ASME SA312 TP304L Stainless Steel Pipe | ASME SA312 Stainless Steel - SHH STEEL

ASME SA312 TP304L Stainless Steel Pipe | SA 312/SA 312M

ASME SA312 TP304L / UNS S30403 low-carbon stainless steel pipe in SML, WLD and HCW, with C ≤0.035%, Cr 18.0–20.0% and Ni 8.0–13.0%, a 70/25 ksi Table 4 floor and a 1900 °F solution anneal, supplied by SHH STEEL with EN 10204 3.1 MTCs and dual 304/304L on qualifying heats.
Grade
TP304L / UNS S30403
Standard
ASME SA312 / SA 312M (ASTM A312 / A312M)
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Dimensions
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASME SA312 TP304L Stainless Steel Pipe

ASME SA-312/SA-312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe for high-temperature and general corrosive service, and it is the ASME Code adoption of ASTM A312/A312M. TP304L / UNS S30403 is the low-carbon member of the 18-8 family, and in many plants it has quietly replaced plain TP304 as the default stainless pipe because welded lines no longer need special care to avoid sensitization. The purchase order and certificate should still name SA-312 or A312, the edition, and the full grade, not just “304L”.

Table 1 sets C ≤0.035%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 18.0–20.0%, and Ni 8.0–13.0%, with no molybdenum or nitrogen requirement. Footnote D allows carbon up to 0.040% on small-diameter or light-wall pipe where the mill needs it. Table 4 sets 70 ksi [485 MPa] tensile and 25 ksi [170 MPa] yield minimum with 35% longitudinal / 25% transverse elongation, lower than TP304 because the carbon is lower. Table 2 applies the default 1900 °F [1040 °C] minimum anneal, and Table 6 lists ER308L as the filler.

SHH STEEL can supply ASME SA312 TP304L stainless steel pipe to the edition named on the enquiry, in seamless (SML), welded (WLD), and heavily cold-worked (HCW) form. We quote ASME B36.19 schedules and special OD/wall by agreement, ship with EN 10204 3.1 mill test certificates that show the actual carbon against the 0.035% ceiling, and offer dual SA-312/A312 marking and dual TP304/TP304L certification when the heat meets both rows. Please confirm NPS, wall or schedule, finish, length practice, and any intergranular or product-analysis tests when you enquire.

The names below are the ones buyers commonly use, and they map to the ordered product as shown. Put both TP304L and S30403 on the order so the low-carbon requirement survives every handover between purchasing, the mill, and receiving inspection.

  • ASME SA312 TP304L / UNS S30403 — preferred marking language for ASME-code and dual-marked pipe
  • ASTM A312 TP304L — same grade tables when the ASTM edition is referenced
  • “304L” or “304/304L” pipe — market shorthand; the dual form is only valid if the MTC certifies both grades
  • EN 1.4306 / 1.4307, JIS SUS304L — approximate regional equivalents for discussion only

Sister grades buyers compare with TP304L include ASME SA312 TP304 Stainless Steel Pipe (C ≤0.08% and 75/30 ksi), ASME SA312 TP304LN Stainless Steel Pipe (low carbon plus nitrogen for 75/30 ksi), ASME SA312 TP304H Stainless Steel Pipe for creep service, and ASME SA312 TP316L Stainless Steel Pipe when chlorides call for molybdenum. Grade hub: ASME SA 312/SA 312M.

Manufacturing Types (SML / WLD / HCW)

ASME SA-312 recognizes three manufacturing routes for TP304L pipe, and the route is a purchase-order decision driven by the design code, the size range, wall thickness, and how the owner wants the pipe inspected. The route never changes the chemistry: whichever way the pipe is made, the heat must still meet C ≤0.035% (Footnote D: up to 0.040% for small OD / light wall), Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 18.0–20.0%, and Ni 8.0–13.0%, and every length must still go through the solution anneal at 1900 °F [1040 °C] minimum before it is released.

  • Seamless (SML) — no welding at any stage. Seamless is preferred for heavy walls, high-pressure lines, and piping classes written around seamless product only; it still has to be solution annealed before release.
  • Welded (WLD) — automatic welding without filler metal, with the weld finished so the pipe meets dimensional and mechanical requirements after the final heat treatment. The strip or plate heat must itself carry the full TP304L chemistry, so ask for the coil or plate heat number on the certificate.
  • Heavily cold-worked (HCW) — welded pipe cold worked to at least 35% reduction of wall and weld before the final anneal, again without filler in the longitudinal seam, with the weld radiographed before cold work. Order HCW when the project specifically wants that marking and the process controls SA-312 writes around it.

Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test in place of the hydrotest, and lots for mechanical testing follow clause 11.1. Welded TP304L is the commonest form in hygienic and chemical plants, because the low carbon protects both the mill seam and site girth welds from sensitization; check the SML, WLD, or HCW letters and the test method on the certificate when comparing offers.

TP304L is stocked as widely as TP304, and most stock is in fact dual-certified TP304/TP304L. Heavy-wall seamless and special OD × wall sizes are mill-order items, so give us the route, size, wall, edition year, and whether dual marking is acceptable, and we will tell you honestly whether stock or a mill run fits your need date.

Chemical Composition of SA312 TP304L

Two chemistry layers matter for TP304L. The melting (heat or ladle) analysis is mandatory for every heat under SA-312/A312 Table 1, while product analysis on finished pipe applies only when it is ordered through Supplementary Requirement S1 or purchase-order wording. Product tolerances are not printed in SA-312 itself; they come through ASTM A999/A999M §6.3 from ASTM A480/A480M Table A1.1. SHH STEEL reports the actual ladle values and, when ordered, the product values, and never quotes tighter catalogue windows that the standard does not publish.

The tables below reproduce the Table 1 heat analysis for TP304L and the product-analysis limits that result from applying the A480 Table A1.1 tolerances. Values are maximum unless a range is shown, and an ellipsis (…) means the ordered edition sets no requirement for that element, so it need not be determined or reported on the certificate.

Melting analysis (heat / ladle analysis) — Table 1

Element TP304L (UNS S30403) melting analysis
Carbon (C) ≤ 0.035 D
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 18.0 – 20.0
Nickel (Ni) 8.0 – 13.0
Molybdenum (Mo) … (no requirement)
Nitrogen (N) … (no requirement)

Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.035 0.01 over ≤ 0.045
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 18.0 – 20.0 0.20 under / over 17.80 – 20.20
Nickel (Ni) 8.0 – 13.0 0.10 under / 0.15 over 7.90 – 13.15

Carbon at 0.035% maximum is the defining element and the first value to check on receipt. Low carbon keeps chromium carbides from forming at grain boundaries in the weld heat-affected zone, which is what protects welded TP304L from intergranular attack without a post-weld anneal. Nickel runs up to 13.0%, wider than the 8.0–11.0% of ASME SA312 TP304 Stainless Steel Pipe, which gives the mill room to balance the austenite after carbon (an austenite former) has been taken out. Footnote D lets small-OD or light-wall pipe reach 0.040% carbon, so if your project needs 0.035% across all sizes, write that on the order.

On product analysis the finished pipe may read up to C 0.045%, Mn 2.04%, P 0.055%, S 0.035%, and Si 1.05%, with Cr 17.80–20.20% and Ni 7.90–13.15%. That product carbon limit is based on the 0.035% Table 1 ceiling plus the 0.01 tolerance; the Footnote D 0.040% case is not separately tabulated here, so agree the acceptance basis on the purchase order if it matters to your inspection plan.

Mechanical Properties of SA312 TP304L

Room-temperature tensile requirements for TP304L come from SA-312 Table 4 and are summarized below. These are minimum release values for the lot, not typical values, and design allowables must always be taken from the governing code tables for UNS S30403 rather than from a neighbouring grade.

Property TP304L requirement (Table 4)
Tensile strength, min 70 ksi [485 MPa]
Yield strength (0.2% offset), min 25 ksi [170 MPa]
Elongation in 2 in. or 50 mm (or 4D) 35% longitudinal / 25% transverse, min

The 70/25 ksi floor is lower than TP304 because carbon contributes strength and TP304L has less of it. Designers using TP304L allowables must take them from the code tables for UNS S30403, not from TP304. Table 4 does not list a hardness maximum for TP304L, so state any hardness requirement on the purchase order if your fabrication needs one, and we will have it reported on the certificate.

Dual-certified TP304/TP304L pipe meets the higher TP304 floor of 75/30 ksi and the TP304L carbon limit at the same time, which is why many owners standardize on it: designers get TP304 allowables and welders get TP304L corrosion behaviour. If you need more strength with low carbon as a single grade, ASME SA312 TP304LN Stainless Steel Pipe uses nitrogen to reach 75/30 ksi.

Dimensions and Tolerances

Dimensional supply for SA312 TP304L pipe follows ASME B36.19 schedules for the common NPS and schedule combinations, with special OD and wall available by agreement when a project needs a section the schedules do not cover. Outside-diameter variations follow ASTM A999/A999M, and wall-thickness variations follow SA-312 Table 3 as summarized below. State on the purchase order whether wall is nominal or minimum (Supplementary S8), because the two readings produce different pipe from the same size line.

NPS designator Over Under
1/8 – 2-1/2, all t/D 20.0% 12.5%
3 – 18, t/D ≤ 5% 22.5% 12.5%
3 – 18, t/D > 5% 15.0% 12.5%
≥ 20 welded 17.5% 12.5%
≥ 20 seamless, t/D ≤ 5% 22.5% 12.5%
≥ 20 seamless, t/D > 5% 15.0% 12.5%

Source: SA-312 Table 3; outside diameter variations per A999/A999M.

  • Lengths — single random, double random, or cut-to-length on order
  • Cut lengths — typically no more than 1/4 in. [6 mm] over the ordered length unless the PO states a tighter band
  • Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen

Many chemical, food, and pharmaceutical buyers order by OD × wall rather than NPS and schedule, which is fine as long as the enquiry says so clearly. Straightness, end finish, and length tolerance should be written into export orders so receiving inspection has an agreed acceptance basis instead of arguing after arrival. On thin schedules with threaded or socket-weld ends, check that the remaining wall is still adequate after the 12.5% under-tolerance. Jointers are not permitted unless the purchase order allows them, so cut-to-length programmes should include an allowance for fit-up scrap rather than expecting the mill to ship short pieces.

Equivalent Grades

TP304L / UNS S30403 has approximate equivalents in European and Japanese standards that buyers use when comparing old datasheets and offers. Equivalence is a materials discussion, not a substitution approval, so pressure-code pipe still has to be ordered and certified to SA-312 or A312.

Designation Notes
ASME SA-312 / ASTM A312 Grade TP304L Governing pipe product standard for this article
UNS S30403 Unified number listed in Table 1
EN 1.4306 / 1.4307 (X2CrNi19-11 / X2CrNi18-9) Approximate wrought low-carbon stainless designations; EN tube/pipe product forms are ordered under the relevant EN product specs, not by EN number alone on an SA-312 MTC
JIS SUS304L Approximate Japanese grade name; confirm the Japanese pipe/tube product standard when ordering JIS product

EN 1.4306 and 1.4307 and JIS SUS304L are approximate low-carbon wrought designations, and which EN number fits a project is a project-specific decision. None of them authorizes B31 or Section VIII substitution without engineered approval. Within SA-312, ASME SA312 TP304 Stainless Steel Pipe and ASME SA312 TP304LN Stainless Steel Pipe have their own carbon and tensile rows, and dual TP304/TP304L is valid only when the MTC certifies both. Related: ASME SA312 TP316L Stainless Steel Pipe.

Heat Treatment and Delivery Condition

All pipe furnished to SA-312 has to be heat treated. TP304L is not individually listed in Table 2, so it takes the default solution anneal at 1900 °F [1040 °C] minimum, followed by water quenching or another rapid cool. The low carbon means TP304L is far more forgiving of slow cooling than TP304, but the anneal and quench are still mandatory, and the anneal statement belongs on the certificate for every lot.

Seamless pipe may be quenched directly after hot forming when the edition allows it and the finishing temperature is not below the minimum anneal. HCW cold reduction happens before the final anneal, so delivery is always the annealed condition. In practice the pipe ships solution annealed, pickled or bright annealed as ordered, straightened, cut to the ordered length practice, and hydrotested or NDE-tested on every length. Post-weld annealing of TP304L fabrications is rarely needed for corrosion reasons, which is much of the grade’s appeal.

Corrosion Resistance

SA-312 has no corrosion table, so this section is engineering commentary rather than a specification requirement. In the parent metal TP304L behaves like TP304: good in oxidizing aqueous media, atmospheric exposure, food contact, and mild chemicals. The difference shows up after welding, where the low carbon keeps the heat-affected zone free of the chromium-carbide networks that make welded TP304 vulnerable to intergranular attack.

  • As-welded corrosion — the main reason to buy TP304L; S7 (A262 Practice E) can be ordered as proof
  • Chlorides — still no molybdenum, so ASME SA312 TP316L Stainless Steel Pipe is the better choice for seawater, brine, or heavy chloride duty
  • Chloride stress corrosion cracking — similar susceptibility to other 300-series grades in warm chloride water
  • Elevated temperature — low carbon reduces strength in the creep range, where ASME SA312 TP304H Stainless Steel Pipe is the correct grade

Most field failures of 304L lines trace back to deposits, stagnant pockets, and contamination rather than the grade itself, so drainage, cleanliness, and post-weld cleaning matter as much as the carbon number. Site welds and ground areas should be cleaned and passivated when the end-user specification asks for it, and carbon-steel tools and slings should be kept away from the pipe during fabrication.

Applications of SA312 TP304L Pipe

Applications for TP304L pipe follow from its low carbon, which makes welded systems reliable without post-weld annealing. The table below summarizes where buyers typically specify the grade and the selection points we see most often on enquiries.

Application area Typical use of TP304L pipe Selection note
Chemical and process piping Welded transfer lines for mild corrosive media ordered to SA-312 Confirm fluid compatibility; prefer TP316L if chlorides dominate
Food, beverage, and dairy Hygienic welded lines where 304L stainless is accepted Follow hygiene finish and welding procedure requirements
Pharmaceutical / biotech Process and utility stainless lines ordered as SA-312 product State Ra/polish and documentation on the enquiry when required
Power and utility Condensate, feedwater auxiliary, and general plant stainless piping Dual SA312/A312 marking often requested for code work
Cryogenic service Liquefied-gas transfer where austenitic toughness is required Confirm low-temperature code acceptance for the grade
Welded assemblies Skids and spool pieces where as-welded sensitization resistance is specified Low-carbon chemistry is the primary reason to choose TP304L over TP304

Typical buyers include chemical and fertilizer plants, food, dairy, brewery, and pharmaceutical producers, water treatment, and cryogenic equipment builders, all of whom weld a great deal of pipe in the field. Where chlorides dominate, move to ASME SA312 TP316L Stainless Steel Pipe; where the design wants TP304 allowables, order dual TP304/TP304L or ASME SA312 TP304LN Stainless Steel Pipe; and where the line runs in the creep range, use ASME SA312 TP304H Stainless Steel Pipe instead of a low-carbon grade.

Weldability

TP304L is about as weld-friendly as stainless pipe gets, and it is often chosen precisely because it can be welded in the field without post-weld heat treatment. SA-312 Table 6 lists AWS A5.9 ER308L (UNS S30883 / W30843) as the filler for TP304L, and ER308L should be recorded on the WPS and PQR so the weld deposit keeps the same low-carbon protection as the pipe. Using standard ER308 on low-carbon pipe gives away part of the reason for buying TP304L.

  • GTAW root passes — with back-purge on thin wall and hygienic lines
  • GMAW or SMAW fill — on heavier walls once the procedure is qualified
  • Orbital GTAW — common for pharmaceutical and food girth welds
  • Clean joints — free of oil, paint, and carbon-steel contamination before welding

Mill longitudinal welds on WLD and HCW pipe are made without filler, so Table 6 guidance applies to repairs and fabrication joints. Girth-weld NDE follows the piping or vessel code and is separate from the hydro or electric test the mill applies to each length. Heat input should still be sensible, because low carbon reduces but does not remove every welding risk, such as distortion and heat tint that has to be cleaned off afterwards.

Surface Finishes

Surface condition for SA312 TP304L pipe should be stated on the purchase order rather than left to mill default. For stainless pipe, embedded free iron, residual scale, and chloride-bearing residues are where corrosion starts, so the finish is part of the material performance and not just appearance. The finishes we regularly quote for this grade are listed below.

  • Annealed and pickled (AP) — solution annealed at 1900 °F [1040 °C] minimum, then descaled in acid pickle or an equivalent process to a matte grey finish; the standard choice for process pipe
  • Blasted and pickled — common on heavy-wall seamless where blasting first makes scale removal more reliable
  • Bright annealed (BA) — annealed in a protective atmosphere where mill capability exists for the size; the anneal temperature still has to meet the Table 2 practice for TP304L
  • Mechanically polished — OD and/or ID polish to an agreed grit or Ra when ordered; polishing never replaces the solution anneal
  • Bead-finished welded OD — weld bead rolled or ground flush as agreed on WLD and HCW product

For TP304L, annealed and pickled covers most process work, while dairy, brewery, and pharmaceutical lines often call for bright annealed or polished pipe with a stated Ra; we will not imply a hygienic finish on standard AP pipe unless the order says so. Passivation after pickling or polishing can be added when the end-user specification calls for it, even though SA-312 itself does not require it. If the project bans chloride-bearing marking inks, say so on the order; otherwise the mill will apply its normal stencil practice and ship its default AP finish.

Inspection and Testing

The base acceptance package for SA-312 TP304L pipe combines chemistry, tensile testing, heat-treatment evidence, and a pressure or electrical integrity test on every length. The items below make up the usual package; supplementary requirements and project corrosion tests only apply when they are written on the purchase order.

  • Heat (melting) analysis — mandatory per heat against Table 1 for TP304L: C ≤0.035% (Footnote D: up to 0.040% for small OD / light wall), Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 18.0–20.0%, and Ni 8.0–13.0%
  • Product analysis — when ordered (Suppl. S1 or PO wording), using A480 Table A1.1 tolerances via A999 §6.3
  • Tension test — 70 ksi [485 MPa] tensile and 25 ksi [170 MPa] yield minimum, plus 35% L / 25% T elongation on a lot basis
  • Flattening test — or the alternate bend test where the standard permits
  • Hydrostatic or nondestructive electric test — every length; manufacturer’s option unless the order fixes the method
  • Visual and dimensional check — against ordered NPS/schedule or OD × wall, with TP304L (UNS S30403) on every stencil

Mill test certificates: EN 10204 3.1 is the standard documentation from SHH STEEL supply. For TP304L the certificate reports the full Table 1 chemistry with carbon shown against the 0.035% ceiling, the 70/25 ksi tensile results with 35%/25% elongation, the hydro or NDE method, and the 1900 °F anneal statement. EN 10204 3.2 or third-party witness by SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency is arranged when specified, and it should be booked before final testing rather than after the heat has been released. Dual ASME SA-312 / ASTM A312 certification is available when chemistry, heat treatment, mechanical tests, and marking satisfy both editions named on the order.

Option Purpose
S1 product analysis Confirms chemistry on finished pipe
S5 radiography Weld integrity on WLD pipe
S7 intergranular corrosion A262 Practice E after sensitizing treatment
S8 minimum wall Wall interpreted as minimum rather than nominal
S9 weld decay Compares weld and base-metal loss rates

Receiving review should confirm C ≤0.035% (or the Footnote D 0.040% where it applies and is accepted), Cr 18.0–20.0%, Ni 8.0–13.0%, the 70/25 ksi tensile results, the anneal statement, and the test method. Dual TP304/TP304L pipe should show both grades on the stencil and the MTC with tensile results at or above 75/30 ksi. PMI guns cannot read carbon, so the certified analysis or an OES test is the only way to confirm the L grade.

Packaging and Shipping

Export and domestic shipments of SA312 TP304L pipe are packed for handling and for ocean or land transport. The packing we normally apply is summarized below, and anything beyond it can be agreed on the order.

  • Seaworthy bundles — pipes strapped or cradled in bundles sized for container or break-bulk handling, with non-metallic separators where the finish needs protecting
  • End caps — plastic or metal caps on plain or beveled ends to keep out damage and contamination in transit
  • Marking — specification, grade (TP304L (UNS S30403)), heat number, size, manufacturing type (SML / WLD / HCW), test letters, and mill identity as SA-312 and the purchase order require
  • Export protection — waterproof wrapping or desiccant as agreed for polished or bright-annealed finishes, with low-chloride inks on request

Segregate TP304L from ASME SA312 TP304 Stainless Steel Pipe and ASME SA312 TP316L Stainless Steel Pipe bundles on the packing list and in the yard, because these grades look identical and carbon cannot be checked with a handheld PMI gun. Use separate bundles and distinct tags on mixed shipments, and have receiving check stencil heat numbers against the MTC. Keep interiors dry and capped so chloride-bearing moisture cannot stain or pit the surface before installation. Shipping documents normally include the packing list, invoice, bill of lading or air waybill, and the 3.1 or 3.2 MTC with full Table 1 chemistry, plus origin and customs papers to suit the agreed Incoterms.

Why Choose SHH STEEL

SHH STEEL supplies specification-driven stainless plate and pipe, and for SA312 TP304L we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 chemistry on the MTC with the actual carbon shown against the 0.035% ceiling, and we quote against the edition you name rather than a generic “304L” catalogue sheet. Heat identity stays unbroken from the melt to the finished length, so receiving inspection can clear each heat against Table 1 and Table 4 without chasing paperwork after the pipe has arrived.

The commonest problems we see with TP304L are certificates that do not show carbon clearly, stencils that read only “304”, and dual-marked stock whose tensile results do not actually meet the TP304 floor. We check supplier certificates before shipment so those issues are caught at the mill rather than at the fabricator, and we tell you plainly whether a stock heat qualifies for dual marking.

  • Specification fidelity — chemistry and tensile to SA-312/A312 Table 1 and Table 4 for TP304L (S30403); C ≤0.035% reported; 1900 °F anneal stated; dual TP304/TP304L on qualifying heats
  • Mill resources — SML, WLD, and HCW from qualified stainless pipe mills with heat traceability; cutting and beveling on confirmed orders
  • Documentation — EN 10204 3.1 MTCs as standard with full Table 1 chemistry; 3.2 or third-party inspection on request
  • Dual marking — ASME SA-312 and ASTM A312 when the heat and tests meet both editions you name
  • Related grades — ASME SA312 TP304 Stainless Steel Pipe, ASME SA312 TP304LN Stainless Steel Pipe, ASME SA312 TP316L Stainless Steel Pipe, and ASME SA312 TP304H Stainless Steel Pipe when a project buys a matched package
  • Export packing — seaworthy bundles, end protectors, and durable grade, heat, size, and type marking

Quotations follow your purchase-order language for edition year, manufacturing type, size, wall, finish, and any supplementary tests you name (S1, S5, S7, S8, S9). If the same project also needs plate or fittings, ask for coordinated heats so the chemistry lines up across product forms. Grade hub: ASME SA 312/SA 312M.

Supply Capability

SHH STEEL can supply ASME SA312 TP304L stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.

Item SHH STEEL capability for TP304L
Standard ASME SA-312/SA-312M and/or ASTM A312/A312M Grade TP304L / UNS S30403
Manufacturing types SML, WLD, HCW
Size NPS 1/8 and up per ASME B36.19; special OD/wall by agreement
Schedules 5S, 10S, 40S, 80S and non-standard walls
Length SRL, DRL, or cut-to-length
Finish Annealed and pickled; blasted and pickled; bright annealed or polished by agreement
Testing Tension (70/25 ksi), flattening/bend, hydro or NDE per length; C ≤0.035% on MTC; S1/S5/S7/S8/S9 on order
Documents EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Common TP304L and dual TP304/TP304L sizes in Schedules 10S, 40S, and 80S are frequently available from stock, and stock certificates are checked for carbon, edition, and dual-grade validity before we offer them. Heavy-wall seamless and special sizes are usually mill-order items. Enquiries should state the SA-312 edition, TP304L (UNS S30403), SML/WLD/HCW, NPS or OD × wall (and whether wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements, so mill slots line up with your need date. Cut lengths, beveling, and packing-list marking are available on confirmed orders, and grouping project sizes onto one heat keeps the chemistry consistent while helping meet mill minimums without over-ordering.

FAQ

Is ASME SA312 the same as ASTM A312 for TP304L?
For chemistry (Table 1), tensile (Table 4), manufacturing types, heat treatment, and most testing language, ASME SA-312/SA-312M matches ASTM A312/A312M of the referenced edition. Dual SA312/A312 marking is common when it is ordered. Name both editions on the purchase order and make sure the mill test certificate repeats them, so inspectors can verify the heat against the books you cited.
Seamless vs welded TP304L — which is better?
Neither is universally better. Seamless is the usual choice for heavy walls, high-pressure lines, and piping classes written around seamless product, while WLD and HCW are fully legitimate SA-312 forms when they are tested and annealed to the standard and usually cost less in common sizes. Choose the route your design code and datasheet allow, and check that SML, WLD, or HCW appears on both the stencil and the MTC.
Hydrostatic test vs NDE — which do I get on TP304L pipe?
Every length is either hydrostatically tested or nondestructively electrically tested, and the manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification requires one of them, state it on the PO and confirm the chosen test on the MTC for each length. NPS 10 and larger may be marked NH only when you accept a system test instead.
Does SA-312 Table 4 set a hardness limit for TP304L?
No. Table 4 lists tensile strength, yield strength, and elongation for TP304L, but no hardness maximum, so catalogue Brinell or Rockwell figures are not specification requirements. If hardness matters for your fabrication or for an end-user rule, write the limit and the test method on the purchase order, and we will make sure the mill reports it on the certificate.
What is the UNS number and chemistry of TP304L?
Table 1 lists TP304L as UNS S30403 with C ≤0.035%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 18.0–20.0%, and Ni 8.0–13.0%, with no molybdenum or nitrogen requirement. Footnote D allows carbon up to 0.040% on small-OD or light-wall pipe. Put both TP304L and S30403 on every document you issue.
TP304L vs TP304 — which should I order?
Order TP304L, with C ≤0.035% and a 70/25 ksi floor, when as-welded sensitization resistance is written into the specification. Order TP304, with C ≤0.08% and 75/30 ksi, when the project accepts the higher carbon and wants the higher allowables. Dual TP304/TP304L gives both at once when one heat meets both Table 1 rows and the TP304 tensile floor.
TP304L vs TP316L — which is better in chlorides?
TP316L is the better choice for chloride, seawater, or brine service, because its 2–3% molybdenum improves pitting and crevice resistance. Both are low-carbon grades with good as-welded corrosion behaviour, and both have the same 70/25 ksi Table 4 floor. Choose TP304L for oxidizing and mild service and TP316L once chlorides become a real design concern.
Why is nickel 8.0–13.0% on TP304L but 8.0–11.0% on TP304?
Carbon is a strong austenite former, so when the carbon ceiling drops to 0.035% the mill may need a little more nickel to keep the structure fully austenitic and the ferrite balance in range. Table 1 therefore widens the nickel window to 13.0% on TP304L. A dual TP304/TP304L heat has to keep nickel within 8.0–11.0% to satisfy both rows.
What does Table 1 Footnote D mean for TP304L carbon?
Footnote D allows carbon up to 0.040% on small outside diameter or light-wall TP304L pipe where the mill needs it, instead of the normal 0.035% ceiling. If your project needs 0.035% across every size, or a tighter carbon limit for corrosion reasons, state that on the purchase order so the mill selects heats accordingly before production.
What filler metal should I use to weld TP304L pipe?
SA-312 Table 6 lists ER308L (UNS S30883 / W30843) for TP304L. Put ER308L on the WPS and PQR so the weld deposit keeps the same low-carbon protection as the pipe; standard ER308 gives away part of the reason for buying the L grade. Mill seams on WLD and HCW pipe are autogenous, so Table 6 applies to repairs and site joints.
What heat treatment applies to TP304L?
TP304L is not individually listed in Table 2, so it takes the default solution anneal at 1900 °F [1040 °C] minimum followed by water quench or another rapid cool. Seamless pipe may be quenched after hot forming when the edition allows and the finishing temperature is not below that minimum. The anneal statement should appear on the MTC for every lot.

Conclusion

ASME SA312 TP304L / UNS S30403 is the low-carbon 18-8 stainless pipe grade, with C ≤0.035% (Footnote D 0.040% on small or light-wall sizes), Cr 18.0–20.0%, and Ni 8.0–13.0% in Table 1, a 70/25 ksi Table 4 floor with 35% L / 25% T elongation, the default 1900 °F [1040 °C] solution anneal, and ER308L filler from Table 6. It is the safe choice for welded corrosive service, while ASME SA312 TP304 Stainless Steel Pipe or dual TP304/TP304L gives higher allowables and ASME SA312 TP316L Stainless Steel Pipe handles chlorides. Order the manufacturing type, size and wall, finish, carbon reporting, any dual marking, and supplementary tests explicitly. For stock checks, mill certificates, or dual SA-312/A312 supply questions, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category on steelspecs.com.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X