ASME SA312 TP310Cb Stainless Steel Pipe | SA 312/SA 312M
What is ASME SA312 TP310Cb Stainless Steel Pipe
ASME SA-312/SA-312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. Grade TP310Cb is listed in Table 1 as UNS S31040. The “Cb” suffix means columbium—an older name for niobium (Nb); Footnote M states that niobium and columbium are alternative names for the same element. Commercially the same product may be called SA312 TP310Cb pipe, ASTM A312 TP310Cb pipe, A312 Grade TP310Cb, 310Cb, or 310Nb stainless steel pipe when the purchase order clearly references SA-312 or A312. For pressure piping and code work, cite the full grade designation, the UNS number, and the edition of the standard on the purchase order and on the mill test certificate—do not rely on a bare “310Cb” or “310Nb” market label.
TP310Cb is the niobium-stabilized companion to ASME SA312 TP310S Stainless Steel Pipe in the 25Cr–20Ni (310) family. Table 1 locks carbon at ≤0.08%, sets chromium at 24.0–26.0% and nickel at 19.0–22.0%, lists silicon ≤1.00%, keeps molybdenum as a residual ceiling of ≤0.75%, and requires niobium not less than 10×C and not more than 1.10%. Niobium preferentially forms NbC/Nb(C,N) so chromium stays available for corrosion resistance after welding—the same stabilization logic as 347/321-type grades applied to the hotter 25Cr–20Ni base. Room-temperature Table 4 floors remain 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield. It is not an H grade: there is no 0.04% carbon minimum, Table 5 does not mandate grain-size control, clause 6.2 reheat does not apply, and clause 17 heat-treatment lot marking is not required the way it is for H grades. Table 2 uses the default solution-annealing temperature of 1900 °F [1040 °C] because S31040 is not individually listed. Table 6 shows an ellipsis (“…”) for the AWS filler class of TP310Cb / S31040, so filler selection is by agreement on the WPS—not asserted here as a Table 6 mandate.
SHH STEEL can supply ASME SA312 TP310Cb stainless steel pipe to the edition named on the enquiry, including seamless (SML), welded (WLD), and heavily cold-worked (HCW) routes; ASME B36.19 schedules and special OD/wall by agreement; EN 10204 3.1 mill test certificates that report the niobium value against the 10×C rule; and dual SA-312/A312 marking when the heat analysis, heat treatment, mechanical tests, and marking satisfy both editions named on the purchase order. Confirm NPS, wall or schedule, finish, length practice, and any product-analysis or supplementary tests on enquiry.
Common commercial names and how they map to the ordered product are listed below—use the full SA-312/A312 designation on the purchase order rather than market shorthand alone.
- ASME SA312 TP310Cb / SA-312 Grade TP310Cb — preferred marking language for ASME-code and dual-marked pipe
- ASTM A312 TP310Cb — same grade tables for chemistry and tensile when the ASTM edition is referenced
- UNS S31040 — unified numbering system identity used on MTCs, stencils, and Section II Part D cross-references
- 310Cb / 310Nb stainless steel pipe — market shorthand; confirm Nb ≥10×C and ≤1.10%, C ≤0.08%, Cr 24–26%, Ni 19–22%, and Mo ≤0.75% on the order
TP310Cb is not a drop-in for ASME SA312 TP310S Stainless Steel Pipe, ASME SA312 TP310H Stainless Steel Pipe, ASME SA312 TP310HCb Stainless Steel Pipe, or ASME SA312 UNS S31002 Stainless Steel Pipe on a shared “310” or “25-20” market label—each has its own Table 1 row. Versus TP310S, TP310Cb adds the mandatory niobium rule on the same C ≤0.08% / Cr–Ni window; a 310S heat with accidental residual niobium is not TP310Cb unless it meets the 10×C floor and is certified accordingly. Versus TP310H, TP310Cb is the non-H stabilized grade—no carbon floor of 0.04%, no Table 5 grain-size rule, and no clause 6.2 reheat. Versus TP310HCb (UNS S31041), the HCb grade adds the H-grade carbon range (0.04–0.10%), grain-size control, and reheat while keeping Nb stabilization. Versus UNS S31002, TP310Cb allows C ≤0.08% and Si ≤1.00% with Nb stabilization and a 75 ksi tensile floor, while S31002 is the ultra-low C/Si specialty row (C ≤0.015%, Si ≤0.15%, Mo ≤0.10%, 73 ksi) without Nb. Dual marking within the 310 family is only considered when chemistry and (where applicable) H-grade rules overlap—stabilization alone does not convert a heat. Hub: ASME SA 312/SA 312M.
Manufacturing Types (SML / WLD / HCW)
ASME SA-312 defines three manufacturing routes that may be marked on finished TP310Cb pipe. Selecting the route is a purchase-order decision driven by design code, size range, wall thickness, and inspection preference. It does not change the Table 1 chemistry of UNS S31040—melting must still meet C ≤0.08%, Cr 24.0–26.0%, Ni 19.0–22.0%, Si ≤1.00%, Mo ≤0.75%, and Nb 10×C min to 1.10% max—and every route must still pass through the solution anneal required by SA-312.
- Seamless (SML) — no welding at any stage of manufacture. Seamless is preferred for small-bore furnace and radiant tubing, thick-wall process pipe, and pressure parts when the project specification excludes welded pipe or when piping-class documentation is written around seamless product only. Hot-finished or cold-finished seamless must still be solution annealed to the Table 2 default practice and rapidly cooled.
- Welded (WLD) — automatic welding without filler metal. The weld is finished so that the pipe meets dimensional and mechanical requirements after the final heat treatment required by SA-312. Welded product is widely used for larger NPS process headers and ducts where the code accepts welded austenitic pipe; the plate heat must itself meet S31040 chemistry including the niobium rule.
- Heavily cold-worked (HCW) — welded pipe that is cold worked to a reduction of area of wall and weld of at least 35% before the final anneal, again without filler metal in the longitudinal weld. The weld is radiographed before cold work. HCW is ordered when the buyer wants tighter OD/wall consistency for exchanger bundles and the process controls written into SA-312 for that route.
Each finished length is hydrostatically tested or nondestructively electrically tested; the manufacturer may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser agrees to a system test in lieu of hydrotest. Lot definitions follow clause 11.1. Clause 17 heat-treatment lot marking is not mandatory for TP310Cb (it is not an H grade), but heat identity on the stencil and MTC remains required, and buyers often request lot identity for fabrication traceability. Niobium-bearing melts need controlled melting so Nb meets the 10×C floor without exceeding 1.10%; grouping project sizes onto one heat improves Nb consistency and often helps meet mill minimum order quantities that are higher than for commodity TP310S.
Lead times are typically longer than commodity ASME SA312 TP310S Stainless Steel Pipe because Nb recovery must be controlled and remnant fills from prior Nb heats are less common. Plan procurement early for furnace-coil seamless sizes, and confirm route, edition, and any supplementary tests (S1, S5, S7, S9) before placing a mill order so the certificate matches the design basis. Dual certification to ASME SA312 TP310HCb Stainless Steel Pipe requires the H carbon band, Table 5 grain size, and clause 6.2 reheat—most TP310Cb heats will not qualify. Where creep governs and stabilization is still required, move the conversation to TP310HCb instead of stretching a non-H heat into an H-grade design basis. Where ultra-low C and Si are mandatory for oxidizing aqueous service without Nb, switch to ASME SA312 UNS S31002 Stainless Steel Pipe rather than forcing TP310Cb into that chemistry window.
Chemical Composition of SA312 TP310Cb
Two chemistry layers matter: melting (heat / ladle) analysis—mandatory per heat under ASME SA-312/ASTM A312 Table 1—and product analysis when ordered (Suppl. S1 / PO). SA-312/A312 defer product-analysis tolerances through ASTM A999/A999M §6.3 to ASTM A480/A480M Table A1.1. SHH STEEL reports actual ladle and, when ordered, product values—never unpublished tighter windows. On heat analysis, every certificate must show a niobium value that satisfies Nb ≥10×C and Nb ≤1.10%; spot-check the arithmetic on receipt together with carbon ≤0.08%, chromium 24–26%, and nickel 19–22%.
Melting analysis (heat / ladle analysis) — Table 1
Heat analysis for Grade TP310Cb / UNS S31040 from ASME SA-312/SA-312M (ASTM A312/A312M) Table 1 is summarized below. Values are maximum unless a range is shown; ellipses (…) mean no requirement in the ordered edition.
| Element | TP310Cb / UNS S31040 melting analysis |
|---|---|
| Carbon (C) | ≤ 0.08 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 24.0 – 26.0 |
| Nickel (Ni) | 19.0 – 22.0 |
| Molybdenum (Mo) | ≤ 0.75 |
| Niobium (Nb) / Columbium (Cb) | 10 × C min, 1.10 max |
Source: SA-312 Table 1, TP310Cb / UNS S31040. Footnote M: Nb = Cb. Table cell Nb max = 1.10% (footnote G 1.00 conflict → cell used per pack UNCERTAIN). No nitrogen requirement in Table 1 for this grade.
Chromium drives oxidation resistance; nickel stabilizes austenite at the 25Cr–20Ni balance; the 0.08% carbon ceiling plus Nb stabilization limits sensitization in the weld heat-affected zone; molybdenum is a residual control, not an alloying addition for pitting resistance. The Mo ≤0.75% ceiling is why 310Cb is not a chloride-service substitute for TP316/TP316L or 6Mo grades. Nitrogen is not a Table 1 element for TP310Cb—mills may still report N as information, but absence of N on the MTC is not a Table 1 nonconformance for this grade (contrast ASME SA312 UNS S31002 Stainless Steel Pipe, where N ≤0.10% is required).
Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1
When product analysis is ordered, finished-pipe chemistry shall meet Table 1 as modified by the product-analysis tolerances of ASTM A480/A480M Table A1.1 (via A999 §6.3). The heat-analysis 10×C niobium floor is not relaxed by product tolerance. The verified product-analysis limits for TP310Cb are:
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.08 | 0.01 over | ≤ 0.09 |
| Manganese (Mn) | ≤ 2.00 | 0.04 over | ≤ 2.04 |
| Phosphorus (P) | ≤ 0.045 | 0.010 over | ≤ 0.055 |
| Sulfur (S) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Silicon (Si) | ≤ 1.00 | 0.05 over | ≤ 1.05 |
| Chromium (Cr) | 24.0 – 26.0 | 0.25 under / over | 23.75 – 26.25 |
| Nickel (Ni) | 19.0 – 22.0 | 0.15 under / 0.20 over | 18.85 – 22.20 |
| Molybdenum (Mo) | ≤ 0.75 | 0.05 over | ≤ 0.80 |
| Niobium (Nb) | 10 × C min, 1.10 max | 0.05 over on max (Cb+Ta to 1.50 band) | max ≤ 1.15 product; min by agreement with heat Nb |
Niobium check: on heat analysis, Nb ≥10×C and ≤1.10%. Example: C = 0.05% requires Nb ≥0.50% and ≤1.10%. Product tolerance never relaxes the heat-analysis 10×C floor; the A480 columbium-plus-tantalum band allows 0.05 over on the max (product Nb ≤1.15%). Purchase orders should state whether Ta is reported with Nb. Footnote G vs cell: some footnotes cite 1.00% Nb max for certain grades; the Table 1 cell for TP310Cb prints 1.10 max—this pack uses the cell value and flags the footnote conflict in UNCERTAIN. Vs TP310S: same C/Cr/Ni/Mo/Si pattern plus Nb stabilization. Vs TP310HCb: HCb adds C 0.04–0.10, Table 5 grain size, and clause 6.2; Cb alone does not. Product Cr uses the 0.25 under/over band; Ni uses 0.15 under / 0.20 over.
| Element | TP310S | TP310H | TP310Cb | TP310HCb | UNS S31002 |
|---|---|---|---|---|---|
| C | ≤ 0.08 | 0.04 – 0.10 | ≤ 0.08 | 0.04 – 0.10 | ≤ 0.015 |
| Si | ≤ 1.00 | ≤ 1.00 | ≤ 1.00 | ≤ 1.00 | ≤ 0.15 |
| Mo | ≤ 0.75 | … | ≤ 0.75 | ≤ 0.75 | ≤ 0.10 |
| Nb | … | … | 10×C – 1.10 | 10×C – 1.10 | … |
| N | … | … | … | … | ≤ 0.10 |
| H controls | No | Yes | No | Yes | No |
The side-by-side table above shows why a shared “310” or “310Cb” market label is dangerous: ASME SA312 TP310S Stainless Steel Pipe has no Nb requirement; ASME SA312 TP310H Stainless Steel Pipe adds H-grade carbon and grain rules without Nb; TP310Cb and ASME SA312 TP310HCb Stainless Steel Pipe share the Nb rule but differ on carbon and H-grade controls; ASME SA312 UNS S31002 Stainless Steel Pipe combines ultra-low C with ultra-low Si and Mo and has no Nb. Mills often target carbon well below 0.08% so that the 10×C niobium minimum stays moderate—for example 0.04% C needs only 0.40% Nb minimum—which reduces niobium cost and keeps the alloy easier to hot work. Buyers who need higher carbon for creep-range strength should say so early; those needs usually push the conversation toward TP310HCb instead of raising carbon on a non-H heat. Do not invent Table 1 maxima for Ti, Cu, or Al on TP310Cb. Residual elements not listed in Table 1 are controlled by melt practice and by any purchase-order limits the buyer adds.
Mechanical Properties of SA312 TP310Cb
Room-temperature tensile requirements for TP310Cb / UNS S31040 come from ASME SA-312/ASTM A312 Table 4. Niobium stabilization is a corrosion and weldability feature; it does not raise the room-temperature tensile floor above sister 310 grades. Actual mill values are often higher than the minima, but design still uses Table 4 for ambient checks and the governing code allowables for elevated-temperature design of S31040.
| Property | TP310Cb (S31040) |
|---|---|
| Tensile strength, min | 75 ksi [515 MPa] |
| Yield strength, min | 30 ksi [205 MPa] |
| Elongation | 35% longitudinal / 25% transverse |
| Hardness | No Table 4 maximum |
| Grain size | No Table 5 requirement |
Source: SA-312 Table 4 for TP310Cb / UNS S31040. These floors match ASME SA312 TP310S Stainless Steel Pipe; ASME SA312 UNS S31002 Stainless Steel Pipe is lower at 73 ksi tensile. Elongation follows the Table 4 row for the ordered edition. No Table 5 grain-size requirement (not an H grade).
Base mechanical testing includes tension on a lot basis and flattening (or the alternate bend where the standard permits) typically on 5% of the lot, plus hydrotest or NDE on every length. Elevated-temperature tensile and rupture tests are purchase-order options, not base SA-312 requirements. For pressure-retaining parts, use the governing Section II Part D or project-code allowables for UNS S31040—do not invent values, and do not copy TP304, TP316, or TP310H stress tables into a TP310Cb calculation package unless the heat is dual-certified to an H grade with full H evidence.
Although Table 4 has no hardness maximum, fabricators sometimes set a Rockwell limit for bending or expanding—put any such limit on the PO and verify it on the MTC if required. Like other 310 grades, TP310Cb hardens when cold worked; intermediate anneals may be needed for severe forming, and those anneals must still meet the Table 2 default practice. After long high-temperature service, expect reduced room-temperature ductility from carbides and possible sigma—evaluate before cold repair. For creep-range stabilized design with grain-size control, see ASME SA312 TP310HCb Stainless Steel Pipe rather than stretching a non-H heat into an H-grade application.
Dimensions and Tolerances
Dimensional supply for SA312 TP310Cb pipe follows ASME B36.19 schedules for common NPS/schedule combinations, with special OD and wall by agreement when furnace tubes, radiant coils, or process heaters need a non-standard section. Outside-diameter variations follow ASTM A999/A999M; wall-thickness variations follow SA-312 Table 3 as summarized below. State whether wall is nominal or minimum (Suppl. S8) on the purchase order so the mill does not ship the wrong interpretation.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
Source: SA-312 Table 3; outside diameter variations per A999/A999M.
- Lengths — NPS 1/8–8 commonly furnished up to 24 ft unless otherwise agreed; SRL, DRL, or cut-to-length on order
- Cut lengths — never short; typically ≤1/4 in. [6 mm] over unless the PO states a tighter band
- Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen. Threaded TP310Cb is uncommon for high-temperature service
Furnace and radiant coils often need non-standard walls. Special OD × wall combinations should state whether the wall is minimum under tolerance or nominal before the pierce and roll sequence is set. Straightness, end finish, and length tolerance should be written explicitly for export projects so receiving inspection has a clear acceptance basis. For socket-weld or threaded ends on thin schedules, confirm the wall remains adequate after the 12.5% under-tolerance. Jointers are not permitted unless the purchase order expressly allows them; cut-to-length programmes should include an allowance for fit-up scrap so the mill does not ship under-length pieces. Mass tolerance, OD, and wall bands follow the same A999/Table 3 framework used for other SA-312 austenitics.
Equivalent Grades
Equivalence for TP310Cb is primarily an ASME/ASTM identity question. The governing pipe designation is ASME SA-312 TP310Cb / UNS S31040; market names and plate counterparts must be mapped back to that row before a mill is asked to dual-mark or substitute.
| Designation | Notes |
|---|---|
| SA-312 / A312 TP310Cb / UNS S31040 | Governing for this pack |
| ASTM A312 TP310Cb | Identical chemistry when editions align |
| 310Cb / 310Nb (trade) | Confirm Nb 10×C–1.10 on MTC; not an SA-312 grade name by itself |
| SA-240 / A240 S31040 | Plate/sheet counterpart when listed—not a pipe specification by itself |
| EN / JIS | No one-to-one equivalent asserted in this pack—recheck limits if dual-marking is requested |
Related SA-312 grades on steelspecs.com: ASME SA312 TP310S Stainless Steel Pipe, ASME SA312 TP310H Stainless Steel Pipe, ASME SA312 TP310HCb Stainless Steel Pipe, ASME SA312 UNS S31002 Stainless Steel Pipe, ASME SA312 TP309Cb Stainless Steel Pipe, ASME SA312 TP309S Stainless Steel Pipe, ASME SA312 TP347 Stainless Steel Pipe. Nb and Cb mean the same element—do not treat “310Nb” and “310Cb” as different alloys on the purchase order. Versus ASME SA312 TP310S Stainless Steel Pipe, TP310Cb adds mandatory Nb stabilization on the same 25Cr–20Ni / C ≤0.08% base. Versus ASME SA312 TP310H Stainless Steel Pipe, TP310Cb lacks H-grade carbon and grain controls—do not substitute without reviewing the design-code creep basis. Versus ASME SA312 TP310HCb Stainless Steel Pipe, both share Nb, but HCb adds the H-grade carbon band, Table 5, and clause 6.2. Versus ASME SA312 UNS S31002 Stainless Steel Pipe, TP310Cb is the Nb-stabilized commodity-window row, not the ultra-low C/Si specialty. Versus ASME SA312 TP309Cb Stainless Steel Pipe, TP310Cb sits one step higher in Cr/Ni for hotter oxidation service while keeping the same Nb arithmetic. Versus ASME SA312 TP347 Stainless Steel Pipe (stabilized 18-8), TP310Cb stabilizes a 25Cr–20Ni base—they are not substitutes. Dual certification is a mill judgment documented on the MTC—not an automatic entitlement.
Heat Treatment and Delivery Condition
TP310Cb / S31040 is not individually listed in SA-312 Table 2, so the grade follows the Table 2 default of 1900 °F [1040 °C] minimum with rapid cooling. Because TP310Cb is not an H grade, clause 6.2 reheat language does not apply and direct quench after hot forming is accepted. There is no Table 5 grain-size rule. Delivery remains the solution-annealed condition required by SA-312 unless the ordered edition and purchase order state otherwise.
- Solution anneal ≥1900 °F [1040 °C] — Table 2 default; rapid cool
- No Table 5 grain-size rule — not an H grade
- Clause 17 lot marking — not mandatory for TP310Cb; often requested for traceability
- Free of scale and exogenous iron — descaled / pickled or equivalent as ordered
- Bright anneal / passivation — available on request when the end-user specification requires a scale-free or passivated surface
Annealing at the Table 2 default dissolves unwanted phases and redistributes Nb carbonitrides; rapid cooling follows. Owner-specified stabilization heat treatments after fabrication welding—holding in the NbC precipitation range, often around 1650–1750 °F—are purchaser requirements, not SA-312 base rules. Write temperature and time on the PO if needed, and engineer the treatment so it does not conflict with dimensional tolerances or code heat-treatment rules. If a project wants H-grade grain control on a Nb-stabilized 310 chemistry, order ASME SA312 TP310HCb Stainless Steel Pipe instead and accept the carbon minimum and lot-marking rules. Cite the ordered edition’s Table 2 default practice on the enquiry so the mill does not apply a neighboring H-grade reheat habit to a TP310Cb heat by mistake.
Corrosion Resistance
TP310Cb combines 310-level hot oxidation resistance with improved intergranular resistance after welding. Chromium at 24.0–26.0% and nickel at 19.0–22.0% support continuous service in air and many furnace atmospheres at temperatures where 304/316 scale rapidly; niobium stabilization reduces chromium-carbide sensitization in weld heat-affected zones so the passive film stays intact when fabrication cycles through sensitizing temperatures or sees corrosive condensate on shutdown. SA-312 itself publishes no corrosion rates—service claims need engineering review against the actual gas or liquid chemistry.
- High-temperature oxidation — 24–26% Cr / 19–22% Ni supports hot-air and flue-gas duty where classic 18-8 grades scale rapidly; always defer to the design code’s temperature limits for S31040
- Intergranular / polythionic risk — Nb ≥10×C preferentially forms NbC, leaving chromium available in the HAZ; validate with the project corrosion engineer when shutdown chemistry creates SCC risk
- Aqueous chlorides — Mo ≤0.75% residual—not a duplex, 316, or 6Mo substitute for seawater or concentrated chloride service
- Carburizing / sulfidizing gases — evaluate case by case; specialty grades may be preferred for intentional high-silicon or rare-earth service
- Sigma-phase risk — high-Cr grades can form sigma after long intermediate-temperature exposure; design dwell times accordingly
Verify intergranular resistance with Suppl. S7 (ASTM A262 Practice E) when aqueous exposure after welding is critical, and use Suppl. S9 weld-decay testing when welded pipe must demonstrate comparable weld and base-metal loss rates. Neither test is automatic—order them when the corrosion case needs proof. For nitric-acid or other oxidizing aqueous duties that demand Si ≤0.15% and C ≤0.015% without Nb, specify ASME SA312 UNS S31002 Stainless Steel Pipe rather than TP310Cb. For 6Mo seawater service use ASME SA312 UNS S31254 Stainless Steel Pipe. Compared with ASME SA312 TP310S Stainless Steel Pipe, TP310Cb adds Nb stabilization for welded HAZ integrity; compared with ASME SA312 TP309Cb Stainless Steel Pipe, TP310Cb offers higher Cr/Ni for hotter oxidation while keeping the same Nb arithmetic. Stabilization helps against intergranular attack but does not create seawater pitting resistance.
Applications of SA312 TP310Cb Pipe
Buyers typically select TP310Cb when the project already wants 310-level hot-gas oxidation resistance and the design review adds a welded-HAZ corrosion or polythionic-acid risk that an unstabilized 310S heat cannot answer. The grade earns its keep by protecting weld integrity through thermal cycles rather than by raising the continuous oxidation limit above TP310S.
| Application | Why TP310Cb | Note |
|---|---|---|
| Welded furnace / process lines with sensitizing risk | Nb stabilization | Confirm medium; order S7 if needed |
| Refinery heaters with aqueous shutdowns | 310 oxidation + Nb | Consider HCb if creep design governs |
| Heat-treatment equipment | 25Cr–20Ni oxidation resistance | Carburization may need other alloys |
| Dissimilar transition pieces | 310 dilution plus stability | Document WPS |
| Chemical plant hot-gas lines | Welded fabrication without PWHT | Confirm condensate risk |
For creep-range stabilized service with grain-size control, see ASME SA312 TP310HCb Stainless Steel Pipe. For unstabilized oxidation service without a HAZ case, see ASME SA312 TP310S Stainless Steel Pipe. For ultra-low C/Si oxidizing aqueous duty, see ASME SA312 UNS S31002 Stainless Steel Pipe. Track HAZ-related failures in sister units when deciding between TP310S and TP310Cb—lifecycle cost often favors the stabilized grade when weld repairs and unplanned shutdowns dominate the maintenance record. Typical size mix runs from instrument connections NPS 1/2–2 through process lines NPS 3–8 to large welded ducts NPS 12–24; availability of fittings and flanges in 310Cb chemistry can limit the line list, so confirm companion components before freezing the isometric. When replacing TP310S with TP310Cb in an existing unit, review weld procedures and filler selections—the base-metal change alone does not update the WPS. Enquiry packages should ask for Nb and C on every MTC line and state whether S7 intergranular testing is mandatory.
Weldability
TP310Cb welds with GTAW, GMAW, SMAW, and SAW using practices familiar to fabricators of other 310 grades. Stabilization improves as-welded intergranular resistance in the heat-affected zone, which is the main reason the grade is chosen for welded fabrications that see corrosive media or that cycle through sensitizing temperatures. Mill WLD and HCW longitudinal welds are autogenous (no filler); Table 6 guidance applies to joining with filler, not to the mill seam.
Filler and Table 6: TP310Cb / S31040 is listed with AWS class “…”—no classification is given. Filler selection is by agreement and must be recorded on the WPS. Matching Nb-bearing 310 or 347-type fillers are sometimes used so the weld metal itself stays stabilized; do not assume plain ER310 without niobium preserves full stabilization in the deposited metal. Freeze the AWS (or EN) class on the WPS/PQR before production welds.
- Moderate heat input; clean joints free of oil, paint, and exogenous iron
- Argon shielding and backing gas for GTAW root passes
- Remove heat tint; pickle when aqueous or condensate service follows
- Mill seams autogenous; clause 15 repairs must identify any filler used
Qualify welding procedures to ASME Section IX on S31040 material. A PQR on ASME SA312 TP310S Stainless Steel Pipe does not automatically cover the Nb-bearing grade. Dissimilar welds of TP310Cb to carbon steel still commonly use 309/310-type fillers for dilution control; if the weld must also resist intergranular attack in condensate, decide whether the filler itself needs Nb or whether a barrier butter layer is required, and capture that decision in the WPS. After high-temperature service exposure, clean thoroughly before repair welding and consider whether a local stabilizing treatment is needed after repair—follow producer guidance for Nb-stabilized 310.
Surface Finishes
Surface condition for SA312 TP310Cb pipe is stated on the purchase order. Typical mill finishes available from SHH STEEL supply include the following options:
- Annealed and pickled (AP) — solution annealed, descaled in acid pickle or an equivalent process, producing a matte gray finish common for process and furnace pipe
- Blasted and pickled — often used for heavy-wall seamless where scale removal benefits from blast first
- Bright annealed (BA) — annealed in a protective atmosphere to a brighter surface where the order allows and mill capability exists for the size; temperature must still meet the Table 2 minimum
- As-annealed light oxide — sometimes accepted for furnace parts by agreement when the protective scale will form in service anyway
- Mechanically polished — grit or Ra-controlled polish on OD and/or ID when ordered; polishing does not replace solution annealing
- Bead-finished welded OD — weld bead rolled or ground flush as agreed for WLD/HCW product
Passivation after pickle or polish can be added when the end-user specification requires it. Electropolishing is uncommon for furnace service but available for special clean-service needs by agreement. Use low-halide marking inks on high-temperature lines when the project specification bans chloride-bearing inks. State finish, passivation, and any ink restriction on the order so the mill does not ship a default AP finish into a BA or polished requirement.
Inspection and Testing
Base inspection and testing for SA-312 TP310Cb pipe combines chemistry (including niobium arithmetic), mechanical, and integrity checks. The following items form the usual acceptance package; supplementary requirements apply only when written on the purchase order.
- Heat (melting) analysis — mandatory per heat against Table 1 for TP310Cb (UNS S31040), including C ≤0.08%, Cr 24.0–26.0%, Ni 19.0–22.0%, Si ≤1.00%, Mo ≤0.75%, and Nb ≥10×C / ≤1.10%
- Product analysis — when ordered (Suppl. S1 / purchase-order language), using A480 Table A1.1 tolerances via A999 §6.3; useful to confirm Nb and residual Mo on finished pipe
- Tension test — Table 4 tensile, yield, and elongation on a lot basis (75/30 ksi minima)
- Flattening test — or alternate bend where the standard permits (typically on 5% of the lot)
- Hydrostatic test or nondestructive electric test — each length; manufacturer’s option unless the order fixes the method
- Visual and dimensional check — against ordered NPS/schedule or OD/wall and the applicable tolerance clauses
Mill test certificates: EN 10204 3.1 is the standard documentation package from SHH STEEL supply. The certificate must report the niobium value so receiving inspection can verify Nb ≥10×C and Nb ≤1.10%. EN 10204 3.2 or third-party witness (SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency) is arranged when specified and should be booked before final testing. Dual ASME SA-312 / ASTM A312 certification is available when chemistry, heat treatment, mechanical tests, and marking satisfy the edition(s) named on the order.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms Nb and other elements on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S9 weld decay | Compares weld and base-metal loss rates |
| OES / lab Nb | Niobium verification; handheld XRF is limited for Nb |
Receiving review should confirm Nb ≥10×C, Nb ≤1.10, C ≤0.08, Cr 24–26, Ni 19–22, Mo ≤0.75, tensile ≥75 ksi, yield ≥30 ksi, elongation, and hydro or NDE method. Third-party inspectors should verify Nb arithmetic against carbon on the MTC and confirm that the grade stencil reads TP310Cb or S31040—not merely “310.” PMI by OES on a sample length is a useful receiving check when multiple 310 variants share a laydown area. Mechanical tests follow clause 11.1 lot rules; for specialty Nb heats made in short campaigns, a lot may be only a few dozen lengths, so base test frequency is effectively high. Commodity 300-series practice must not override project-specific notes written for TP310Cb on the purchase order.
Packaging and Shipping
Export and domestic shipments of SA312 TP310Cb pipe are packed for handling and ocean or land transport. Typical packing practices from SHH STEEL supply include:
- Seaworthy bundles — pipes strapped or cradled in bundles sized for container or break-bulk handling, with non-metallic separators where needed to protect finish; cradles or individual supports for heavy headers
- End caps / protectors — plastic or metal caps on plain or beveled ends to reduce damage and contamination during transit
- Marking — durable marking of specification, grade (TP310Cb), UNS S31040 when required, heat number, size (NPS or OD × wall / schedule), manufacturing type (SML / WLD / HCW), test letters, and mill identity as required by SA-312 and the purchase order
- Export packing — waterproof wrapping or desiccant as agreed for polished or sensitive finishes; container stuffing photos on request; low-chloride inks on request
Segregate TP310Cb from ASME SA312 TP310S Stainless Steel Pipe, ASME SA312 TP310H Stainless Steel Pipe, and ASME SA312 TP310HCb Stainless Steel Pipe on the packing list and in the yard so stencil mix-ups do not travel with the shipment—mix-ups discovered after fabrication are expensive because the chemistries cannot be converted by heat treatment alone. When TP310Cb ships with TP310S on the same vessel, use separate bundles and distinctly colored tags. Receiving inspectors should compare stencil heat numbers against the MTC for every length and verify that Nb is reported before release to fabrication. Long thin-wall heater tubes are vulnerable to bending in transit; ship them in rigid frames or with close-spaced saddles, and keep interiors dry and capped so chloride-bearing moisture does not stain or pit the surface before installation. Shipment docs typically include packing list, invoice, B/L or AWB, and MTC (3.1 or 3.2) with Nb reported, plus origin/customs papers per Incoterms.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless plate and pipe. For ASME SA312 TP310Cb / UNS S31040 we quote against the edition you name, report the full Table 1 window on the MTC—including C ≤0.08%, Cr 24.0–26.0%, Ni 19.0–22.0%, Si ≤1.00%, Mo ≤0.75%, and Nb ≥10×C / ≤1.10%—and keep heat identity unbroken from melt through finished length. Receiving inspection then clears the heat against Table 1 and Table 4, with the niobium arithmetic checked on every certificate, rather than against a vague “310Cb” catalog sheet. We flag missing Nb fields or failed 10×C arithmetic on supplier MTCs before shipment, so non-conforming paperwork is caught at the mill—not at the fabricator. We also stay honest about Table 6: no AWS filler class is listed for TP310Cb, so filler selection stays by agreement on the WPS. The Footnote G / Table 1 cell conflict on Nb max (1.00 vs 1.10) is disclosed so quality plans adopt the Table 1 cell limit used in this pack.
- Specification fidelity — chemistry and tensile to SA-312/A312 Table 1 and Table 4 for TP310Cb (S31040); Nb reported and checked against 10×C; no unstabilized 310S sold as 310Cb
- Mill resources — SML, WLD, and HCW from qualified stainless pipe mills with heat traceability; cutting and beveling on confirmed orders
- Documentation — EN 10204 3.1 MTCs standard with Nb reported; 3.2 or third-party inspection on request
- Dual marking — ASME SA-312 and ASTM A312 when the heat and tests meet both requirements you name
- Related grades — sister 310-family (TP310S / TP310H / TP310HCb / UNS S31002) and 309Cb SA-312 grades when projects buy matched high-temperature or stabilized packages
- Export packing — seaworthy bundles, end protectors, and durable grade/heat/size/type marking
Quotations follow your purchase-order language for edition year, manufacturing type, size, finish, and any supplementary tests you name (S1, S5, S7, S9). Ask for coordinated plate-and-pipe heats when a project needs matching Nb levels across SA-240 and SA-312 forms. Grade hub: ASME SA 312/SA 312M.
Supply Capability
SHH STEEL can supply ASME SA312 TP310Cb / UNS S31040 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.
| Item | SHH STEEL capability for TP310Cb |
|---|---|
| Standard | ASME SA-312/SA-312M and/or ASTM A312/A312M Grade TP310Cb (UNS S31040) |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD/wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | SRL, DRL, or cut-to-length |
| Finish | Annealed and pickled; blasted and pickled; bright annealed or polished by agreement |
| Testing | Tension, flattening/bend, hydro or NDE per length; Nb arithmetic on MTC; S1/S5/S7/S9 on order |
| Documents | EN 10204 3.1 with Nb reported; third-party inspection / 3.2 on request |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
TP310Cb is less common in distributor stock than TP310S, so mill-run orders are typical and lead times track plate and melt schedules for Nb-bearing 310. Common sizes may occasionally be available from remnant lengths of prior Nb heats; heavy walls and special OD/wall combinations are mill-order items. Enquiries should state the SA-312 edition, TP310Cb / S31040, SML/WLD/HCW, NPS or OD×wall (nominal or minimum), length practice, finish, Nb reporting expectation, and any product-analysis or 3.2 requirements so mill slots align with your need date. Cut lengths, beveling, and packing-list marking are available on confirmed orders. Combining project sizes into one heat improves Nb consistency and helps meet mill minima without over-ordering. For urgent small quantities, ask about remnant lengths from recent Nb heats before authorizing a new melt—remnants can cut weeks from the schedule when sizes match. If the design temperature sits in the creep range and stabilization is still required, ask whether TP310HCb is preferred before finalising the PO—changing after mill production is costly.
FAQ
-
Is ASME SA312 the same as ASTM A312?
- For chemistry (Table 1), tensile (Table 4), manufacturing types, and most testing language, ASME SA-312/SA-312M matches ASTM A312/A312M of the referenced edition. Dual SA312/A312 marking is common when ordered. Name both editions on the purchase order and mill test certificate so inspectors can verify the heat against the exact books you cited—do not assume a bare market grade stamp covers dual certification.
-
What is the UNS number for TP310Cb?
- Table 1 lists TP310Cb as UNS S31040. Use that UNS on the purchase order, stencil, and MTC so chemistry and tensile rows stay unambiguous, and so Nb arithmetic is checked against the correct grade row. When the project mixes plate and pipe, carry the same UNS language across forms, but still order pipe to SA-312/A312—not to the plate specification alone.
-
TP310Cb vs TP310S — which should I order?
- Both share the 25Cr–20Ni / C ≤0.08% window and 75/30 ksi floors; TP310Cb adds mandatory Nb (10×C min, 1.10% max) for stabilization, while TP310S has no Nb requirement. Neither is an H grade. Put the design-code grade and UNS on the datasheet and purchase order before you compare price—switching to TP310S after fabrication drawings are frozen usually means a material change notice, not a free mill substitution.
-
TP310Cb vs TP310H — which should I order?
- TP310H is the creep-service H grade with C 0.04–0.10%, Table 5 grain size, and clause 6.2 reheat, but without a niobium requirement. TP310Cb is the non-H stabilized grade with Nb 10×C–1.10 and C ≤0.08%. They solve different problems—do not treat them as interchangeable on a shared “310” label. Put the design-code grade and UNS on the purchase order before you compare price.
-
TP310Cb vs TP310HCb — which should I order?
- Both require niobium stabilization (10×C min, 1.10% max) on the 25Cr–20Ni base; TP310HCb adds C 0.04–0.10%, Table 5 grain control, and clause 6.2 reheat, while TP310Cb is non-H with C ≤0.08%. Order the datasheet grade. Put the design-code grade and UNS on the purchase order before you compare price—switching after drawings are frozen usually means a material change notice, not a free mill substitution.
-
TP310Cb vs UNS S31002 — which should I order?
- UNS S31002 tightens C to ≤0.015%, Si to ≤0.15%, Mo to ≤0.10%, adds N ≤0.10%, carries a 73 ksi tensile floor, and has no Nb requirement. TP310Cb uses C ≤0.08%, Si ≤1.00%, Mo ≤0.75%, Nb 10×C–1.10, and 75/30 ksi. Order S31002 only when the ultra-low C/Si chemistry is required—a Nb-stabilized 310Cb heat will not meet S31002. Put the design-code grade and UNS on the purchase order before you compare price.
-
Seamless vs welded TP310Cb — which is better?
- Neither is universally better. Choose the manufacturing type your design code and datasheet allow; both are legitimate SA-312 forms when tested to the standard, and both must still meet S31040 chemistry including the niobium rule. State SML, WLD, or HCW on the purchase order and confirm the same letters on the pipe marking and MTC—mixing offers that differ only in manufacturing type is a common bid-evaluation trap.
-
Can you dual-certify SA312 / A312 TP310Cb?
- Yes, when heat analysis (including Nb ≥10×C and ≤1.10%), heat treatment, mechanical tests, and marking meet both editions named on the order. Write the ASME and ASTM edition years on the PO, and require the MTC to reference both books so receiving inspection can clear the heat without a second paperwork chase after shipment. Dual marking with TP310HCb needs the H-grade carbon band and grain-size rules as well—most non-H TP310Cb heats will not qualify.
-
Hydrostatic test vs NDE — which do I get?
- Each length is hydrotested or nondestructively electrically tested. Manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification locks one method, state it on the PO and verify the chosen test appears on the MTC for every length—silent mill option is not the same as an approved project method.
-
What heat treatment / anneal temperature applies to TP310Cb?
- Table 2 does not list TP310Cb individually—use the 1900 °F [1040 °C] default minimum with rapid cooling. It is not an H grade, so clause 6.2 reheat and Table 5 grain-size control do not apply; direct quench after hot forming is accepted. Delivery remains the solution-annealed condition required by SA-312 unless the edition and PO state otherwise. Cite the ordered edition’s Table 2 practice on the enquiry so the mill does not apply a neighboring H-grade reheat habit by mistake.
-
What Table 1 chemistry defines TP310Cb?
- Table 1: C ≤0.08%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 24.0–26.0%, Ni 19.0–22.0%, Mo ≤0.75%, Nb 10×C min / 1.10% max (UNS S31040). Values are melting-analysis limits from the ordered edition—do not invent tighter catalog windows. When product analysis is needed, order it explicitly (Suppl. S1 / PO language) rather than assuming ladle values alone will satisfy receiving inspection.
-
What filler metal should I use to weld TP310Cb pipe?
- Table 6 shows “…” for TP310Cb—filler by agreement. Matching Nb-bearing 310 or 347-type fillers are sometimes used so weld metal stays stabilized; plain ER310 without Nb may not preserve full stabilization in the deposit. Freeze the AWS (or EN) class on the WPS/PQR before production welds, and remember mill WLD/HCW longitudinal welds are autogenous—Table 6 guidance applies to joining with filler, not to the mill seam.
Conclusion
ASME SA312 TP310Cb (UNS S31040) is the niobium-stabilized 25Cr–20Ni pipe grade in SA-312: C ≤0.08%, Nb 10×C min to 1.10% max, Cr 24.0–26.0%, Ni 19.0–22.0%, Mo ≤0.75%, with 75/30 ksi room-temperature minima and a default 1900 °F [1040 °C] anneal. It is not an H grade and carries no Table 5 grain-size rule. It is not a drop-in for TP310S (no Nb), TP310H (H-grade carbon and grain-size rules without Nb), TP310HCb (H-grade plus Nb), or UNS S31002 (ultra-low C/Si, 73 ksi, no Nb)—each has its own Table 1 row. Table 6 lists no AWS filler class (filler by agreement). Order the manufacturing type (SML/WLD/HCW), schedule or wall, finish, Nb reporting, and any product analysis or supplementary tests explicitly. For stock checks, mill certificates, or dual SA-312/A312 supply questions, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category on steelspecs.com.