GB/T 714 Q500qF Bridge Steel Plate Supplier
What is GB/T 714 Q500qF Bridge Steel Plate?
Q500qF is bridge structural steel plate to GB/T 714. Q stands for yield, 500 is the minimum yield in MPa for plate up to 50 mm, q stands for qiao (bridge) and F is the quality grade: Charpy V-notch at −60°C on longitudinal specimens.
Q500q is the strongest grade that can still be bought TMCP or quenched and tempered at up to 130 mm, used on record-span railway and road-rail bridges. The Shanghai–Nantong Yangtze River Bridge, a road-rail cable-stayed bridge with a 1,092 m main span, was the first large project to use Q500qE. Q500q can be supplied TMCP (Pcm ≤0.23%) or QT (CEV ≤0.50%).
Q500qF is Q500q tested at −60°C, where GB/T 714-2025 raises the energy to 54 J for plate over 12 mm. It is the F letter where the 2025 edition starts to scale energy with strength.
The current text is GB/T 714-2025 (published 31 October 2025, effective 1 May 2026). It replaced GB/T 714-2015 completely and was drafted by Ansteel, Valin Xiangtan, Wuyang, Shougang and other plate mills together with the main bridge fabricators.
SHH STEEL (Shanghai Shenghonghe Import & Export Co., Ltd.) is a steel manufacturer and exporter and global steel mill sourcing partner, mill-direct, China origin. We ship Q500qF cut to size with an EN 10204 3.1 or 3.2 certificate. Sister grades are listed under GB/T 714.
Material Specification
| Specification element | Requirement | SHH STEEL compliance |
|---|---|---|
| Standard | GB/T 714-2025 Q500qF | Confirmed |
| Product | Single-rolled plate ≤150 mm; hot-rolled strip and cut plate ≤25.4 mm | Plate |
| Thickness with tensile values | Up to 130 mm for Q500q | Confirmed |
| Minimum yield ReL | 500 MPa ≤50 mm; 480 MPa >50–100 mm | Confirmed |
| Minimum tensile Rm | 630 MPa ≤100 mm (no upper limit in the standard) | Confirmed |
| Elongation A | ≥ 18% | Confirmed |
| Charpy V-notch | −60°C, 54 J (12–100 mm), longitudinal | Confirmed |
| Delivery condition | TMCP, TMCP + tempering, or quenched and tempered (QT) | As ordered |
| Weldability index | Pcm (Table 7) for TMCP; CEV (Table 6) for QT | Printed on MTC |
| Ultrasonic testing | Plate >20 mm: GB/T 2970, Class II or better | Every plate |
| Through-thickness | Z15, Z25 or Z35 to GB/T 5313, when ordered | As ordered |
| Dimensions | GB/T 709 | Confirmed |
| Certificate | GB/T 247; EN 10204 3.1 or 3.2 | As ordered |
Grades often compared with Q500qF are EN 10025-6 S460Q and EN 10025-4 S460ML; the comparison below shows where they differ.
Chemical Composition: Heat Analysis and Product Analysis
Chemistry for Q500qF is fixed at the ladle, but it is verified on plate. GB/T 714 sets the ladle (heat) limits; GB/T 222 sets how far a finished-plate analysis may stray from them.
Table 1 below is the heat (ladle) analysis for Q500qF from GB/T 714-2025 Tables 1, 2, 3 and 4.
| Element | Q500qF TMCP (%) | Q500q quenched and tempered (%) |
|---|---|---|
| C, max | 0.11 | 0.11 |
| Si, max | 0.55 | 0.55 |
| Mn | 0.80 – 1.70 | 0.80 – 1.70 |
| P, max | 0.015 | 0.015 |
| S, max | 0.006 | 0.006 |
| Nb | 0.010 – 0.090 | 0.005 – 0.060 |
| V | 0.010 – 0.080 | 0.010 – 0.080 |
| Ti | 0.006 – 0.030 | 0.006 – 0.030 |
| Als | 0.010 – 0.045 | 0.010 – 0.045 |
| Cr, max | 0.80 | ≤ 0.80 |
| Ni, max | 0.70 | ≤ 0.70 |
| Cu, max | 0.30 | ≤ 0.30 |
| Mo, max | 0.30 | ≤ 0.30 |
| N, max | 0.0080 | 0.0080 |
| B, max | 0.0005 residual (≤0.0014 if C ≤0.10%) | 0.0005–0.0030 may be added |
| H, max | 0.0002 | 0.0002 |
Nb, V, Ti and Al may be added singly or together. Added singly, each must meet the range above; added together, at least one must reach its minimum and Nb + V + Ti ≤ 0.22%.
Table 2 is the product analysis: the limits a check analysis on finished plate is judged against. GB/T 714-2025 clause 7.1.3 calls up GB/T 222 for the permitted deviations.
| Element | Heat limit (%) | Deviation, GB/T 222-2025 Table 1 | Q500qF product analysis (%) |
|---|---|---|---|
| C | ≤ 0.11 | +0.02 | ≤ 0.13 |
| Si | ≤ 0.55 | +0.05 | ≤ 0.60 |
| Mn | 0.80 – 1.70 | ±0.06 | 0.74 – 1.76 |
| P | ≤ 0.015 | +0.005 | ≤ 0.020 |
| S | ≤ 0.006 | +0.005 | ≤ 0.011 |
| V | 0.010 – 0.080 | +0.02 / −0.01 | ≤ 0.100 |
| Ti | 0.006 – 0.030 | +0.02 / −0.01 | ≤ 0.050 |
| Nb | 0.010 – 0.090 | ±0.005 (listed for 0.015–0.060%) | Above 0.060%: agree in contract |
| Cr | ≤ 0.80 | +0.05 | ≤ 0.85 |
| Ni | ≤ 0.70 | +0.05 | ≤ 0.75 |
| Cu | ≤ 0.30 | +0.05 | ≤ 0.35 |
| Als | 0.010 – 0.045 | ±0.003 | Lower limit −0.003 (Table 1 row is for Al ≥0.015%; confirm) |
| Mo | ≤ 0.30 | Not listed in Table 1 | Agree in contract |
| N | ≤ 0.0080 | Listed only for 0.010–0.020% | Agree in contract |
How to read Table 2. Q500q TMCP heats are low-alloy steel, so Table 1 of GB/T 222 applies. Si ≤0.55% is above 0.37%, so +0.05% applies; Mn falls in the 0.80–1.70% band, so ±0.06%. For one heat, an element may deviate in one direction only.
Mechanical Properties
Tensile values follow Table 9 of GB/T 714-2025 for Q500q. Tensile specimens are transverse; round specimens are used above 40 mm. Where yield is not distinct, Rp0.2 replaces ReL.
| Nominal thickness | ReL min (MPa) | Rm min (MPa) | A min |
|---|---|---|---|
| ≤ 50 mm | 500 | 630 | 18% |
| > 50 – 100 mm | 480 | 630 | 18% |
| > 100 – 130 mm | 450 | 560 | 18% |
Impact values follow Table 10, on longitudinal specimens, average of three:
| Letter / test temperature | KV2 ≤12 mm | KV2 >12 – 100 mm | KV2 >100 – 150 mm |
|---|---|---|---|
| F / −60°C | By agreement | 54 J | Not applicable |
One single value may fall below the required average, but not below 70% of it. Plate over 8 mm and under 12 mm is tested with 7.5 mm specimens (75% of the value); 6–8 mm plate with 5 mm specimens (50%). Plate under 6 mm is not impact tested.
180° bend test, transverse: mandrel D = 2a up to 16 mm and 3a above 16 mm; may be omitted when the mill guarantees it. Yield ratio is not mandatory. If the contract asks for it, Annex C recommends ReL/Rm ≤ 0.88 up to 12 mm and ≤ 0.86 above 12 mm for TMCP plate.
Q500qD / Q500qE / Q500qF: Which Quality Grade?
Q500qF is tested at −60°C. It suits Arctic and sub-Arctic bridges, high-latitude rail lines and owners who want the largest toughness margin for fracture-critical members. F is the coldest letter in GB/T 714: Charpy at −60°C, P ≤0.015% and S ≤0.006%. It exists only for Q420q and above (and their NH versions), and its energy rises with strength.
| Grade | Test temp. | KV2 ≤12 mm | KV2 12–100 mm | KV2 >100 mm | P / S max (%) |
|---|---|---|---|---|---|
| Q500qD | −20°C | 80 J | 120 J | 47 J | 0.025 / 0.015 |
| Q500qE | −40°C | 80 J | 120 J | 31 J | 0.020 / 0.010 |
| Q500qF | −60°C | By agreement | 54 J | — | 0.015 / 0.006 |
Note that F energy at Q500q is 54 J, not 120 J: the colder test uses a lower energy that GB/T 714-2025 raises with strength, from 47 J at Q420q/Q460q to 77 J at Q690q. Plate up to 12 mm needs an agreed value.
Q500qF: What Changed from GB/T 714-2015 to GB/T 714-2025
For Q500qF buyers the 2025 edition changes more than the year on the certificate. The points below come from the foreword of GB/T 714-2025 and its tables.
- Yield values above 100 mm were added (450 MPa for >100–130 mm).
- The Mn range for TMCP steel was revised: the minimum is now 0.80%, and the maximum may be raised to 2.00% by agreement.
- CEV and Pcm limits were revised (Tables 6 and 7).
- Tensile strength is now banded by thickness (e.g. lower minimum Rm above 100 mm) instead of one value.
- Impact energy is set by thickness band (≤12 mm, 12–100 mm, >100 mm) in Table 10.
- Yield ratio is no longer a clause value; it is agreed in the contract, with recommendations in informative Annex C.
- Section products were removed; the standard now covers plate and strip only.
- Delivery is TMCP, TMCP + tempering or QT; normalizing is kept only for Q345q/Q370q plate over 100 mm by agreement.
If a drawing cites 2015 and the plate is made to 2025, get the designer’s written acceptance; tensile strength above 100 mm and the yield-ratio basis differ.
Q500qF vs ASTM A709 and EN 10025: Which Grade Matches?
Can Q500qF replace a US or European bridge grade, or the other way round? Strength can match; toughness rules differ in kind, not only in number.
| Property | Q500qF | EN 10025-6 S460Q | EN 10025-4 S460ML | EN 10025-6 S500Q |
|---|---|---|---|---|
| Min. yield (MPa) | 500 (≤50 mm) | 460 (≤50 mm) | 460 (≤16 mm) | 500 (≤50 mm) |
| Tensile (MPa) | 630 min | 550 – 720 | 540 – 720 | 590 – 770 |
| Charpy | 54 J at −60°C (12–100 mm) | Q: −20°C, QL: −40°C, QL1: −60°C | 27 J at −50°C | Q / QL / QL1: −20 / −40 / −60°C |
| Weathering chemistry | No | No | No | No |
ASTM A709 sets Charpy requirements by temperature zone (1, 2, 3) and by member type: non-fracture-critical (T) or fracture-critical (F). GB/T 714 sets one value per letter, so compare the A709 zone with the GB/T 714 test temperature, not grade with grade.
EN 10025-3/-4/-6 grades show yield at the thinnest band; their values fall with thickness. GB/T 714 keeps 500 MPa to 50 mm. EN tensile ranges have upper limits; GB/T 714 gives minimums only.
At −60°C, the 54 J required for Q500qF is a demanding figure; general structural grades rarely prove any toughness that cold. For the C, D and E letters GB/T 714 asks 120 J, several times the 27–40 J typical of GB/T 1591 plate.
Q500qF Delivery Condition: TMCP vs Normalized vs Quenched and Tempered
GB/T 714-2025 clause 3.2 defines TMCP as rolling with the final deformation in a controlled temperature range, including accelerated cooling with or without tempering (self-tempering included) but excluding direct quenching and quench-and-temper. The delivery route must be stated on the certificate.
| Route | Available for Q500qF | Weldability index | Notes |
|---|---|---|---|
| TMCP | Yes | Pcm ≤0.23% (≤50 mm) | C ≤0.11%; up to 130 mm |
| TMCP + tempering | Yes | Pcm | Improves toughness uniformity |
| Quenched and tempered | Yes | CEV ≤0.50% (≤50 mm) | C ≤0.11%; B 0.0005–0.0030% may be added |
| Normalized | No | — | Not listed |
Q500q is the first level where both TMCP and QT are listed. TMCP plate is leaner (Pcm-controlled); QT plate carries more alloy and is CEV-controlled, but its properties are usually more uniform through the thickness. F-letter plate is often TMCP + tempering or, at the top strength levels, QT; ask which route the mill has qualified for −60°C.
Ask for the route on the purchase order. It changes the weldability index, the welding procedure and, for heavy plate, the price of Q500qF.
Welding Q500qF and Fatigue in Bridge Girders
GB/T 714-2025 clause 7.1.2 uses CEV for normalized, QT and TMCP steel with C >0.12%, and Pcm for weathering steel and TMCP steel with C ≤0.12%, both from the heat analysis:
CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15
Pcm = C + Si/30 + Mn/20 + Cu/20 + Ni/60 + Cr/20 + Mo/15 + V/10 + 5B
| Index | ≤50 mm | >50–100 mm | >100–130 mm |
|---|---|---|---|
| Pcm, TMCP (Table 7) | ≤ 0.23 | ≤ 0.25 | ≤ 0.25 |
| CEV, QT (Table 6) | ≤ 0.50 | ≤ 0.55 | by agreement |
Preheat for Q500qF is set by the qualified welding procedure, from the actual index on the certificate, plate thickness, restraint and hydrogen level. Lower actual values than the table caps save preheat time on large girders. At −60°C, both weld metal and HAZ must prove toughness. Expect lower heat input, more passes and consumables qualified at −60°C.
Typical consumables for Q500qF: E62-class consumables (AWS E9018M type).
Fatigue. Welded details govern fatigue life in a bridge, and their fatigue strength is set by detail category, not by yield strength. Higher-strength plate can carry higher stress ranges only if detailing improves too.
Fatigue design follows JTG D64 (highway) and TB 10091 (railway) in China, EN 1993-1-9 in Europe and AASHTO LRFD in the US; fabrication commonly follows TB 10212, JTG/T 3650 or AWS D1.5.
Q500qFZ15, Z25 and Z35: Through-Thickness Plate for Bridges
Through-thickness properties matter wherever a full-penetration weld sits on the face of a plate, such as diaphragm-to-flange joints and cable anchor plates.
GB/T 714 adds the Z level to the end of the designation, for example Q500qFZ25. The test and acceptance follow GB/T 5313 and apply to plate 15 mm and thicker.
| Z grade | Heat sulfur, max (%) | Reduction of area, avg / single (%) |
|---|---|---|
| Z15 | 0.010 | 15 / 10 |
| Z25 | 0.007 | 25 / 15 |
| Z35 | 0.005 | 35 / 25 |
F chemistry limits S to 0.006%, which already meets the Z25 sulfur cap (0.007%). Only Z35 (S ≤0.005%) needs a further step.
Ask your designer which Q500qF plates are loaded through the thickness. Ordering Z35 on everything costs money and time without adding safety. Z options apply across the GB/T 714 bridge steel range.
Equivalent Material Grades
Annex B of GB/T 714-2025 lists foreign grades against each strength level. It is informative: it tells you which families are close, not that the plates are interchangeable.
| Standard | Grade(s) | Fit for Q500qF |
|---|---|---|
| EN 10025-4 | S500M, S500ML | Listed in Annex B |
| EN 10025-6 | EN 10025-6 S500Q, EN 10025-6 S500QL, EN 10025-6 S500QL1 | Listed in Annex B |
| GB/T 16270 | GB/T 16270 Q500F | QT alternative, different toughness rules |
| GB/T 1591 | GB/T 1591 Q500MF | TMCP general structural |
| GB/T 714 (weathering twin) | Q500qNHF | Same strength, weathering chemistry |
Before substituting, compare three things line by line: minimum yield at the actual thickness, the impact test temperature and energy, and the weldability index. For Q500qF, the 120 J impact level and the Pcm/CEV caps are usually the hardest to match.
Q500qF Testing, UT and Certificate
A batch of Q500qF is one grade, one heat, one thickness, one rolling schedule and one heat-treatment condition, up to 60 t. Table 12 of GB/T 714-2025 sets the tests:
| Test | Frequency | Method |
|---|---|---|
| Heat analysis | 1 per heat | GB/T 20066; GB/T 4336 / GB/T 223 |
| Tensile | 1 per batch | GB/T 2975 / GB/T 228.1 |
| Bend 180° | 1 per batch (may be waived if guaranteed) | GB/T 232 |
| Charpy V at −60°C | 3 specimens per batch | GB/T 229 |
| Through-thickness (Z) | 3 specimens per batch, when ordered | GB/T 5313 |
| Ultrasonic | Every plate >20 mm, Class II or better | GB/T 2970 |
| Surface and dimensions | Every plate | Visual and gauges |
Impact retest: if a set fails, three more specimens are taken from the same batch. The average of all six must meet the requirement; two values may be below it, but only one below 70%. At −60°C, mills may need trial heats before the production run; we agree the test plan before accepting the order.
Dimensions
Common Q500qF sizes:
- Thickness: 6 mm – 130 mm under GB/T 714 tensile tables; most orders 10 – 80 mm
- Width: 1500 – 4000 mm, depending on mill and thickness
- Length: 6000 – 18000 mm; longer by enquiry
- Edge: mill edge or cut edge
- Weight: theoretical, 7.85 g/cm³
Deck plate, webs, flanges, diaphragms and stiffeners are cut to drawing. For U-ribs and rolled sections on the same bridge, see steel beam profiles and steel structural profiles.
Tolerances
For Q500qF, thickness tolerance follows GB/T 709 Class B unless the order says otherwise: −0.30 mm at every thickness, with the plus side shown below.
| Nominal thickness (mm) | Width ≤ 1500 mm | Width > 1500 – 2500 mm |
|---|---|---|
| > 8 – 15 | −0.30 / +0.80 | −0.30 / +1.00 |
| > 15 – 25 | −0.30 / +1.00 | −0.30 / +1.20 |
| > 25 – 40 | −0.30 / +1.10 | −0.30 / +1.30 |
| > 40 – 60 | −0.30 / +1.30 | −0.30 / +1.50 |
| > 60 – 100 | −0.30 / +1.50 | −0.30 / +1.80 |
| > 100 – 150 | −0.30 / +2.10 | −0.30 / +2.50 |
Bridge fabricators often ask for Class C (zero minus) on deck and flange plate so section properties are never under the design value. Wider plates follow the heavier GB/T 709 rows; we state them on the offer.
Q500qF Price Factors and How to Order
For Q500qF, the base price follows the market; grade, letter, size and testing extras decide the rest.
| Cost driver | Effect on price |
|---|---|
| Strength level Q500q | Higher levels need more alloy and tighter rolling control |
| Quality letter | Highest extra: −60°C testing, S ≤0.006%, limited mills |
| Delivery route | TMCP / TMCP+T / QT; QT costs more than TMCP |
| Thickness | Over 60 mm and under 10 mm carry size extras |
| Z15 / Z25 / Z35 | Low-sulfur heat, Z test, UT; Z35 costs most |
| Width and length | Over 3000 mm wide or 15 m long needs mill confirmation |
| Quantity per size | Mill minimums per heat and size |
| Inspection and processing | 3.2 witness, profile cutting, blasting, priming quoted per item |
To get a firm quote in one round, send:
- Grade, edition and Z level, e.g. Q500qFZ25 to GB/T 714-2025
- Thickness × width × length and pieces or tonnes
- Delivery route and UT class if beyond Class II
- Certificate type and inspector
- Destination port and Incoterm
We quote plate price, extras and freight line by line. Need another letter? See Q500qD, Q500qE.
Applications
| Sector | Typical Q500qF components |
|---|---|
| Road-rail cable-stayed bridges | Main truss chords and node plates |
| Suspension bridges | Stiffening girder chords |
| Long-span arches | Arch rib flanges |
| Steel pylons | Pylon shell plate and anchor zones |
| Heavy railway bridges | Members where Q460q exceeds 60 mm |
The letter F suits Arctic and sub-Arctic bridges, high-latitude rail lines and owners who want the largest toughness margin for fracture-critical members.
It is the wrong plate for pressure equipment (pressure vessel steel plates), unpainted exposure (weathering steel plates) or ship hulls (shipbuilding steel plates).
Supply Capability and Global Delivery
SHH STEEL sources Q500qF from first-line bridge-plate mills, including drafters of GB/T 714-2025 such as Ansteel, Valin Xiangtan, Jiangyin Xingcheng, Wuyang, Shougang and Xinyu.
- Certificates: EN 10204 3.1 standard; 3.2 with third-party witness (SGS, BV, TÜV or owner’s inspector)
- Tests: tensile, −60°C Charpy, bend, Z test, UT, product analysis
- Processing: CNC plasma and flame cutting, bevelling, drilling, shot blasting and priming
- Terms: FOB Shanghai, CFR, CIF; TT, LC or TT + LC
- Marking: steel-stamped and paint-marked with grade, heat, size and mill, per GB/T 247
We ship GB, ASTM, EN and JIS plate to the Americas, Europe, the Middle East, Southeast Asia and Africa. Q500qF mostly goes to EPC contractors building bridges to Chinese codes abroad.
Lead time: about 45–60 days from mill rolling; Z35, F letter or 3.2 inspection adds about 1–2 weeks. Sea time from Shanghai is about 7–12 days to Southeast Asia and 28–35 days to North Europe.
Why Choose SHH STEEL
As a steel manufacturer and exporter and global steel mill sourcing partner, SHH STEEL buys Q500qF straight from GB/T 714 mills, China origin. No mixed heats, no relabelled plate.
Before shipment we check four lines on every Q500qF certificate: yield and tensile for the actual thickness band, Charpy at −60°C, the CEV or Pcm for the delivery route, and UT results. If one fails, the plate does not ship as Q500qF.
F-letter Q500q is often specified with Z35. Check that the mill can meet S ≤0.005% and −60°C at the same time before you fix the delivery date.
We also tell buyers when another grade fits better. Neighbouring levels are Q460qF and Q550qF. The weathering counterpart is Q500qNHF. Browse more structural steel plates and high strength low alloy plates.
FAQ
-
What is Q500qF steel?
- Q500qF is bridge structural steel plate to GB/T 714-2025. It has 500 MPa minimum yield up to 50 mm, 630 MPa minimum tensile, 18% elongation and Charpy V-notch impact of 54 J at −60°C for 12–100 mm plate. It is delivered TMCP, TMCP + tempering, or quenched and tempered.
-
What impact energy does Q500qF need at −60°C?
- GB/T 714-2025 requires at least 54 J at −60°C on longitudinal specimens for Q500qF plate over 12 mm and up to 100 mm. For plate 12 mm and thinner the value is by agreement. F energy rises with strength: 47 J for Q420q and Q460q, 54 J for Q500q, 60 J for Q550q, 69 J for Q620q and 77 J for Q690q.
-
What is the yield strength of Q500qF?
- Q500qF has a minimum lower yield strength of 500 MPa up to 50 mm and 480 MPa from 50 to 100 mm, and 450 MPa from 100 to 130 mm (GB/T 714-2025 Table 9). Minimum tensile is 630 MPa up to 100 mm. There is no upper tensile limit in the standard.
-
What is the ASTM or EN equivalent of Q500qF?
- Close grades for Q500qF: EN 10025-4 S500M, S500ML / EN 10025-6 S500Q, S500QL, S500QL1 (Annex B). These are close families, not drop-in substitutes; compare yield at thickness, impact temperature and energy, and the weldability index before substituting.
-
Does Q500qF have a yield ratio requirement?
- Not a mandatory one. GB/T 714-2025 clause 7.7 lets the buyer set a yield ratio in the contract. Annex C recommends ReL/Rm ≤0.88 up to 12 mm and ≤0.86 above 12 mm for TMCP plate at the Q500q level.
-
Does steel grade affect fatigue life of a Q500qF bridge girder?
- Very little. Fatigue life of welded bridge details is governed by the detail category and stress range, not by yield strength. Higher-strength plate raises working stress, so detailing and weld quality must improve to keep the same fatigue life.
Conclusion
Q500qF to GB/T 714-2025 is bridge plate with 500 MPa minimum yield, 630 MPa minimum tensile and 54 J Charpy at −60°C for 12–100 mm plate.
It sits between Q460qF and Q550qF in the bridge range, with Q500qD and Q500qE as sister letters. The most common ordering mistake with Q500qF is leaving the Z level, UT class or impact position off the order; add them at enquiry stage, not after rolling.
Our Q500qF certificates carry heat chemistry, weldability index, tensile and Charpy data to EN 10204 3.1 or 3.2. SHH STEEL can add product analysis, Z15–Z35 and witness inspection.
We ship from Shanghai to bridge builders worldwide. Browse the full GB/T 714 range or other high strength low alloy plates.
Ready to order? Send the drawing or cutting list, the certificate type and the destination port. Contact SHH STEEL for a mill-direct quotation on Q500qF bridge steel plate.