ASTM A213 TP304L Stainless Steel Tube | ASTM A213 Stainless Steel - SHH STEEL

ASTM A213 TP304L Stainless Steel Tube

ASTM A213 TP304L / UNS S30403 seamless boiler, superheater and heat-exchanger tube with C ≤0.035% (Footnote D to 0.040% on small-OD / light-wall), Cr 18.0–20.0%, Ni 8.0–12.0%, a 70/25 ksi Table 4 floor, hardness max 192 HBW / 90 HRB, and a 1900 °F solution anneal. SHH STEEL supplies cold-finished and hot-finished seamless tube with EN 10204 3.1 MTCs.
Grade
TP304L / UNS S30403
Standard
ASTM A213 / A213M
Product form
Seamless boiler / superheater / heat-exchanger tube (cold-finished and hot-finished)
Size
Typical OD × min wall (or average wall) within ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD and ~0.015–0.500 in. [0.4–12.7 mm] wall; other diameters by agreement
Share:
Overview
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASTM A213 TP304L Stainless Steel Tube

ASTM A213 / A213M is the ASTM International product specification for seamless ferritic and austenitic alloy-steel boiler, superheater, and heat-exchanger tubes. Grade TP304L is the low-carbon member of the 18-8 family listed under UNS S30403, written so as-welded tube-to-tubesheet joints and other sensitizing thermal cycles are less likely to leave a chromium-depleted grain-boundary network. Table chemistry caps carbon at 0.035% on the melt (with Footnote D allowing 0.040% max on small-diameter or thin-wall tube that needs many drawing passes), keeps chromium at 18.0–20.0%, and widens nickel to 8.0–12.0% — a band that is deliberately broader than the 8.0–11.0% window on standard A213 TP304. Buyers who write “304L HX tube” on a bill of materials still need to name A213 (or the separate ASME SA-213 adoption) on the purchase order so the mill applies the tube product standard, minimum-wall rules, hardness tests, and marking clauses — not a generic pipe or plate callout.

SHH STEEL can supply ASTM A213 TP304L stainless steel tube as seamless cold-finished and hot-finished product in the usual boiler and heat-exchanger OD × wall / BWG band, shipped with EN 10204 3.1 mill test certificates that report the full ladle chemistry and the Table 4 tensile and hardness results. When a project also needs ASME Code Book marking, we dual-mark A213 / SA-213 on the same lengths only if the purchase order says so — ASTM A213 and ASME SA-213 remain two independent standards. Browse the grade family on the A213/A213M hub.

Commercially, TP304L tube is still called 304L, low-carbon 304, or S30403 boiler/HX tube; none of those shop names replace the ASTM grade on the MTC or stencil. Sister grades under the same ASTM standard include A213 TP304, A213 TP304H, A213 TP316L, A213 TP321, and A213 TP347. A213 covers seamless tube only — there is no welded or HCW manufacturing type under this product standard — so cold-finished versus hot-finished seamless route is the finish/process choice, not a WLD/HCW stencil letter.

Chemical Composition of A213 TP304L

Two chemistry layers matter for TP304L under ASTM A213. The melting (heat or ladle) analysis is mandatory for every heat under the stainless chemistry table, while product analysis on finished tube applies only when Supplementary Requirement wording or the purchase order invokes product analysis through the general requirements in ASTM A1016/A1016M. Product-analysis tolerances are not reprinted as a standalone chemistry table inside A213 itself; when ordered, they typically flow from ASTM A480/A480M Table A1.1 via that general-requirements path. SHH STEEL reports the actual ladle carbon at or below the 0.035% ceiling (or the Footnote D 0.040% ceiling when that thin-wall path applies) and does not advertise a tighter “0.030 shop grade” that the ASTM stainless table does not publish.

The tables below reproduce the heat analysis for TP304L / UNS S30403 and the product-analysis limits that result from applying A480 Table A1.1 tolerances. Values are maximum unless a range is shown, and an ellipsis (…) means the ordered edition sets no requirement for that element, so it need not be determined or reported on the certificate. Confirm the ordered A213/A213M edition on the purchase order — table number (Table 1 versus Table 2 for stainless) and any nitrogen row can shift by year.

Melting analysis (heat / ladle analysis)

Element TP304L (UNS S30403) melting analysis
Carbon (C) ≤ 0.035 D
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 18.0 – 20.0
Nickel (Ni) 8.0 – 12.0
Molybdenum (Mo) … (no requirement)
Nitrogen (N) … (no requirement; analysis method by agreement when reported)

Source: ASTM A213/A213M stainless chemistry table for Grade TP304L / UNS S30403 (public specification table excerpts cross-checked). Footnote D: for small diameter or thin walls, or both, where many drawing passes are required, a carbon maximum of 0.040% is necessary in Grades TP304L, TP304LN, TP316L, and TP316LN. Confirm the ordered edition before treating any secondary catalogue as the acceptance text.

Product analysis — A480/A480M Table A1.1 tolerances applied to melt limits

Element Melting Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.035 0.01 over ≤ 0.045
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 18.0 – 20.0 0.20 under / over 17.80 – 20.20
Nickel (Ni) 8.0 – 12.0 0.10 under / 0.15 over 7.90 – 12.15

The chemistry story for TP304L is low carbon first, then the familiar 18-8 balance. Holding C ≤0.035% on the melt (or ≤0.040% under Footnote D) reduces the carbon available to form chromium carbides at grain boundaries during welding or slow cooling through the sensitizing range, which is why exchanger fabricators specify L-grade tube for as-welded tube-to-tubesheet service. Nickel at 8.0–12.0% is wider than TP304’s 8.0–11.0% band under the same A213 stainless table — do not copy an A312 pipe Ni window onto an A213 tube certificate. Molybdenum is a no-requirement ellipsis; when chloride pitting resistance is the driver, open A213 TP316L rather than stretching TP304L.

When product analysis is ordered, finished tube may read up to C 0.045%, Mn 2.04%, P 0.055%, S 0.035%, and Si 1.05%, with Cr 17.80–20.20% and Ni 7.90–12.15%. Those are the only product limits we quote from the A480 A1.1 path. Put any tighter project carbon ceiling on the purchase order before the heat is selected, and say whether Footnote D applies to the OD × wall you are buying.

Mechanical Properties of A213 TP304L

ASTM A213 Table 4 sets the tensile acceptance floor for TP304L at 70 ksi [485 MPa] tensile strength and 25 ksi [170 MPa] yield strength (0.2% offset), with elongation of 35% minimum in 2 in. or 50 mm. That 70/25 ksi pair is deliberately lower than the 75/30 ksi floor on TP304 — the trade-off that comes with guaranteed low carbon. Unlike many ASTM A312 pipe rows for the same UNS number, A213 Table 4 also lists a hardness maximum for TP304L of 192 HBW / 200 HV or 90 HRB, and hardness tests are part of the lot acceptance scheme in the product standard. Every lot sampled under the edition’s specimen rules must meet those numbers after the final solution treatment.

Property TP304L requirement (Table 4)
Tensile strength, min 70 ksi [485 MPa]
Yield strength (0.2% offset), min 25 ksi [170 MPa]
Elongation in 2 in. or 50 mm, min 35%
Hardness, max 192 HBW / 200 HV or 90 HRB

Source: ASTM A213/A213M Table 4 for TP304L / UNS S30403 (public specification summaries). Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or thinner than 0.015 in. [0.4 mm] wall. Flattening and flaring tests are also required on a lot basis for finished tube; they sit beside tension and hardness rather than replacing them.

Dual TP304/TP304L certification is common when a heat meets the tighter carbon rules and still clears the higher 75/30 ksi TP304 tensile floor plus both hardness maxima — ask for that dual marking on the purchase order rather than assuming it from a PMI gun. For creep-range boiler service that needs a controlled carbon floor and grain-size language, open A213 TP304H rather than stretching low-carbon TP304L into H-grade framing.

Dimensions and Tolerances

Dimensional supply for ASTM A213 TP304L is tube language — outside diameter × wall thickness (minimum wall or average wall) and, commercially, BWG / gauge — not ASME B36.19 pipe schedules as the primary size story. The sizes usually furnished under A213 run from about 1/8 in. [3.2 mm] inside diameter to 5 in. [127 mm] outside diameter, with minimum wall from about 0.015 to 0.500 in. [0.4 to 12.7 mm]; tubing with other diameters may be furnished when all other requirements of the specification are met. State on the purchase order whether wall is minimum or average, because that choice changes how the mill interprets tolerance and how the designer reads remaining wall after fabrication.

Outside-diameter and wall variations follow ASTM A1016/A1016M as invoked by A213, with cold-finished and hot-finished routes carrying different practical bands. Cold-finished tubes commonly hold tighter OD control; hot-finished tubes allow wider OD and wall windows. Permissible variations from a specified average wall for cold-finished tube are often summarized as ±10% of the specified average wall, while minimum-wall product is accepted to the A1016 minimum-wall tables rather than a symmetric ± window. Confirm the exact A1016 rows for the OD and finish route on the ordered edition — and remember Footnote D when the OD × wall is small enough that many drawing passes push the carbon path to 0.040% max.

Item Typical A213 TP304L dimensional practice
Product form Seamless only (cold-finished or hot-finished)
Usual size band ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD; wall ~0.015–0.500 in. [0.4–12.7 mm] min (or average wall if PO says so)
Wall basis Minimum wall (default commercial practice) or average wall when specified
OD / wall tolerances Per ASTM A1016/A1016M for the finish route and size; cold-finished average wall often ±10%
Length Cut lengths for HX / boiler bundles, or mill random lengths by agreement
Secondary size note ASME B36.19 schedules may appear only when a buyer asks for a pipe-schedule cross-reference — not as the primary A213 size callout

Put the cut list, U-bend or straight-tube preference, and end preparation on the enquiry so mill and stock lengths can be mixed efficiently. Minimum wall is a first-class A213 concept: if the datasheet assumes average wall, say so explicitly before the heat is rolled.

Equivalent Grades

Equivalence language around TP304L tube is often looser than a boiler or heat-exchanger purchase order can afford. ASTM A213 Grade TP304L / UNS S30403 is the governing designation for this article; EN 1.4306 / 1.4307 and JIS SUS304L are approximate wrought names that point to similar low-carbon chemistry families but are not automatic substitutes on an A213 mill test certificate. When a datasheet says “equivalent to 304L,” confirm which product standard, tensile/hardness table, and heat-treatment clause the mill will actually certify.

Designation Notes
ASTM A213 / A213M Grade TP304L Governing ASTM seamless boiler / HX tube product standard for this article
UNS S30403 Unified number listed in the stainless chemistry table
ASME SA-213 TP304L Separate ASME Code Book adoption of the A213 grade text — dual-mark only when the PO asks
EN 1.4306 / 1.4307 Approximate wrought low-carbon stainless designations; order EN tube forms under the relevant EN tube specs
JIS SUS304L Approximate Japanese grade name; confirm the Japanese tube product standard when ordering JIS product
Related plate A240 / SA240 flat product in the same UNS family — order plate and tube under their own product standards

ASME SA-213 TP304L is the separate Code Book adoption of the same grade text; dual A213/SA-213 marking is a purchase-order option, not a claim that the two standards are one document. Compare standard-carbon, H-grade, and molybdenum sisters on their own ASTM A213 pages before swapping grades in a tube bundle.

Heat Treatment and Delivery Condition

TP304L under ASTM A213 is furnished solution treated at a minimum of 1900 °F [1040 °C], then quenched in water or cooled rapidly by other means at a rate sufficient to prevent carbide reprecipitation. That heat-treatment row applies to both cold-finished and hot-finished seamless tube. The low-carbon chemistry reduces sensitization risk, but it does not replace the solution anneal — under-cooling or skipping the quench can still leave a structure that fails a contractual A262 capability check even when ladle carbon looked acceptable on paper.

Cold-finished versus hot-finished is a process and dimensional route, not a substitute for the anneal: cold-finished tube is typically drawn after hot working and then solution treated; hot-finished tube may be quenched after hot forming when the edition allows and finishing temperature is not below the minimum anneal. Delivery condition for SHH STEEL TP304L is solution annealed and pickled (or bright annealed by agreement), with heat-treatment temperature and quench method stated on the EN 10204 3.1 certificate. Straightening, cutting, and end finishing follow heat treatment.

When Supplementary Requirement language for intergranular-corrosion capability (commonly tied to ASTM A262 Practice E on sensitized specimens for low-carbon types) is ordered, the corrosion test report travels with the heat-treatment record. H-grade grain-size rules do not rewrite the TP304L path — use A213 TP304H when the datasheet calls for H-grade carbon and grain-size controls.

Corrosion Resistance

TP304L’s main corrosion advantage over standard TP304 is intergranular resistance after welding or after exposure in the sensitizing temperature band — the reason fabricators pick L-grade tube for as-welded tube-to-tubesheet joints in exchangers and condensers. The chromium-rich passive film still handles a wide band of oxidizing process fluids, clean steam-side and water-side duties, and many organic media that do not lean heavily on chlorides. In chloride-bearing waters, coastal cooling circuits, and many brine-leaning heat-exchanger services, pitting and crevice attack become limiting, and buyers usually step up to A213 TP316 or A213 TP316L rather than expecting low carbon alone to solve chloride pitting.

ASTM A213 itself does not publish a corrosion-rate table for TP304L; selection remains engineering judgment against fluid, temperature, velocity, and inspection philosophy inside the boiler or exchanger. When a specification calls for ASTM A262 Practice E, write that Supplementary Requirement onto the purchase order so the test is contractual rather than assumed from a verbal “full certs” note. SHH STEEL will not rank TP304L as equal to 316L in chlorides — that claim is not supported by the product standard.

Applications of A213 TP304L Tube

TP304L is ordered when the exchanger or condenser fabrication sequence leaves tube-to-tubesheet joints as-welded, or when the owner wants low-carbon austenitic tube documentation under A213 without stepping into molybdenum grades. The table below pairs typical application areas with a selection note so the grade is chosen for the welding sequence and fluid — not only for the familiar “304L” name on the BOM.

Application area Typical use of TP304L tube Selection note
Heat exchangers / condensers Straight and U-bend HX tubes with as-welded or lightly fabricated tube-to-tubesheet joints State min vs average wall, BWG, bend radius, and any A262 SR on the enquiry
Boiler and moderate-temperature steam Seamless generating-bank and utility steam tubing where L-grade IGC resistance is preferred For creep-critical H-grade service open TP304H; L-grade is not an H substitute
Chemical and process Tube-side or shell-side circuits with oxidizing or mild corrosive media and welded attachments Prefer TP316L if chlorides dominate
Food / pharmaceutical utilities Utility and process HX where low-carbon 304 stainless tube is accepted Follow hygiene finish and welding procedure requirements
Cryogenic / low-temperature HX Austenitic toughness in cold-box and LNG-related exchangers with welded joins Confirm low-temperature code acceptance for the grade
Dual-certified tube duty Heats marked TP304/TP304L when both Table 4 rows and carbon rules are cleared Ask for dual marking on the PO — do not assume from PMI alone

For chloride-rich cooling water move to the molybdenum grades on the same A213/A213M hub; for creep-range boiler tubing open TP304H; for standard-carbon service without as-welded IGC concern, A213 TP304 remains the reference 18-8 tube grade.

Weldability

TP304L tube is chosen in large part because it welds cleanly for tube-to-tubesheet joints, attachment welds, and fabrication joins while keeping base-metal carbon low enough to resist sensitization in the heat-affected zone. Common practice uses ER308L (or equivalent covered electrodes) under a qualified WPS so the weld metal carbon stays aligned with the L-grade base tube. Heat input control, interpass limits, and post-weld cleaning remain the fabricator’s responsibility under the applicable boiler or pressure-vessel code — A213 governs the seamless tube product, not the field or shop weld procedure.

Because A213 TP304L is seamless, there is no mill longitudinal weld to radiograph the way welded pipe standards describe. Focus inspection language on tube integrity (hydro or NDE of each length), tube-to-tubesheet joint quality, and any contractual corrosion test on the base metal. Specify end preparation and surface finish on the tube PO when orbital or clean-service joins are planned. If chlorides dominate after welding, changing the base metal to A213 TP316L is usually a better move than relying on filler selection alone.

Surface Finishes

Standard mill delivery for ASTM A213 TP304L is solution annealed and pickled, leaving a clean matte finish suitable for most boiler and heat-exchanger tube duty. Bright annealing under protective atmosphere produces a smoother reflective surface used on some clean-process and instrumentation tube lines and must be called out because it changes the heat-treatment route. Light polish or specified Ra on the bore or OD is a commercial or service-center operation on top of A213 product, not automatic with the grade stamp.

When a hygienic or fouling-sensitive exchanger specification quotes an Ra maximum on the bore, put it on the tube purchase order with its own acceptance language and sampling plan. SHH STEEL stencils grade and heat treatment as standard requirements; polish, special OD grind, and passivation after fabrication remain commercial extras unless the contract says otherwise. End preparation (plain, slightly beveled, or as needed for tube expanding) should be ordered together with finish so receiving inspection shares one acceptance language.

Inspection and Testing

Base ASTM A213 testing for TP304L includes heat analysis, tension tests to the Table 4 70/25 ksi floors, hardness tests to the Table 4 maximum, flattening and flaring tests on a lot basis, and either hydrostatic testing or nondestructive electric testing of each length. The manufacturer may choose hydro versus NDE unless the purchase order fixes the method; both are acceptance routes inside the product standard, not informal upgrades. Marking includes the ASTM designation, grade, size, heat number, and other clause-required data so receiving inspection can tie each length back to the MTC.

Supplementary Requirements commonly added on TP304L tube orders are summarized below. Invoke them by number or clear purchase-order wording; mills will not assume product analysis or intergranular-corrosion testing from a verbal “full certs” note.

Option Purpose
Product analysis Confirms chemistry on finished tube (via A1016 / PO language)
Intergranular corrosion A262 Practice E on sensitized specimens (low-carbon types) as a contractual Supplementary Requirement
Minimum vs average wall States which wall basis the size callout uses
Fixed hydro or NDE method Removes manufacturer’s option when the end user mandates one route
Third-party inspection / EN 10204 3.2 Witnessed testing and certificate when the project requires it
Dual TP304/TP304L marking When ladle carbon and both Table 4 rows support dual certification

Lot definitions for continuous heat treatment or direct quench after hot forming follow the size-based lot sizes in A213; ask the mill to state lot identity clearly on the certificate so hardness and tension specimens map cleanly to the bundle you receive.

Packaging and Shipping

TP304L tube leaves SHH STEEL bundled, capped or end-protected, and tagged for export or domestic delivery according to the length mix and bend form on the order. Bundle tags repeat the ASTM A213 grade, OD × wall (or BWG), heat number, and PO reference so site receiving can check the shipment without opening every certificate packet first. U-bent tubes need extra cradle or case protection so bend radii and legs are not distorted in transit.

Export packing can be bare bundles, wrapped bundles, or wooden-cased lengths for bright-annealed, polished, or small-bore material. We ship under the Incoterms on the order acknowledgement — FOB, CFR, CIF, EXW, or other agreed terms. Inland trucking, bilingual destination marks, or project color coding for bundle tags should be stated on the enquiry beside the metallurgical notes.

Why Choose SHH STEEL

SHH STEEL treats ASTM A213 TP304L as a product standard with enforceable low-carbon chemistry, tensile, hardness, heat-treatment, and marking rules — not as a catalogue nickname for “any 304L tube.” The MTC reports the ladle carbon against the 0.035% (or Footnote D 0.040%) ceiling and the Table 4 70/25 ksi tensile/hardness set; the stencil carries seamless tube identity under A213; and dual A213/SA-213 marking is offered only when requested so Code and non-Code jobs stay cleanly documented.

We keep the 304-family conversation honest for boiler and HX duty. If standard-carbon tensile floors are required and as-welded IGC is not the driver, we open A213 TP304. If creep-range boiler service needs H-grade carbon and grain-size controls, we open A213 TP304H. If chlorides dominate the cooling water or process fluid, we open A213 TP316L. The A213/A213M hub is organized the same way — grade by grade under ASTM, seamless tube only.

Lead times combine near-term stock lengths with mill schedules; we say which is which on the quotation. Cut-to-length, U-bending, polish, and third-party inspection are defined extras. The tube that arrives should match the ASTM callout the engineer wrote, with paperwork a third-party inspector can read without translation.

Supply Capability

SHH STEEL can supply ASTM A213 TP304L stainless steel tube against the edition and finish route named on your enquiry. The capability table below summarizes the sizes, finishes, and documents we regularly quote for this low-carbon grade, followed by the Stock / Available sizes map buyers ask for when they need a quick sense of what to enquire against for boiler and heat-exchanger duty.

Item SHH STEEL capability for TP304L
Standard ASTM A213 / A213M (dual SA-213 marking on request) Grade TP304L / UNS S30403
Product form Seamless only — cold-finished and hot-finished
Size Typical OD × min wall (or average wall) in the A213 usual band; other diameters by agreement
Wall / gauge Minimum wall or average wall; BWG / gauge callouts accepted on enquiry
Length Cut-to-length for HX / boiler bundles; mill random by agreement; U-bends on enquiry
Finish Annealed and pickled; bright annealed or light polish by agreement
Testing Tension (70/25 ksi), hardness (max 192 HBW / 90 HRB), flattening, flaring, hydro or NDE per length; full ladle chemistry on MTC; product analysis / IGC on order
Documents EN 10204 3.1 with full ladle chemistry; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Stock / Available sizes

SHH STEEL quotes TP304L tube against a practical stock-and-mill enquiry range rather than a frozen warehouse SKU list. The sizes below are the OD × wall / BWG combinations buyers most often request for as-welded HX and condenser duty; availability of any single line on a given week depends on mill drawing and our inbound schedule, so treat the table as a supply map for enquiry — not a guarantee that every line sits on the floor with a published tonnage.

Item Typical stock / enquiry range for TP304L
Outside diameter 12.7, 15.88, 19.05, 25.4, 31.8, 38.1, 50.8, 63.5, 76.2 mm (and other HX/boiler ODs on enquiry; up through the usual A213 ~5 in. [127 mm] band)
Wall / BWG BWG 10–20 class walls and metric min-wall equivalents; lighter and heavier walls by agreement
Common OD × wall examples 19.05 × 1.65 mm; 19.05 × 2.11 mm; 25.4 × 2.11 mm; 25.4 × 2.77 mm; 31.8 × 2.77 mm; 38.1 × 2.77 mm; 50.8 × 2.77 mm — illustrative HX/condenser sizes, confirm min vs average wall
Length Cut lengths for exchanger bundles; U-bends and straight random lengths on enquiry
Special Non-standard OD/wall, bright anneal, polished bore, dual TP304/TP304L, and dual A213/SA-213 marking — confirm on enquiry before the heat is reserved

When you send an enquiry, list OD × wall (or BWG), wall basis (minimum or average), cold-finished or hot-finished preference, quantity or cut list, required marking (A213 alone, dual A213/SA-213, and/or dual TP304/TP304L), and any Supplementary Requirements including A262. We reply with what we can ship from near-term stock versus what needs a mill run, without inventing fake warehouse codes or tonnage claims.

Send the size list, finish route, quantity or cut lengths, required marking, Supplementary Requirements, and destination on one enquiry. We will confirm chemistry and the 70/25 ksi tensile/hardness set against the ordered edition, state what ships from near-term availability versus mill production, and keep the offer aligned with the ASTM A213 / A213M product standard that governs this page. Related grades such as A213 TP316, A213 TP321, and A213 TP347 sit on the same hub when the datasheet steps beyond low-carbon 18-8.

FAQ

Is ASTM A213 the same as ASME SA-213 for TP304L?
No. ASTM A213 / A213M is the ASTM International product specification for seamless boiler, superheater, and heat-exchanger tubes; ASME SA-213 / SA-213M is the separate ASME Code Book adoption of that grade text. Chemistry, tensile, and hardness floors align closely for a given referenced edition, but they remain two independent standards. Dual-mark A213/SA-213 tube only when the purchase order asks for both names on the stencil and MTC.
Does ASTM A213 TP304L include welded or HCW tube?
No. ASTM A213 covers seamless tube only. There is no WLD or HCW manufacturing type under this product standard the way ASTM A312 describes pipe. The process choice for TP304L under A213 is cold-finished versus hot-finished seamless tube, plus the heat-treatment and testing clauses of the ordered edition. If you need welded stainless pipe, that is a different product standard and a different steelspecs page family.
What does Footnote D mean for TP304L carbon under A213?
Footnote D states that for small diameter or thin walls, or both, where many drawing passes are required, a carbon maximum of 0.040% is necessary in Grades TP304L, TP304LN, TP316L, and TP316LN. The default melt ceiling remains 0.035%. Put the OD × wall and whether Footnote D applies on the enquiry so the mill selects a heat that matches the path you are buying, and confirm the footnote text on the ordered edition.
Minimum wall vs average wall — which should I order for A213 TP304L?
Order minimum wall when the design and datasheet are written around a guaranteed minimum thickness after tolerance. Order average wall only when the purchase order explicitly allows average-wall product and the designer has accepted that basis. The two readings produce different tube from the same OD × wall line, so put the wall basis on the enquiry before the mill selects tooling and tolerance tables from A1016.
Hydrostatic test vs NDE — which do I get on TP304L tube?
ASTM A213 requires each tube to be hydrostatically tested or nondestructively electrically tested. The manufacturer may choose the method unless the purchase order fixes one. Neither route is an informal upgrade over the other inside the product standard. State the preferred method on the enquiry if your end user or inspector mandates hydro only or a named NDE technique.
Does A213 Table 4 set a hardness limit for TP304L?
Yes. Table 4 for TP304L lists tensile strength 70 ksi, yield strength 25 ksi, elongation 35%, and a hardness maximum of 192 HBW / 200 HV or 90 HRB. Hardness tests are part of lot acceptance under A213, which differs from many A312 pipe rows for the same UNS number that omit a Table 4 hardness cap. If a project needs a tighter hardness window than Table 4, write it into the purchase order as an additional requirement.
What is the UNS number and chemistry of ASTM A213 TP304L?
TP304L is UNS S30403. Melting limits include carbon ≤0.035% (Footnote D to 0.040% on small-OD / light-wall), manganese ≤2.00%, phosphorus ≤0.045%, sulfur ≤0.030%, silicon ≤1.00%, chromium 18.0–20.0%, and nickel 8.0–12.0%, with molybdenum and nitrogen as no-requirement ellipses in the public table excerpts used here. Note the A213 nickel band is 8.0–12.0%, not the wider A312 pipe window — order tube under A213 chemistry.
TP304 vs TP304L — which A213 tube should I order?
Order TP304 when the specification calls for the standard 75/30 ksi tensile floor and carbon ≤0.08% is acceptable. Order TP304L when as-welded intergranular resistance is the driver and the lower 70/25 ksi floor is acceptable. Dual TP304/TP304L certification is possible on qualifying heats — ask for it on the PO rather than assuming it from a PMI gun reading.
TP304L vs TP316L — when do I need molybdenum under A213?
Order TP316L when chloride pitting or crevice corrosion dominates the cooling water or process fluid and you still need low-carbon as-welded resistance. TP304L remains appropriate for many oxidizing and low-chloride steam and process services where molybdenum is not justified. ASTM A213 does not publish a chloride ranking table; open the TP316L tube page on the hub when chlorides drive the selection.
TP304L vs TP304H — can L-grade replace H-grade boiler tube?
No. TP304H carries the H-grade carbon range, grain-size controls, and creep-rupture framing that creep-critical boiler and superheater datasheets expect. TP304L is the low-carbon, as-welded IGC grade with a 70/25 ksi tensile floor. Do not treat "304L" as a synonym stamp for H-grade service on the MTC, and do not stretch L-grade into creep-range framing without a design review.
What heat treatment does ASTM A213 require for TP304L?
TP304L is solution treated at a minimum of 1900 °F [1040 °C] and then water quenched or rapidly cooled to prevent carbide reprecipitation. Both cold-finished and hot-finished seamless tube follow that heat-treatment requirement. Ask the mill to state anneal temperature and quench method on the EN 10204 3.1 certificate so receiving inspection can clear the heat without chasing verbal confirmations.
Can you dual-certify ASTM A213 and ASME SA-213 TP304L, or TP304/TP304L?
Yes on both axes when the heat and testing support it. Dual A213/SA-213 marking is available when the purchase order requests both independent standards on the stencil and MTC. Dual TP304/TP304L is available when ladle chemistry meets the tighter carbon rules and tensile plus hardness results clear both Table 4 rows. Spell the required marking on the enquiry so the heat is selected correctly.

Conclusion

ASTM A213 TP304L / UNS S30403 is the low-carbon 18-8 seamless stainless steel tube grade for boiler, superheater, and heat-exchanger service when as-welded intergranular resistance matters and molybdenum is not required. SHH STEEL supplies cold-finished and hot-finished seamless tube in the usual OD × wall / BWG band, solution annealed, tested to the Table 4 70/25 ksi tensile and hardness limits, and documented on EN 10204 3.1 certificates — with dual SA-213 marking only when the order asks for that separate ASME standard. For sister grades and stock-oriented size discussions, start from the A213/A213M hub, then send your OD × wall list, wall basis, Footnote D applicability, and marking requirements so we can align mill and near-term availability to the ASTM callout.

Contact: admin@steelspecs.com

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X