ASME SA312 UNS S30601 Stainless Steel Pipe | SA 312/SA 312M
What is ASME SA312 UNS S30601 Stainless Steel Pipe
ASME SA-312/SA-312M (identical in its grade tables to ASTM A312/A312M) covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe for high-temperature and general corrosive service. UNS S30601 is listed in Table 1 with no TP designation, so it is purchased, stencilled, and certified by UNS number only. It is the highest-silicon austenitic stainless steel in the specification, and the Code row—not a producer brand or a “5% silicon stainless” description—is what the heat has to be checked against.
Table 1 sets silicon 5.0–5.6%, chromium and nickel both at 17.0–18.0%, carbon ≤0.015%, a narrow manganese window of 0.50–0.80%, phosphorus ≤0.030%, sulfur ≤0.013%, and residual limits of Mo ≤0.20%, N ≤0.05%, and Cu ≤0.35%. Table 4 requires 78 ksi [540 MPa] tensile and 37 ksi [255 MPa] yield minimum with 35% longitudinal / 25% transverse elongation. Table 2 lists S30601 individually at 2010–2140 °F [1100–1170 °C] with rapid cooling. S30601 does appear in Table 6, but the AWS class and filler UNS columns show only ellipses, so no filler is specified and selection is by agreement. It is not an H grade.
The alloy was developed for the hardest end of hot, strong sulfuric acid service: acid towers, distributors, and circulation lines where temperature and concentration are beyond what conventional stainless steels, and even the lower-silicon ASME SA312 UNS S30600 Stainless Steel Pipe, handle economically. At about 5% silicon the passive film becomes rich enough in silica to stay protective in strong oxidizing acid at high temperature. Silicon is a strong ferrite former, so nickel has to rise to 17–18% to keep the structure fully austenitic and ductile, and carbon is pushed down to 0.015% because any grain-boundary carbide becomes a path for acid attack.
SHH STEEL can supply ASME SA312 UNS S30601 stainless steel pipe to the edition named on the enquiry, as seamless (SML), welded (WLD), or heavily cold-worked (HCW) pipe; in ASME B36.19 schedules or special OD and wall to the licensor’s line list; with EN 10204 3.1 mill test certificates that report the full Table 1 window—Si, the Mn band, S, and the Mo/N/Cu residuals—together with the actual anneal temperature inside 2010–2140 °F; and with dual SA-312/A312 marking when heat, heat treatment, tests, and marking satisfy both editions on the order. Most S30601 is welded from plate, and we confirm sizes and lead time with the mill before quoting.
Names you may meet and how they map to the ordered product:
- ASME SA312 UNS S30601 / SA-312 S30601 — correct Code form; no TP name exists
- ASTM A312 UNS S30601 — ASTM parent with the same chemistry and tensile rows
- “5% silicon stainless” trade names — producer brands exist for this chemistry; order and certify by UNS S30601
- EN / JIS — no one-to-one designation is asserted here; verify against regional standards if a cross-reference is needed
S30601 is not interchangeable with its neighbours. Versus ASME SA312 UNS S30600 Stainless Steel Pipe, it carries more silicon (5.0–5.6% against 3.7–4.3%), more nickel, lower carbon, a controlled manganese band, tighter sulfur, and a 2 ksi higher yield floor—at the price of harder fabrication and higher cost. ASME SA312 UNS S30615 Stainless Steel Pipe shares the high-silicon idea but uses high carbon and aluminium for hot carburizing gases, which is a different job entirely. For ordinary chemical service, ASME SA312 TP304L Stainless Steel Pipe and ASME SA312 TP316L Stainless Steel Pipe remain far more economical. Family hub: ASME SA 312/SA 312M.
Manufacturing Types (SML / WLD / HCW)
ASME SA-312 recognizes three manufacturing routes for UNS S30601 pipe, and the route is a purchase-order decision driven by the design code, the size range, wall thickness, and how the owner wants the pipe inspected. The route never changes the chemistry: whichever way the pipe is made, the heat must still meet the Table 1 window of Si 5.0–5.6%, Cr and Ni 17.0–18.0%, Mn 0.50–0.80%, and C ≤0.015%, and every length must still go through the solution anneal at the Table 2 range of 2010–2140 °F [1100–1170 °C] before it is released.
- Seamless (SML) — no welding at any stage. Preferred for high-pressure service, thick walls, and owners who exclude welded pipe from the design class. Seamless S30601 is uncommon because 5% silicon makes hot piercing and extrusion difficult; expect it only in limited small sizes.
- Welded (WLD) — automatic welding without filler metal, with the weld finished so the pipe meets dimensional and mechanical requirements after the final heat treatment. The strip or plate heat must itself carry the full UNS S30601 chemistry, so ask for the coil or plate heat number on the certificate.
- Heavily cold-worked (HCW) — welded pipe cold worked to at least 35% reduction of wall and weld before the final anneal, again without filler in the longitudinal seam, with the weld radiographed before cold work. Order HCW when the project specifically wants that marking and the process controls SA-312 writes around it.
Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test in place of the hydrotest, and lots for mechanical testing follow clause 11.1. Acid-plant owners usually add product analysis (S1) and full radiography of welded seams (S5), because a leak in strong hot acid is a safety event, not just a maintenance item.
In practice most S30601 pipe is welded from S30601 plate and annealed as a separate operation, and large distributor headers may be rolled and welded from plate into pipe-like sections. Whether those fabricated parts fall under SA-312 or are certified to the plate specification depends on how they are made, so settle that with the licensor and inspector before ordering. Very few mills make this grade; compared with ASME SA312 TP304L Stainless Steel Pipe expect longer lead times, minimum quantities, and tight control of the 2010–2140 °F anneal, which should be reported as an actual temperature on the MTC.
Chemical Composition of SA312 UNS S30601
Heat analysis must meet Table 1. Product analysis (S1) follows ASTM A480/A480M Table A1.1 via A999, with a gap for molybdenum.
Melting analysis (heat / ladle analysis) — Table 1
Heat analysis for UNS S30601. Values are maximum unless a range is shown; ellipses (…) mean no requirement.
| Element | UNS S30601 melting analysis |
|---|---|
| Carbon (C) | ≤ 0.015 |
| Manganese (Mn) | 0.50 – 0.80 |
| Phosphorus (P) | ≤ 0.030 |
| Sulfur (S) | ≤ 0.013 |
| Silicon (Si) | 5.0 – 5.6 |
| Chromium (Cr) | 17.0 – 18.0 |
| Nickel (Ni) | 17.0 – 18.0 |
| Molybdenum (Mo) | ≤ 0.20 |
| Nitrogen (N) | ≤ 0.05 |
| Copper (Cu) | ≤ 0.35 |
Source: ASME SA-312/SA-312M ≡ ASTM A312/A312M Table 1, UNS S30601 (grade column “…”). Footnote C: nitrogen method by agreement.
Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.015 | 0.005 over | ≤ 0.020 |
| Manganese (Mn) | 0.50 – 0.80 | 0.03 under / over | 0.47 – 0.83 |
| Phosphorus (P) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Sulfur (S) | ≤ 0.013 | 0.005 over | ≤ 0.018 |
| Silicon (Si) | 5.0 – 5.6 | 0.15 under / over | 4.85 – 5.75 |
| Chromium (Cr) | 17.0 – 18.0 | 0.20 under / over | 16.80 – 18.20 |
| Nickel (Ni) | 17.0 – 18.0 | 0.15 under / over | 16.85 – 18.15 |
| Molybdenum (Mo) | ≤ 0.20 | No A480 row for ≤0.20% (rows start over 0.20) | Not established—by agreement |
| Nitrogen (N) | ≤ 0.05 | 0.01 over | ≤ 0.06 |
| Copper (Cu) | ≤ 0.35 | 0.03 over | ≤ 0.38 |
Molybdenum: A480 Table A1.1 gives Mo tolerances only for limits above 0.20%, so the ≤0.20% maximum has no published product tolerance. Acceptance of a Mo check analysis is by agreement.
Tolerance notes: silicon 5.0–5.6% is in the “over 3.00 to 6.00” row (0.15 each way). Nickel 17.0–18.0% is in the 10–20% row (0.15). The manganese range lies in the “to 1.00” row (0.03). Carbon ≤0.015% uses the “over 0.010 to 0.030” row (0.005). Sulfur ≤0.013% takes 0.005 over.
S30600 vs S30601 (Table 1):
| Element | S30600 | S30601 |
|---|---|---|
| C | ≤ 0.018 | ≤ 0.015 |
| Mn | ≤ 2.00 | 0.50 – 0.80 |
| P | ≤ 0.02 | ≤ 0.030 |
| S | ≤ 0.02 | ≤ 0.013 |
| Si | 3.7 – 4.3 | 5.0 – 5.6 |
| Cr | 17.0 – 18.5 | 17.0 – 18.0 |
| Ni | 14.0 – 15.5 | 17.0 – 18.0 |
| Mo | ≤ 0.20 | ≤ 0.20 |
| N | … | ≤ 0.05 |
| Cu | ≤ 0.50 | ≤ 0.35 |
Note that S30601 allows phosphorus up to 0.030% whereas S30600 is limited to 0.02%; conversely S30601 has the tighter sulfur limit. These are distinct alloys, not grades of one family that can be swapped freely.
Mechanical Properties of SA312 UNS S30601
| Property (SA-312 Table 4) | UNS S30601 |
|---|---|
| Tensile strength, min | 78 ksi [540 MPa] |
| Yield strength (0.2% offset), min | 37 ksi [255 MPa] |
| Elongation in 2 in. or 50 mm (or 4D), min | 35% longitudinal / 25% transverse |
| Hardness | No maximum listed in Table 4 |
S30601 shares the 78 ksi tensile floor of S30600 but has a 2 ksi higher yield minimum (37 vs 35 ksi), reflecting the extra silicon strengthening. Both are well above TP304L (70/25 ksi).
The elongation minimum is the same as for common austenitics, so properly annealed pipe must remain ductile. Flattening tests on 5% of each lot confirm that the pipe deforms without cracking—an important check for a high-silicon alloy, where improper anneal or contamination could reduce ductility.
For design, use allowable stresses for S30601 from the governing code where listed. In acid plants, pressures are usually low, and wall thickness is driven more by corrosion allowance, fabrication, and support requirements than by stress.
Forming: S30601 is harder to cold form than 304. Bend radii should be generous and trials made before production bending. Hot forming is not recommended outside the producer’s guidance.
Thermal expansion and supports: like other austenitic grades, S30601 expands more than carbon steel with temperature. In acid plant layouts, where S30601 lines connect to carbon steel or lined equipment, expansion loops or flexible supports may be needed. These are design matters outside SA-312 but worth noting when replacing older piping materials. Elevated-temperature properties and impact toughness are not part of SA-312 for this grade. Acid service temperatures are moderate in metallurgical terms, so those properties seldom govern.
Dimensions and Tolerances
S30601 pipe is sized to ASME B36.19 (Sch 5S, 10S, 40S, 80S) or special OD/wall by agreement. In practice, acid-plant piping in this alloy is often specified by OD and wall to the licensor’s line list.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
Source: SA-312 Table 3; outside diameter variations per A999/A999M.
- Lengths: NPS 1/8 to 8 up to 24 ft (15–24 ft range) unless agreed; larger welded pipe often supplied in plate-limited lengths
- Cut lengths: no more than 1/4 in. [6 mm] over, never under
- Jointers: not permitted unless specified
Welded pipe NPS 20 and larger carries a +17.5% / −12.5% wall tolerance. For acid service, many owners specify the minimum wall directly (S8) and add a corrosion allowance. Check that fittings and flanges in S30601 are available in the same wall and OD—fitting availability often limits the line design.
Large distributor headers in absorption towers may be fabricated from S30601 plate rolled and welded into pipe-like sections. Whether such parts fall under SA-312 or are treated as fabricated components to the plate specification depends on how they are made and certified; clarify this with the licensor and the inspector before ordering.
Spool fabrication is commonly done by the pipe producer or a specialist fabricator to control welding and pickling of this alloy.
Equivalent Grades
| Designation | Relationship to S30601 |
|---|---|
| ASME SA-312 / ASTM A312, UNS S30601 | Governing pipe grade (no TP name) |
| ASME SA-240 / A240 S30601 | Plate counterpart (separate specification) |
| UNS S30600 | Lower-silicon sister (3.7–4.3% Si); not interchangeable |
| EN / JIS | No one-to-one designation asserted; verify against regional standards if needed |
| Producer trade names | 5% Si austenitic stainless brands exist; order by UNS S30601 |
Do not confuse S30601 with S30615, a high-silicon heat-resisting grade with high carbon and aluminium. Related pages: ASME SA312 UNS S30600 Stainless Steel Pipe, ASME SA312 UNS S30615 Stainless Steel Pipe, ASME SA312 TP304L Stainless Steel Pipe, ASME SA312 TP316L Stainless Steel Pipe.
Heat Treatment and Delivery Condition
SA-312 Table 2 lists S30601 individually:
| Grade | Solution treatment temperature | Cooling |
|---|---|---|
| UNS S30601 | 2010–2140 °F [1100–1170 °C] | Water quench or rapid cooling (Table 2 note D) |
The ranged temperature is the same as for S30600. A higher solution temperature than the 1900 °F default is needed to take silicon-rich phases back into solution and develop a uniform austenitic structure. Below 2010 °F the anneal does not comply; above 2140 °F the risk of grain growth and incipient melting at segregated regions increases.
S30601 is not among the grades that ASME clause 6.2 requires to be reheated, so seamless pipe could in principle be quenched directly after hot forming at or above 2010 °F. In practice most S30601 pipe is welded and annealed as a separate operation.
- Delivered solution annealed within the Table 2 range and rapidly cooled
- Pickled, free of scale and exogenous iron
- Passivation on request
- Anneal temperature recorded on the MTC
Fabricated spools are normally not re-annealed after welding, but they should be pickled. Follow the alloy producer’s guidance if any post-weld heat treatment is considered.
Corrosion Resistance
S30601 is designed for hot concentrated sulfuric acid—typically the strong acid sections of sulfuric acid plants, including drying and absorption tower circuits, where acid concentrations are high and temperatures elevated. Producers and industry literature describe very low corrosion rates for 5% silicon austenitics in such conditions, outperforming conventional stainless steels and S30600 at the more severe end.
- Strong, hot sulfuric acid and oleum circuits: principal application
- Lower concentrations: as acid becomes more dilute and less oxidizing, the advantage of silicon decreases; other alloys may be better
- Nitric acid: high-silicon austenitics also perform well in strong nitric acid
- Chlorides and reducing acids: not intended for these services
- Erosion-corrosion: velocity limits from licensors and producers must be respected
Why ultra-low carbon matters here: in strong oxidizing acid, even minor chromium carbide networks at grain boundaries become attack paths. At ≤0.015% C, there is very little carbon available to form them, even in weld heat-affected zones.
Comparison with S30600: the extra silicon of S30601 is generally associated with lower corrosion rates at higher acid temperatures, but with greater fabrication difficulty and cost. S30600 may be preferred in somewhat less aggressive streams.
Operating discipline: high-silicon alloys depend on stable acid conditions. Upsets that dilute the acid (for example water ingress) or raise chloride levels can increase corrosion sharply. Plant operating procedures, not just the pipe material, determine service life. Many owners schedule periodic thickness measurements at elbows, tees, and pump discharges where turbulence is highest. All corrosion performance statements are general guidance; SA-312 contains no corrosion data. Validate with the acid plant licensor and, where possible, with coupon testing.
Applications of SA312 UNS S30601 Pipe
| Application | Role of S30601 | Note |
|---|---|---|
| Sulfuric acid plant strong acid circuits | Acid distributors, pump discharge, tower inlet and outlet lines | Typically replaces cast iron or brick-lined designs |
| Absorption and drying towers | Internal distributor pipes and headers | Velocity and temperature limits apply |
| Acid coolers | Connection piping to plate or shell-and-tube coolers | Some coolers are anodically protected |
| Oleum handling | Transfer and process lines | Confirm concentration range with producer |
| Strong nitric acid service | Process lines where high-Si austenitic is chosen | Low C critical |
| Metallurgical acid plants | Strong acid sections | Impurity levels influence life |
The use of S30601 often allows a simpler, lighter piping design than traditional cast iron or lined steel, with the added benefit of weldability. For less demanding acid streams, ASME SA312 UNS S30600 Stainless Steel Pipe may be sufficient.
Weldability
S30601 is weldable with GTAW, GMAW, and SMAW, but it is one of the more demanding austenitic alloys to weld because 5% silicon increases solidification-cracking tendency in a fully austenitic weld.
Filler metal and Table 6: S30601 is listed in SA-312 Table 6, but the AWS A5.9 class and filler UNS columns show “…”, meaning no filler classification is given. Filler choice is therefore by agreement and must be recorded on the WPS; for seam repairs, clause 15 requires the filler to be identified on the certificate. Fabricators normally use matching high-silicon consumables supplied by the alloy producers; standard 308L or 316L wires would produce welds without the base metal’s acid resistance.
- Low heat input: stringer beads, controlled interpass temperature
- Joint cleanliness: remove oxides, oils, and any sulfur- or phosphorus-bearing contamination
- Restraint: minimize joint restraint to reduce cracking
- Root quality: full penetration with argon purge; avoid backing rings that create crevices
- Post-weld pickling: essential to remove heat tint before acid exposure
Repair welding in service: if repairs are needed after the pipe has been in acid service, thorough cleaning and neutralization are essential before welding, because residual acid and sulfates in the metal surface can cause weld defects. Producers publish repair guidance for high-silicon alloys; follow it and record the repair in the plant’s maintenance file.
Procedures should be qualified on S30601 base metal to ASME Section IX, ideally with corrosion testing of weld coupons in representative acid. Make sure the welders on the job have qualified on S30601 itself rather than on 304L coupons.
Surface Finishes
Surface condition for UNS S30601 pipe should be stated on the purchase order rather than left to mill default. For stainless pipe, embedded free iron, residual scale, and chloride-bearing residues are where corrosion starts, so the finish is part of the material performance and not just appearance. The finishes we regularly quote for this grade are listed below.
- Annealed and pickled (AP) — solution annealed at 2010–2140 °F [1100–1170 °C], then descaled in acid pickle or an equivalent process to a matte grey finish; the standard choice for process pipe
- Blasted and pickled — common on heavy-wall seamless where blasting first makes scale removal more reliable
- Bright annealed (BA) — annealed in a protective atmosphere where mill capability exists for the size; the anneal temperature still has to meet the Table 2 practice for UNS S30601
- Mechanically polished — OD and/or ID polish to an agreed grit or Ra when ordered; polishing never replaces the solution anneal
- Bead-finished welded OD — weld bead rolled or ground flush as agreed on WLD and HCW product
Annealed and pickled is the finish to specify for acid service. The silica-rich scale formed at the high anneal temperature needs pickling conditions adjusted by the mill, and residual scale or heat tint will be the first place attacked, so inspect the bore of welded pipe on receipt and pickle and passivate site welds and heat-affected zones before acid exposure. Passivation after pickling or polishing can be added when the end-user specification calls for it, even though SA-312 itself does not require it. If the project bans chloride-bearing marking inks, say so on the order; otherwise the mill will apply its normal stencil practice and ship its default AP finish.
Inspection and Testing
The base acceptance package for SA-312 UNS S30601 pipe combines chemistry, tensile testing, heat-treatment evidence, and a pressure or electrical integrity test on every length. The items below make up the usual package; supplementary requirements and project corrosion tests only apply when they are written on the purchase order.
- Heat (melting) analysis — mandatory per heat against Table 1 for UNS S30601: Si 5.0–5.6%, Cr and Ni 17.0–18.0%, Mn 0.50–0.80%, C ≤0.015%, P ≤0.030%, S ≤0.013%, Mo ≤0.20%, N ≤0.05%, Cu ≤0.35%
- Product analysis — when ordered (Suppl. S1 or PO wording), using A480 Table A1.1 tolerances via A999 §6.3; A480 has no tolerance row for Mo at ≤0.20%, so Mo product acceptance is by agreement
- Tension test — 78 ksi [540 MPa] tensile, 37 ksi [255 MPa] yield, 35% L / 25% T elongation on a lot basis
- Flattening test — or the alternate bend test where the standard permits
- Hydrostatic or nondestructive electric test — every length; manufacturer’s option unless the order fixes the method
- Visual and dimensional check — against ordered NPS/schedule or OD × wall, with “UNS S30601” on every stencil
Mill test certificates: EN 10204 3.1 is the standard documentation from SHH STEEL supply. For S30601 the certificate should show silicon inside 5.0–5.6%, manganese inside 0.50–0.80%, carbon ≤0.015%, sulfur ≤0.013%, the Mo/N/Cu residuals as reported values, and the actual anneal temperature inside 2010–2140 °F. Flattening results matter more than usual here, because an improper anneal or contamination can reduce ductility in a 5% silicon alloy. EN 10204 3.2 or third-party witness by SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency is arranged when specified, and it should be booked before final testing rather than after the heat has been released. Dual ASME SA-312 / ASTM A312 certification is available when chemistry, heat treatment, mechanical tests, and marking satisfy both editions named on the order.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms chemistry on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S8 minimum wall | Wall interpreted as minimum rather than nominal |
| S9 weld decay | Compares weld and base-metal loss rates |
Receiving PMI is worthwhile because a mix-up with S30600 or 304L in a strong-acid circuit would be serious and the stencil shows only a UNS number. XRF will confirm silicon, chromium, and nickel approximately, but carbon at 0.015% needs OES or laboratory analysis. For critical service, corrosion-test weld coupons in representative acid before the welding procedure is released to production.
Packaging and Shipping
Export and domestic shipments of UNS S30601 pipe are packed for handling and for ocean or land transport. The packing we normally apply is summarized below, and anything beyond it can be agreed on the order.
- Seaworthy bundles — pipes strapped or cradled in bundles sized for container or break-bulk handling, with non-metallic separators where the finish needs protecting
- End caps — plastic or metal caps on plain or beveled ends to keep out damage and contamination in transit
- Marking — specification, grade (UNS S30601), heat number, size, manufacturing type (SML / WLD / HCW), test letters, and mill identity as SA-312 and the purchase order require
- Export protection — waterproof wrapping or desiccant as agreed for polished or bright-annealed finishes, with low-chloride inks on request
Keep S30601 bundles segregated from S30600 and 300-series stock at every handling point—the two high-silicon grades look identical and differ only in the UNS digits on the stencil. Desiccant inside sealed wrap and plugged ends are common requirements for sea shipments into acid plants; state them on the PO so the mill packs accordingly. Keep interiors dry and capped so chloride-bearing moisture cannot stain or pit the surface before installation. Shipping documents normally include the packing list, invoice, bill of lading or air waybill, and the 3.1 or 3.2 MTC with full Table 1 chemistry, plus origin and customs papers to suit the agreed Incoterms.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless plate and pipe, and for ASME SA312 UNS S30601 / S30601 we quote against the edition you name rather than a generic catalogue sheet. S30601 is a low-volume, high-consequence product: the usual failures are a heat certified to the S30600 row by mistake, a missing anneal temperature, or a procurement team that assumes 316L filler is fine. We source from mills with genuine 5% silicon experience and review the certificate against Table 1, Table 2, and Table 4 before release. Heat identity stays unbroken from the melt to the finished length, so receiving inspection can clear each heat against Table 1 and Table 4 without chasing paperwork after the pipe has arrived.
We also tell buyers plainly where SA-312 leaves decisions open. Table 6 lists S30601 but names no filler, and A480 gives no product tolerance for Mo at ≤0.20%, so both are written into the order by agreement. Where the acid conditions are less severe, we will point out that S30600 may do the job with easier fabrication, and where the stream is dilute or chloride-bearing we will say the high-silicon family is the wrong tool.
- Specification fidelity — certified as UNS S30601 with Si, Mn band, C, S, and Mo/N/Cu residuals reported, plus the actual 2010–2140 °F anneal temperature on the MTC
- Mill resources — SML, WLD, and HCW from qualified stainless pipe mills with heat traceability; cutting and beveling on confirmed orders
- Documentation — EN 10204 3.1 MTCs as standard with full Table 1 chemistry; 3.2 or third-party inspection on request
- Dual marking — ASME SA-312 and ASTM A312 when the heat and tests meet both editions you name
- Related grades — UNS S30600, TP304L, and TP316L when a project buys a matched package
- Export packing — seaworthy bundles, end protectors, and durable grade, heat, size, and type marking
Quotations follow your purchase-order language for edition year, manufacturing type, size, wall, finish, and any supplementary tests you name (S1, S5, S7, S8, S9). If the same project also needs plate or fittings, ask for coordinated heats so the chemistry lines up across product forms. Grade hub: ASME SA 312/SA 312M.
Supply Capability
SHH STEEL can supply ASME SA312 UNS S30601 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.
| Item | SHH STEEL capability for UNS S30601 |
|---|---|
| Standard | ASME SA-312/SA-312M and/or ASTM A312/A312M (edition per PO; grade marked UNS S30601, no TP name) |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD/wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | SRL, DRL, or cut-to-length |
| Finish | Annealed and pickled; blasted and pickled; bright annealed or polished by agreement |
| Testing | Hydrostatic or NDE per length; S1 product analysis, S5 radiography, PMI, and weld-coupon acid tests when ordered |
| Documents | EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
S30601 is made to order rather than stocked, and the producing mills set minimum quantities that are higher than for commodity grades. Bring the line list, walls, quantities, and a short description of the acid conditions to the first enquiry so feasibility, plate availability, and lead time can be confirmed before the project schedule is fixed. Enquiries should state the SA-312 edition, UNS S30601 (no TP name), SML/WLD/HCW, NPS or OD × wall (and whether wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements, so mill slots line up with your need date. Cut lengths, beveling, and packing-list marking are available on confirmed orders, and grouping project sizes onto one heat keeps the chemistry consistent while helping meet mill minimums without over-ordering.
FAQ
-
Does UNS S30601 have a TP grade name in SA-312?
- No. Table 1 shows an ellipsis in the grade column for S30601, so there is no TP designation. Order and mark it as “ASME SA-312 UNS S30601” or ASTM A312 UNS S30601 with the edition year, and do not accept certificates that describe it only by a producer trade name or as “5% silicon stainless”.
-
What is the silicon content of UNS S30601?
- Table 1 requires silicon of 5.0–5.6%, the highest silicon range in SA-312. Product analysis per A480 widens that to 4.85–5.75% on finished pipe. The silicon is what builds the silica-rich passive film in hot strong sulfuric acid, so it is the first number to check on the certificate, ahead of carbon and nickel.
-
What Table 1 chemistry defines UNS S30601?
- Table 1 sets C ≤0.015%, Mn 0.50–0.80%, P ≤0.030%, S ≤0.013%, Si 5.0–5.6%, Cr 17.0–18.0%, Ni 17.0–18.0%, Mo ≤0.20%, N ≤0.05%, and Cu ≤0.35%. These are melting-analysis limits; order product analysis (S1) on the purchase order if the finished pipe must be checked, and note that the nitrogen method is by agreement.
-
What are the Table 4 mechanical requirements for S30601?
- Table 4 requires 78 ksi [540 MPa] minimum tensile and 37 ksi [255 MPa] minimum yield, with 35% longitudinal and 25% transverse elongation and no hardness limit. That is the same tensile floor as S30600 but 2 ksi more yield, reflecting the extra silicon. Acid-plant pressures are usually low, so corrosion allowance tends to govern the wall.
-
What heat treatment does Table 2 require for S30601?
- Table 2 lists S30601 at 2010–2140 °F [1100–1170 °C], followed by water quench or other rapid cooling. The high, ranged temperature is needed to take silicon-rich phases back into solution and give a uniform austenitic structure. Ask for the actual anneal temperature on the MTC; a statement of “solution annealed” alone does not prove the range was met.
-
Which filler metal does Table 6 list for S30601?
- S30601 appears in Table 6, but the AWS A5.9 class and filler UNS columns show only ellipses, so no filler is specified. Selection is by agreement and must be frozen on the WPS. Fabricators normally use matching high-silicon consumables from the alloy producers; standard 308L or 316L wire would give welds without the base metal’s acid resistance.
-
How does UNS S30601 compare with UNS S30600?
- S30601 has more silicon (5.0–5.6% versus 3.7–4.3%), more nickel (17.0–18.0% versus 14.0–15.5%), lower carbon (≤0.015% versus ≤0.018%), a controlled 0.50–0.80% manganese band, tighter sulfur, and a 37 ksi rather than 35 ksi yield floor. It targets hotter, stronger acid, but it is harder to fabricate and costs more.
-
Can UNS S30601 replace S30600 in an existing acid plant?
- Only after engineering review. The chemistries, yield minima, and welding behaviour differ, and the substitution should be checked against the actual acid concentration and temperature, the filler practice, and any licensor velocity limits. Upgrading to S30601 can make sense in the hottest circuits, but it is a material change that needs a documented decision, not a like-for-like swap.
-
Is UNS S30601 easy to weld?
- It is one of the more demanding austenitic alloys to weld, because 5% silicon raises solidification-cracking risk in a fully austenitic weld. Use low heat input with stringer beads, clean joints, minimum restraint, an argon-purged full-penetration root without backing rings, and pickling afterwards. Qualify procedures to ASME Section IX on S30601 base metal before production.
-
Is there a product-analysis tolerance for molybdenum in S30601?
- A480 Table A1.1 does not give one at this level, because its molybdenum rows begin at limits over 0.20%. With a Table 1 maximum of exactly 0.20%, product-analysis acceptance for Mo is by agreement. We report the heat value and do not invent a tolerance; if the inspector needs a number, it should be written on the purchase order.
-
Is UNS S30601 available as seamless pipe?
- SA-312 permits seamless, welded, and heavily cold-worked S30601, and every route must meet the same chemistry and the 2010–2140 °F anneal. Seamless production is uncommon because the high silicon makes hot working difficult, so most S30601 pipe is welded from plate with radiographed seams. Confirm the route and size range with the mill at enquiry stage.
-
Does S30601 pipe need special pickling after welding?
- Yes, cleanliness matters more than usual. Mills adjust pickling for the silica-rich scale formed at the high anneal temperature, and after site welding the welds and heat-affected zones should be pickled and passivated to remove heat tint, which is attacked first in strong acid. Inspect the bore of welded spools before they go into service.
Conclusion
ASME SA312 UNS S30601 is the TP-less, highest-silicon austenitic pipe grade in SA-312: Si 5.0–5.6%, Cr and Ni 17.0–18.0%, C ≤0.015%, Mn 0.50–0.80%, with 78 ksi [540 MPa] tensile and 37 ksi [255 MPa] yield minima after a 2010–2140 °F [1100–1170 °C] solution anneal. It is built for hot, strong sulfuric acid; it is not interchangeable with UNS S30600 or UNS S30615, and because Table 6 names no filler and A480 gives no Mo tolerance at this level, both belong on the order by agreement. For sizes, lead times, mill certificates, or dual SA-312/A312 supply, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category.