |
| Chromium (Cr) | 18.0 – 20.0 | 0.20 under / over | 17.80 – 20.20 |
| Nickel (Ni) | 8.0 – 11.0 | 0.10 under / 0.15 over | 7.90 – 11.15 |
| Nitrogen (N) | 0.10 – 0.16 | 0.01 under / 0.02 over | 0.09 – 0.18 |
Read carbon and nitrogen together. Holding C ≤0.035% (or ≤0.040% under Footnote D) reduces chromium-carbide precipitation at grain boundaries during welding or slow cooling through the sensitizing range — the reason exchanger fabricators specify LN tube for as-welded tube-to-tubesheet service. The 0.10–0.16% nitrogen band then restores tensile capacity so the designer does not have to accept TP304L’s lower 70/25 ksi floor. Versus A213 TP304N, the only intentional chemistry change is the L-grade carbon ceiling; versus A213 TP304L, the intentional additions are the nitrogen band and the higher Table 4 pair.
When product analysis is ordered, finished tube may read up to C 0.045%, Mn 2.04%, P 0.055%, S 0.035%, and Si 1.05%, with Cr 17.80–20.20%, Ni 7.90–11.15%, and N 0.09–0.18%. Those are the only product limits we quote from the A480 A1.1 path. Put any tighter project carbon or nitrogen ceiling on the purchase order before the heat is selected.
Mechanical Properties of A213 TP304LN
ASTM A213 Table 4 sets the tensile acceptance floor for TP304LN at 75 ksi [515 MPa] tensile strength and 30 ksi [205 MPa] yield strength (0.2% offset), with elongation of 35% minimum in 2 in. or 50 mm and hardness max 192 HBW / 200 HV or 90 HRB. That is the same tensile/yield pair as TP304 and TP304N’s hardness ceiling — and five / five ksi above TP304L’s 70/25 ksi floor. Nitrogen is doing the strength recovery work that low carbon would otherwise give away.
| Property | TP304LN requirement (Table 4) |
|---|---|
| Tensile strength, min | 75 ksi [515 MPa] |
| Yield strength (0.2% offset), min | 30 ksi [205 MPa] |
| Elongation in 2 in. or 50 mm, min | 35% |
| Hardness, max | 192 HBW / 200 HV or 90 HRB |
Source: ASTM A213/A213M Table 4 for TP304LN / UNS S30453 (public specification PDF excerpt). Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or thinner than 0.015 in. [0.4 mm] wall. Flattening and flaring tests are also required on a lot basis.
Designers who assumed they must accept TP304L’s lower tensile floor to get L-grade carbon should re-check whether TP304LN’s 75/30 ksi pair is available for the same fluid and weld sequence. Do not assume a TP304L certificate clears TP304LN — nitrogen must be present and reported. When molybdenum is also required with low carbon and nitrogen, open A213 TP316LN.
Dimensions and Tolerances
Dimensional supply for ASTM A213 TP304LN is tube language — OD × wall (minimum or average) and commercially BWG / gauge — not ASME B36.19 pipe schedules as the primary size story. Usual A213 sizes run from about 1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD, with minimum wall about 0.015–0.500 in. [0.4–12.7 mm]; other diameters may be furnished when all other requirements are met. Footnote D’s carbon relief for small OD / thin wall with many drawing passes is a chemistry accommodation, not a free pass on dimensional tolerance — still state min versus average wall on the PO.
OD and wall variations follow ASTM A1016/A1016M as invoked by A213. Cold-finished tubes commonly hold tighter OD control; hot-finished tubes allow wider windows. Cold-finished average-wall product is often summarized as ±10% of the specified average wall; minimum-wall product follows the A1016 minimum-wall tables. Confirm the exact rows for the OD and finish route on the ordered edition.
| Item | Typical A213 TP304LN dimensional practice |
|---|---|
| Product form | Seamless only (cold-finished or hot-finished) |
| Usual size band | ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD; wall ~0.015–0.500 in. [0.4–12.7 mm] min (or average wall if PO says so) |
| Wall basis | Minimum wall (default commercial practice) or average wall when specified |
| OD / wall tolerances | Per ASTM A1016/A1016M for the finish route and size |
| Length | Cut lengths for HX / boiler bundles, or mill random lengths by agreement |
| Footnote D note | Small OD / thin wall with many draws may use C max 0.040% — chemistry, not a size exemption |
Put the cut list, U-bend preference, and end preparation on the enquiry. Minimum wall remains a first-class A213 concept regardless of L/N chemistry.
Equivalent Grades
Equivalence talk around low-carbon nitrogen 304 tube needs more discipline than a casual “same as 304L with N” remark. ASTM A213 Grade TP304LN / UNS S30453 is the governing designation here; EN 1.4311 and related wrought names point to similar families but are not automatic substitutes on an A213 MTC. Confirm product standard, tensile table, and heat-treatment clause before accepting an “equivalent” stamp.
| Designation | Notes |
|---|---|
| ASTM A213 / A213M Grade TP304LN | Governing ASTM seamless boiler / HX tube product standard for this article |
| UNS S30453 | Unified number in the stainless chemistry table |
| ASME SA-213 TP304LN | Separate ASME Code Book adoption — dual-mark only when the PO asks |
| EN 1.4311 (approx.) | Approximate wrought designation; order EN tube under the relevant EN tube specs |
| Related plate | A240 / SA240 flat product in the same UNS family |
Dual A213/SA-213 marking is a purchase-order option, not a claim that the two standards are one document. Compare A213 TP304L and A213 TP304N on their own pages before swapping LN for L or N inside a bundle.
Heat Treatment and Delivery Condition
TP304LN under ASTM A213 is furnished solution treated at a minimum of 1900 °F [1040 °C], then quenched in water or cooled rapidly by other means. That Table 3 heat-treatment row applies to both cold-finished and hot-finished seamless tube. Low carbon reduces sensitization risk after welding, but it does not excuse a skipped or under-cooled solution treatment at the mill — nitrogen still needs to stay in solid solution for the tensile floor to be meaningful.
Cold-finished versus hot-finished is a process and dimensional route, not a substitute for the anneal. Delivery condition for SHH STEEL TP304LN is solution annealed and pickled (or bright annealed by agreement), with anneal temperature and quench method on the EN 10204 3.1 certificate. Straightening, cutting, and end finishing follow heat treatment.
When A262 Practice E or another intergranular-corrosion Supplementary Requirement is ordered, the corrosion test report travels with the heat-treatment record. H-grade grain-size rules belong to A213 TP304H, not to the LN path.
Corrosion Resistance
TP304LN is specified first for intergranular-corrosion resistance in the as-welded condition, not for a step-change in general corrosion relative to other 18-8 grades. Low carbon limits chromium-carbide networks at grain boundaries after tube-to-tubesheet welding or after sensitizing thermal cycles; nitrogen does not undo that benefit when the carbon ceiling is held. The passive film still behaves like other 18-8 austenitics in oxidizing and low-chloride media.
In chloride-bearing waters and brine-leaning exchangers, pitting and crevice attack remain limiting, and buyers usually step to A213 TP316LN or A213 TP316L. ASTM A213 does not publish a corrosion-rate table for TP304LN; when A262 Practice E is required, write it onto the purchase order so the test is contractual.
Applications of A213 TP304LN Tube
TP304LN earns its place wherever the exchanger fabricator wants L-grade as-welded IGC resistance without surrendering the 75/30 ksi tensile pair. Typical homes are tube-to-tubesheet joints left as-welded, process HX with oxidizing media, and utility exchangers where design stress assumes TP304-class tensile numbers.
| Application area | Typical use of TP304LN tube | Selection note |
|---|---|---|
| As-welded tube-to-tubesheet HX | Low-C base metal with nitrogen-supported tensile floor | Confirm Footnote D if many draws on small OD/thin wall |
| Process / chemical exchangers | Oxidizing or mild corrosive media needing IGC-conscious tube | Step to Mo grades if chlorides dominate |
| Utility / power HX | Where design uses 75/30 ksi but L-grade carbon is specified | Do not substitute TP304L paperwork for LN nitrogen |
| Food / pharma utilities | Utility HX where low-carbon 304-family tube is accepted | Follow hygiene finish and welding procedure requirements |
| Creep-critical boiler tubing | Usually not the first LN use case | Open TP304H or S30432 for H-grade / USC framing |
Stay on the A213/A213M hub for sister L, N, and Mo grades rather than mixing A312 pipe certificates into tube acceptance.
Weldability
TP304LN is often chosen specifically because tube-to-tubesheet and attachment welds will enter service without a full solution anneal of the joint. Matching or near-matching austenitic filler (commonly ER308L) under a qualified WPS is typical; some fabricators discuss nitrogen-bearing deposits when base-metal N must be reflected, but that decision sits in the WPS, not in A213. Heat input, interpass, and cleaning remain the fabricator’s code responsibility.
A213 TP304LN is seamless — no mill longitudinal weld to radiograph as welded-pipe standards describe. Focus inspection on each-length hydro or NDE, joint quality, and any contractual IGC test on the base metal. When chlorides plus as-welded IGC both matter, many owners move the base metal to A213 TP316LN rather than asking plain LN 18-8 to do molybdenum’s job.
Surface Finishes
Standard mill delivery for ASTM A213 TP304LN is solution annealed and pickled. Bright annealing under protective atmosphere is a called-out route for cleaner reflective surfaces. Specified Ra on bore or OD, light polish, and post-fabrication passivation are commercial extras on top of the A213 product stamp, not automatic with the grade.
Hygiene or fouling-sensitive exchanger specs that quote an Ra maximum should put that limit on the tube PO with its own sampling plan. End preparation (plain, slightly beveled, or expander-ready) should be ordered with finish so receiving inspection shares one language.
Inspection and Testing
Base ASTM A213 testing for TP304LN includes heat analysis (carbon and nitrogen both reported), tension to the Table 4 75/30 ksi floors, hardness to the Table 4 maximum, flattening and flaring on a lot basis, and hydro or NDE of each length. The manufacturer may choose hydro versus NDE unless the PO fixes the method. Marking carries ASTM designation, grade, size, heat number, and other clause-required data.
| Option | Purpose |
|---|---|
| Product analysis | Confirms C and N on finished tube |
| Agreed nitrogen analysis method | Locks Footnote B method |
| Intergranular corrosion (A262 Practice E) | Contractual Supplementary Requirement for as-welded IGC confidence |
| Footnote D carbon note | Clarifies when C max 0.040% applies for small OD / thin wall |
| Minimum vs average wall | States wall basis on the size callout |
| Fixed hydro or NDE / EN 10204 3.2 | Removes manufacturer option / adds witnessed testing |
Ask the mill to map lot identity clearly so carbon, nitrogen, tension, and hardness specimens all point to the same bundle.
Packaging and Shipping
TP304LN tube leaves SHH STEEL bundled, end-protected, and tagged with ASTM A213 grade, OD × wall (or BWG), heat number, and PO reference. U-bent tubes need cradle or case protection so bend radii and legs survive transit. Export packing ranges from bare or wrapped bundles to wooden cases for bright-annealed or small-bore material.
We ship under the Incoterms on the order acknowledgement — FOB, CFR, CIF, EXW, or other agreed terms. Bilingual marks, inland trucking, and project color coding belong on the enquiry beside the metallurgical notes, not as afterthoughts at dispatch.
Why Choose SHH STEEL
SHH STEEL treats ASTM A213 TP304LN as the grade that joins an L-grade carbon ceiling to a nitrogen-supported 75/30 ksi floor — not as a casual relabel of TP304L. The MTC shows both carbon and nitrogen, the Table 4 tensile/hardness set, and seamless A213 identity; dual A213/SA-213 marking appears only when requested.
If the datasheet only needs low carbon and can accept 70/25 ksi, we open A213 TP304L. If it needs 80/35 ksi and can accept standard carbon, we open A213 TP304N. If chlorides dominate, we open A213 TP316LN / A213 TP316L. The A213/A213M hub keeps those choices grade by grade under ASTM, seamless tube only.
Lead times mix near-term stock with mill schedules; cut-to-length, U-bending, polish, and third-party inspection are defined extras. The tube on site should match the callout the engineer wrote.
Supply Capability
SHH STEEL can supply ASTM A213 TP304LN stainless steel tube against the edition and finish route on your enquiry. The capability table and Stock / Available sizes map below are the practical enquiry frame for this low-carbon nitrogen grade.
| Item | SHH STEEL capability for TP304LN |
|---|---|
| Standard | ASTM A213 / A213M (dual SA-213 marking on request) Grade TP304LN / UNS S30453 |
| Product form | Seamless only — cold-finished and hot-finished |
| Size | Typical OD × min wall (or average wall) in the A213 usual band; other diameters by agreement |
| Wall / gauge | Minimum wall or average wall; BWG / gauge callouts accepted |
| Length | Cut-to-length for HX / boiler bundles; mill random by agreement; U-bends on enquiry |
| Finish | Annealed and pickled; bright annealed or light polish by agreement |
| Testing | Tension (75/30 ksi), hardness (max 192 HBW / 90 HRB), flattening, flaring, hydro or NDE; full melt chemistry including C and N; product analysis / IGC on order |
| Documents | EN 10204 3.1; third-party inspection / 3.2 on request |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
Stock / Available sizes
SHH STEEL quotes TP304LN against a stock-and-mill enquiry range, not a frozen SKU/tonnage list. Representative OD × wall / BWG combinations for L/N heat-exchanger and boiler tube appear below; weekly availability depends on mill drawing and inbound schedule.
| Item | Typical stock / enquiry range for TP304LN |
|---|---|
| Outside diameter | 12.7, 15.88, 19.05, 25.4, 31.8, 38.1, 50.8, 63.5 mm (and other HX ODs on enquiry; through the usual A213 ~5 in. [127 mm] band) |
| Wall / BWG | BWG 12–20 class walls and metric min-wall equivalents; Footnote D sizes called out when many draws apply |
| Common OD × wall examples | 15.88 × 1.65 mm; 19.05 × 1.65 mm; 19.05 × 2.11 mm; 25.4 × 2.11 mm; 25.4 × 2.77 mm; 31.8 × 2.77 mm — illustrative, confirm min vs average wall |
| Length | Cut lengths for exchanger bundles; U-bends and straight random on enquiry |
| Special | Bright anneal, polished bore, A262 Practice E, agreed N method, dual A213/SA-213 — confirm before heat reservation |
List OD × wall (or BWG), wall basis, finish route, quantity or cut list, marking (A213 or dual A213/SA-213), Footnote D applicability, and Supplementary Requirements on one enquiry. We confirm C ≤0.035% (or Footnote D 0.040%), N 0.10–0.16%, and Table 4 75/30 ksi without inventing warehouse codes. Related grades A213 TP304L, A213 TP304N, and A213 TP316LN sit on the same hub.
FAQ
-
Is ASTM A213 the same as ASME SA-213 for TP304LN?
- No. ASTM A213 / A213M is the ASTM International product specification; ASME SA-213 / SA-213M is the separate ASME Code Book adoption. Chemistry and tensile floors align closely for a given referenced edition, but they remain two independent standards. Dual-mark only when the purchase order asks for both names on the stencil and MTC.
-
Does ASTM A213 TP304LN include welded tube?
- No. ASTM A213 covers seamless tube only — no WLD or HCW manufacturing type. Cold-finished versus hot-finished seamless tube is the process choice under A213. Welded stainless pipe belongs to a different product standard and a different steelspecs page family.
-
What carbon and nitrogen limits apply to A213 TP304LN?
- Melt carbon is ≤0.035%, with Footnote D allowing ≤0.040% for small-diameter or thin-wall tube that needs many drawing passes. Nitrogen is a mandatory band of 0.10–0.16%. Nitrogen analysis method is by agreement under Footnote B. Confirm Footnote D’s OD/wall trigger on the ordered edition before treating a secondary catalogue note as acceptance text.
-
TP304LN vs TP304L — why add nitrogen under A213?
- TP304L accepts a lower Table 4 floor of 70 ksi [485 MPa] / 25 ksi [170 MPa] with low carbon and no nitrogen requirement. TP304LN keeps the L-grade carbon ceiling but adds N 0.10–0.16% so Table 4 returns to 75/30 ksi. Order LN when the designer needs both as-welded IGC resistance and TP304-class tensile numbers on the same tube.
-
TP304LN vs TP304N — which should I specify?
- Order TP304LN when as-welded intergranular resistance drives the low-carbon ceiling. Order TP304N when standard carbon ≤0.08% is acceptable and the higher 80/35 ksi floor is the mechanical driver. Dual LN/N certification is uncommon because the carbon windows conflict — ask explicitly if a heat must clear both, and expect chemistry selection to be tight.
-
Is the nickel band for TP304LN the same as TP304L under A213?
- Under the public A213 stainless table excerpt used here, TP304LN lists nickel 8.0–11.0%, matching TP304N, while TP304L lists 8.0–12.0%. Do not assume A312 pipe nickel windows apply to A213 tube certificates. Confirm the ordered edition’s table row before writing a purchase-order chemistry window.
-
Does Table 4 set a hardness limit for TP304LN?
- Yes. Hardness maximum is 192 HBW / 200 HV or 90 HRB, alongside 75/30 ksi tensile/yield and 35% elongation. Hardness tests are part of lot acceptance under A213. Tighter project hardness windows must be written into the purchase order as additional requirements.
-
Minimum wall vs average wall for A213 TP304LN — which do I order?
- Order minimum wall when the design assumes a guaranteed minimum thickness after tolerance. Order average wall only when the PO explicitly allows it and the designer accepts that basis. Footnote D’s carbon relief for small OD/thin wall does not change which wall basis you must name on the enquiry.
-
What heat treatment does A213 require for TP304LN?
- Solution treatment at a minimum of 1900 °F [1040 °C] with water quench or other rapid cool. Both cold-finished and hot-finished seamless tube follow that requirement. Ask the mill to state anneal temperature and quench method on the EN 10204 3.1 certificate.
-
Should I order A262 Practice E with TP304LN tube?
- Often yes when as-welded IGC resistance is why you chose LN in the first place. A213 does not automatically include Practice E; invoke it as a Supplementary Requirement or clear PO wording so the test is contractual. Mills will not assume IGC testing from a verbal "full certs" note.
-
Can you dual-certify A213/SA-213 TP304LN or TP304LN/TP304L?
- Dual A213/SA-213 marking is available when the PO requests both independent standards. Dual TP304LN/TP304L is possible when the heat meets LN nitrogen plus L-grade carbon and when tensile/hardness clear both Table 4 rows — LN’s 75/30 ksi floor is stricter than L’s 70/25, so the LN row usually governs. Spell the marking on the enquiry.
Conclusion
ASTM A213 TP304LN / UNS S30453 is the low-carbon, nitrogen-strengthened 18-8 seamless tube grade for boiler, superheater, and heat-exchanger service when as-welded intergranular resistance and a 75/30 ksi Table 4 floor must travel on the same MTC. SHH STEEL supplies cold-finished and hot-finished seamless tube in the usual OD × wall / BWG band, solution annealed at 1900 °F [1040 °C], tested to Table 4 tensile and hardness limits, and documented on EN 10204 3.1 certificates — with dual SA-213 marking only when the order asks. For sister L and N grades, start from the A213/A213M hub, then send OD × wall, wall basis, Footnote D notes, and marking requirements so we can align mill and near-term availability.
Contact: admin@steelspecs.com