ASTM A312 UNS S30601 Stainless Steel Pipe
What is ASTM A312 UNS S30601 Stainless Steel Pipe
A312/A312M is the ASTM product specification for seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. It stands on its own as an ASTM standard, and this page is written against it. UNS S30601 is one of the less common rows in its Table 1, and that is exactly why buyers ask us to spell out what the specification actually fixes for this alloy and what is left to agreement between purchaser and mill.
UNS S30601 takes the high-silicon idea of S30600 one step further. Table 1 lists it by UNS number only, with 5.0–5.6% silicon, 17.0–18.0% chromium, 17.0–18.0% nickel, and carbon held to 0.015%, plus tight limits on manganese, sulfur, nitrogen, and copper. The extra silicon and nickel are aimed at the hottest and strongest sulfuric acid duties, and the Table 4 floor is 78 ksi tensile and 37 ksi yield.
SHH STEEL can supply ASTM A312 UNS S30601 pipe as seamless (SML), welded (WLD), or heavily cold-worked (HCW) product, in ASME B36.19 stainless schedules or special OD and wall by agreement, with EN 10204 3.1 mill test certificates that report the full Table 1 heat analysis, the Table 4 tension results, and the heat-treatment record. Where a purchase order also asks for ASME SA-312 marking, dual marking can be offered on heats that qualify under both documents, but the ASTM grade remains the one this page describes.
Order it as ASTM A312 UNS S30601 and expect the certificate to carry the same designation. Producer trade names are common in acid-plant specifications, and the alloy is sometimes loosely grouped with S30600, but the two have different silicon and nickel ranges and are not interchangeable without the licensor’s agreement. No EN or JIS equivalent is asserted on this page.
If UNS S30601 turns out not to be the right fit, the closest sister pages in the same ASTM series are A312 UNS S30600, A312 UNS S31002, A312 UNS S31050, A312 TP304L, and A312 TP316L. All A312 grades are collected on the A312/A312M hub, so a short list can be compared against one standard before the enquiry goes out.
Manufacturing Types (SML / WLD / HCW)
ASTM A312 allows three manufacturing routes for UNS S30601 pipe, and the route is a purchase-order decision rather than a property of the grade. Whichever route is chosen, the heat must still meet the same Table 1 limits (C ≤0.015%, Mn 0.50–0.80%, P ≤0.030%, S ≤0.013%, Si 5.0–5.6%, Cr 17.0–18.0%, Ni 17.0–18.0%, Mo ≤0.20%, N ≤0.05%, and Cu ≤0.35%), the same Table 4 tension floor, and the same 2010–2140 °F [1100–1170 °C] solution anneal (Table 2, individually listed) with rapid cooling heat-treatment requirement before any length is released.
- Seamless (SML) pierced and hot or cold finished, chosen for heavy wall, high pressure, or owner specifications that exclude a weld seam
- Welded (WLD) formed from flat-rolled product and welded without filler or with filler where the edition allows, economical in thinner walls and larger diameters
- Heavily cold-worked (HCW) welded pipe given at least 35% cold reduction of the weld and base metal before the final anneal, which refines the weld structure toward seamless behaviour
S30601 is among the most specialized rows in A312, so pipe is generally produced to project quantities, and the manufacturing route, size range, and any seam filler should be fixed with the mill before the order is placed. Tell us which route your design code or client specification accepts, because a quotation that leaves the route open forces the mill to choose and can create disputes at receiving inspection.
Chemical Composition of ASTM A312 UNS S30601
The melting analysis in Table 1 is what the heat must meet when it is cast, and it is the first table a reviewer should compare against the mill certificate. For UNS S30601 the defining limits are C ≤0.015%, Mn 0.50–0.80%, P ≤0.030%, S ≤0.013%, Si 5.0–5.6%, Cr 17.0–18.0%, Ni 17.0–18.0%, Mo ≤0.20%, N ≤0.05%, and Cu ≤0.35%. The table below reproduces the Table 1 row as published, with elements carrying no requirement shown as such rather than filled with invented values.
| Element | UNS S30601 melting analysis |
|---|---|
| Carbon (C) | ≤ 0.015 |
| Manganese (Mn) | 0.50 – 0.80 |
| Phosphorus (P) | ≤ 0.030 |
| Sulfur (S) | ≤ 0.013 |
| Silicon (Si) | 5.0 – 5.6 |
| Chromium (Cr) | 17.0 – 18.0 |
| Nickel (Ni) | 17.0 – 18.0 |
| Molybdenum (Mo) | ≤ 0.20 |
| Nitrogen (N) | ≤ 0.05 |
| Copper (Cu) | ≤ 0.35 |
Silicon at 5.0–5.6% is the defining requirement, and nickel at 17.0–18.0% is raised to keep that much silicon in a stable austenitic matrix. Manganese is held in a narrow 0.50–0.80% band, sulfur at 0.013% maximum, nitrogen at 0.05% maximum, and copper at 0.35% maximum, so nearly every line on the certificate is tighter than for a common grade.
Product analysis is a separate check made on the finished pipe, and ASTM A312 refers it to the permitted variations in ASTM A480 Table A1.1. The second table adds those tolerances to the melt limits so you can see the band that a check analysis on the pipe is allowed to fall within when Supplementary Requirement S1 or an owner check is ordered.
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.015 | 0.005 over | ≤ 0.020 |
| Manganese (Mn) | 0.50 – 0.80 | 0.03 under / over | 0.47 – 0.83 |
| Phosphorus (P) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Sulfur (S) | ≤ 0.013 | 0.005 over | ≤ 0.018 |
| Silicon (Si) | 5.0 – 5.6 | 0.15 under / over | 4.85 – 5.75 |
| Chromium (Cr) | 17.0 – 18.0 | 0.20 under / over | 16.80 – 18.20 |
| Nickel (Ni) | 17.0 – 18.0 | 0.15 under / over | 16.85 – 18.15 |
| Molybdenum (Mo) | ≤ 0.20 | No A480 row for ≤0.20% (rows start over 0.20) | Not established—by agreement |
| Nitrogen (N) | ≤ 0.05 | 0.01 over | ≤ 0.06 |
| Copper (Cu) | ≤ 0.35 | 0.03 over | ≤ 0.38 |
Read the product limits as acceptance bounds for a check analysis only. A heat that sits outside the Table 1 melt range is non-conforming even if a later product analysis lands inside the widened band, so the certificate should always show the ladle analysis first. Molybdenum is capped at 0.20%, and A480 Table A1.1 gives no tolerance at that level, so a product-analysis allowance for Mo is by agreement.
Because S30601 is almost always compared with S30600, the next table places the two Table 1 rows side by side.
| Element | S30600 | S30601 |
|---|---|---|
| C | ≤ 0.018 | ≤ 0.015 |
| Mn | ≤ 2.00 | 0.50 – 0.80 |
| P | ≤ 0.02 | ≤ 0.030 |
| S | ≤ 0.02 | ≤ 0.013 |
| Si | 3.7 – 4.3 | 5.0 – 5.6 |
| Cr | 17.0 – 18.5 | 17.0 – 18.0 |
| Ni | 14.0 – 15.5 | 17.0 – 18.0 |
| Mo | ≤ 0.20 | ≤ 0.20 |
| N | … | ≤ 0.05 |
| Cu | ≤ 0.50 | ≤ 0.35 |
Mechanical Properties of ASTM A312 UNS S30601
Table 4 sets the room-temperature tension requirements for UNS S30601: 78 ksi [540 MPa] tensile strength and 37 ksi [255 MPa] yield strength minimum, with elongation of 35% longitudinal / 25% transverse minimum. The table below shows those values in the form used on the specification, and the mill certificate should report actual results against each line.
| Property (Table 4) | UNS S30601 |
|---|---|
| Tensile strength, min | 78 ksi [540 MPa] |
| Yield strength (0.2% offset), min | 37 ksi [255 MPa] |
| Elongation in 2 in. or 50 mm (or 4D), min | 35% longitudinal / 25% transverse |
| Hardness | No maximum listed in Table 4 |
The 37 ksi yield is 2 ksi above S30600, and the tensile floor is the same 78 ksi. As with its sister, strength is rarely what sets the wall; corrosion allowance and the acid licensor’s practice normally govern, and elevated-temperature allowables must come from the code for this UNS.
No hardness maximum is set for this grade in Table 4, so a hardness figure on a certificate is information rather than an acceptance criterion unless your order adds one. If a project specification imposes hardness or impact testing, write it on the purchase order so the mill can plan the test pieces before the pipe is cut.
Dimensions, Tolerances and Stock Sizes
Dimensions for ASTM A312 UNS S30601 pipe are normally ordered by NPS and schedule from ASME B36.19, or by outside diameter and wall where the design calls for a non-standard size. Outside-diameter tolerance and wall tolerance come from the specification itself, and wall is read as nominal unless Supplementary Requirement S8 asks for minimum wall. The permitted variations in wall thickness from Table 3 are shown below by NPS band and wall-to-diameter ratio.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
In practice the under-tolerance of 12.5% is the figure that matters for pressure design, because the designer has already sized the nominal wall with that allowance in mind. The over-tolerance varies with NPS and the wall-to-diameter ratio, which matters more for fit-up and weld preparation than for strength. For UNS S30601, whose higher strength or special chemistry often justifies a lighter or more closely engineered wall, confirm whether your calculation assumed nominal or minimum wall before the order is placed.
Stock / Available sizes. The table below shows the representative size band we quote for ASTM A312 UNS S30601, with example OD × wall combinations taken from B36.19 schedules. It is a supply and stock-enquiry range rather than a promise that every size sits on the floor today: for S30601 nearly all sizes should be treated as mill orders planned against the project schedule, because existing material is rare. Special OD, special wall, and cut lengths are always handled on enquiry.
| Representative size | Example OD × wall | Typical schedules / notes |
|---|---|---|
| NPS 1/2 – 2 | 21.34 × 2.77 mm (NPS 1/2 Sch 40S); 60.33 × 3.91 mm (NPS 2 Sch 40S) | Sch 10S / 40S / 80S; small-bore process and instrument take-offs |
| NPS 2-1/2 – 6 | 88.90 × 5.49 mm (NPS 3 Sch 40S); 168.28 × 3.40 mm (NPS 6 Sch 10S) | Sch 10S / 40S / 80S; the most frequent enquiry band |
| NPS 8 – 12 | 219.08 × 8.18 mm (NPS 8 Sch 40S); 323.85 × 4.57 mm (NPS 12 Sch 10S) | Sch 10S / 40S; confirm SML or WLD route on enquiry |
| NPS 14 – 24 | 406.40 × 4.78 mm (NPS 16 Sch 10S); 609.60 × 9.53 mm (NPS 24 Sch 40S) | Sch 10S / 40S; usually mill-order, mostly welded |
| Special OD × wall | Any OD and wall the mill can qualify | On enquiry: state OD, nominal or minimum wall, and length practice |
Read the example sizes as orientation for writing the enquiry, not as a price list. When you send a size list we check live availability line by line, separate what can ship from existing material from what needs a mill slot, and give the lead time for each group so the purchase order can be split if the schedule demands it.
Equivalent Grades
Buyers often arrive with a trade name, a plate designation, or a European number rather than the A312 row. The table below maps the names we see on enquiries for UNS S30601, but only the ASTM A312 grade and UNS number are contractual on this page; everything else is a cross-reference that needs checking against its own standard.
| Designation | Notes |
|---|---|
| ASTM A312 UNS S30601 | Governing grade on this page (no TP name) |
| ASME SA-312 UNS S30601 | Separate Code standard; dual mark only when the order names both |
| ASTM A312 UNS S30600 | Lower-silicon sister; not interchangeable without review |
| Producer trade names | Order by UNS S30601, not by trade name |
| EN / JIS | No one-to-one equivalent asserted |
The ASME SA-312 row is listed because some Code projects require it, not because it is a synonym. ASME SA-312 is a separate standard adopted into the Boiler and Pressure Vessel Code, and the SA312 UNS S30601 page covers that document on its own terms. When both marks are wanted, the order should name both specifications and their editions so the certificate can state compliance with each.
Heat Treatment and Delivery Condition
Table 2 lists S30601 individually with a solution-annealing window of 2010–2140 °F [1100–1170 °C], followed by water quenching or rapid cooling. The high temperature is needed to dissolve silicon-rich phases in a 5% silicon alloy, and both upper and lower limits are binding, so a certificate showing an anneal outside the window is non-conforming. Seamless pipe may be quenched directly after hot forming only when its temperature is within the requirement.
Delivery condition for UNS S30601 is solution annealed, then descaled by pickling or by blasting and pickling, straightened, and cut to the ordered length practice. HCW pipe receives its cold reduction before the final anneal, so cold work is never the delivered condition. Ask for the actual annealing temperature and cooling method to be recorded on the certificate, because a reviewer cannot otherwise confirm the Table 2 requirement from the document alone.
Corrosion Resistance
ASTM A312 contains no corrosion table, so the following is engineering commentary rather than a specification requirement. S30601 is designed for hot, strong sulfuric acid and oleum service, where its 5.0–5.6% silicon builds a protective silica-rich film that lower-silicon alloys cannot sustain. Claims about specific acid strengths and temperatures come from the alloy producers and acid-plant licensors, and they should be confirmed for each project rather than taken from a general page.
The ultra-low carbon and nitrogen limits keep welded joints resistant to intergranular attack in oxidizing acid. The alloy is not intended for chloride-bearing water, reducing acids, or general chemical service, and using it outside its design niche wastes a scarce and costly material.
Applications of ASTM A312 UNS S30601 Pipe
Applications for ASTM A312 UNS S30601 pipe are almost entirely in sulfuric acid production and handling. The table below gives the typical roles we see on enquiries.
| Application | Role of S30601 | Note |
|---|---|---|
| Sulfuric acid plant strong acid circuits | Acid distributors, pump discharge, tower inlet and outlet lines | Typically replaces cast iron or brick-lined designs |
| Absorption and drying towers | Internal distributor pipes and headers | Velocity and temperature limits apply |
| Acid coolers | Connection piping to plate or shell-and-tube coolers | Some coolers are anodically protected |
| Oleum handling | Transfer and process lines | Confirm concentration range with producer |
| Strong nitric acid service | Process lines where high-Si austenitic is chosen | Low C critical |
| Metallurgical acid plants | Strong acid sections | Impurity levels influence life |
Treat the table as a starting point for discussion with the process licensor or corrosion engineer, not as an approval. Code allowable stresses, temperature limits, and any owner material lists decide whether UNS S30601 is acceptable on a given line, and those checks should be made before the pipe is ordered rather than after it arrives.
Weldability
S30601 requires careful welding: low heat input, tight interpass control, and clean conditions, because high-silicon austenitic weld metal is prone to hot cracking. Table 6 shows S30601 with no AWS class and no filler UNS, so no filler is specified by the standard and the consumable is by agreement. Producers supply matching fillers for this chemistry, and the procedure should be qualified on S30601 with the producer’s guidance on joint design and post-weld cleaning.
Qualify the procedure on UNS S30601 itself rather than on a convenient 304 coupon, because the qualification has to demonstrate the strength and soundness of this chemistry. Clean joint preparation, controlled heat input and interpass temperature, and a back-purged root are the normal baseline; the certificate for any WLD pipe should also state whether filler metal was used in the longitudinal seam.
Surface Finishes
Surface condition for ASTM A312 UNS S30601 pipe should be stated on the purchase order rather than left to mill default. On stainless pipe, residual scale, embedded free iron, and chloride contamination from handling can matter as much as the nominal finish name, and they are far easier to prevent at the mill than to correct on site.
- Annealed and pickled the standard delivery after solution treatment for process piping
- Blasted and pickled when heavier scale needs mechanical help before chemical descaling
- Bright annealed by agreement, generally on smaller sizes where the furnace atmosphere can be controlled
- Passivated or polished by agreement, with the method and acceptance criteria written on the order
For UNS S30601, a fully pickled surface free of embedded iron is the normal requirement, since free iron can initiate attack in hot acid. If the line will be inspected for surface iron, specify the test method at the enquiry stage so that the packing and handling plan supports it.
Inspection and Testing
The base acceptance package for ASTM A312 UNS S30601 pipe combines heat analysis, tension testing, the flattening or bend test that applies to the manufacturing type, and a hydrostatic or non-destructive electric test on every length. Visual and dimensional inspection confirm the size and surface before marking. For S30601 we recommend checking silicon, nickel, manganese, sulfur, nitrogen, and copper line by line, and confirming the anneal temperature inside the 2010–2140 °F window.
Supplementary requirements are optional until they are written on the order. The options buyers request most often for this grade are summarized below, and each one adds test time that should be allowed for in the delivery schedule.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms chemistry on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S8 minimum wall | Wall interpreted as minimum rather than nominal |
| S9 weld decay | Compares weld and base-metal loss rates |
Third-party inspection, witness points, and EN 10204 3.2 certification are available when the order names the inspection agency. Agree the hold points before production starts, because witnessing a hydrotest or a tension test after the fact is not possible.
Packaging and Shipping
ASTM A312 UNS S30601 pipe is packed for handling and for ocean or land transport. Each length is marked with ASTM A312, the grade UNS S30601, the manufacturing type, size, heat number, and the test method used, with SA-312 added only when the order asks for dual marking. Bundle lists repeat the heat numbers so receiving can match pipe to certificates without opening every wrap.
- End caps or bevel protectors fitted as ordered
- Bundles strapped with protected contact points to limit iron pick-up
- Wooden cases or seaworthy bundles for export, with moisture protection for sea freight
- Small-bore or polished pipe cased separately where damage risk is higher
Stainless pipe should not be stored or lifted in contact with carbon steel, and for a specialty grade such as UNS S30601 it is worth keeping the material segregated by heat on arrival, since mixing it with common 304 stock is the most frequent cause of misuse on site.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless pipe, and for a specialty grade such as ASTM A312 UNS S30601 we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 heat analysis, the Table 4 tension results, and the heat-treatment record, and we tell you early when a size or route is a mill order instead of letting the lead time surprise you.
- Experience with UNS-only acid-plant alloys whose certificates need every tight Table 1 line reported
- Clear advice on sister grades under ASTM A312, so UNS S30601 is not confused with a commoner alloy that looks similar on paper
- Honest separation of specification requirements from producer or market guidance in every document we send
- EN 10204 3.1 certificates as standard, with third-party inspection and 3.2 certification on request
The aim is a delivery that clears receiving inspection on the first review. That means the certificate, the stencil, and the purchase order all say the same thing about grade, UNS number, manufacturing type, size, and heat treatment, and that any agreed variation is written down before the pipe is made.
Supply Capability
SHH STEEL can supply ASTM A312 UNS S30601 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade, and each line can be narrowed to your project specification.
| Item | SHH STEEL capability for UNS S30601 |
|---|---|
| Standard | ASTM A312 / A312M, UNS S30601 |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD and wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | Single random, double random, or cut to length |
| Heat treatment | 2010–2140 °F [1100–1170 °C] solution anneal (Table 2, individually listed) with rapid cooling |
| Filler guidance | No filler specified in Table 6; by agreement (producer matching consumable) |
| Testing | Tension (78/37 ksi), flattening or bend, hydrostatic or electric test per length; S1, S5, S7, S8, S9 on order |
| Documents | EN 10204 3.1 with full Table 1 analysis; 3.2 and third-party inspection on request |
| Trade terms | FOB, CFR, CIF, EXW and other agreed Incoterms |
Stock / Available sizes. The representative band for UNS S30601 is NPS 1/2 to 24 in Sch 10S, 40S, and 80S as listed under Dimensions. Selected common OD × wall combinations may be available from existing material, while heavy-wall seamless, unusual schedules, and special cut lengths are normally mill orders. We do not publish stock part numbers or tonnage claims for this grade; ask for a live check against your size list instead.
Enquiries move fastest when they state the A312 edition, UNS S30601, the manufacturing type, NPS or OD × wall (and whether the wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements. Dual SA-312 marking, bevelled ends, and cut lengths are available on confirmed orders when the order says so.
FAQ
-
Is ASTM A312 UNS S30601 the same as ASME SA-312 UNS S30601?
- They are two independent standards. ASTM A312/A312M is the ASTM product specification, and ASME SA-312 is the separate document adopted into the Boiler and Pressure Vessel Code. The technical rows for UNS S30601 are closely aligned in current editions, but a pipe is only certified to the document named on the order, so when both are needed the purchase order should list both specifications and editions and the certificate should state compliance with each.
-
What is the UNS number for ASTM A312 UNS S30601?
- This alloy carries no TP name in A312 Table 1; it is ordered as UNS S30601. The UNS number should appear on the mill certificate and on the stencil next to the ASTM A312 mark, because a trade name alone makes it hard for receiving inspection to tie the chemistry on the certificate to the pipe in the rack.
-
What are the tensile and yield requirements for ASTM A312 UNS S30601 pipe?
- Table 4 requires 78 ksi [540 MPa] tensile strength and 37 ksi [255 MPa] yield strength minimum, with elongation of 35% longitudinal / 25% transverse minimum. These are room-temperature minimums for acceptance only; design allowables at temperature come from the applicable piping code, and they should be checked there before a wall thickness is fixed.
-
What heat treatment does ASTM A312 UNS S30601 pipe receive?
- S30601 is individually listed in Table 2 at 2010–2140 °F [1100–1170 °C], followed by water quench or rapid cooling; the 1900 °F default does not apply. The delivered condition is solution annealed and descaled, and the certificate should record the actual annealing temperature and the cooling method so a reviewer can confirm the requirement without asking the mill.
-
Which filler metal is used to weld ASTM A312 UNS S30601?
- Table 6 lists S30601 with no AWS A5.9 class and no filler UNS, so the standard specifies no filler and the choice is by agreement; producers offer matching high-silicon consumables for this alloy. Whatever is chosen should be recorded on the WPS and PQR, and the procedure should be qualified on UNS S30601 base metal so that the joint strength and soundness are demonstrated on the real chemistry.
-
Is ASTM A312 UNS S30601 pipe available seamless and welded?
- Yes. ASTM A312 allows seamless (SML), welded (WLD), and heavily cold-worked (HCW) pipe for UNS S30601, all meeting the same chemistry, tension, and heat-treatment rules. Seamless is usual for heavy wall and high pressure, while welded is often more economical in thin walls and larger diameters; state the accepted route on the order.
-
What sizes of ASTM A312 UNS S30601 pipe can SHH STEEL supply?
- We quote NPS 1/2 to 24 in Sch 10S, 40S, and 80S as the representative band, plus NPS 1/8 and up and special OD and wall by agreement. Some common sizes may be available from existing material, while heavy-wall seamless and unusual schedules are normally mill orders, so send a size list for a live check.
-
What documents come with ASTM A312 UNS S30601 pipe?
- Each shipment carries an EN 10204 3.1 mill test certificate showing the A312 edition, UNS S30601, manufacturing type, heat number, the full Table 1 heat analysis, Table 4 tension results, heat treatment, and the hydrostatic or electric test. Third-party inspection and 3.2 certification can be added when the order names the agency.
-
Why does UNS S30601 contain so much silicon?
- The 5.0–5.6% silicon is what lets the alloy form a protective silica-rich film in hot, strong sulfuric acid, which is its design purpose. Nickel is raised to 17.0–18.0% to keep that much silicon in a stable austenitic structure, and carbon is held to 0.015% to protect welds.
-
Is UNS S30601 better than UNS S30600?
- Neither is better in general; they target different acid conditions. S30601 has higher silicon and nickel and is aimed at the more severe end of strong sulfuric acid service, while S30600 covers a wider range of oxidizing-acid duties. The acid licensor’s grade list should decide.
-
Can UNS S30601 pipe be welded in the field?
- It can, but with care. High-silicon weld metal is sensitive to hot cracking, so low heat input, controlled interpass temperature, clean joints, and a procedure qualified on S30601 are essential. Table 6 specifies no filler, so the matching consumable must be agreed and recorded on the WPS.
Conclusion
ASTM A312 UNS S30601 (UNS S30601) is the highest-silicon alloy of the series, built for hot strong sulfuric acid and oleum, with a 2010–2140 °F Table 2 anneal and a 78/37 ksi floor. The specification fixes C ≤0.015%, Mn 0.50–0.80%, P ≤0.030%, S ≤0.013%, Si 5.0–5.6%, Cr 17.0–18.0%, Ni 17.0–18.0%, Mo ≤0.20%, N ≤0.05%, and Cu ≤0.35%, a Table 4 floor of 78 ksi [540 MPa] tensile and 37 ksi [255 MPa] yield, and 2010–2140 °F [1100–1170 °C] solution anneal (Table 2, individually listed) with rapid cooling heat treatment, while filler selection is by agreement because Table 6 specifies no filler for S30601. Put the manufacturing type, size and wall basis, finish, and any supplementary tests on the purchase order, and review the EN 10204 3.1 certificate against Tables 1, 2, and 4 before release. SHH STEEL can supply ASTM A312 UNS S30601 pipe to the edition you name; compare sister grades on the A312/A312M hub, or send your size list to admin@steelspecs.com.