ASTM A213 TP316N Stainless Steel Tube | ASTM A213 Stainless Steel - SHH STEEL

ASTM A213 TP316N Stainless Steel Tube

ASTM A213 TP316N / UNS S31651 nitrogen-strengthened molybdenum seamless boiler, superheater and heat-exchanger tube — C ≤0.08%, Cr 16.0–18.0%, Ni 10.0–13.0%, Mo 2.00–3.00%, N 0.10–0.16%, Table 4 80/35 ksi floor, hardness max 192 HBW / 90 HRB, 1900 °F solution anneal with Footnote F quench/A262 capability. SHH STEEL supplies cold-finished and hot-finished seamless tube with EN 10204 3.1 MTCs that report nitrogen and molybdenum.
Grade
TP316N / UNS S31651
Standard
ASTM A213 / A213M
Product form
Seamless boiler / superheater / heat-exchanger tube (cold-finished and hot-finished)
Size
Typical OD × min wall (or average wall) within ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD and ~0.015–0.500 in. [0.4–12.7 mm] wall; other diameters by agreement
Share:
Overview
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASTM A213 TP316N Stainless Steel Tube

ASTM A213 / A213M is the product specification for seamless ferritic and austenitic alloy-steel boiler, superheater, and heat-exchanger tubes. Grade TP316N / UNS S31651 is the nitrogen-strengthened member of the molybdenum-bearing 316 family: melting carbon is capped at 0.08%, chromium 16.0–18.0%, nickel held in a narrower 10.0–13.0% band (not the 10–14% window used on TP316 / TP316L), molybdenum 2.00–3.00%, and nitrogen locked into a mandatory 0.10–0.16% range. That nitrogen floor is why Table 4 lifts tensile acceptance to 80 ksi [550 MPa] / 35 ksi [240 MPa] — five / five ksi above ordinary A213 TP316 — while molybdenum still does the chloride-leaning corrosion work that A213 TP304N cannot claim.

SHH STEEL can supply ASTM A213 TP316N stainless steel tube as seamless cold-finished and hot-finished product in the usual boiler and heat-exchanger OD × wall / BWG band, shipped with EN 10204 3.1 mill test certificates that report the full ladle chemistry — nitrogen and molybdenum both visible — plus the Table 4 tensile and hardness results. Dual A213 / SA-213 marking is offered only when the purchase order asks for both independent standards. Start from the A213/A213M hub for the rest of the 316-family tube grades.

Commercial shorthand such as 316N, S31651, or “nitrogen 316 HX tube” never replaces the ASTM grade on the MTC or stencil. Sister grades under the same ASTM standard include A213 TP316, A213 TP316L, A213 TP316LNM, A213 TP316H, and A213 TP304N. A213 covers seamless tube only — there is no welded or HCW manufacturing type — so cold-finished versus hot-finished seamless route is the finish/process choice.

Chemical Composition of A213 TP316N

Two chemistry layers matter for TP316N under ASTM A213. Melting analysis is mandatory for every heat; product analysis on finished tube applies only when Supplementary Requirement wording or the purchase order invokes it through ASTM A1016/A1016M, with tolerances typically from ASTM A480/A480M Table A1.1. Nitrogen analysis method is a matter of agreement (Footnote B). The first line a reviewer should check is the nitrogen band 0.10–0.16% — without it the heat is not TP316N. The second line often missed: nickel is 10.0–13.0% under A213 for this grade, not the wider 10.0–14.0% band used on TP316 / TP316L. Molybdenum 2.00–3.00% remains mandatory.

The tables below reproduce the melt limits for TP316N / UNS S31651, the product-analysis limits from A480 Table A1.1 practice, and a short nitrogen / nickel / molybdenum snapshot against TP316 and TP316LNM. Later A213 editions place austenitic stainless grades in Table 2 (older editions used Table 1); confirm the ordered edition on the purchase order.

Melting analysis (heat / ladle analysis)

Element TP316N (UNS S31651) melting analysis
Carbon (C) ≤ 0.08
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 16.0 – 18.0
Nickel (Ni) 10.0 – 13.0
Molybdenum (Mo) 2.00 – 3.00
Nitrogen (N) 0.10 – 0.16

Source: ASTM A213/A213M stainless chemistry table for Grade TP316N / UNS S31651 (public mill / specification PDF excerpt — _ref_a213.txt / A213–13 table text). Confirm the ordered edition. Do not copy an A240 plate Ni window of 10–14% onto an A213 TP316N tube certificate — this product table prints 10.0–13.0%.

Product analysis — A480/A480M Table A1.1 tolerances applied

Element Melting Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.08 0.01 over ≤ 0.09
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 16.0 – 18.0 0.20 under / over 15.80 – 18.20
Nickel (Ni) 10.0 – 13.0 0.10 under / 0.15 over 9.90 – 13.15
Molybdenum (Mo) 2.00 – 3.00 0.05 under / 0.10 over 1.95 – 3.10
Nitrogen (N) 0.10 – 0.16 0.01 under / 0.02 over 0.09 – 0.18

Nitrogen / nickel / Mo snapshot — TP316 / TP316N / TP316LNM

Element TP316 (S31600) TP316N (S31651) TP316LNM (S31653)
C ≤ 0.08 ≤ 0.08 ≤ 0.035
Ni 10.0 – 14.0 10.0 – 13.0 10.0 – 13.0
Mo 2.00 – 3.00 2.00 – 3.00 2.00 – 3.00
N … 0.10 – 0.16 0.10 – 0.16
Table 4 tensile / yield 75 / 30 ksi 80 / 35 ksi 75 / 30 ksi

Read nitrogen and nickel together. A heat at 13.5% Ni can clear TP316 but fails TP316N’s 13.0% ceiling. Versus A213 TP316LNM, the intentional chemistry change on TP316N is the higher carbon ceiling — LN/LNM keeps C ≤0.035% for as-welded IGC strategy while sharing the same N and Ni bands. Versus A213 TP304N, TP316N adds mandatory molybdenum and uses the 16–18 / 10–13 Cr–Ni balance instead of 18–20 / 8–11.

When product analysis is ordered, finished tube may read C ≤0.09%, Mn ≤2.04%, P ≤0.055%, S ≤0.035%, Si ≤1.05%, Cr 15.80–18.20%, Ni 9.90–13.15%, Mo 1.95–3.10%, and N 0.09–0.18%. Put any tighter project nitrogen floor or molybdenum floor on the purchase order before the heat is selected.

Mechanical Properties of A213 TP316N

ASTM A213 Table 4 sets the tensile acceptance floor for TP316N at 80 ksi [550 MPa] tensile strength and 35 ksi [240 MPa] yield strength (0.2% offset), with elongation of 35% minimum in 2 in. or 50 mm and hardness max 192 HBW / 200 HV or 90 HRB. That is five / five ksi above TP316’s 75/30 ksi pair — nitrogen is doing the strength work that ordinary 316 chemistry does not guarantee. Hardness stays at the same 192 HBW / 90 HRB ceiling used across most of the 316 family.

Property TP316N requirement (Table 4)
Tensile strength, min 80 ksi [550 MPa]
Yield strength (0.2% offset), min 35 ksi [240 MPa]
Elongation in 2 in. or 50 mm, min 35%
Hardness, max 192 HBW / 200 HV or 90 HRB

Source: ASTM A213/A213M Table 4 for TP316N / UNS S31651 (public specification PDF excerpt — _ref_a213.txt). Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or thinner than 0.015 in. [0.4 mm] wall. Flattening and flaring tests are also required on a lot basis.

Designers who assumed Mo-bearing tube stops at 75/30 ksi should re-check whether TP316N’s 80/35 ksi pair is available for the same fluid. Do not assume a TP316 certificate clears TP316N — nitrogen must be present, reported, and inside 0.10–0.16%. When low carbon is also required with nitrogen and molybdenum, open A213 TP316LNM.

Dimensions and Tolerances

Dimensional supply for ASTM A213 TP316N is tube language — OD × wall (minimum or average) and commercially BWG / gauge — not ASME B36.19 pipe schedules as the primary size story. Usual A213 sizes run from about 1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD, with minimum wall about 0.015–0.500 in. [0.4–12.7 mm]; other diameters may be furnished when all other requirements are met. State min versus average wall on the purchase order — boiler and heat-exchanger datasheets almost always assume minimum wall.

OD and wall variations follow ASTM A1016/A1016M as invoked by A213. Cold-finished tubes commonly hold tighter OD control; hot-finished tubes allow wider windows. Cold-finished average-wall product is often summarized as ±10% of the specified average wall; minimum-wall product follows the A1016 minimum-wall tables. Confirm the exact rows for the OD and finish route on the ordered edition.

Item Typical A213 TP316N dimensional practice
Product form Seamless only (cold-finished or hot-finished)
Usual size band ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD; wall ~0.015–0.500 in. [0.4–12.7 mm] min (or average wall if PO says so)
Wall basis Minimum wall (default commercial practice) or average wall when specified
OD / wall tolerances Per ASTM A1016/A1016M for the finish route and size
Length Cut lengths for HX / boiler bundles, or mill random lengths by agreement
Secondary size note ASME B36.19 schedules only as a buyer-requested cross-reference — not the primary A213 callout

Put the cut list, U-bend preference, and end preparation on the enquiry. Minimum wall remains a first-class A213 concept regardless of N-grade chemistry.

Equivalent Grades

Equivalence language around 316N tube often collapses plate and tube product forms into one nickname, or treats TP316N as “TP316 with a little nitrogen.” ASTM A213 Grade TP316N / UNS S31651 is the governing designation for this article; EN and JIS wrought names that point to similar N-strengthened Mo chemistry families are not automatic substitutes on an A213 MTC.

Designation Notes
ASTM A213 / A213M Grade TP316N Governing ASTM seamless boiler / HX tube product standard for this article
UNS S31651 Unified number in the stainless chemistry table
ASME SA-213 TP316N Separate ASME Code Book adoption — dual-mark only when the PO asks
Related standard 316 A213 TP316 — Mo without N band; 75/30 ksi
Related LN / LNM A213 TP316LNM — same N band, C ≤0.035, 75/30 ksi
Related 304N A213 TP304N — N-strengthened without Mo
Related plate A240 / SA240 flat product in the 316N family — order plate and tube under their own standards

Dual A213/SA-213 marking is a purchase-order option. Compare TP316, TP316LNM, and TP304N on their own ASTM A213 pages before swapping N-grade Mo tube inside a boiler list.

Heat Treatment and Delivery Condition

TP316N under ASTM A213 is furnished solution treated at a minimum of 1900 °F [1040 °C], then quenched in water or cooled rapidly by other means. The heat-treatment table carries Footnote F for this grade: quench at a rate sufficient to prevent re-precipitation of carbides, as demonstrable by the capability of tubes to pass ASTM A262 Practice E when that test is specified on the purchase order. The manufacturer is not required to run A262 Practice E unless Supplementary Requirement S4 / the PO calls for it. That heat-treatment row applies to both cold-finished and hot-finished seamless tube.

Cold-finished versus hot-finished is a process and dimensional route, not a substitute for the anneal or the Footnote F quench capability. Delivery condition for SHH STEEL TP316N is solution annealed and pickled (or bright annealed by agreement), with anneal temperature, quench method, nitrogen result, and molybdenum result on the EN 10204 3.1 certificate. Straightening, cutting, and end finishing follow heat treatment.

Unlike H grades such as A213 TP316H, TP316N has no mandatory ASTM grain-size number in the public heat-treatment table. If a project datasheet asks for grain-size reporting or A262 Practice E on 316N, put that requirement on the purchase order rather than assuming base A213 includes it.

Corrosion Resistance

TP316N inherits molybdenum’s contribution to pitting and crevice resistance from the 316 family while using nitrogen to raise strength rather than to change the fundamental chloride ranking of the alloy. The 2.00–3.00% Mo band is why buyers step up from A213 TP304N when chloride-leaning or process-side aqueous corrosion sits beside a need for the 80/35 ksi floor. It is still not an L-grade: carbon up to 0.08% means as-welded intergranular corrosion risk after tube-to-tubesheet welding needs separate review — many owners use A213 TP316LNM when low carbon and nitrogen must travel together.

ASTM A213 itself does not publish a corrosion-rate table for TP316N; selection remains engineering judgment against fluid, temperature, velocity, and inspection philosophy. Footnote F’s A262 Practice E capability is a quench-quality demonstration path when ordered — write S4 / Practice E onto the purchase order so the test is contractual. SHH STEEL will not rank TP316N as equal to higher-Mo grades in severe chlorides — that claim is not supported by the product standard.

Applications of A213 TP316N Tube

Because TP316N combines molybdenum with a mandatory nitrogen band and an elevated Table 4 pair, it shows up in heat-exchanger and process tubing where designers want Mo plus higher allowable tensile/yield than standard TP316, pressure-retaining HX bundles that name 316N rather than stretching TP316, and Code-driven lists that already use TP304N logic but need molybdenum. The table below pairs typical application areas with a selection note so the grade is chosen for strength, fluid, and fabrication route — not only for the familiar “316N” name on the BOM.

Application area Typical use of TP316N tube Selection note
Higher-strength Mo HX Straight and U-bend tubes needing 80/35 ksi with Mo Confirm N 0.10–0.16% on MTC, not PMI alone
Boiler / process lists naming 316N When datasheet lifts tensile above TP316’s 75/30 State min vs average wall and BWG on the enquiry
As-welded IGC-critical joins Usually prefer TP316LNM rather than TP316N C ≤0.08% on N grade works against as-welded IGC strategy
N-strengthened without Mo Stay on TP304N when Mo is not required Do not treat TP316N as a free upgrade of TP304N
Mo without N band Stay on TP316 when 80/35 ksi not required Do not over-specify N grade for ordinary 75/30 lists

For low-carbon nitrogen Mo tube open A213 TP316LNM; for Mo without nitrogen open A213 TP316; for N without Mo open A213 TP304N on the same A213/A213M hub.

Weldability

TP316N tube welds readily with matching or near-matching molybdenum-bearing austenitic filler for tube-to-tubesheet joints, attachment welds, and fabrication joins. Common practice uses ER316 / ER316L / ER316N under a qualified WPS; some fabricators prefer nitrogen-bearing or low-carbon deposits when weld-metal strength or IGC strategy must align with the base metal. Heat input control, interpass limits, and post-weld cleaning remain the fabricator’s responsibility under the applicable boiler or pressure-vessel code — A213 governs the seamless tube product, not the field or shop weld procedure.

Because A213 TP316N is seamless, there is no mill longitudinal weld to radiograph the way welded pipe standards describe. Focus inspection language on tube integrity (hydro or NDE of each length), tube-to-tubesheet joint quality, and any contractual corrosion test on the base metal. For tube that will enter service as-welded in a sensitizing environment, many owners change the base metal to A213 TP316LNM rather than relying on a perfect weld procedure alone to protect C ≤0.08% TP316N. Specify end preparation and surface finish on the tube PO when orbital or clean-service joins are planned.

Surface Finishes

Standard mill delivery for ASTM A213 TP316N is solution annealed and pickled, leaving a clean matte finish suitable for most boiler and heat-exchanger tube duty. Bright annealing under protective atmosphere produces a smoother reflective surface used on some clean-process and instrumentation tube lines and must be called out because it changes the heat-treatment route. Light polish or specified Ra on the bore or OD is a commercial or service-center operation on top of A213 product, not automatic with the grade stamp.

When a hygienic or fouling-sensitive exchanger specification quotes an Ra maximum on the bore, put it on the tube purchase order with its own acceptance language and sampling plan. SHH STEEL stencils grade and heat treatment as standard requirements; polish, special OD grind, and passivation after fabrication remain commercial extras unless the contract says otherwise. End preparation (plain, slightly beveled, or as needed for tube expanding) should be ordered together with finish so receiving inspection shares one acceptance language.

Inspection and Testing

Lot testing for ASTM A213 TP316N follows tension, hardness, flattening, and flaring under A213 / A1016. Chemistry verification must include the 0.10–0.16% nitrogen band, the 10.0–13.0% nickel window, and molybdenum 2.00–3.00%. NDE follows the ordered edition and purchaser supplements — hydrostatic testing or non-destructive electric testing of each length is the usual A213 path unless the purchase order states otherwise.

EN 10204 3.1 certificates from SHH STEEL report ladle chemistry with N and Mo, Table 4 tensile and hardness (80/35 ksi floors), and heat-treatment condition. When A262 Practice E is ordered under Footnote F / S4, those results appear as specified. Dual A213/SA-213 marking and third-party witness are available when written into the enquiry. A certificate missing nitrogen or molybdenum is not a complete TP316N release package.

Packaging and Shipping

TP316N tubes ship in capped or plugged bundles with weather protection matched to the route. Cut lengths for boiler and exchanger bundles are labeled by heat and size; export packing uses cases or steel-frame crates when required.

Marking includes ASTM A213, grade TP316N / UNS S31651, size, heat number, and SHH STEEL identification. Dual SA-213 marking appears only when the purchase order requests it. Packing lists track the same heat numbers shown on the EN 10204 3.1 certificates so nitrogen and molybdenum results stay tied to the shipped lengths.

Why Choose SHH STEEL

SHH STEEL treats ASTM A213 TP316N as a nitrogen-strengthened molybdenum specification product: N 0.10–0.16%, Ni 10.0–13.0%, Mo 2–3%, and Table 4 80/35 ksi floors are checked together before a heat is offered. Quotations state OD × wall / BWG, wall basis, finish route, A262 / Footnote F options, and whether dual A213/SA-213 marking is required.

We refuse nickname assemblies that stamp TP316 or TP304N as 316N without the missing nitrogen band, nickel ceiling, or molybdenum. EN 10204 3.1 documentation includes N and Mo. Compare sisters on the A213/A213M hub before freezing the exchanger tube list.

Supply Capability

SHH STEEL supplies ASTM A213 TP316N seamless stainless steel tube in cold-finished and hot-finished routes across the usual boiler, superheater, and heat-exchanger OD × wall / BWG band. Capability below is an enquiry range — not a frozen warehouse SKU or tonnage claim.

Capability SHH STEEL practice for TP316N
Product form Seamless cold-finished and hot-finished tube
Standards ASTM A213 / A213M; dual SA-213 when PO asks
Size band Typical within ~1/8 in. ID to 5 in. OD; other diameters by agreement
Wall basis Minimum wall or average wall as specified
Documentation EN 10204 3.1 MTC with N + Mo; A262 Practice E / third-party witness on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Stock / Available sizes

SHH STEEL quotes TP316N against a stock-and-mill enquiry range rather than a frozen SKU/tonnage list. Representative OD × wall / BWG combinations for boiler and heat-exchanger tube appear below.

Item Typical stock / enquiry range for TP316N
Outside diameter 19.05, 25.4, 31.8, 38.1, 42.4, 50.8, 60.3, 76.2 mm (and other boiler/HX ODs on enquiry; through the usual A213 ~5 in. [127 mm] band)
Wall / BWG BWG 10–18 class walls and metric min-wall equivalents; heavier walls by agreement
Common OD × wall examples 25.4 × 2.11 mm; 31.8 × 2.77 mm; 38.1 × 2.77 mm; 42.4 × 3.56 mm; 50.8 × 3.05 mm; 60.3 × 3.91 mm — illustrative, confirm min vs average wall
Length Cut lengths for boiler / exchanger bundles; bends and random mill lengths on enquiry
Special Non-standard OD/wall, bright anneal, dual A213/SA-213, A262 Practice E, third-party witness — confirm before heat reservation

Send OD × wall (or BWG), wall basis, finish route, quantity or cut list, marking (A213 or dual A213/SA-213), and N / A262 notes on one enquiry. We confirm C ≤0.08%, Cr 16–18% / Ni 10–13%, Mo 2.00–3.00%, N 0.10–0.16%, and Table 4 80/35 ksi without inventing fake warehouse codes. Sisters A213 TP316, A213 TP316LNM, and A213 TP304N sit on the same hub.

FAQ

Is ASTM A213 the same as ASME SA-213 for TP316N?
No. ASTM A213 / A213M is the ASTM International product specification for seamless boiler, superheater, and heat-exchanger tubes; ASME SA-213 / SA-213M is the separate ASME Code Book adoption. Dual-mark only when the purchase order asks for both names on the stencil and MTC. Chemistry and tensile floors align closely for a given referenced edition, but the standards remain independent documents.
Does ASTM A213 TP316N include welded or HCW tube?
No. ASTM A213 covers seamless boiler, superheater, and heat-exchanger tubes only. There is no WLD or HCW manufacturing-type letter under A213. Cold-finished versus hot-finished describes the seamless process route and dimensional tolerances — not a welded product form. Order welded stainless pipe under a different product standard when that form is required.
What is the chemistry of ASTM A213 TP316N?
Melting analysis for TP316N / UNS S31651 is C ≤0.08%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 16.0–18.0%, Ni 10.0–13.0%, Mo 2.00–3.00%, and N 0.10–0.16%. Confirm the ordered A213 edition. Nitrogen band, nickel ceiling at 13.0%, and molybdenum are all mandatory — none is optional on a 316N heat.
TP316N vs TP316 — what does the N add?
Both grades share Mo 2–3% and Cr 16–18. TP316 uses Ni 10–14% with nitrogen as a no-requirement ellipsis and Table 4 75/30 ksi. TP316N holds nitrogen in 0.10–0.16%, narrows nickel to 10.0–13.0%, and lifts tensile/yield to 80/35 ksi while keeping hardness max 192 HBW / 90 HRB. Order N when the datasheet needs the higher strength pair with molybdenum.
TP316N vs TP316LNM — when do I need low carbon?
Both share N 0.10–0.16%, Mo 2–3%, and Ni 10–13%. TP316N allows C ≤0.08% and holds Table 4 at 80/35 ksi. TP316LNM keeps C ≤0.035% (Footnote D to 0.040% on small OD / thin wall) and uses the 75/30 ksi floor. Choose LNM for as-welded IGC strategy with nitrogen and Mo; choose N when higher tensile is the priority and low carbon is not mandated.
Why is the nickel band 10.0–13.0% on TP316N instead of 10–14%?
The A213 stainless chemistry table for UNS S31651 prints nickel 10.0–13.0%, while TP316 / TP316L print 10.0–14.0%. A heat at 13.5% Ni can clear standard TP316 but fails TP316N. Check the nickel ceiling on every dual 316/316N candidate before assuming dual marking from nitrogen and molybdenum alone.
What does Footnote F mean for TP316N heat treatment?
Footnote F requires quench in water or other rapid cool at a rate sufficient to prevent carbide re-precipitation, demonstrable by A262 Practice E capability when that test is specified on the purchase order. The mill is not required to run Practice E unless S4 / the PO calls for it. Put Practice E on the enquiry when IGC demonstration is contractual.
Does Table 4 set a hardness limit for TP316N?
Yes. Table 4 lists hardness maximum 192 HBW / 200 HV or 90 HRB with 80 ksi tensile, 35 ksi yield, and 35% elongation. Hardness, nitrogen band, nickel window, and molybdenum all belong on the release package — none replaces the others for 316N boiler or HX tube.
What heat treatment does A213 require for TP316N?
Solution treatment at a minimum of 1900 °F [1040 °C], water quench or other rapid cool under Footnote F quench-capability language. Delivery is solution annealed and pickled unless bright anneal is agreed. No mandatory ASTM grain-size number appears for TP316N in the public heat-treatment table — put grain-size reporting on the PO only when the datasheet asks.
Minimum wall vs average wall for A213 TP316N — which should I specify?
Boiler and heat-exchanger datasheets almost always expect minimum wall. Average wall is allowed when the purchase order says so, with A1016/A1016M tolerances for that basis. State wall basis on the enquiry rather than relying on pipe schedule numbers as the primary A213 wall story.
Is TP316N a good choice for as-welded IGC-critical tube-to-tubesheet joints?
Often not as the first choice. Carbon up to 0.08% works against as-welded intergranular-corrosion strategy even when nitrogen raises strength. Many owners specify A213 TP316LNM for as-welded IGC duty with Mo and nitrogen, and reserve TP316N for lists that need the 80/35 ksi floor without an L-grade carbon mandate. Put A262 Practice E on the PO when IGC demonstration is contractual.
Can I dual-certify TP316N with TP316 on the same heat?
Yes when one heat simultaneously clears TP316’s C ≤0.08% and Ni 10–14% window, TP316N’s N 0.10–0.16% and Ni 10–13% ceiling, Mo 2–3% for both, TP316’s 75/30 ksi and TP316N’s 80/35 ksi floors, and hardness for both — and the purchase order asks for dual marking. Do not assume dual marking from a PMI gun that only reads Mo.

Conclusion

ASTM A213 TP316N / UNS S31651 is the nitrogen-strengthened molybdenum-bearing seamless stainless steel tube for boiler, superheater, and heat-exchanger service when Mo 2–3% and a mandatory N 0.10–0.16% band must deliver the Table 4 80/35 ksi floor. SHH STEEL supplies cold-finished and hot-finished seamless tube in the usual OD × wall / BWG band, solution annealed at 1900 °F [1040 °C] under Footnote F quench language, tested to Table 4 80/35 ksi and hardness limits, with nitrogen and molybdenum reported on EN 10204 3.1 certificates — dual SA-213 marking only when the purchase order asks.

Contact: admin@steelspecs.com

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X