ASTM A213 TP316LNM Stainless Steel Tube | ASTM A213 Stainless Steel - SHH STEEL

ASTM A213 TP316LNM Stainless Steel Tube

ASTM A213 TP316LNM / UNS S31653 (A213 table Grade TP316LN) low-carbon nitrogen-strengthened molybdenum seamless boiler, superheater and heat-exchanger tube — C ≤0.035% (Footnote D to 0.040%), Cr 16.0–18.0%, Ni 10.0–13.0%, Mo 2.00–3.00%, N 0.10–0.16%, Table 4 75/30 ksi, hardness max 192 HBW / 90 HRB, 1900 °F solution anneal with Footnote F. SHH STEEL supplies cold-finished and hot-finished seamless tube with EN 10204 3.1 MTCs that report carbon, nitrogen and molybdenum.
Grade
TP316LNM / UNS S31653 (A213: TP316LN)
Standard
ASTM A213 / A213M
Product form
Seamless boiler / superheater / heat-exchanger tube (cold-finished and hot-finished)
Size
Typical OD × min wall (or average wall) within ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD and ~0.015–0.500 in. [0.4–12.7 mm] wall; other diameters by agreement
Share:
Overview
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASTM A213 TP316LNM Stainless Steel Tube

ASTM A213 / A213M covers seamless ferritic and austenitic alloy-steel boiler, superheater, and heat-exchanger tubes. This article’s commercial / queue title is TP316LNM for UNS S31653 — the same chemistry row the ASTM A213 stainless table prints as Grade TP316LN. The grade sits where three design needs meet on one datasheet: low carbon for as-welded intergranular resistance, nitrogen for recoverable tensile strength, and molybdenum for chloride-leaning corrosion. Melting carbon is capped at 0.035% (Footnote D raises that ceiling to 0.040% for small-diameter or thin-wall tube that needs many drawing passes), nitrogen is locked at 0.10–0.16%, chromium 16.0–18.0%, nickel 10.0–13.0%, and molybdenum 2.00–3.00%. Nitrogen brings Table 4 tensile acceptance back to 75 ksi [515 MPa] / 30 ksi [205 MPa] — the TP316 pair — instead of the lower 70/25 ksi floor that plain A213 TP316L accepts.

SHH STEEL can supply ASTM A213 TP316LNM (TP316LN / UNS S31653) stainless steel tube as seamless cold-finished and hot-finished product in the usual boiler and heat-exchanger OD × wall / BWG band, shipped with EN 10204 3.1 mill test certificates that report carbon, nitrogen, and molybdenum together with the Table 4 tensile and hardness results. Dual A213 / SA-213 marking is offered only when the purchase order asks for both independent standards. Browse the grade family on the A213/A213M hub.

Commercially you will still see 316LN, 316LNM, S31653, or “low-carbon nitrogen Mo HX tube”; on the MTC and stencil we follow the purchase-order grade name and the ASTM table’s TP316LN / UNS S31653 identity. Sister grades under the same ASTM standard include A213 TP316L, A213 TP316N, A213 TP316, A213 TP304LN, and A213 TP316Ti. A213 covers seamless tube only — no welded or HCW manufacturing type — so cold-finished versus hot-finished is the process choice.

Chemical Composition of A213 TP316LNM

Two chemistry layers matter for TP316LNM / TP316LN under ASTM A213. Melting analysis is mandatory for every heat; product analysis on finished tube applies only when Supplementary Requirement wording or the purchase order invokes it through ASTM A1016/A1016M, with tolerances typically from ASTM A480/A480M Table A1.1. Nitrogen analysis method is a matter of agreement (Footnote B). Footnote D is contractual language for this grade: for small diameter or thin walls requiring many drawing passes, a carbon maximum of 0.040% is necessary — confirm the OD/wall trigger on the ordered edition. Nickel is 10.0–13.0% under A213 for S31653, matching TP316N rather than the wider 10–14% band on TP316 / TP316L.

The tables below reproduce the melt limits for UNS S31653 (A213 Grade TP316LN / this series title TP316LNM), the product-analysis limits from A480 Table A1.1 practice, and a short C / N / Mo snapshot against TP316L and TP316N. Later A213 editions place austenitic stainless grades in Table 2 (older editions used Table 1); confirm the ordered edition on the purchase order.

Melting analysis (heat / ladle analysis)

Element TP316LNM / TP316LN (UNS S31653) melting analysis
Carbon (C) ≤ 0.035 (Footnote D: ≤ 0.040 for small OD / thin wall with many drawing passes)
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 16.0 – 18.0
Nickel (Ni) 10.0 – 13.0
Molybdenum (Mo) 2.00 – 3.00
Nitrogen (N) 0.10 – 0.16

Source: ASTM A213/A213M stainless chemistry table for Grade TP316LN / UNS S31653 (public mill / specification PDF excerpt — _ref_a213.txt / A213–13 table text). This steelspecs series titles the product page TP316LNM per QUEUE; the ASTM table name remains TP316LN. Confirm the ordered edition and the PO grade string before stencil release.

Product analysis — A480/A480M Table A1.1 tolerances applied

Element Melting Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.035 0.01 over ≤ 0.045
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 16.0 – 18.0 0.20 under / over 15.80 – 18.20
Nickel (Ni) 10.0 – 13.0 0.10 under / 0.15 over 9.90 – 13.15
Molybdenum (Mo) 2.00 – 3.00 0.05 under / 0.10 over 1.95 – 3.10
Nitrogen (N) 0.10 – 0.16 0.01 under / 0.02 over 0.09 – 0.18

Carbon / nitrogen / Mo snapshot — TP316L / TP316LNM / TP316N

Element TP316L (S31603) TP316LNM (S31653) TP316N (S31651)
C ≤ 0.035 ≤ 0.035 ≤ 0.08
Ni 10.0 – 14.0 10.0 – 13.0 10.0 – 13.0
Mo 2.00 – 3.00 2.00 – 3.00 2.00 – 3.00
N … 0.10 – 0.16 0.10 – 0.16
Table 4 tensile / yield 70 / 25 ksi 75 / 30 ksi 80 / 35 ksi

Read carbon and nitrogen together. Holding C ≤0.035% (or ≤0.040% under Footnote D) reduces chromium-carbide precipitation during welding or slow cooling — the reason exchanger fabricators specify LN/LNM tube for as-welded tube-to-tubesheet service. The 0.10–0.16% nitrogen band then restores tensile capacity so the designer does not have to accept TP316L’s lower 70/25 ksi floor. Versus A213 TP316N, the intentional chemistry change is the L-grade carbon ceiling; versus A213 TP304LN, the intentional additions are molybdenum and the 16–18 / 10–13 Cr–Ni balance.

When product analysis is ordered, finished tube may read C ≤0.045%, Mn ≤2.04%, P ≤0.055%, S ≤0.035%, Si ≤1.05%, Cr 15.80–18.20%, Ni 9.90–13.15%, Mo 1.95–3.10%, and N 0.09–0.18%. Put any tighter project carbon or nitrogen ceiling on the purchase order before the heat is selected.

Mechanical Properties of A213 TP316LNM

Room-temperature tensile acceptance for UNS S31653 under ASTM A213 is 75 ksi [515 MPa] tensile strength and 30 ksi [205 MPa] yield strength (0.2% offset), with elongation of 35% minimum in 2 in. or 50 mm and hardness max 192 HBW / 200 HV or 90 HRB. That is the same tensile/yield pair as TP316 — and five / five ksi above TP316L’s 70/25 ksi floor. Nitrogen recovers the strength that low carbon would otherwise give away. (UNCERTAIN: the public A213–13 Table 4 PDF excerpt used for this series OCR-skips a printed TP316LN / S31653 row between TP316N and TP317; digits above are cross-checked against Peninsular’s A213 TP316LN / S31653 mechanical table and the A312 sister pack — confirm the ordered edition’s Table 4 row on the PO.)

Property TP316LNM / TP316LN requirement (Table 4)
Tensile strength, min 75 ksi [515 MPa]
Yield strength (0.2% offset), min 30 ksi [205 MPa]
Elongation in 2 in. or 50 mm, min 35%
Hardness, max 192 HBW / 200 HV or 90 HRB

Source: ASTM A213/A213M Table 4 practice for UNS S31653 / Grade TP316LN (Peninsular A213 mechanical excerpt + A312 sister cross-check; A213–13 PDF OCR gap labeled UNCERTAIN above). Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or thinner than 0.015 in. [0.4 mm] wall. Flattening and flaring tests are also required on a lot basis.

Designers who assumed they must accept TP316L’s lower tensile floor to get L-grade carbon with molybdenum should re-check whether TP316LNM’s 75/30 ksi pair is available for the same fluid and weld sequence. Do not assume a TP316L certificate clears TP316LNM — nitrogen must be present and reported. When higher tensile (80/35 ksi) is needed without the L carbon ceiling, open A213 TP316N.

Dimensions and Tolerances

Dimensional supply for ASTM A213 TP316LNM is tube language — OD × wall (minimum or average) and commercially BWG / gauge — not ASME B36.19 pipe schedules as the primary size story. Usual A213 sizes run from about 1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD, with minimum wall about 0.015–0.500 in. [0.4–12.7 mm]; other diameters may be furnished when all other requirements are met. Footnote D’s carbon relief for small OD / thin wall with many drawing passes is a chemistry accommodation, not a free pass on dimensional tolerance — still state min versus average wall on the PO.

OD and wall variations follow ASTM A1016/A1016M as invoked by A213. Cold-finished tubes commonly hold tighter OD control; hot-finished tubes allow wider windows. Cold-finished average-wall product is often summarized as ±10% of the specified average wall; minimum-wall product follows the A1016 minimum-wall tables. Confirm the exact rows for the OD and finish route on the ordered edition.

Item Typical A213 TP316LNM dimensional practice
Product form Seamless only (cold-finished or hot-finished)
Usual size band ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD; wall ~0.015–0.500 in. [0.4–12.7 mm] min (or average wall if PO says so)
Wall basis Minimum wall (default commercial practice) or average wall when specified
OD / wall tolerances Per ASTM A1016/A1016M for the finish route and size
Length Cut lengths for HX / boiler bundles, or mill random lengths by agreement
Footnote D note Small OD / thin wall with many draws may use C max 0.040% — chemistry, not a size exemption

Put the cut list, U-bend preference, and end preparation on the enquiry. Minimum wall remains a first-class A213 concept regardless of L/N/Mo chemistry.

Equivalent Grades

Naming around this UNS is the first trap: ASTM A213 prints Grade TP316LN for UNS S31653; this steelspecs A213 series titles the product page TP316LNM per QUEUE to keep the Mo identity visible in the commercial name. Neither nickname replaces the UNS on the MTC. EN and JIS wrought names that point to similar low-carbon nitrogen Mo chemistry families are not automatic substitutes on an A213 certificate.

Designation Notes
ASTM A213 / A213M Grade TP316LN ASTM table grade name for UNS S31653 — governing chemistry / heat-treatment row
TP316LNM (this series title) QUEUE / commercial page title for the same UNS — confirm PO stencil string
UNS S31653 Unified number that ties the names together
ASME SA-213 TP316LN Separate ASME Code Book adoption — dual-mark only when the PO asks
Related L-grade A213 TP316L — C ≤0.035, Mo, no N band; 70/25 ksi
Related N-grade A213 TP316N — same N band, C ≤0.08; 80/35 ksi
Related 304LN A213 TP304LN — L+N without Mo
Related plate A240 / SA240 flat product in the 316LN family — order plate and tube under their own standards

Dual A213/SA-213 marking is a purchase-order option. Agree the stencil grade string (TP316LN vs TP316LNM) before the heat ships so receiving inspection does not reject a correct UNS for a naming mismatch.

Heat Treatment and Delivery Condition

TP316LN / TP316LNM under ASTM A213 is furnished solution treated at a minimum of 1900 °F [1040 °C], then quenched in water or cooled rapidly by other means. The heat-treatment table carries Footnote F for this grade: quench at a rate sufficient to prevent re-precipitation of carbides, as demonstrable by the capability of tubes to pass ASTM A262 Practice E when that test is specified on the purchase order. The manufacturer is not required to run A262 Practice E unless Supplementary Requirement S4 / the PO calls for it. That heat-treatment row applies to both cold-finished and hot-finished seamless tube.

Cold-finished versus hot-finished is a process and dimensional route, not a substitute for the anneal or the Footnote F quench capability. Delivery condition for SHH STEEL TP316LNM is solution annealed and pickled (or bright annealed by agreement), with anneal temperature, quench method, carbon, nitrogen, and molybdenum results on the EN 10204 3.1 certificate. Straightening, cutting, and end finishing follow heat treatment.

No mandatory ASTM grain-size number appears for this grade in the public heat-treatment table. Put A262 Practice E on the purchase order when as-welded IGC demonstration is contractual — low carbon alone does not replace a written corrosion-test requirement.

Corrosion Resistance

TP316LNM inherits molybdenum’s contribution to pitting and crevice resistance from the 316 family while using low carbon to reduce chromium-carbide precipitation at grain boundaries during welding or slow cooling through the sensitizing range, and nitrogen to keep tensile capacity at the TP316 floor. That combination is why buyers step up from A213 TP304LN when chloride-leaning fluids sit beside as-welded tube-to-tubesheet service, and why they step up from A213 TP316L when the designer refuses the 70/25 ksi floor.

ASTM A213 itself does not publish a corrosion-rate table for TP316LN / S31653; selection remains engineering judgment against fluid, temperature, velocity, and inspection philosophy. Footnote F’s A262 Practice E capability is a quench-quality demonstration path when ordered — write S4 / Practice E onto the purchase order so the test is contractual. SHH STEEL will not rank this grade as equal to higher-Mo alloys such as A213 TP317 in severe chlorides — that claim is not supported by the product standard.

Applications of A213 TP316LNM Tube

Because TP316LNM combines low carbon, nitrogen, and molybdenum, it shows up in heat-exchanger bundles with as-welded tube-to-tubesheet joints in chloride-leaning service, process condensers that need Mo plus recoverable tensile strength, and Code-driven lists that already use TP304LN logic but require molybdenum. The table below pairs typical application areas with a selection note so the grade is chosen for weld sequence, fluid, and strength — not only for the LN/LNM nickname on the BOM.

Application area Typical use of TP316LNM tube Selection note
As-welded Mo HX Tube-to-tubesheet joins needing L carbon + Mo + N Put A262 Practice E on the PO when IGC is contractual
Strength above TP316L When 70/25 ksi is too low but L carbon is still required Confirm N 0.10–0.16% on MTC
Higher tensile without L carbon Prefer TP316N at 80/35 ksi Do not stretch LNM into an N-grade strength story
L+N without Mo Stay on TP304LN when Mo is not required Do not treat TP316LNM as a free upgrade of TP304LN
Ti-stabilized Mo instead of L carbon Consider TP316Ti when Ti path is named Different stabilization strategy — not interchangeable by nickname

For Mo without nitrogen open A213 TP316L; for N without L carbon open A213 TP316N; for L+N without Mo open A213 TP304LN on the same A213/A213M hub.

Weldability

TP316LNM tube is often chosen specifically because tube-to-tubesheet and attachment welds will enter service as-welded. Matching or near-matching molybdenum-bearing low-carbon austenitic filler (ER316L / ER316LSi / equivalent covered electrodes) under a qualified WPS is common practice; some fabricators prefer nitrogen-bearing low-carbon deposits when weld-metal strength must track the base metal’s 75/30 ksi floor. Heat input control, interpass limits, and post-weld cleaning remain the fabricator’s responsibility — A213 governs the seamless tube product, not the field or shop weld procedure.

Because A213 product is seamless, there is no mill longitudinal weld to radiograph the way welded pipe standards describe. Focus inspection language on tube integrity (hydro or NDE of each length), tube-to-tubesheet joint quality, and any contractual A262 Practice E result on the base metal. Low carbon improves the as-welded IGC outlook; it does not erase the need for a written corrosion-test requirement when the datasheet demands one. Specify end preparation and surface finish on the tube PO when orbital or clean-service joins are planned.

Surface Finishes

Standard mill delivery for ASTM A213 TP316LNM is solution annealed and pickled, leaving a clean matte finish suitable for most boiler and heat-exchanger tube duty. Bright annealing under protective atmosphere produces a smoother reflective surface used on some clean-process and instrumentation tube lines and must be called out because it changes the heat-treatment route. Light polish or specified Ra on the bore or OD is a commercial or service-center operation on top of A213 product, not automatic with the grade stamp.

When a hygienic or fouling-sensitive exchanger specification quotes an Ra maximum on the bore, put it on the tube purchase order with its own acceptance language and sampling plan. SHH STEEL stencils the agreed grade string (TP316LN or TP316LNM per PO), heat treatment, and heat number as standard requirements; polish, special OD grind, and passivation after fabrication remain commercial extras unless the contract says otherwise.

Inspection and Testing

Lot testing for ASTM A213 TP316LNM / TP316LN follows tension, hardness, flattening, and flaring under A213 / A1016. Chemistry verification must include the ≤0.035% carbon ceiling (or Footnote D 0.040% when applicable), the 0.10–0.16% nitrogen band, the 10.0–13.0% nickel window, and molybdenum 2.00–3.00%. NDE follows the ordered edition and purchaser supplements — hydrostatic testing or non-destructive electric testing of each length is the usual A213 path unless the purchase order states otherwise.

EN 10204 3.1 certificates from SHH STEEL report ladle chemistry with C, N, and Mo, Table 4 tensile and hardness, and heat-treatment condition. When A262 Practice E is ordered under Footnote F / S4, those results appear as specified. Dual A213/SA-213 marking and third-party witness are available when written into the enquiry. A certificate missing nitrogen or molybdenum is not a complete S31653 release package.

Packaging and Shipping

TP316LNM tubes ship in capped or plugged bundles with weather protection matched to the route. Cut lengths for boiler and exchanger bundles are labeled by heat and size; export packing uses cases or steel-frame crates when required.

Marking includes ASTM A213, the agreed grade string (TP316LN / TP316LNM) with UNS S31653, size, heat number, and SHH STEEL identification. Dual SA-213 marking appears only when the purchase order requests it. Packing lists track the same heat numbers shown on the EN 10204 3.1 certificates so carbon, nitrogen, and molybdenum results stay tied to the shipped lengths.

Why Choose SHH STEEL

SHH STEEL treats ASTM A213 TP316LNM / TP316LN as a low-carbon nitrogen-strengthened molybdenum specification product: C ≤0.035% (Footnote D when applicable), N 0.10–0.16%, Ni 10.0–13.0%, Mo 2–3%, and Table 4 75/30 ksi floors are checked together before a heat is offered. Quotations state OD × wall / BWG, wall basis, finish route, stencil grade string, A262 / Footnote F options, and whether dual A213/SA-213 marking is required.

We refuse nickname assemblies that stamp TP316L or TP316N as 316LN/LNM without the missing carbon ceiling, nitrogen band, or molybdenum. EN 10204 3.1 documentation includes C, N, and Mo. Compare sisters on the A213/A213M hub before freezing the exchanger tube list.

Supply Capability

SHH STEEL supplies ASTM A213 TP316LNM (TP316LN / UNS S31653) seamless stainless steel tube in cold-finished and hot-finished routes across the usual boiler, superheater, and heat-exchanger OD × wall / BWG band. Capability below is an enquiry range — not a frozen warehouse SKU or tonnage claim.

Capability SHH STEEL practice for TP316LNM
Product form Seamless cold-finished and hot-finished tube
Standards ASTM A213 / A213M; dual SA-213 when PO asks
Size band Typical within ~1/8 in. ID to 5 in. OD; other diameters by agreement
Wall basis Minimum wall or average wall as specified
Documentation EN 10204 3.1 MTC with C + N + Mo; A262 Practice E / third-party witness on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Stock / Available sizes

SHH STEEL quotes TP316LNM against a stock-and-mill enquiry range rather than a frozen SKU/tonnage list. Representative OD × wall / BWG combinations for boiler and heat-exchanger tube appear below.

Item Typical stock / enquiry range for TP316LNM
Outside diameter 19.05, 25.4, 31.8, 38.1, 42.4, 50.8, 60.3, 76.2 mm (and other boiler/HX ODs on enquiry; through the usual A213 ~5 in. [127 mm] band)
Wall / BWG BWG 10–18 class walls and metric min-wall equivalents; heavier walls by agreement
Common OD × wall examples 25.4 × 2.11 mm; 31.8 × 2.77 mm; 38.1 × 2.77 mm; 42.4 × 3.56 mm; 50.8 × 3.05 mm; 60.3 × 3.91 mm — illustrative, confirm min vs average wall
Length Cut lengths for boiler / exchanger bundles; bends and random mill lengths on enquiry
Special Non-standard OD/wall, bright anneal, dual A213/SA-213, A262 Practice E, agreed TP316LN vs TP316LNM stencil, third-party witness — confirm before heat reservation

Send OD × wall (or BWG), wall basis, finish route, quantity or cut list, marking (A213 or dual A213/SA-213), stencil grade string, and C / N / A262 notes on one enquiry. We confirm C ≤0.035% (Footnote D when applicable), Cr 16–18% / Ni 10–13%, Mo 2.00–3.00%, N 0.10–0.16%, and Table 4 75/30 ksi without inventing fake warehouse codes. Sisters A213 TP316L, A213 TP316N, and A213 TP304LN sit on the same hub.

FAQ

Is ASTM A213 the same as ASME SA-213 for TP316LNM / TP316LN?
No. ASTM A213 / A213M is the ASTM International product specification for seamless boiler, superheater, and heat-exchanger tubes; ASME SA-213 / SA-213M is the separate ASME Code Book adoption. Dual-mark only when the purchase order asks for both names on the stencil and MTC. Chemistry and tensile floors align closely for a given referenced edition, but the standards remain independent documents.
Does ASTM A213 TP316LNM include welded or HCW tube?
No. ASTM A213 covers seamless boiler, superheater, and heat-exchanger tubes only. There is no WLD or HCW manufacturing-type letter under A213. Cold-finished versus hot-finished describes the seamless process route and dimensional tolerances — not a welded product form. Order welded stainless pipe under a different product standard when that form is required.
Why does this page say TP316LNM when ASTM prints TP316LN?
The ASTM A213 stainless chemistry table lists Grade TP316LN for UNS S31653. This steelspecs A213 series titles the product page TP316LNM per QUEUE so the molybdenum identity stays visible in the commercial name. On the MTC and stencil we follow the purchase-order grade string and always report UNS S31653. Agree TP316LN versus TP316LNM on the PO before release so receiving inspection does not reject a correct heat for a naming mismatch.
What is the chemistry of ASTM A213 TP316LNM / TP316LN?
Melting analysis for UNS S31653 is C ≤0.035% (Footnote D: ≤0.040% for small OD / thin wall with many drawing passes), Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 16.0–18.0%, Ni 10.0–13.0%, Mo 2.00–3.00%, and N 0.10–0.16%. Confirm the ordered A213 edition. Carbon ceiling, nitrogen band, nickel window, and molybdenum are all mandatory.
TP316LNM vs TP316L — what does nitrogen add?
Both grades share Mo 2–3% and C ≤0.035% (Footnote D language). TP316L has nitrogen as a no-requirement ellipsis, Ni 10–14%, and Table 4 70/25 ksi. TP316LNM / TP316LN holds N 0.10–0.16%, narrows Ni to 10–13%, and restores tensile/yield to 75/30 ksi. Order LNM when you need L-grade carbon with Mo and refuse the lower L tensile floor.
TP316LNM vs TP316N — when do I need low carbon?
Both share N 0.10–0.16%, Mo 2–3%, and Ni 10–13%. TP316N allows C ≤0.08% and holds Table 4 at 80/35 ksi. TP316LNM keeps C ≤0.035% and uses the 75/30 ksi floor. Choose LNM for as-welded IGC strategy with nitrogen and Mo; choose N when higher tensile is the priority and low carbon is not mandated.
Why is the nickel band 10.0–13.0% on TP316LN instead of 10–14%?
The A213 stainless chemistry table for UNS S31653 prints nickel 10.0–13.0%, matching TP316N, while TP316 / TP316L print 10.0–14.0%. A heat at 13.5% Ni can clear TP316L but fails TP316LN / TP316LNM. Check the nickel ceiling before assuming dual marking from carbon, nitrogen, and molybdenum alone.
What does Footnote D change for TP316LNM carbon?
Footnote D states that for small diameter or thin walls requiring many drawing passes, a carbon maximum of 0.040% is necessary for TP304L, TP304LN, TP316L, and TP316LN. It is a chemistry accommodation for difficult draws, not a size exemption. Confirm the OD/wall trigger on the ordered edition and state it on the PO when you intend to use the 0.040% ceiling.
What heat treatment does A213 require for TP316LNM?
Solution treatment at a minimum of 1900 °F [1040 °C], water quench or other rapid cool under Footnote F quench-capability language. Delivery is solution annealed and pickled unless bright anneal is agreed. Put A262 Practice E on the purchase order when IGC demonstration is contractual — the mill is not required to run Practice E unless S4 / the PO calls for it.
Minimum wall vs average wall for A213 TP316LNM — which should I specify?
Boiler and heat-exchanger datasheets almost always expect minimum wall. Average wall is allowed when the purchase order says so, with A1016/A1016M tolerances for that basis. State wall basis on the enquiry rather than relying on pipe schedule numbers as the primary A213 wall story.
Can I dual-certify TP316LNM with TP316L on the same heat?
Only when one heat simultaneously clears TP316L’s C ≤0.035% and Ni 10–14% window, TP316LN’s N 0.10–0.16% and Ni 10–13% ceiling, Mo 2–3% for both, TP316L’s 70/25 ksi and TP316LN’s 75/30 ksi floors, and hardness for both — and the purchase order asks for dual marking. Do not assume dual marking from a PMI gun that only reads Mo.
Is TP316LNM a substitute for TP316Ti when I want Mo plus weld-zone protection?
Not automatically. TP316Ti uses titanium ≥5 × (C + N) with C ≤0.08% and a 75/30 ksi floor; TP316LNM uses C ≤0.035% plus nitrogen with the same Mo band. They are different stabilization strategies. Choose the path the datasheet names — L+N carbon control or Ti gettering — rather than swapping by nickname. Open A213 TP316Ti when the Ti formula is required.

Conclusion

ASTM A213 TP316LNM covers UNS S31653 — the ASTM table Grade TP316LN — as the low-carbon, nitrogen-strengthened molybdenum seamless stainless steel tube for boiler, superheater, and heat-exchanger service when C ≤0.035%, N 0.10–0.16%, and Mo 2–3% must deliver the Table 4 75/30 ksi floor. SHH STEEL supplies cold-finished and hot-finished seamless tube in the usual OD × wall / BWG band, solution annealed at 1900 °F [1040 °C] under Footnote F quench language, tested to Table 4 75/30 ksi and hardness limits, with carbon, nitrogen, and molybdenum reported on EN 10204 3.1 certificates — dual SA-213 marking only when the purchase order asks.

Contact: admin@steelspecs.com

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X