ASME SA312 TP316LN Stainless Steel Pipe | SA 312/SA 312M
What is ASME SA312 TP316LN Stainless Steel Pipe
ASME SA-312/SA-312M covers seamless, welded and heavily cold-worked austenitic stainless steel pipe for high-temperature and general corrosive service, and it is technically aligned with ASTM A312/A312M of the referenced edition. Grade TP316LN is listed in Table 1 as UNS S31653. For pressure piping and code work, cite the grade, the UNS number and the edition of the standard on the purchase order and on the mill test certificate, rather than relying on a market label that several neighbouring grades share.
TP316LN combines L-grade low carbon (C ≤0.035%) with intentional nitrogen (N 0.10–0.16%) inside the Mo-bearing 316 envelope of Cr 16.0–18.0%, Ni 10.0–14.0% and Mo 2.00–3.00%. The nitrogen helps austenite stability and gives back some of the strength lost by cutting carbon, but SA-312 still releases the grade against the 75 ksi [515 MPa] tensile / 30 ksi [205 MPa] yield row of Table 4—the same floors as TP316, not the 80/35 ksi of TP316N. It is not an H grade, so there is no Table 5 grain-size rule or clause 6.2 reheat. Table 2 does not list S31653 individually, so the default 1900 °F [1040 °C] anneal with rapid cooling applies, and Table 6 maps the grade to the ER316L filler family. Where the ordered edition carries the small-diameter / light-wall carbon footnote that applies to the L grades, check it on the order rather than assuming it away.
SHH STEEL can supply ASME SA312 TP316LN stainless steel pipe to the edition named on the enquiry, in seamless (SML), welded (WLD) and heavily cold-worked (HCW) forms. We cover ASME B36.19 schedules and special OD and wall combinations by agreement, issue EN 10204 3.1 mill test certificates as standard, and can dual-mark SA-312/A312 when the heat analysis, heat treatment, mechanical tests and marking satisfy both editions named on the purchase order. Tell us the NPS, wall or schedule, finish, length practice and any product-analysis or supplementary tests at enquiry stage, and we will confirm stock or mill rolling against those details.
Common commercial names and how they map to the ordered product are listed below. Use the full SA-312/A312 designation on the purchase order rather than market shorthand alone, because the shorthand is where grade substitutions usually start.
- ASME SA312 TP316LN / SA-312 Grade TP316LN — preferred marking language for ASME-code and dual-marked pipe
- ASTM A312 TP316LN — same chemistry and tensile tables when the ASTM edition is referenced
- UNS S31653 — unified numbering identity used on MTCs, stencils and ASME Section II Part D cross-references
- 316LN / 316LN stainless steel pipe — market shorthand; confirm C ≤0.035%, N 0.10–0.16% and the 75/30 ksi row on the order
TP316LN is not a drop-in for ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 TP316N Stainless Steel Pipe, ASME SA312 TP316 Stainless Steel Pipe or ASME SA312 TP304LN Stainless Steel Pipe. Against TP316L, the difference is the required nitrogen band, which plain 316L heats rarely meet without being melted for it. Against TP316N, the nitrogen band is identical but carbon is capped at 0.035% instead of 0.08%, and the tensile row is 75/30 rather than 80/35 ksi—so the two cannot share an inspection and test plan. TP304LN uses the same low-carbon-plus-nitrogen logic without molybdenum. Hub: ASME SA 312/SA 312M.
Manufacturing Types (SML / WLD / HCW)
SA-312 defines three manufacturing routes that may be marked on finished TP316LN pipe. The route is a purchase-order decision driven by design code, size range, wall thickness and inspection preference. It does not change the Table 1 chemistry of UNS S31653, and every route must still finish with the solution anneal required by SA-312.
- Seamless (SML) — no welding at any stage. Preferred for small-bore and thick-wall pressure pipe, and wherever the piping class excludes welded product.
- Welded (WLD) — automatic welding without filler metal, finished so the pipe meets dimensional and mechanical requirements after final heat treatment. Common for larger NPS lines where the code accepts welded austenitic pipe.
- Heavily cold-worked (HCW) — welded pipe cold worked at least 35% in wall and weld before the final anneal, with the weld radiographed before cold work. Ordered when tighter OD and wall consistency matters.
Each finished length is hydrostatically tested or nondestructively electrically tested, and the manufacturer may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser agrees to a system test instead. State SML, WLD or HCW explicitly on the enquiry; bids that differ only in manufacturing type are a common evaluation trap, and the same letters should appear on the stencil and the MTC.
Chemical Composition of SA312 TP316LN
Melting analysis (heat / ladle analysis) — Table 1
The table below is the SA-312 Table 1 heat analysis for TP316LN / UNS S31653. Values are maximum unless a range is shown, and an ellipsis (…) means no requirement. These are the numbers the mill must report on the certificate, and they are the numbers receiving inspection should check first.
| Element | TP316LN / UNS S31653 melting analysis |
|---|---|
| Carbon (C) | ≤ 0.035 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 16.0 – 18.0 |
| Nickel (Ni) | 10.0 – 14.0 |
| Molybdenum (Mo) | 2.00 – 3.00 |
| Nitrogen (N) | 0.10 – 0.16 |
Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1
When product analysis is ordered (Supplementary Requirement S1 or PO wording), the check analysis may vary from the Table 1 limits by the A480 tolerances below. Product analysis is not automatic, so order it explicitly if your project needs it rather than assuming ladle values will satisfy the client inspector.
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.035 | 0.01 over | ≤ 0.045 |
| Manganese (Mn) | ≤ 2.00 | 0.04 over | ≤ 2.04 |
| Phosphorus (P) | ≤ 0.045 | 0.010 over | ≤ 0.055 |
| Sulfur (S) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Silicon (Si) | ≤ 1.00 | 0.05 over | ≤ 1.05 |
| Chromium (Cr) | 16.0 – 18.0 | 0.20 under / over | 15.80 – 18.20 |
| Nickel (Ni) | 10.0 – 14.0 | 0.15 under / over | 9.85 – 14.15 |
| Molybdenum (Mo) | 2.00 – 3.00 | 0.10 under / over | 1.90 – 3.10 |
| Nitrogen (N) | 0.10 – 0.16 | 0.01 under / over | 0.09 – 0.17 |
For certificate review, the two numbers that make a heat TP316LN are carbon at or below 0.035% and nitrogen inside 0.10–0.16%; the Cr, Ni and Mo bands are the same as TP316. Against TP316N, the nitrogen requirement is identical and the carbon limit is the only chemistry difference, but it moves the grade to a different Table 4 row. Product-analysis limits apply the A480 tolerances shown above, including ±0.01 on nitrogen and ±0.10 on molybdenum. A certificate marked “316LN” that does not report nitrogen, or that quotes UNS S31603 instead of S31653, should go back to the mill before the pipe is accepted.
Mechanical Properties of SA312 TP316LN
| Property | TP316LN |
|---|---|
| Tensile, min | 75 ksi [515 MPa] |
| Yield, min | 30 ksi [205 MPa] |
| Elongation | 35% L / 25% T |
TP316LN is released against 75/30 ksi, and that is mandatory. Two errors show up in practice: releasing a TP316LN order against TP316N’s 80/35 ksi ITP, which wrongly rejects good pipe, and accepting a TP316N heat as TP316LN without checking carbon. Keep the Table 4 row and the UNS number S31653 together on the datasheet, and take design allowables from the code tables for that UNS rather than from a neighbouring 316 grade.
Actual certificate values are usually comfortably above the minima, but design and acceptance still use the Table 4 row unless the purchase order states higher guaranteed values. Record the row on the datasheet so fabricators and inspectors do not substitute a sister grade’s strength line from memory, and make sure the tension test on the MTC is traceable to the heat and lot that was shipped.
Dimensions and Tolerances
TP316LN pipe is normally ordered to ASME B36.19 schedules, with heavier B36.10 walls and special OD and wall combinations available by agreement. Wall thickness tolerance follows SA-312 Table 3, and outside diameter variations follow A999/A999M for the ordered size.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
Source: SA-312 Table 3; outside diameter variations per A999/A999M. Cut lengths should not be shorter than ordered, and random or fixed length practice should be stated on the enquiry. Special walls and non-standard sizes need written mill agreement before rolling slots are booked, so raise them early if your design does not fit a standard schedule.
Equivalent Grades
| Designation | Notes |
|---|---|
| ASME SA-312 TP316LN / UNS S31653 | Governing specification for ASME code work |
| ASTM A312 TP316LN / UNS S31653 | Same chemistry and tensile rows for the referenced edition |
| UNS S31653 | Unified numbering identity on MTC and stencil |
Cross-references to EN or other national numbers are not given here, because SA-312 does not define them and near-equivalents rarely match every Table 1 limit. If a project needs a cross-standard equivalence, treat it as an engineering decision against both specifications rather than a catalogue lookup. Dual SA-312/A312 certification is straightforward when both editions are named on the order. Related grades for comparison: ASME SA312 TP316 Stainless Steel Pipe, ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 TP316N Stainless Steel Pipe, ASME SA312 TP304LN Stainless Steel Pipe.
Heat Treatment and Delivery Condition
UNS S31653 is not individually listed in Table 2, so the default solution-annealing practice applies: heat to a minimum of 1900 °F [1040 °C] and cool rapidly. TP316LN is not an H grade, so there is no Table 5 grain-size requirement and no clause 6.2 reheat rule. Pipe is delivered in the solution-annealed condition, and the certificate should state the heat-treatment temperature and cooling method actually used.
Fabricators who hot form or heavily cold work TP316LN bends and fittings should re-anneal to the same practice where the governing code requires it. Cite the ordered edition’s Table 2 default on the enquiry so the mill does not apply a neighbouring grade’s anneal by habit.
Corrosion Resistance
Low carbon is the primary control for intergranular attack in weld heat-affected zones, which is why TP316LN is chosen for welded aqueous and chemical service. Mo 2–3% supports many chloride process duties at the same level as TP316L, and the nitrogen helps maintain a stable austenitic structure. It is not a seawater or 6Mo grade; for warm seawater and aggressive chlorides, a grade such as ASME SA312 UNS S31254 Stainless Steel Pipe belongs in the comparison. SA-312 publishes no corrosion rates, so the actual medium, temperature and crevice geometry still need engineering review.
Intergranular-corrosion testing to A262 or similar is a supplementary requirement and applies only when written on the purchase order, so state the practice and acceptance criteria if your client needs it. The same applies to any pitting or crevice tests requested by the end user.
Applications of SA312 TP316LN Pipe
| Application | Why TP316LN | Buyer note |
|---|---|---|
| Welded aqueous and chemical process piping | C ≤0.035% limits HAZ sensitization | Qualify WPS on TP316LN |
| Lines needing stable austenite with low carbon | N 0.10–0.16% with Mo 2–3% | Released at 75/30 ksi, not 80/35 |
| Projects specifying 316LN by datasheet | UNS S31653 identity on MTC | Report N on every heat |
TP316LN is the specification answer when a project wants L-grade carbon for welded service and still wants nitrogen in the 0.10–0.16% band, without claiming TP316N’s higher strength. It shows up in chemical, pharmaceutical and cryogenic-adjacent piping classes where the owner has standardised on 316LN. Enquiries should state the UNS, the 75/30 ksi row and whether any small-diameter carbon footnote applies to the ordered sizes.
Weldability
Table 6 maps TP316LN to the ER316L family, and a low-carbon consumable should be frozen on the WPS. Avoid ER316H or higher-carbon fillers for aqueous LN service unless engineering has approved them, because they undo the reason for buying the L grade. Qualify the procedure on TP316LN base metal and keep heat input under control; nitrogen does not excuse poor welding practice. Mill longitudinal welds on WLD and HCW pipe are autogenous and use no filler.
Use stainless-only tooling and back-purge root passes where the specification calls for a clean root, and keep consumable lot records with the weld traveler when Section IX or B31 documentation applies. NDE extent for girth welds is a fabrication-code decision, separate from the mill hydro or electric test on each length.
Surface Finishes
Most TP316LN pipe ships pickled and passivated after the solution anneal, which is the normal finish for process piping. Other finishes are order extras and should be stated on the enquiry, together with whether a roughness target applies to the OD, the ID or both.
- Annealed and pickled (standard)
- Bright annealed, by agreement
- Mechanically polished OD, by agreement
- Electropolished ID for hygienic service, by agreement
Inspection and Testing
SA-312 sets the minimum test package for every heat and length of TP316LN. Supplementary tests are only applied when written on the order, so the inspection and test plan should list them before production starts.
- Heat analysis to Table 1, including every element with a limit
- Tension test to the Table 4 row (75 ksi [515 MPa] / 30 ksi [205 MPa])
- Flattening and, for welded pipe, the applicable weld tests
- Hydrostatic or nondestructive electric test on each length
- Visual and dimensional checks to Table 3 and A999
- Optional: product analysis, IGC test, PMI, UT/RT of welds, EN 10204 3.2 witness
Packaging and Shipping
Each length is marked with SA-312 (and A312 when dual-certified), TP316LN / UNS S31653, the manufacturing type, size, heat number and test method. For export, we pack in a way that protects the stainless surface from carbon steel contact and moisture during ocean transit.
- Plastic end caps on every length
- Bundles strapped with non-metallic or protected bands
- Seaworthy wooden cases or crates for polished or thin-wall pipe
- Segregation from sister grades so stencils cannot be mixed
Why Choose SHH STEEL
SHH STEEL works with qualified stainless mills to supply TP316LN to the edition you name, and our job is to make sure what arrives on site matches the datasheet. That starts with reading the enquiry against the actual SA-312 rows—Table 1 chemistry, the 75 ksi [515 MPa] / 30 ksi [205 MPa] Table 4 row and the Table 2 anneal—and flagging mismatches before an order is placed. We are honest where the standard is silent: if Table 6 does not give a clear filler class, we say so rather than inventing one.
- Seamless, welded and HCW TP316LN to SA-312/A312, with dual marking when both editions are ordered
- EN 10204 3.1 MTCs as standard; 3.2 and third-party witness by arrangement
- Full Table 1 reporting, including nitrogen on every heat
- B36.19 schedules plus special OD and wall by agreement
- Export packing and heat traceability from mill to site
Supply Capability
We supply TP316LN pipe from mill production and selected stock, with lead time depending on size, wall and manufacturing type. The table summarises what we can offer; please confirm the details for your order on enquiry.
| Item | Supply |
|---|---|
| Grade | TP316LN / UNS S31653 |
| Standard | ASME SA-312/SA-312M, ASTM A312/A312M (dual by agreement) |
| Routes | SML, WLD, HCW |
| Sizes | ASME B36.19 schedules; special OD and wall by agreement |
| Filler guidance | ER316L (Table 6 family listing) |
| Certificates | EN 10204 3.1; 3.2 by arrangement |
Standard schedules can often ship from stock or short mill runs, while heavy-wall seamless and special sizes need a rolling slot. Send the edition, grade and UNS, size list, quantities and required date, and we will separate stock lengths from made-to-order items in our quotation so your site dates are realistic.
FAQ
-
Is ASME SA312 the same as ASTM A312?
- For chemistry, tensile requirements, manufacturing types and most testing language, ASME SA-312/SA-312M matches ASTM A312/A312M of the referenced edition. Dual SA312/A312 marking for TP316LN is common when ordered. Name both editions on the purchase order and the certificate so inspectors can verify the heat against the exact books you cited; a bare market stamp does not prove dual certification.
-
What is the UNS number for TP316LN?
- Table 1 lists TP316LN as UNS S31653. Use that UNS on the purchase order, the stencil and the MTC so the chemistry and tensile rows stay unambiguous. When a project mixes plate, fittings and pipe, carry the same UNS language across all forms, but still order pipe to SA-312/A312 rather than to a plate specification.
-
TP316LN vs TP316L — which should I order?
- Both cap carbon at 0.035%, but TP316LN adds a required N 0.10–0.16% and is released against 75/30 ksi, while TP316L has no nitrogen requirement and uses its own Table 4 row. Order TP316LN when the datasheet or owner standard names it; otherwise TP316L is easier to source. Do not accept 316L heats as 316LN unless nitrogen is reported inside the band.
-
TP316LN vs TP316N — which should I order?
- The nitrogen band is the same, but TP316LN caps carbon at 0.035% and is released at 75/30 ksi, while TP316N allows C up to 0.08% and is released at 80/35 ksi. Choose LN for welded aqueous service where sensitization matters, and TP316N when the design depends on the higher strength. The grades need separate inspection and test plans.
-
Seamless vs welded TP316LN — which is better?
- Neither is universally better. Seamless suits small-bore, thick-wall and pressure parts where the piping class excludes welds, while welded and HCW pipe are economical for larger sizes and offer good wall consistency. Choose the route your design code and datasheet allow, state SML, WLD or HCW on the order, and confirm the same letters on the marking and certificate.
-
Hydrostatic test vs NDE — which do I get?
- Each length of TP316LN is either hydrotested or nondestructively electrically tested, and the manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification requires one method, state it on the order and check that the chosen test appears on the certificate for every length; a silent mill choice is not an approved project method.
-
What heat treatment applies to TP316LN?
- UNS S31653 is not individually listed in Table 2, so the default solution anneal at a minimum of 1900 °F [1040 °C] with rapid cooling applies. TP316LN is not an H grade, so there is no Table 5 grain-size rule. Delivery is in the solution-annealed condition, and the certificate should state the temperature and cooling used so the record is complete.
-
What Table 1 chemistry defines TP316LN?
- Table 1 for UNS S31653: C ≤0.035%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00% and N 0.10–0.16%. These are melting-analysis limits from the ordered edition, so do not invent tighter catalogue windows. When product analysis is needed, order it explicitly through Supplementary Requirement S1 or PO wording, and the A480 tolerances shown in the chemistry section then apply.
-
What are the Table 4 tensile requirements for TP316LN?
- Table 4 minima for TP316LN are 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield, with elongation of 35% longitudinal and 25% transverse. Actual certificate values are usually higher, but design and acceptance use Table 4 unless the order states higher guarantees. Record the row on the datasheet so nobody substitutes a sister grade’s line from memory.
-
What filler metal should I use to weld TP316LN pipe?
- Table 6 maps TP316LN to the ER316L family. Freeze the AWS or EN class on the WPS and PQR before production welding and qualify the procedure on TP316LN base metal. Mill longitudinal welds on WLD and HCW pipe are autogenous, so Table 6 guidance applies only to joints made with filler, not to the mill seam.
-
Why specify nitrogen in TP316LN?
- Nitrogen at 0.10–0.16% stabilises the austenite and partly offsets the strength lost by lowering carbon to 0.035%, so the grade keeps the 75/30 ksi Table 4 row rather than a reduced L-grade line. The practical point for buyers is that nitrogen defines the grade: a heat without a reported N result inside the band is TP316L, not TP316LN.
-
Does the small-diameter carbon footnote apply to TP316LN?
- Some SA-312 editions carry a footnote that adjusts carbon for small-outside-diameter, light-wall L-grade pipe. Whether it applies to a TP316LN order depends on the ordered edition and sizes, so check it on the enquiry rather than assuming. If the project needs C ≤0.035% on every size regardless, write that on the purchase order so the mill cannot rely on the footnote.
Conclusion
ASME SA312 TP316LN (UNS S31653) is low-carbon, nitrogen-bearing 316 pipe: C ≤0.035%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00% and a required N 0.10–0.16%, released against 75/30 ksi Table 4 minima with a Table 2 default 1900 °F [1040 °C] anneal and ER316L-family filler. It is not an H grade and not interchangeable with TP316N or TP316L. State the manufacturing type, schedule or wall, finish and any footnote or supplementary requirements on the enquiry, and ask for the heat certificate with carbon and nitrogen clearly reported. For stock checks, mill certificates or dual SA-312/A312 supply questions, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category.