ASME SA312 TP309Cb Stainless Steel Pipe | ASME SA312 Stainless Steel - SHH STEEL

ASME SA312 TP309Cb Stainless Steel Pipe | SA 312/SA 312M

ASME SA312 TP309Cb (UNS S30940) stainless steel pipe under SA-312/SA-312M (ASTM A312/A312M): seamless (SML), welded (WLD) and heavily cold-worked (HCW); C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–16.0%, Mo ≤0.75%, Nb 10×C min to 1.10% max; Table 4 minima 75/30 ksi; solution annealed. SHH STEEL supplies with EN 10204 3.1 MTCs.
Grade
TP309Cb / UNS S30940
Standard
ASME SA312 / SA 312M (ASTM A312 / A312M)
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASME SA312 TP309Cb Stainless Steel Pipe

ASME SA-312/SA-312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. Grade TP309Cb is listed in Table 1 as UNS S30940. The “Cb” suffix means columbium—an older name for niobium (Nb); Footnote M states that niobium and columbium are alternative names for the same element. Commercially the same product may be called SA312 TP309Cb pipe, ASTM A312 TP309Cb pipe, A312 Grade TP309Cb, 309Cb, or 309Nb stainless steel pipe when the purchase order clearly references SA-312 or A312. For pressure piping and code work, cite the full grade designation, the UNS number, and the edition of the standard on the purchase order and on the mill test certificate—do not rely on a bare “309Cb” or “309Nb” market label.

TP309Cb is the niobium-stabilized member of the 309 family. Table 1 locks carbon at ≤0.08%, sets chromium at 22.0–24.0% and nickel at 12.0–16.0% (wider than the 12.0–15.0% window on ASME SA312 TP309S Stainless Steel Pipe and ASME SA312 TP309H Stainless Steel Pipe), lists molybdenum as a residual ceiling of ≤0.75%, and requires niobium not less than 10×C and not more than 1.10%. Niobium preferentially forms NbC so chromium stays available for corrosion resistance after welding—the same stabilization logic as 347/321-type grades applied to the 22Cr–12Ni base. Room-temperature Table 4 floors remain 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield. It is not an H grade: Table 5 does not mandate grain-size control, clause 6.2 reheat does not apply, and clause 17 heat-treatment lot marking is not required the way it is for H grades. Table 2 uses the default solution-annealing temperature of 1900 °F [1040 °C]. Table 6 lists AWS class “…” for TP309Cb—no classification is given—so filler selection is by agreement on the WPS.

SHH STEEL can supply ASME SA312 TP309Cb stainless steel pipe to the edition named on the enquiry, including seamless (SML), welded (WLD), and heavily cold-worked (HCW) routes; ASME B36.19 schedules and special OD/wall by agreement; EN 10204 3.1 mill test certificates that report the niobium value against the 10×C rule; and dual SA-312/A312 marking when the heat analysis, heat treatment, mechanical tests, and marking satisfy both editions named on the purchase order. Confirm NPS, wall or schedule, finish, length practice, and any product-analysis or supplementary tests on enquiry.

Common commercial names and how they map to the ordered product are listed below—use the full SA-312/A312 designation on the purchase order rather than market shorthand alone.

  • ASME SA312 TP309Cb / SA-312 Grade TP309Cb — preferred marking language for ASME-code and dual-marked pipe
  • ASTM A312 TP309Cb — same grade tables for chemistry and tensile when the ASTM edition is referenced
  • UNS S30940 — unified numbering system identity used on MTCs and in cross-reference tables
  • 309Cb / 309Nb stainless steel pipe — market shorthand; confirm Nb ≥10×C and ≤1.10%, C ≤0.08%, Ni 12.0–16.0%, and Mo ≤0.75% on the order

TP309Cb is not a drop-in for ASME SA312 TP309S Stainless Steel Pipe, ASME SA312 TP309H Stainless Steel Pipe, or ASME SA312 TP309HCb Stainless Steel Pipe on a shared “309” market label—each has its own Table 1 row. Versus TP309S, TP309Cb adds the mandatory niobium rule and the wider nickel window; a 309S heat with accidental residual niobium is not TP309Cb unless it meets the 10×C floor and is certified accordingly. Versus TP309H, TP309Cb is the non-H stabilized grade—no carbon floor of 0.04%, no Table 5 grain-size rule, and no clause 6.2 reheat. Versus TP309HCb (UNS S30941), the HCb grade adds the H-grade carbon range (0.04–0.10%), grain-size control, and reheat while keeping Nb stabilization. Dual marking within the 309 family is only considered when chemistry and (where applicable) H-grade rules overlap—stabilization alone does not convert a heat. Hub: ASME SA 312/SA 312M.

Manufacturing Types (SML / WLD / HCW)

ASME SA-312 defines three manufacturing routes that may be marked on finished TP309Cb pipe. Selecting the route is a purchase-order decision driven by design code, size range, wall thickness, and inspection preference. It does not change the Table 1 chemistry of Grade TP309Cb—melting must still meet C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–16.0%, Mo ≤0.75%, and Nb 10×C min to 1.10% max—and every route must still pass through the solution anneal required by SA-312.

  • Seamless (SML) — no welding at any stage of manufacture. Seamless is preferred for furnace tubes, heater coils, and pressure parts when the project specification excludes welded pipe, when thick walls favor seamless production, or when the piping class documentation is written around seamless product only. Hot-finished or cold-finished seamless must still be solution annealed and rapidly cooled to the Table 2 practice.
  • Welded (WLD) — automatic welding without filler metal. The weld is finished so that the pipe meets dimensional and mechanical requirements after the final heat treatment required by SA-312. Welded product is widely used for ducts, headers, and common NPS/schedule combinations where the code accepts welded austenitic pipe; the plate heat must itself meet S30940 chemistry including the niobium rule.
  • Heavily cold-worked (HCW) — welded pipe that is cold worked to a reduction of area of wall and weld of at least 35% before the final anneal, again without filler metal in the longitudinal weld. The weld is radiographed before cold work. HCW is ordered when the buyer wants the HCW marking and the process controls written into SA-312 for that route; clause 11.5 capability for S9 weld-decay testing still applies to HCW when S9 is ordered.

Each finished length is hydrostatically tested or nondestructively electrically tested; the manufacturer may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser agrees to a system test in lieu of hydrotest. Lot definitions follow clause 11.1. Clause 17 heat-treatment lot marking is not mandatory for non-H grades the way it is for ASME SA312 TP309H Stainless Steel Pipe and ASME SA312 TP309HCb Stainless Steel Pipe, though many buyers request lot identity on the stencil and MTC for receiving clarity. Niobium-bearing melts need controlled melting so Nb meets the 10×C floor without exceeding 1.10%; grouping project sizes onto one heat improves Nb consistency and often helps meet mill minimum order quantities that are higher than for commodity 304.

Lead times are typically similar to ASME SA312 TP309S Stainless Steel Pipe when quantities fit a mill heat, but remnant fills from prior Nb heats can still cut weeks off small urgent lots when sizes match. Plan procurement early for furnace-coil seamless sizes, and confirm route, edition, and any supplementary tests (S1, S5, S7, S9) before placing a mill order so the certificate matches the design basis. Where the service is oxidation-limited without a welded-HAZ corrosion case, switch the conversation to TP309S before the mill melts the heat; where creep governs and stabilization is still required, move the conversation to TP309HCb instead.

Chemical Composition of SA312 TP309Cb

Two chemistry layers matter: melting (heat / ladle) analysis—mandatory per heat under ASME SA-312/ASTM A312 Table 1—and product analysis when ordered (Suppl. S1 / PO). SA-312/A312 defer product-analysis tolerances through ASTM A999/A999M §6.3 to ASTM A480/A480M Table A1.1. SHH STEEL reports actual ladle and, when ordered, product values—never unpublished tighter windows. On heat analysis, every certificate must show a niobium value that satisfies Nb ≥10×C and Nb ≤1.10%; spot-check the arithmetic on receipt.

Melting analysis (heat / ladle analysis) — Table 1

Heat analysis for Grade TP309Cb / UNS S30940 from ASME SA-312/SA-312M (ASTM A312/A312M) Table 1 is summarized below. Values are maximum unless a range is shown; ellipses (…) mean no requirement in the ordered edition.

Element TP309Cb / UNS S30940 melting analysis
Carbon (C) ≤ 0.08
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 22.0 – 24.0
Nickel (Ni) 12.0 – 16.0
Molybdenum (Mo) ≤ 0.75
Niobium (Nb / Cb) 10 × C min, 1.10 max
Nitrogen (N) … (no requirement)

Source: SA-312 Table 1, Grade TP309Cb. Footnote M: Nb and Cb are the same element. Table cell: 10×C min, 1.10 max. (Footnote G wording of 1.00 max for some grades is noted in pack UNCERTAIN; this pack uses the table-cell 1.10 max.)

Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1

When product analysis is ordered, apply A480 Table A1.1 tolerances to the Table 1 limits. The heat-analysis 10×C niobium floor is not relaxed by product tolerance.

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.08 0.01 over ≤ 0.09
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 22.0 – 24.0 0.25 under / over 21.75 – 24.25
Nickel (Ni) 12.0 – 16.0 0.15 under / over 11.85 – 16.15
Molybdenum (Mo) ≤ 0.75 0.05 over ≤ 0.80
Niobium (Nb / Cb) 10×C min – 1.10 max 0.05 (A480 Cb+Ta to 1.50) Heat-analysis 10×C floor not relaxed by product tolerance

Niobium check: on heat analysis, Nb ≥10×C and ≤1.10%. Example: C = 0.06% requires Nb ≥0.60% and ≤1.10%. Product tolerance never relaxes the heat-analysis 10×C floor. Cr product tolerance uses the 20–30% row (0.25); Ni uses the 10–20% row (0.15). Titanium is not required for TP309Cb—stabilization is by niobium alone. Copper and nitrogen have no Table 1 requirement (ellipsis).

Element TP309S TP309Cb TP309HCb
C ≤ 0.08 ≤ 0.08 0.04 – 0.10
Ni 12.0 – 15.0 12.0 – 16.0 12.0 – 16.0
Mo ≤ 0.75 ≤ 0.75 ≤ 0.75
Nb … 10×C – 1.10 10×C – 1.10

The side-by-side table above shows why a shared “309” market label is dangerous: ASME SA312 TP309S Stainless Steel Pipe has no Nb requirement and Ni only to 15.0%, while TP309Cb and ASME SA312 TP309HCb Stainless Steel Pipe share the Nb rule and the 16.0% nickel ceiling but differ on carbon (and H-grade controls). Mills often target carbon well below 0.08% so that the 10×C niobium minimum stays moderate—for example 0.04% C needs only 0.40% Nb minimum—which reduces niobium cost and keeps the alloy easier to hot work. Buyers who need higher carbon for creep-range strength should say so early; those needs usually push the conversation toward TP309HCb instead of raising carbon on a non-H heat.

Mechanical Properties of SA312 TP309Cb

Room-temperature tensile requirements for Grade TP309Cb come from ASME SA-312/ASTM A312 Table 4. Stabilization improves welded corrosion behaviour; it does not raise the room-temperature tensile floor above the sister 309 grades. Actual mill values are often higher than the minima, but design still uses Table 4 unless the purchase order states higher guarantees.

Property TP309Cb / UNS S30940
Tensile strength, min 75 ksi [515 MPa]
Yield strength, min 30 ksi [205 MPa]
Elongation, min 35% longitudinal / 25% transverse
Hardness No Table 4 maximum
Grain size Not listed in Table 5 (not an H grade)

Source: SA-312 Table 4 for TP309Cb. Same 75/30 ksi floors as ASME SA312 TP309S Stainless Steel Pipe and ASME SA312 TP309H Stainless Steel Pipe. Elongation follows the Table 4 row for the ordered edition.

Base mechanical testing includes tension on a lot basis and flattening (or the alternate bend where the standard permits) typically on 5% of the lot, plus hydrotest or NDE on every length. Elevated-temperature tensile and rupture tests are purchase-order options, not base SA-312 requirements. For pressure-retaining parts, use Section II Part D allowables for S30940 where listed; stabilization does not by itself raise allowable stresses above TP309S at the same temperature. Annealed TP309Cb retains austenitic toughness to low temperature; impact testing is a construction-code or PO matter, not an SA-312 base test.

Although Table 4 has no hardness maximum, fabricators sometimes set a Rockwell limit for bending or expanding—put any such limit on the PO and verify it on the MTC if required. Like other 309 grades, TP309Cb hardens quickly when cold worked; intermediate anneals may be needed for severe forming, and those anneals should still meet the Table 2 minimum temperature unless a project spec says otherwise. For creep-range stabilized design with grain-size control, see ASME SA312 TP309HCb Stainless Steel Pipe rather than stretching a non-H heat.

Dimensions and Tolerances

Dimensional supply for SA312 TP309Cb pipe follows ASME B36.19 schedules for common NPS/schedule combinations, with special OD and wall by agreement when the heater or duct geometry needs a non-standard section. Outside-diameter variations follow ASTM A999/A999M; wall-thickness variations follow SA-312 Table 3 as summarized below. State whether wall is nominal or minimum (Suppl. S8) on the purchase order so the mill does not ship the wrong interpretation.

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%

Source: SA-312 Table 3; outside diameter variations per A999/A999M.

  • Lengths — NPS 1/8–8 commonly furnished up to 24 ft unless otherwise agreed; SRL, DRL, or cut-to-length on order
  • Cut lengths — typically ≤1/4 in. [6 mm] over unless the PO states a tighter band
  • Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen

Furnace and process lines often order by OD × wall rather than by NPS/schedule. Large welded headers from 309Cb plate are common—clarify SA-312 pipe versus SA-240 plate certification on the enquiry so companion components and the pipe share one identity. Thermal expansion is high on long hot runs; supports must allow growth. Straightness and ovality for radiant tubes may need tighter limits than SA-312 base rules—state them on the PO so pipe is produced, not sorted, to the requirement. For socket-weld or threaded ends on thin schedules, confirm the wall remains adequate after the 12.5% under-tolerance. Jointers are not permitted unless the purchase order expressly allows them; cut-to-length programmes for heater tubes should include an allowance for fit-up scrap so the mill does not ship under-length pieces.

Equivalent Grades

Equivalence for TP309Cb is primarily an ASME/ASTM identity question. The governing pipe designation is ASME SA-312 Grade TP309Cb / UNS S30940; market names and plate counterparts must be mapped back to that row before a mill is asked to dual-mark or substitute.

Designation Notes
ASME SA-312 TP309Cb / UNS S30940 Governing pipe grade
ASTM A312 TP309Cb / UNS S30940 Same Table 1 / Table 4 when the ASTM edition is referenced
309Cb / 309Nb Trade names; confirm S30940 chemistry including Nb 10×C – 1.10
SA-240 / A240 309Cb Plate/sheet counterpart—not a pipe specification by itself
EN / JIS No one-to-one equivalent asserted in this pack

Related SA-312 grades on steelspecs.com: ASME SA312 TP309S Stainless Steel Pipe, ASME SA312 TP309H Stainless Steel Pipe, ASME SA312 TP309HCb Stainless Steel Pipe, ASME SA312 TP310Cb Stainless Steel Pipe, ASME SA312 TP347 Stainless Steel Pipe, ASME SA312 TP310S Stainless Steel Pipe. Nb and Cb mean the same element—do not treat “309Nb” and “309Cb” as different alloys on the purchase order. Versus ASME SA312 TP347 Stainless Steel Pipe (stabilized 18-8), TP309Cb stabilizes a 22Cr–12Ni base for higher-temperature oxidation plus welded integrity; they are not substitutes for each other, and dual marking with TP347 is not applicable because the chromium and nickel ranges differ. Dual marking is only considered within the 309 family when chemistry (and H-grade rules, where applicable) actually overlap. Versus ASME SA312 TP304 Stainless Steel Pipe, the extra chromium and nickel raise oxidation resistance by roughly one temperature class, but 304 remains the wrong choice when the design temperature needs 309-level hot-gas resistance.

Heat Treatment and Delivery Condition

TP309Cb is not individually listed in Table 2 with a special temperature; the default solution-annealing practice of 1900 °F [1040 °C] minimum with rapid cooling applies. Clause 6.2 allows direct quench after hot forming for non-H grades—the mandatory reheat-before-quench rule is written for H grades such as ASME SA312 TP309H Stainless Steel Pipe and ASME SA312 TP309HCb Stainless Steel Pipe. Delivery remains the solution-annealed condition required by SA-312 unless the ordered edition and purchase order state otherwise.

  • Solution annealed and rapidly cooled — Table 2 default 1900 °F [1040 °C] minimum
  • Free of scale and exogenous iron — descaled / pickled or equivalent as ordered
  • Passivation — available on request when the end-user specification requires it
  • No Table 5 grain-size requirement — unlike TP309H / TP309HCb

Owner-specified stabilization heat treatments after fabrication welding—holding in the NbC precipitation range, often around 1650–1750 °F—are purchaser requirements, not SA-312 base rules. Write temperature and time on the PO if needed, and engineer the treatment so it does not conflict with dimensional tolerances or code heat-treatment rules. Bright annealing of small TP309Cb tube must still reach the Table 2 minimum; ask for the bright-anneal temperature on the MTC when that finish is ordered. Cite the ordered edition’s Table 2 practice on the enquiry so the mill does not apply a neighboring H-grade reheat habit to a non-H heat.

Corrosion Resistance

TP309Cb combines 309-level oxidation resistance with improved intergranular resistance after welding. Chromium at 22.0–24.0% supports hot-air and flue-gas oxidation performance similar to ASME SA312 TP309S Stainless Steel Pipe; niobium stabilization reduces chromium-carbide sensitization in weld heat-affected zones so the passive film stays intact when the fabrication cycles through sensitizing temperatures or sees corrosive condensate on shutdown.

  • Oxidation — 22–24% Cr; similar hot-air and flue-gas behaviour to TP309S
  • Intergranular attack — Nb ≥10×C preferentially forms NbC, leaving chromium available in the HAZ
  • Polythionic acid / shutdown SCC risk — stabilized grades are often preferred in refinery units where shutdown chemistry creates SCC risk; confirm with project corrosion engineering
  • Chlorides — Mo ≤0.75% is a residual ceiling, not intentional alloying; TP309Cb is not a 316 substitute for aqueous chloride service
  • Sigma-phase risk — high-Cr grades can still form sigma after long intermediate-temperature exposure; design dwell times accordingly

Verify intergranular resistance with Suppl. S7 (ASTM A262 Practice E) when the service case is critical, and use Suppl. S9 weld-decay testing when welded pipe must demonstrate comparable weld and base-metal loss rates. Neither test is automatic—order them when the corrosion case needs proof. Compared with ASME SA312 TP347 Stainless Steel Pipe (stabilized 18-8), TP309Cb offers higher oxidation resistance while keeping the stabilization concept. If the line sees both high-temperature flue gas and acidic condensate on shutdown, stabilization helps the cold cycle while chromium helps the hot cycle; neither replaces good drainage and neutralization procedures written into the operating manual.

Applications of SA312 TP309Cb Pipe

Buyers typically select TP309Cb when the project already wants 309-level oxidation resistance and the design review adds a welded-HAZ corrosion or polythionic-acid risk that an unstabilized heat cannot answer. The grade earns its keep by protecting weld integrity through thermal cycles rather than by raising the continuous oxidation limit above TP309S.

Application Why TP309Cb Note
Welded furnace and process piping Stabilization for HAZ integrity Order S7 if needed
Refinery units with shutdown SCC risk Nb ties up carbon Compare TP309HCb if creep governs
Heat-treatment equipment 309 oxidation resistance Carburization may need other alloys
Dissimilar transition pieces 309 dilution plus stability Document WPS
Chemical plant hot-gas lines Welded fabrication without PWHT Confirm condensate risk

For creep-range stabilized service with grain-size control, see ASME SA312 TP309HCb Stainless Steel Pipe. For unstabilized oxidation service without a HAZ case, see ASME SA312 TP309S Stainless Steel Pipe. Track HAZ-related failures in sister units when deciding between TP309S and TP309Cb—lifecycle cost often favors the stabilized grade when weld repairs and unplanned shutdowns dominate the maintenance record. Typical size mix runs from instrument connections NPS 1/2–2 through process lines NPS 3–8 to large welded ducts NPS 12–24; availability of fittings and flanges in 309Cb chemistry can limit the line list, so confirm companion components before freezing the isometric. When replacing TP309S with TP309Cb in an existing unit, review weld procedures and filler selections—the base-metal change alone does not update the WPS.

Weldability

TP309Cb welds with GTAW, GMAW, SMAW, and SAW using practices familiar to fabricators of other 309 grades. Stabilization improves as-welded intergranular resistance in the heat-affected zone, which is the main reason the grade is chosen for welded fabrications that see corrosive media or that cycle through sensitizing temperatures. Mill WLD and HCW longitudinal welds are autogenous (no filler); Table 6 guidance applies to joining with filler, not to the mill seam.

Filler and Table 6: TP309Cb is listed with AWS class “…”—no classification is given. Filler selection is by agreement and must be recorded on the WPS. Matching Nb-bearing 309 or 347-type fillers are sometimes used so the weld metal itself stays stabilized; do not assume plain ER309 without niobium preserves full stabilization in the deposited metal. Freeze the AWS (or EN) class on the WPS/PQR before production welds.

  • Moderate heat input; clean joints free of oil, paint, and exogenous iron
  • Argon shielding and backing gas for GTAW root passes
  • Remove heat tint; pickle when aqueous or condensate service follows
  • Mill seams autogenous; clause 15 repairs must identify any filler used

Qualify welding procedures to ASME Section IX on S30940 material. A PQR on ASME SA312 TP309S Stainless Steel Pipe does not automatically cover the Nb-bearing grade. Dissimilar welds of TP309Cb to carbon steel still commonly use 309-type fillers for dilution control; if the weld must also resist intergranular attack in condensate, decide whether the filler itself needs Nb or whether a barrier butter layer is required, and capture that decision in the WPS. After high-temperature service exposure, clean thoroughly before repair welding and consider whether a local stabilizing treatment is needed after repair—follow producer guidance for Nb-stabilized 309.

Surface Finishes

Surface condition for SA312 TP309Cb pipe is stated on the purchase order. Typical mill finishes available from SHH STEEL supply include the following options:

  • Annealed and pickled (AP) — solution annealed, descaled in acid pickle or an equivalent process, producing a matte gray finish common for process and furnace pipe
  • Blasted and pickled — often used for heavy-wall seamless where scale removal benefits from blast first
  • Bright annealed (BA) — annealed in a protective atmosphere to a brighter surface where the order allows and mill capability exists for the size; temperature must still meet the Table 2 minimum
  • As-annealed light oxide — sometimes accepted for furnace parts by agreement when the protective scale will form in service anyway
  • Mechanically polished — grit or Ra-controlled polish on OD and/or ID when ordered; polishing does not replace solution annealing
  • Bead-finished welded OD — weld bead rolled or ground flush as agreed for WLD/HCW product

Passivation after pickle or polish can be added when the end-user specification requires it. Electropolishing is uncommon for furnace service but available for special clean-service needs by agreement. Use low-halide marking inks on high-temperature lines when the project specification bans chloride-bearing inks. State finish, passivation, and any ink restriction on the order so the mill does not ship a default AP finish into a BA or polished requirement.

Inspection and Testing

Base inspection and testing for SA-312 TP309Cb pipe combines chemistry (including niobium arithmetic), mechanical, and integrity checks. The following items form the usual acceptance package; supplementary requirements apply only when written on the purchase order.

  • Heat (melting) analysis — mandatory per heat against Table 1 for TP309Cb (UNS S30940), including C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–16.0%, Mo ≤0.75%, and Nb ≥10×C / ≤1.10%
  • Product analysis — when ordered (Suppl. S1 / purchase-order language), using A480 Table A1.1 tolerances via A999 §6.3; useful to confirm Nb and residual Mo on finished pipe
  • Tension test — Table 4 tensile, yield, and elongation on a lot basis (75/30 ksi minima)
  • Flattening test — or alternate bend where the standard permits (typically on 5% of the lot)
  • Hydrostatic test or nondestructive electric test — each length; manufacturer’s option unless the order fixes the method
  • Visual and dimensional check — against ordered NPS/schedule or OD/wall and the applicable tolerance clauses

Mill test certificates: EN 10204 3.1 is the standard documentation package from SHH STEEL supply. The certificate must report the niobium value so receiving inspection can verify Nb ≥10×C and Nb ≤1.10%. EN 10204 3.2 or third-party witness (SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency) is arranged when specified and should be booked before final testing. Dual ASME SA-312 / ASTM A312 certification is available when chemistry, heat treatment, mechanical tests, and marking satisfy the edition(s) named on the order.

Option Purpose
S1 product analysis Confirms Nb and other elements on finished pipe
S5 radiography Weld integrity on WLD pipe
S7 intergranular corrosion A262 Practice E after sensitizing treatment
S9 weld decay Compares weld and base-metal loss rates
OES / lab Nb Niobium verification; handheld XRF is limited for Nb

Receiving review should confirm Nb ≥10×C, Nb ≤1.10, C ≤0.08, Cr 22–24, Ni 12–16, Mo ≤0.75, tensile ≥75 ksi, yield ≥30 ksi, elongation, and hydro or NDE method. Third-party inspectors should verify Nb arithmetic against carbon on the MTC and confirm that the grade stencil reads TP309Cb or S30940—not merely “309.” PMI by OES on a sample length is a useful receiving check when multiple 309 variants share a laydown area. Mechanical tests follow clause 11.1 lot rules; for specialty Nb heats made in short campaigns, a lot may be only a few dozen lengths, so base test frequency is effectively high.

Packaging and Shipping

Export and domestic shipments of SA312 TP309Cb pipe are packed for handling and ocean or land transport. Typical packing practices from SHH STEEL supply include:

  • Seaworthy bundles — pipes strapped or cradled in bundles sized for container or break-bulk handling, with non-metallic separators where needed to protect finish; cradles or individual supports for heavy headers
  • End caps / protectors — plastic or metal caps on plain or beveled ends to reduce damage and contamination during transit
  • Marking — durable marking of specification, grade (TP309Cb), UNS S30940 when required, heat number, size (NPS or OD × wall / schedule), manufacturing type (SML / WLD / HCW), test letters, and mill identity as required by SA-312 and the purchase order
  • Export packing — waterproof wrapping or desiccant as agreed for polished or sensitive finishes; container stuffing photos on request; low-chloride inks on request

Segregate TP309Cb from TP309S, TP309H, and TP309HCb on the packing list and in the yard so stencil mix-ups do not travel with the shipment—mix-ups discovered after fabrication are expensive because the chemistries cannot be converted by heat treatment alone. When TP309Cb ships with TP309S on the same vessel, use separate bundles and distinctly colored tags. Receiving inspectors should compare stencil heat numbers against the MTC for every length and verify that Nb is reported before release to fabrication. Long thin-wall heater tubes are vulnerable to bending in transit; ship them in rigid frames or with close-spaced saddles, and keep interiors dry and capped so chloride-bearing moisture does not stain or pit the surface before installation. Shipment docs typically include packing list, invoice, B/L or AWB, and MTC (3.1 or 3.2) with Nb reported, plus origin/customs papers per Incoterms.

Why Choose SHH STEEL

SHH STEEL supplies specification-driven stainless plate and pipe. For ASME SA312 TP309Cb / UNS S30940 we quote against the edition you name, report the full Table 1 window on the MTC—including C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–16.0%, Mo ≤0.75%, and Nb ≥10×C / ≤1.10%—and keep heat identity unbroken from melt through finished length. Receiving inspection then clears the heat against Table 1 and Table 4, with the niobium arithmetic checked on every certificate, rather than against a vague “309Cb” catalog sheet. We flag missing Nb fields or failed 10×C arithmetic on supplier MTCs before shipment, so non-conforming paperwork is caught at the mill—not at the fabricator. We also stay honest about Table 6: no AWS filler class is listed for TP309Cb, so filler selection stays by agreement on the WPS.

  • Specification fidelity — chemistry and tensile to SA-312/A312 Table 1 and Table 4 for TP309Cb (S30940); Nb reported and checked against 10×C; no unstabilized 309S sold as 309Cb
  • Mill resources — SML, WLD, and HCW from qualified stainless pipe mills with heat traceability; cutting and beveling on confirmed orders
  • Documentation — EN 10204 3.1 MTCs standard with Nb reported; 3.2 or third-party inspection on request
  • Dual marking — ASME SA-312 and ASTM A312 when the heat and tests meet both requirements you name
  • Related grades — sister 309-family and 310Cb / 347 SA-312 grades when projects buy matched high-temperature or stabilized packages
  • Export packing — seaworthy bundles, end protectors, and durable grade/heat/size/type marking

Quotations follow your purchase-order language for edition year, manufacturing type, size, finish, and any supplementary tests you name (S1, S5, S7, S9). Ask for coordinated plate-and-pipe heats when a project needs matching Nb levels across SA-240 and SA-312 forms. Grade hub: ASME SA 312/SA 312M.

Supply Capability

SHH STEEL can supply ASME SA312 TP309Cb / UNS S30940 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.

Item SHH STEEL capability for TP309Cb
Standard ASME SA-312/SA-312M and/or ASTM A312/A312M Grade TP309Cb (UNS S30940)
Manufacturing types SML, WLD, HCW
Size NPS 1/8 and up per ASME B36.19; special OD/wall by agreement
Schedules 5S, 10S, 40S, 80S and non-standard walls
Length SRL, DRL, or cut-to-length
Finish Annealed and pickled; blasted and pickled; bright annealed or polished by agreement
Testing Tension, flattening/bend, hydro or NDE per length; Nb arithmetic on MTC; S1/S5/S7/S9 on order
Documents EN 10204 3.1 with Nb reported; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

TP309Cb is less common in distributor stock than TP309S, so mill-run orders are typical and lead times track plate and melt schedules for Nb-bearing 309. Common sizes may occasionally be available from remnant lengths of prior Nb heats; heavy walls and special OD/wall combinations are mill-order items. Enquiries should state the SA-312 edition, TP309Cb / S30940, SML/WLD/HCW, NPS or OD×wall (nominal or minimum), length practice, finish, Nb reporting expectation, and any product-analysis or 3.2 requirements so mill slots align with your need date. Cut lengths, beveling, and packing-list marking are available on confirmed orders. Combining project sizes into one heat improves Nb consistency and helps meet mill minima without over-ordering. For urgent small quantities, ask about remnant lengths from recent Nb heats before authorizing a new melt—remnants can cut weeks from the schedule when sizes match.

FAQ

Is ASME SA312 the same as ASTM A312?
For chemistry (Table 1), tensile (Table 4), manufacturing types, and most testing language, ASME SA-312/SA-312M matches ASTM A312/A312M of the referenced edition. Dual SA312/A312 marking is common when ordered. Name both editions on the purchase order and mill test certificate so inspectors can verify the heat against the exact books you cited—do not assume a bare market grade stamp covers dual certification.
What is the UNS number for TP309Cb?
Table 1 lists TP309Cb as UNS S30940. Use that UNS on the purchase order, stencil, and MTC so chemistry and tensile rows stay unambiguous, and so Nb arithmetic is checked against the correct grade row. When the project mixes plate and pipe, carry the same UNS language across forms, but still order pipe to SA-312/A312—not to the plate specification alone.
TP309Cb vs TP309S — which should I order?
TP309Cb requires Nb (10×C min, 1.10% max) and allows Ni to 16.0%; TP309S has no Nb requirement and Ni only to 15.0%. Both use C ≤0.08% and 75/30 ksi floors, and neither is an H grade. Put the design-code grade and UNS on the datasheet and purchase order before you compare price—switching to TP309S after fabrication drawings are frozen usually means a material change notice, not a free mill substitution.
TP309Cb vs TP309H — which should I order?
TP309H is the creep-service H grade with C 0.04–0.10%, Table 5 grain size, and clause 6.2 reheat, but without a niobium requirement. TP309Cb is the non-H stabilized grade with Nb 10×C–1.10 and Ni to 16.0%. They solve different problems—do not treat them as interchangeable on a shared “309” label. Put the design-code grade and UNS on the purchase order before you compare price.
TP309Cb vs TP309HCb — which should I order?
Both require niobium stabilization (10×C min, 1.10% max) and allow Ni to 16.0%; TP309HCb adds C 0.04–0.10%, Table 5 grain control, and clause 6.2 reheat, while TP309Cb is non-H with C ≤0.08%. Order the datasheet grade. Put the design-code grade and UNS on the purchase order before you compare price—switching after drawings are frozen usually means a material change notice, not a free mill substitution.
Seamless vs welded TP309Cb — which is better?
Neither is universally better. Choose the manufacturing type your design code and datasheet allow; both are legitimate SA-312 forms when tested to the standard, and both must still meet S30940 chemistry including the niobium rule. State SML, WLD, or HCW on the purchase order and confirm the same letters on the pipe marking and MTC—mixing offers that differ only in manufacturing type is a common bid-evaluation trap.
Can you dual-certify SA312 / A312 TP309Cb?
Yes, when heat analysis (including Nb ≥10×C and ≤1.10%), heat treatment, mechanical tests, and marking meet both editions named on the order. Write the ASME and ASTM edition years on the PO, and require the MTC to reference both books so receiving inspection can clear the heat without a second paperwork chase after shipment.
Hydrostatic test vs NDE — which do I get?
Each length is hydrotested or nondestructively electrically tested. Manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification locks one method, state it on the PO and verify the chosen test appears on the MTC for every length—silent mill option is not the same as an approved project method.
What heat treatment / anneal temperature applies to TP309Cb?
Table 2 default 1900 °F [1040 °C] minimum with rapid cooling. Not an H grade—clause 6.2 reheat and Table 5 grain-size control do not apply. Delivery remains the solution-annealed condition required by SA-312 unless the edition and PO state otherwise. Cite the ordered edition’s Table 2 practice on the enquiry so the mill does not apply a neighboring H-grade reheat habit by mistake.
What Table 1 chemistry defines TP309Cb?
Table 1: C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–16.0%, Mo ≤0.75%, Nb 10×C min / 1.10% max (UNS S30940). Values are melting-analysis limits from the ordered edition—do not invent tighter catalog windows. When product analysis is needed, order it explicitly (Suppl. S1 / PO language) rather than assuming ladle values alone will satisfy receiving inspection.
What are the Table 4 tensile requirements for TP309Cb?
Table 4 minima are 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield (elongation per the standard’s Table 4 row). Actual MTC values are often higher; design still uses Table 4 unless the PO states higher guarantees. Record the Table 4 row and UNS S30940 on the datasheet so fabricators do not substitute a sister-grade strength line from memory.
What filler metal should I use to weld TP309Cb pipe?
Table 6 shows “…” for TP309Cb—filler by agreement. Matching Nb-bearing 309 or 347-type fillers are sometimes used so weld metal stays stabilized; plain ER309 without Nb may not preserve full stabilization in the deposit. Freeze the AWS (or EN) class on the WPS/PQR before production welds, and remember mill WLD/HCW longitudinal welds are autogenous—Table 6 guidance applies to joining with filler, not to the mill seam.

Conclusion

ASME SA312 TP309Cb (UNS S30940) is the niobium-stabilized 22Cr–12Ni pipe grade in SA-312: C ≤0.08%, Nb 10×C min to 1.10% max, Ni 12.0–16.0%, Mo ≤0.75%, with 75/30 ksi room-temperature minima and a default 1900 °F [1040 °C] anneal. It is not a drop-in for TP309S (no Nb), TP309H (H-grade carbon and grain-size rules without Nb), or TP309HCb (H-grade plus Nb)—each has its own Table 1 row. Table 6 lists no AWS filler class (filler by agreement). Order the manufacturing type (SML/WLD/HCW), schedule or wall, finish, Nb reporting, and any product analysis or supplementary tests explicitly. For stock checks, mill certificates, or dual SA-312/A312 supply questions, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category on steelspecs.com.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X