ASME SA312 TP309S Stainless Steel Pipe | ASME SA312 Stainless Steel - SHH STEEL

ASME SA312 TP309S Stainless Steel Pipe | SA 312/SA 312M

ASME SA312 TP309S (UNS S30908) stainless steel pipe under SA-312/SA-312M (ASTM A312/A312M): seamless (SML), welded (WLD) and heavily cold-worked (HCW); Cr 22.0–24.0%, Ni 12.0–15.0%, C ≤0.08%, Mo ≤0.75%; Table 4 minima 75/30 ksi; solution annealed. SHH STEEL supplies with EN 10204 3.1 MTCs.
Grade
TP309S / UNS S30908
Standard
ASME SA312 / SA 312M (ASTM A312 / A312M)
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASME SA312 TP309S Stainless Steel Pipe

ASME SA-312/SA-312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. Grade TP309S is listed in Table 1 as UNS S30908. Commercially the same product may be called SA312 TP309S pipe, ASTM A312 TP309S pipe, A312 Grade TP309S, or 309S stainless steel pipe when the purchase order clearly references SA-312 or A312. For pressure piping and code work, cite the full grade designation, the UNS number, and the edition of the standard on the purchase order and on the mill test certificate—do not rely on a bare “309” or “309S” market label.

TP309S is a high-chromium, high-nickel heat-resisting austenitic grade—the standard “S” member of the 309 family. Table 1 locks carbon at ≤0.08%, sets chromium at 22.0–24.0% and nickel at 12.0–15.0%, and lists molybdenum as a residual ceiling of ≤0.75% (not an intentional alloying addition for chloride service). That chemistry supports the Table 4 tensile floor of 75 ksi min / 30 ksi min yield while raising oxidation resistance relative to classic 18-8 grades. It is not an H grade: Table 2 uses the default solution-annealing temperature of 1900 °F [1040 °C], Table 5 does not mandate grain-size control, and Table 6 lists no AWS filler class for TP309S (filler selection is by agreement). Clause 1.2 of SA-312 names TP309S as the parent of ASME SA312 TP309H Stainless Steel Pipe, ASME SA312 TP309Cb Stainless Steel Pipe, and ASME SA312 TP309HCb Stainless Steel Pipe.

SHH STEEL can supply ASME SA312 TP309S stainless steel pipe to the edition named on the enquiry, including seamless (SML), welded (WLD), and heavily cold-worked (HCW) routes; ASME B36.19 schedules and special OD/wall by agreement; EN 10204 3.1 mill test certificates; and dual SA-312/A312 marking when the heat analysis, heat treatment, mechanical tests, and marking satisfy both editions named on the purchase order. Confirm NPS, wall or schedule, finish, length practice, and any product-analysis or supplementary tests on enquiry.

Common commercial names and how they map to the ordered product are listed below—use the full SA-312/A312 designation on the purchase order rather than market shorthand alone.

  • ASME SA312 TP309S / SA-312 Grade TP309S — preferred marking language for ASME-code and dual-marked pipe
  • ASTM A312 TP309S — same grade tables for chemistry and tensile when the ASTM edition is referenced
  • UNS S30908 — unified numbering system identity used on MTCs and in cross-reference tables
  • 309S stainless steel pipe — market shorthand; confirm C ≤0.08%, Cr 22–24%, Ni 12–15%, and Mo ≤0.75% on the order

TP309S is not interchangeable with TP309H, TP309Cb, or TP310S on a shared “309” market label—each has its own Table 1 row and (where applicable) H-grade or columbium rules. Versus ASME SA312 TP304 Stainless Steel Pipe (Cr 18–20, Ni 8–11), the extra chromium and nickel raise oxidation resistance by roughly one temperature class. Versus ASME SA312 TP310S Stainless Steel Pipe (Cr 24–26, Ni 19–22), TP309S sits one step below in alloy content and is often the economic choice when 310-level chemistry is not required. Hub: ASME SA 312/SA 312M.

Manufacturing Types (SML / WLD / HCW)

ASME SA-312 defines three manufacturing routes that may be marked on finished TP309S pipe. Selecting the route is a purchase-order decision driven by design code, size range, wall thickness, and inspection preference. It does not change the Table 1 chemistry of Grade TP309S—melting must still meet C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, and Mo ≤0.75%.

  • Seamless (SML) — no welding at any stage of manufacture. Seamless is preferred for furnace tubes, heater piping, and pressure parts when the project specification excludes welded pipe, when thick walls favor seamless production, or when the piping class documentation is written around seamless product only.
  • Welded (WLD) — automatic welding without filler metal. The weld is finished so that the pipe meets dimensional and mechanical requirements after the final heat treatment required by SA-312. Welded product is widely used for ducts, recuperators, and common NPS/schedule combinations where the code accepts welded austenitic pipe.
  • Heavily cold-worked (HCW) — welded pipe that is cold worked to a reduction of area of wall and weld of at least 35% before the final anneal, again without filler metal in the longitudinal weld. HCW is ordered when the buyer wants the HCW marking and the process controls written into SA-312 for that route.

Each finished length is hydrostatically tested or nondestructively electrically tested. The manufacturer may choose the method unless the purchase order fixes one. Marking on the pipe typically includes the manufacturer, grade (TP309S), heat number, NPS or outside diameter and schedule or wall thickness, and the manufacturing type letters SML, WLD, or HCW. When comparing seamless versus welded TP309S offers, check manufacturing type and the hydro or NDE method on the mill test certificate—not only the grade stamp.

Because 309S is often specified for high-temperature duty by equipment builders who are not piping specialists, enquiries sometimes omit the manufacturing route or the edition of SA-312. Confirm route, edition, and any supplementary tests before placing a mill order so the certificate matches the design basis. Unlike the H grades, TP309S does not require heat-treatment lot marking under clause 17, though many buyers still request lot identification for traceability. Where a component is pressure retaining and sits in the creep range of the governing code, switch the conversation to ASME SA312 TP309H Stainless Steel Pipe before the mill melts the heat—oxidation-limited furnace parts and creep-range pressure parts are different selection problems.

Chemical Composition of SA312 TP309S

Two chemistry layers matter: melting (heat / ladle) analysis—mandatory per heat under ASME SA-312/ASTM A312 Table 1—and product analysis when ordered (Suppl. S1 / PO). SA-312/A312 defer product-analysis tolerances through ASTM A999/A999M §6.3 to ASTM A480/A480M Table A1.1. SHH STEEL reports actual ladle and, when ordered, product values—never unpublished tighter windows.

Melting analysis (heat / ladle analysis) — Table 1

Heat analysis for Grade TP309S / UNS S30908 from ASME SA-312/SA-312M (ASTM A312/A312M) Table 1 is summarized below. Values are maximum unless a range is shown; ellipses (…) mean no requirement in the ordered edition.

Element TP309S / UNS S30908 melting analysis
Carbon (C) ≤ 0.08
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 22.0 – 24.0
Nickel (Ni) 12.0 – 15.0
Molybdenum (Mo) ≤ 0.75
Nitrogen (N) … (no requirement)

Source: ASME SA-312/SA-312M ≡ ASTM A312/A312M Table 1 for Grade TP309S. Footnote B: maxima unless a range is shown; “…” means no requirement. Do not treat secondary catalog sheets as a substitute for the ordered edition.

Chromium drives oxidation resistance; nickel stabilizes austenite and supports toughness; the 0.08% carbon ceiling limits sensitization relative to unrestricted-carbon 309; molybdenum is a residual control, not an alloying addition for pitting resistance. The Mo ≤0.75% ceiling is why 309S is not a chloride-service substitute for TP316/TP316L.

Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1

When product analysis is ordered, finished-pipe chemistry shall meet Table 1 as modified by the product-analysis tolerances of ASTM A480/A480M Table A1.1 (via A999 §6.3). The verified product-analysis limits for TP309S are:

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.08 0.01 over ≤ 0.09
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 22.0 – 24.0 0.25 under / over 21.75 – 24.25
Nickel (Ni) 12.0 – 15.0 0.15 under / over 11.85 – 15.15
Molybdenum (Mo) ≤ 0.75 0.05 over ≤ 0.80

Chromium 22.0–24.0% sits in the A480 “over 20.00 to 30.00” row (0.25 each way). Nickel 12.0–15.0% is in the 10–20% row (0.15). Molybdenum ≤0.75% uses the “over 0.60 to 2.00” row (0.05 over).

309 family side by side (Table 1):

Element TP309S TP309H TP309Cb TP309HCb
C ≤ 0.08 0.04 – 0.10 ≤ 0.08 0.04 – 0.10
Cr 22.0 – 24.0 22.0 – 24.0 22.0 – 24.0 22.0 – 24.0
Ni 12.0 – 15.0 12.0 – 15.0 12.0 – 16.0 12.0 – 16.0
Mo ≤ 0.75 … ≤ 0.75 ≤ 0.75
Nb (Cb) … … 10×C min, 1.10 max 10×C min, 1.10 max

Versus TP309H: H grade adds a carbon floor (0.04–0.10%), Table 5 grain-size practice, and clause 6.2 reheat rules—do not treat TP309S as a free substitute for elevated-temperature creep service. Versus TP309Cb / TP309HCb: columbium (niobium) stabilization is required on those grades and is absent from TP309S. If an enquiry only says “309 stainless pipe,” confirm Table 1 limits, manufacturing type, and whether product analysis is required before rolling.

Mechanical Properties of SA312 TP309S

Tensile requirements for TP309S are given in ASME SA-312/SA-312M (ASTM A312/A312M) Table 4. Specimens and orientation follow the testing clauses of the standard and the referenced general requirements (A999/A999M as applicable).

Property TP309S requirement (Table 4)
Tensile strength, min 75 ksi [515 MPa]
Yield strength (0.2% offset), min 30 ksi [205 MPa]
Elongation in 2 in. or 50 mm (or 4D) 35% longitudinal / 25% transverse, min

These minima are the mandatory acceptance floor—the same 75/30 ksi used for TP304, TP309H, TP309Cb, TP309HCb, and TP310S. The grade is chosen for chemistry and high-temperature oxidation behaviour, not for higher room-temperature strength. Actual mill test certificate values are often higher; design calculations should still use Table 4 unless the purchase order states higher guaranteed values that the mill has accepted in writing. Cite UNS S30908 wherever allowable-stress tables are consulted so fabricators do not pull a sister-grade strength line from memory. ASME Section II Part D lists allowable stresses for S30908 where the part is pressure retaining.

Hardness: Table 4 does not list a hardness maximum for TP309S as a separately mandated acceptance item. If hardness matters for fabrication or end-user acceptance, state the limit on the purchase order and verify it on the MTC; otherwise omit hardness as a mandatory acceptance item. Grain size is not listed in Table 5 for TP309S. Flattening or bend and tension run on a lot basis; elevated-temperature tensile, creep, and rupture tests are purchase-order options—not part of base SA-312.

Hot strength and forming: 309-type alloys retain useful strength well into the furnace-temperature range. For sustained creep service within this family, prefer ASME SA312 TP309H Stainless Steel Pipe with its carbon floor and grain-size control. TP309S work hardens more than 304; bend radii should be generous, and trial bends are recommended for thin-wall furnace tubing. High chromium also raises the risk of sigma-phase formation after long exposure around 1100–1650 °F, which reduces room-temperature toughness—design and inspection of used parts should account for that.

Dimensions and Tolerances

Dimensional practice for austenitic stainless steel pipe ordered to SA-312 typically follows ASME B36.19 / B36.19M stainless-steel pipe schedules. Outside diameter and wall thickness are stated as NPS and schedule, or as OD and specified wall. Common schedules for TP309S enquiry include Schedule 5S, 10S, 40S, and 80S. Furnace and heater tubes are often ordered by OD and wall to the equipment drawing. Other walls and non-standard OD/wall combinations are available by agreement when both the mill and the order accept them.

Size coverage in commercial practice is summarized below. Confirm large NPS and heavy walls against mill capability for the chosen manufacturing type before you lock the purchase order.

  • NPS / DN: commonly from NPS 1/8 upward; large NPS and heavy walls depend on manufacturing type (SML versus WLD/HCW) and mill capability—confirm on enquiry
  • Schedules: 5S, 10S, 40S, 80S and special walls by agreement
  • Length: single random (SRL), double random (DRL), or fixed cut lengths as stated on the purchase order; NPS 1/8 to 8 commonly up to 24 ft unless agreed
  • Ends: plain end (PE), beveled end (BE), or other end preparations by agreement; jointers not permitted unless specified

Wall-thickness variation limits from SA-312 Table 3 (t/D = specified wall / ordered OD) are the acceptance bands used on mill test certificates and receiving inspection for TP309S:

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%

Source: SA-312 Table 3; outside diameter variations per A999/A999M. OD, wall, and length tolerances follow SA-312 via ASTM A999/A999M and the dimensional standard on the order. SHH STEEL quotes the applicable clause rather than dumping entire A999 tables. For radiant tubes and furnace rolls, specify straightness and ovality if needed—SA-312 covers wall and OD only. Thermal expansion of austenitic grades is high; supports and hangers must allow for growth. Confirm max wall and NPS near the edge of B36.19 practice before acceptance.

Equivalent Grades

Equivalence for TP309S must be stated carefully. Chemistry approximations across regional designations help material selection discussions; they are not automatic one-to-one substitutes for ASME pressure-code pipe without an approved material specification and design-code acceptance.

Designation Notes
ASME SA-312 / ASTM A312 Grade TP309S Governing pipe product standard for this article
UNS S30908 Unified number listed in Table 1
TP309H (UNS S30909) H grade for elevated temperature; different C band and grain-size practice
TP309Cb / TP309HCb Columbium (niobium) stabilized sisters; order the exact TP name on the PO
TP310S (UNS S31008) Higher Cr–Ni oxidation grade; not interchangeable on a “309” label
ASME SA-240 / A240 309S Plate counterpart (separate specification)
ASME SA-213 TP309S Boiler and heat-exchanger tube (separate specification)
EN 1.4833 (X12CrNi23-13) Commonly cited European counterpart; verify in the EN product standard
JIS SUS309STP Commonly cited Japanese pipe counterpart; verify against JIS

Within SA-312, do not interchange TP309S with TP309H, TP309Cb, or TP310S on a shared “309” market label—each has its own Table 1 row. Dual certification TP309S/TP309H is possible when a heat meets both carbon windows (0.04–0.08%), the H-grade anneal and grain-size rules, and both Table 4 floors (which are identical). Related pages: ASME SA312 TP309H Stainless Steel Pipe, ASME SA312 TP309Cb Stainless Steel Pipe, ASME SA312 TP309HCb Stainless Steel Pipe, ASME SA312 TP310S Stainless Steel Pipe, ASME SA312 TP304 Stainless Steel Pipe, ASME SA312 TP304H Stainless Steel Pipe. Hub: ASME SA 312/SA 312M.

Pressure-code caution: EN/JIS or proprietary approximations do not authorize B31 or Section VIII substitution without engineered approval and an accepted material specification written on the design documents. If the enquiry says only “309 pipe,” clarify whether the buyer needs TP309S, TP309H, or a dual-certified heat before the mill melts—creep service, grain-size reporting, and Mo residual requirements differ, and a wrong choice discovered after fabrication is expensive.

Heat Treatment and Delivery Condition

All pipe furnished to ASME SA-312 shall be heat treated. For TP309S and other grades that do not carry an individual temperature row in Table 2, the default minimum solution-annealing temperature is 1900 °F [1040 °C], followed by water quenching or another rapid cool sufficient to prevent harmful carbide reprecipitation. That Table 2 default is SHH STEEL’s delivery baseline unless the ordered edition of SA-312 states otherwise for the heat. Demonstrable freedom from harmful carbide precipitation by ASTM A262 Practice E applies when supplementary requirement S7 is ordered.

TP309S is not an H grade. Under ASME clause 6.2, seamless TP309S may be quenched directly after hot forming if its temperature is not below 1900 °F. The reheat-before-quench rule applies to H grades (including TP309H and TP309HCb) and to certain other listed UNS grades—not to TP309S. H-grade grain-size control and reheating notes written for TP309H do not change this S heat-treatment path. HCW cold reduction is done before final anneal; delivery remains the annealed condition—cold work is not a final hardness condition. Producers sometimes anneal 309S above the Table 2 minimum to ensure full solution of chromium carbides; if a project needs a specific anneal temperature, write it on the purchase order.

Commercial delivery condition for TP309S typically includes the following items unless the purchase order or ordered edition of SA-312 states otherwise:

  • Solution annealed to SA-312 Table 2 requirements for TP309S
  • Pickled and descaled, blasted and pickled, or bright annealed, as ordered (see Surface Finishes)
  • Straightened and cut to the ordered length practice
  • Hydrotested or NDE-tested per length as required by the standard and the purchase order
  • No grain-size requirement in Table 5 for TP309S

Corrosion Resistance

TP309S is selected primarily for high-temperature oxidation, not as a general aqueous corrosion grade. The 22–24% chromium band supports continuous service in air commonly quoted around 1900 °F [1040 °C] and intermittent service somewhat higher—those figures are producer guidance, not SA-312 values. SA-312 itself does not publish corrosion rates for TP309S; fitness for a given atmosphere, temperature, cycling schedule, and contaminant load must be validated against the project corrosion specification, not inferred from the grade name alone.

Versus TP304 / aqueous grades: In mild aqueous media TP309S behaves broadly like ASME SA312 TP304 Stainless Steel Pipe. Mo ≤0.75% does not provide 316-level chloride resistance—prefer ASME SA312 TP316L Stainless Steel Pipe or higher alloys when chlorides dominate. With C ≤0.08%, weld HAZs can still sensitize; for welded wet service after high-temperature exposure, review low-carbon or stabilized options such as ASME SA312 TP304L Stainless Steel Pipe.

Versus TP310S and sister 309 grades: ASME SA312 TP310S Stainless Steel Pipe generally gives a longer life at the top of the temperature range and in more aggressive oxidizing gases because of its higher chromium and nickel. TP309S is chosen when the milder alloy content is adequate and cost or nickel exposure matters. In sulfur-bearing gases the moderate nickel of 309S can be an advantage versus higher-nickel alloys that form low-melting nickel sulfides. Versus ASME SA312 TP309H Stainless Steel Pipe, the H grade is the SA-312 choice when creep rupture—not oxidation alone—governs life.

Other service notes: Carburization resistance is better than 304 but for strong carburizing atmospheres consider Si–Al grades or higher-nickel alloys. Long holds near 1100–1650 °F can form sigma phase and reduce toughness. Condensation during shutdowns—especially from sulfur-bearing fuels—can attack sensitized metal at low temperature; design for drainage and dry shutdown where possible. Proper pickling and passivation after fabrication help restore a clean passive surface; mill annealed-and-pickled pipe already carries a descaled surface.

Applications of SA312 TP309S Pipe

TP309S pipe is selected where austenitic stainless behavior, SA-312 product form, and high Cr–Ni oxidation chemistry are acceptable for the atmosphere and temperature—especially where furnace or heater duty matters more than aqueous chloride resistance. Typical application areas include:

Application area Typical use of TP309S pipe Selection note
Furnace tubes and muffles Oxidation resistance at furnace temperatures Support design to limit sag; oxidation allowance in wall
Heat-treatment equipment Hot-gas ducts, radiant sections, fixtures Check carburizing potential of the atmosphere
Refinery / petrochemical heaters Transfer lines and tube supports Prefer H grade if creep governs pressure parts
Dissimilar-metal transitions Pieces that absorb dilution when joining stainless to carbon steel Common companion to 309-type filler practice
Incinerators / waste-heat recovery Hot flue-gas ducts and headers Ash chemistry and chlorides matter
Cement and mineral processing Burner pipes and hot ducts Alkali attack possible—validate atmosphere

For creep-range pressure piping within this family, prefer ASME SA312 TP309H Stainless Steel Pipe. For higher oxidation margin, see ASME SA312 TP310S Stainless Steel Pipe. For welded corrosive aqueous service, see ASME SA312 TP304L Stainless Steel Pipe or ASME SA312 TP316L Stainless Steel Pipe. Match the grade family to atmosphere, temperature, and code needs first; commercial convenience is secondary to fitness for service.

Weldability

TP309S is generally weldable by common austenitic fusion processes with suitable heat input, interpass control, and joint cleanliness. It is also one of the most familiar filler chemistries for joining stainless to carbon steel, because the higher chromium and nickel tolerate dilution. Typical processes used on this grade include:

  • GTAW (TIG) — preferred for root passes and thin-wall pipe where weld metal cleanliness and heat-input control matter
  • GMAW (MIG) — productive for fill and cap passes on thicker walls when procedures are qualified
  • SMAW — widely used for field girth welds with coated austenitic electrodes selected by agreement
  • SAW / FCAW — used where procedure qualification and joint design support them
  • Automatic orbital or mechanized GTAW — common for repetitive high-integrity girth joints

Filler metal: SA-312 Table 6 lists TP309S, but the AWS A5.9 class and filler UNS columns show “…”—no classification is given. Filler selection is therefore by agreement and must be recorded on the WPS; seam repairs under clause 15 must identify the filler on the certificate. In fabrication practice, AWS A5.9 ER309 / ER309L consumables are the usual matching choice—that practice is industry guidance, not a Table 6 prescription. Note that mill longitudinal welds for WLD and HCW product are made without filler metal; Table 6 guidance applies to joining with filler, not to the mill autogenous weld.

Dissimilar joints commonly use 309-type fillers for stainless-to-carbon and stainless-to-low-alloy welds; 309 weld metal typically carries higher ferrite than 308, which aids hot-crack resistance. Moderate heat input and controlled interpass remain good practice. Keep joints clean of oil, paint, and carbon-steel contamination, and remove heat tint after welding when the end-user specification requires it. Girth welds follow the piping/vessel code (e.g. ASME B31 / Section IX) and are separate from mill hydro/NDE. Overlay and buttering with 309-type weld metal—common before applying a 308 or matching stainless overlay—is fabrication practice outside SA-312 but explains why 309 chemistry is so familiar to welding engineers. Sigma-embrittled or heavily oxidized service-exposed pipe may need solution annealing before repair welding; follow producer guidance.

Surface Finishes

Surface condition for SA312 TP309S pipe is stated on the purchase order. Typical mill finishes available from SHH STEEL supply include the following options:

  • Annealed and pickled (AP) — solution annealed, descaled in acid pickle or an equivalent process, producing a matte gray finish common for process and furnace pipe
  • Blasted and pickled — often used for heavy-wall seamless where scale removal benefits from blast first
  • Bright annealed (BA) — annealed in a protective atmosphere to a brighter surface where the order allows and mill capability exists for the size
  • As-annealed light oxide — sometimes accepted for furnace parts by agreement when the protective scale will form in service anyway
  • Mechanically polished — grit or Ra-controlled polish on OD and/or ID when ordered; polishing does not replace solution annealing
  • Bead-finished welded OD — weld bead rolled or ground flush as agreed for WLD/HCW product

Passivation after pickle or polish can be added when the end-user specification requires it. Pre-oxidation—heating new parts in air before exposure to process gas—is sometimes used to build an initial chromia scale; it is a user practice, not an SA-312 delivery condition. For high-temperature service the protective scale forms in operation; the delivered finish mainly affects inspection and cleanliness. Avoid marking materials with low-melting metals or high halide content. End preparation (plain or beveled) should be ordered together with finish so that bevel faces and ID cleanliness meet the same acceptance language.

Inspection and Testing

Base inspection and testing for SA-312 TP309S pipe combines chemistry, mechanical, and integrity checks. The following items form the usual acceptance package; supplementary requirements apply only when written on the purchase order.

  • Heat (melting) analysis — mandatory per heat against Table 1 for TP309S (UNS S30908), including C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, and Mo ≤0.75%
  • Product analysis — when ordered (Suppl. S1 / purchase-order language), using A480 Table A1.1 tolerances via A999 §6.3
  • Tension test — Table 4 tensile, yield, and elongation on a lot basis (75/30 ksi minima)
  • Flattening test — or alternate bend where the standard permits for certain welded pipe (typically on 5% of the lot)
  • Hydrostatic test or nondestructive electric test — each length; manufacturer’s option unless the order fixes the method
  • Visual and dimensional check — against ordered NPS/schedule or OD/wall and the applicable tolerance clauses

Mill test certificates: EN 10204 3.1 is the standard documentation package from SHH STEEL supply. EN 10204 3.2 or third-party witness (SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency) is arranged when specified and should be booked before final testing. Dual ASME SA-312 / ASTM A312 certification is available when chemistry, heat treatment, mechanical tests, and marking satisfy the edition(s) named on the order.

Optional / supplementary: S1 product analysis; S5 radiography for WLD pipe; S7 intergranular corrosion where aqueous service after welding is expected; elevated-temperature tensile on the PO; PMI (XRF quickly distinguishes 309 from 304 and 310); tighter straightness; special marking—only when listed on the PO. Keep heat numbers on cut pieces for MTC traceability. Receiving review should confirm chromium 22–24, nickel 12–15, carbon ≤0.08, molybdenum ≤0.75, tensile ≥75 ksi, yield ≥30 ksi, elongation, and hydro or NDE.

Packaging and Shipping

Export and domestic shipments of SA312 TP309S pipe are packed for handling and ocean or land transport. Typical packing practices from SHH STEEL supply include:

  • Seaworthy bundles — pipes strapped or cradled in bundles sized for container or break-bulk handling, with non-metallic separators where needed to protect finish; cradles for heavy lengths
  • End caps / protectors — plastic or metal caps on plain or beveled ends to reduce damage and contamination during transit
  • Marking — durable marking of grade (TP309S), UNS S30908 when required, heat number, size (NPS or OD × wall / schedule), manufacturing type (SML / WLD / HCW), test letters, and mill identity as required by SA-312 and the purchase order
  • Export packing — waterproof wrapping or desiccant as agreed for polished or sensitive finishes; container stuffing photos on request

Segregate TP309S from TP304, TP309H, and TP310S on the packing list and in the yard so stencil mix-ups do not travel with the shipment—PMI on receipt is a quick confirmation. Receiving inspectors should confirm that Mo is reported on the MTC (even as a residual) and that carbon is ≤0.08%; a heat with 0.09% carbon cannot be TP309S, though it might qualify as TP309H if the other H-grade rules are met. Long furnace tubes need intermediate supports in transit to prevent bending and ovality. Shipment docs typically include packing list, invoice, B/L or AWB, and MTC (3.1 or 3.2), plus origin/customs papers per Incoterms. State destination, packing preference, and extra marking at enquiry.

Why Choose SHH STEEL

SHH STEEL supplies specification-driven stainless plate and pipe. For ASME SA312 TP309S / UNS S30908 we quote against the edition you name, report the full Table 1 window on the MTC—including C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, and the Mo ≤0.75% residual—and keep heat identity unbroken from melt through finished length. Receiving inspection then clears the heat against Table 1 and Table 4 rather than against a vague “309S” catalog sheet. We also stay honest about Table 6: no AWS filler class is listed for TP309S, so filler selection stays by agreement on the WPS.

  • Specification fidelity — chemistry and tensile to SA-312/A312 Table 1 and Table 4 for TP309S (S30908), not unpublished tighter windows
  • Mill resources — SML, WLD, and HCW from qualified stainless pipe mills with heat traceability; cutting and beveling on confirmed orders
  • Documentation — EN 10204 3.1 MTCs standard; 3.2 or third-party inspection on request
  • Dual marking — ASME SA-312 and ASTM A312 when the heat and tests meet both requirements you name; dual 309S/309H when carbon, anneal, and grain-size rules allow
  • Related grades — sister 309-family and 310S SA-312 grades when projects buy matched high-temperature packages
  • Export packing — seaworthy bundles, end protectors, and durable grade/heat/size/type marking

Quotations follow your purchase-order language for edition year, manufacturing type, size, finish, and any supplementary tests you name. Ask for dual 309S/309H options when the design temperature is near the creep boundary. Grade hub: ASME SA 312/SA 312M.

Supply Capability

SHH STEEL can supply ASME SA312 TP309S / UNS S30908 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.

Item SHH STEEL capability for TP309S
Standard ASME SA-312/SA-312M and/or ASTM A312/A312M Grade TP309S (UNS S30908)
Manufacturing types SML, WLD, HCW
Size NPS 1/8 and up per ASME B36.19; special OD/wall by agreement
Schedules 5S, 10S, 40S, 80S and non-standard walls
Length SRL, DRL, or cut-to-length
Finish Annealed and pickled; blasted and pickled; bright annealed or polished by agreement
Testing Tension, flattening/bend, hydro or NDE per length; supplementary tests on order
Documents EN 10204 3.1; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

TP309S is a regular mill grade. Common sizes are often available from stock or short mill runs; heavy walls and special OD/wall combinations are mill-order items with longer lead times. Stock moves with mill rolling cycles. Enquiries should state the SA-312 edition, SML/WLD/HCW, NPS or OD×wall, length practice, finish, and any product-analysis or 3.2 requirements so mill slots align with your need date. Cut lengths, beveling, and packing-list marking are available on confirmed orders. If the design temperature sits in the creep range, ask whether TP309H (or dual 309S/309H) is preferred before finalising the PO—changing after mill production is costly.

FAQ

Is ASME SA312 the same as ASTM A312?
For chemistry (Table 1), tensile (Table 4), manufacturing types, and most testing language, ASME SA-312/SA-312M matches ASTM A312/A312M of the referenced edition. Dual SA312/A312 marking is common when ordered. Name both editions on the purchase order and mill test certificate so inspectors can verify the heat against the exact books you cited—do not assume a bare market grade stamp covers dual certification.
What is the UNS number for TP309S?
Table 1 lists TP309S as UNS S30908. Use that UNS on the purchase order, stencil, and MTC so chemistry and tensile rows stay unambiguous. When the project mixes plate and pipe, carry the same UNS language across forms, but still order pipe to SA-312/A312—not to the plate specification alone.
TP309S vs TP309H — which should I order?
TP309H adds C 0.04–0.10%, Table 5 grain size, and clause 6.2 reheat; TP309S has C ≤0.08% without those H mandates. Both use 75/30 ksi floors. Put the design-code grade and UNS on the datasheet and purchase order before you compare price—switching to TP309H after fabrication drawings are frozen usually means a material change notice, not a free mill substitution.
TP309S vs TP310S — which should I order?
TP310S has higher Cr (24–26%) and Ni (19–22%) for stronger oxidation resistance; TP309S uses Cr 22–24% and Ni 12–15%. Put the design-code grade and UNS on the datasheet and purchase order before you compare price—switching to TP310S after fabrication drawings are frozen usually means a material change notice, not a free mill substitution.
Seamless vs welded TP309S — which is better?
Neither is universally better. Choose the manufacturing type your design code and datasheet allow; both are legitimate SA-312 forms when tested to the standard. State SML, WLD, or HCW on the purchase order and confirm the same letters on the pipe marking and MTC—mixing offers that differ only in manufacturing type is a common bid-evaluation trap.
Can you dual-certify SA312 / A312 TP309S?
Yes, when heat analysis, heat treatment, mechanical tests, and marking meet both editions named on the order. Write the ASME and ASTM edition years on the PO, and require the MTC to reference both books so receiving inspection can clear the heat without a second paperwork chase after shipment.
Hydrostatic test vs NDE — which do I get?
Each length is hydrotested or nondestructively electrically tested. Manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification locks one method, state it on the PO and verify the chosen test appears on the MTC for every length—silent mill option is not the same as an approved project method.
What heat treatment / anneal temperature applies to TP309S?
Table 2 default 1900 °F [1040 °C]. Clause 6.2 reheat does not apply to TP309S. Delivery remains the solution-annealed condition required by SA-312 unless the edition and PO state otherwise. Cite the ordered edition’s Table 2 row on the enquiry so the mill does not apply a neighboring grade’s anneal practice by habit.
What Table 1 chemistry defines TP309S?
Table 1: C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, Mo ≤0.75% (UNS S30908). Values are melting-analysis limits from the ordered edition—do not invent tighter catalog windows. When product analysis is needed, order it explicitly (Suppl. S1 / PO language) rather than assuming ladle values alone will satisfy receiving inspection.
What are the Table 4 tensile requirements for TP309S?
Table 4 minima are 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield (elongation per the standard’s Table 4 row). Actual MTC values are often higher; design still uses Table 4 unless the PO states higher guarantees. Record the Table 4 row on the datasheet so fabricators do not substitute a sister-grade strength line from memory.
What filler metal should I use to weld TP309S pipe?
Table 6 lists TP309S with “…” in the AWS class column—filler selection is by agreement, not a mandated ER309 prescription. Mill WLD/HCW longitudinal welds use no filler. In fabrication practice ER309/ER309L are the usual matching choice; freeze the AWS (or EN) class on the WPS/PQR before production welds, and remember Table 6 guidance applies to joining with filler, not to the mill autogenous seam.
Does TP309S have a molybdenum requirement?
Yes. Table 1 lists Mo ≤0.75% for TP309S as a residual ceiling—not an intentional alloying addition for chloride pitting resistance. Confirm Mo on the heat analysis against the ordered edition of SA-312/A312, and put the same wording on the purchase order and MTC review checklist so receiving inspection does not invent a tighter window or treat 309S as a 316 substitute.

Conclusion

ASME SA312 TP309S (UNS S30908) is the standard high-chromium, high-nickel heat-resisting austenitic pipe grade in SA-312 for high-temperature oxidizing service when C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, and Mo ≤0.75% are required. Table 4 minima are 75/30 ksi; heat treatment follows the Table 2 default 1900 °F [1040 °C]; Table 6 lists no AWS filler class (filler by agreement); it is not an H grade, and creep-range pressure parts usually belong on TP309H instead. Order the manufacturing type (SML/WLD/HCW), schedule or wall, finish, and any product analysis or supplementary tests explicitly. For stock checks, mill certificates, or dual SA-312/A312 supply questions, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category on steelspecs.com.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X