ASTM A312 TP201LN Stainless Steel Pipe | ASTM A312 Stainless Steel - SHH STEEL

ASTM A312 TP201LN Stainless Steel Pipe

ASTM A312 TP201LN (UNS S20153) stainless steel pipe under A312/A312M: seamless, welded and heavily cold-worked; ASME B36.19 schedules; solution annealed. Low-carbon Mn–N chemistry per Table 1; tensile 95 ksi min, yield 45 ksi min. SHH STEEL supplies with EN 10204 3.1 MTCs.
Grade
TP201LN / UNS S20153
Standard
ASTM A312 / A312M
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASTM A312 TP201LN Stainless Steel Pipe

ASTM A312 / A312M specifies seamless, welded, and heavily cold-worked austenitic stainless steel pipe for high-temperature and general corrosive service. Grade TP201LN is the low-carbon, nitrogen-bearing lean-nickel austenitic listed as UNS S20153 — not to be confused with TP201 / UNS S20100. Table 1 sets carbon ≤0.03%, manganese 6.4–7.5%, chromium 16.0–17.5%, nickel 4.0–5.0%, nitrogen 0.10–0.25%, and copper ≤1.00%, with sulfur held to ≤0.015%. That Mn–N balance is what delivers the 95 ksi / 45 ksi Table 4 tensile floor while keeping nickel well below the 304 family.

SHH STEEL can supply ASTM A312 TP201LN stainless steel pipe as SML, WLD, and HCW product in ASME B36.19 schedules and special OD/wall by agreement, with EN 10204 3.1 certificates that report the full Table 1 chemistry — including nitrogen and copper — plus the 95/45 ksi tensile results and the 1900 °F solution anneal. Dual A312 / SA-312 marking is added only when the purchase order requests that separate ASME standard. See the wider grade list on the A312/A312M

Buyers and mills still shorten the name to 201LN or S20153; bare “201” on a PO is dangerous because it may pull TP201 / S20100 instead. Sister ASTM A312 pages commonly compared on the same enquiry include A312 TP201 (standard 201), A312 UNS S20400 in the lean-nickel neighborhood, A312 TP304L / A312 TP304LN when a conventional 18-8 low-carbon route is preferred, and A312 TP316L when chlorides dominate. For ASME Code Book wording on the same grade, open the separate SA312 TP201LN page — written to SA-312 as its own standard.

Manufacturing Types (SML / WLD / HCW)

ASTM A312 allows TP201LN as seamless, welded, and heavily cold-worked pipe. The manufacturing type is mandatory marking content. Seamless suits pressure or owner-mandated no-seam service; welded is common for utility and structural lengths where the lean-nickel chemistry is doing the cost work; HCW is welded pipe given defined cold reduction and certified as its own type.

Because nitrogen and manganese strengthen the alloy, cold-forming and weld shrinkage behave differently from soft 304L — fabricators should qualify procedures on actual 201LN, not assume a 304L WPS transfers. SHH STEEL states SML, WLD, or HCW on the stencil and certificate. Wall is nominal unless S8 is ordered; OD follows A999/A999M.

Never accept a shipment stenciled TP201 when the PO said TP201LN: the UNS numbers, carbon, sulfur, nitrogen, and tensile floors differ, and receiving inspection should catch that before fabrication starts.

Chemical Composition of A312 TP201LN

TP201LN chemistry under ASTM A312 is defined by Table 1 melting analysis on every heat. Product analysis applies only when S1 (or equivalent) is ordered, using A480/A480M Table A1.1 tolerances. Nitrogen analysis method is by agreement per the Table 1 footnote language in the ordered edition — we report N on the MTC inside the 0.10–0.25% band rather than leaving it blank.

The tables below reproduce the Table 1 melt limits for TP201LN / UNS S20153 and the product-analysis limits after A480 tolerances. Ellipsis (…) means no requirement (molybdenum in this grade).

Melting analysis (heat / ladle analysis) — Table 1

Element TP201LN (UNS S20153) melting analysis
Carbon (C) ≤ 0.03
Manganese (Mn) 6.4 – 7.5
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.015
Silicon (Si) ≤ 0.75
Chromium (Cr) 16.0 – 17.5
Nickel (Ni) 4.0 – 5.0
Nitrogen (N) 0.10 – 0.25
Copper (Cu) ≤ 1.00
Molybdenum (Mo) … (no requirement)

Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.03 0.005 over ≤ 0.035
Manganese (Mn) 6.4 – 7.5 0.06 under / over 6.34 – 7.56
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.015 0.005 over ≤ 0.020
Silicon (Si) ≤ 0.75 0.05 over ≤ 0.80
Chromium (Cr) 16.0 – 17.5 0.20 under / over 15.80 – 17.70
Nickel (Ni) 4.0 – 5.0 0.07 under / over 3.93 – 5.07
Nitrogen (N) 0.10 – 0.25 0.01 under / 0.02 over 0.09 – 0.27
Copper (Cu) ≤ 1.00 0.05 over ≤ 1.05

Compared with A312 TP201, TP201LN tightens carbon to ≤0.03%, holds sulfur to ≤0.015%, and sets a nitrogen range that supports the higher Table 4 strength. Compared with A312 TP304L, nickel is roughly half and manganese is several times higher — different scrap economics and different welding behavior. Product analysis may read C ≤0.035%, Mn 6.34–7.56%, P ≤0.055%, S ≤0.020%, Si ≤0.80%, Cr 15.80–17.70%, Ni 3.93–5.07%, N 0.09–0.27%, Cu ≤1.05%.

SHH STEEL will not sell “201LN” against an S20100 heat. If the PO says TP201LN, the certificate must show S20153 chemistry including nitrogen.

Mechanical Properties of A312 TP201LN

Table 4 sets TP201LN at 95 ksi [655 MPa] tensile and 45 ksi [310 MPa] yield minimum, with elongation 35% longitudinal / 25% transverse minimum. That is a distinctly higher strength floor than TP304 (75/30) or TP304L (70/25), and it is why structural and OEM buyers sometimes prefer 201LN when lean nickel and higher yield both matter. Table 4 does not list a hardness maximum for TP201LN; catalogue HB/HRB figures are not ASTM acceptance values unless added on the PO.

Property TP201LN requirement (Table 4)
Tensile strength, min 95 ksi [655 MPa]
Yield strength (0.2% offset), min 45 ksi [310 MPa]
Elongation in 2 in. or 50 mm (or 4D) 35% longitudinal / 25% transverse, min

Designers must not assume TP201 and TP201LN share tensile rows — check Table 4 for each grade. Flattening or bend tests and hydro or NDE of each length complete the standard package. When a drawing cites 95/45 ksi, the MTC must show those numbers under ASTM A312 Grade TP201LN, not a substituted lean grade with a lower floor.

Dimensions and Tolerances

ASTM A312 TP201LN pipe uses ASME B36.19 schedules for common NPS × schedule combinations, with special OD/wall by agreement. OD variations follow A999/A999M; wall variations follow A312 Table 3. State nominal or minimum wall (S8) on the purchase order.

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%

Source: ASTM A312 Table 3; OD per A999/A999M. Higher yield sometimes lets designers thin a schedule versus 304 on structural pipe — verify that choice against buckling, corrosion allowance, and welding distortion, not only against tensile floor. Representative stock/enquiry sizes appear under Supply Capability without invented warehouse tonnages.

Equivalent Grades

There is no single mandatory EN or JIS one-to-one equivalent that we assert for TP201LN on an ASTM A312 certificate. Regional Mn–N low-carbon names vary; order non-ASTM product under the actual EN or JIS pipe specification when that is the contract basis.

Designation Notes
ASTM A312 / A312M Grade TP201LN Governing ASTM pipe product standard for this article
UNS S20153 Unified number listed in Table 1 — distinct from S20100 (TP201)
ASME SA-312 TP201LN Separate ASME Code Book adoption — dual-mark only when the PO asks
EN / JIS approximations Regional Mn–N low-carbon designations vary; confirm the applicable EN or JIS product specification when ordering non-ASTM product — do not mark EN/JIS alone on an A312 MTC

Related plate in the 201 family is often sold as UNS S20100 — that is not S20153. Keep pipe and plate UNS numbers straight on mixed BOMs. ASME SA-312 TP201LN is the separate Code adoption; dual-mark on request only. For conventional low-carbon 18-8 compare A312 TP304L; for nitrogen-strengthened 304 chemistry compare A312 TP304LN.

Heat Treatment and Delivery Condition

TP201LN is not individually listed at a special temperature in Table 2, so it follows the default solution-anneal minimum of 1900 °F [1040 °C] with water quench or rapid cooling. The anneal puts carbon and nitrogen into solution and restores ductility after cold work or welding at the mill. SHH STEEL delivers solution annealed and pickled pipe as standard, bright annealed by agreement, with the anneal temperature on the EN 10204 3.1 certificate.

Skipping mill solution treatment leaves nitrogen-strengthened lean austenitics vulnerable to inconsistent mechanical results even when ladle chemistry looked right. Supplementary S7 intergranular testing, when ordered, is reported with the heat-treatment record.

Corrosion Resistance

TP201LN offers useful resistance in mild aqueous and atmospheric services where owners accept lean-nickel austenitics. It is not a molybdenum grade: chloride pitting and crevice performance should not be assumed equal to A312 TP316L or even casually equal to A312 TP304L without testing or owner approval. The low carbon helps as-welded intergranular resistance relative to higher-carbon 201 chemistries, which is part of why the LN designation exists.

ASTM A312 publishes no corrosion-rate table for TP201LN. Selection remains engineering judgment. SHH STEEL will not rank 201LN as interchangeable with 304L in every fluid — chemistry and industry experience differ, and the certificates stay on S20153.

Applications of A312 TP201LN Pipe

TP201LN is ordered when lean nickel, low carbon, and a 95/45 ksi strength floor fit the commercial and structural brief better than commodity 304L. Utility piping, architectural/structural pipe, transportation OEM kits, and mild process lines are typical under ASTM A312.

Application area Typical use of TP201LN pipe Selection note
Utility and process piping Water, air, mild chemical transfer lines ordered to A312 Confirm fluid compatibility with 201LN chemistry
Structural / architectural Handrail, support, and decorative pipe ordered as A312 product Higher min yield (45 ksi) vs TP201/TP304 can help section design
Transportation / OEM Frames and piping kits converting to A312 documentation Dual A312/SA-312 marking often requested; confirm S20153 not S20100
General corrosive service Mild to moderate environments without heavy chlorides Prefer TP316/TP316L or higher alloys if chlorides dominate
High-strength lean-nickel service Where 95/45 ksi Table 4 floors are specified with low carbon Do not substitute TP201 (S20100) certificates

If the specification literally requires TP304L chemistry, do not substitute 201LN without a formal engineering change. If chlorides dominate, open A312 TP316L. If standard 201 without the LN controls is enough, compare A312 TP201 carefully — different UNS, different tensile expectations.

Weldability

ASTM A312 Table 6 shows an ellipsis (“…”) for TP201LN filler classification — filler is by agreement, the same Table 6 status TP201 carries. Fabricators typically qualify a matching or near-matching Mn–N austenitic filler, or another filler approved in the WPS, rather than assuming ER308L from a 304L procedure will be accepted by the owner.

Higher strength and nitrogen change distortion and hot-cracking margins versus soft 304L; procedure qualification on production-representative material is the safe path. SHH STEEL notes “filler by agreement” against Table 6 on request documents and does not invent an AWS class the standard leaves open.

Surface Finishes

Standard finish is solution annealed and pickled. Blasted-and-pickled and bright-annealed options are available by agreement — bright anneal is often requested on architectural 201LN. Polished finishes for visible handrail or decorative pipe are commercial extras with their own Ra language; they are not implied by the ASTM grade stamp.

Stencil content still prioritizes ASTM A312, TP201LN, manufacturing type, and heat number so S20153 is never mistaken for S20100 after polish or paint at site.

Inspection and Testing

Base testing covers Table 1 chemistry including nitrogen and copper, Table 4 tension at 95/45 ksi, flattening or bend tests, and hydro or NDE of each length. Marking must identify TP201LN distinctly. Supplementary Requirements commonly added are listed below.

Option Purpose
S1 product analysis Confirms chemistry on finished pipe
S5 radiography Weld integrity on WLD pipe
S7 intergranular corrosion A262 Practice E after sensitizing treatment
S8 minimum wall Wall interpreted as minimum rather than nominal
S9 weld decay Compares weld and base-metal loss rates

EN 10204 3.1 from SHH STEEL shows the full lean-nickel chemistry and tensile pair. Third-party inspection or 3.2 is available when named. Receiving teams should verify UNS S20153 on the certificate before releasing material into a 201LN isometric.

Packaging and Shipping

Lengths are bundled, end-protected, and tagged with ASTM A312 TP201LN, size, heat number, and PO reference. Export packing follows agreed Incoterms. Architectural or polished lots may ship cased; structural bundles may ship bare or wrapped.

Because TP201 and TP201LN are easy to mix in a warehouse, we segregate tags and bundle marks by UNS on mixed lean-nickel shipments when both grades appear on one order.

Why Choose SHH STEEL

SHH STEEL documents TP201LN as UNS S20153 under ASTM A312 with nitrogen, copper, low carbon, and 95/45 ksi on the certificate — not as a relabeled 201 heat. Manufacturing type is stenciled; dual SA-312 marking is optional and explicit. That discipline prevents the most common lean-nickel receiving failure: S20100 paperwork against an S20153 callout.

We also keep sister-grade advice straight. Need conventional 18-8 low carbon? Open A312 TP304L. Need nitrogen-strengthened 304? Open A312 TP304LN. Need molybdenum? Open A312 TP316L. Need standard 201? Open A312 TP201. The A312/A312M lists them as separate ASTM products rather than one “201/304 alternative” blur.

Quotations say what is near-term versus mill-produced. Filler remains by agreement per Table 6. The goal is pipe that matches the LN callout the engineer actually wrote.

Supply Capability

SHH STEEL can supply ASTM A312 TP201LN stainless steel pipe to the edition and manufacturing type on your enquiry. Capability summary first; Stock / Available sizes second.

Item SHH STEEL capability for TP201LN
Standard ASTM A312 / A312M (dual SA-312 marking on request) TP201LN / UNS S20153
Manufacturing types SML, WLD, HCW
Size NPS 1/8 and up per ASME B36.19; special OD/wall by agreement
Schedules 5S, 10S, 40S, 80S and non-standard walls
Length SRL, DRL, or cut-to-length
Finish Annealed and pickled; blasted and pickled; bright annealed or polished by agreement
Testing Tension (95/45 ksi), flattening/bend, hydro or NDE per length; full Table 1 chemistry with N 0.10–0.25% and Cu on MTC; 1900 °F anneal stated; S1/S5/S7/S8/S9 on order
Documents EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Stock / Available sizes

SHH STEEL quotes TP201LN pipe against a practical stock-and-mill enquiry range rather than a frozen warehouse SKU list. The sizes below are the combinations buyers most often request under ASME B36.19; availability of any single NPS × schedule on a given week depends on mill rolling and our inbound schedule, so treat the table as a supply map for enquiry — not a guarantee that every line sits on the floor with a published tonnage.

Item Typical stock / enquiry range for TP201LN
NPS 1/2, 3/4, 1, 1-1/4, 1-1/2, 2, 2-1/2, 3, 4, 5, 6, 8, 10, 12, 14, 16, 18, 20, 24 (intermediates and larger on enquiry)
Schedules Sch 5S, 10S, 40S, 80S per ASME B36.19; other walls by agreement
Common OD × wall examples 21.3 × 2.77 mm (NPS 1/2 Sch 40S); 33.4 × 3.38 mm (NPS 1 Sch 40S); 60.3 × 3.91 mm (NPS 2 Sch 40S); 88.9 × 5.49 mm (NPS 3 Sch 40S); 114.3 × 6.02 mm (NPS 4 Sch 40S); 168.3 × 7.11 mm (NPS 6 Sch 40S); 219.1 × 8.18 mm (NPS 8 Sch 40S) — illustrative B36.19 sizes
Length SRL, DRL, or cut-to-length on enquiry
Special Non-standard OD/wall, heavy wall, HCW, and polished finishes — confirm on enquiry before the heat is reserved

When you send an enquiry, list NPS × schedule (or OD × wall), manufacturing type (SML / WLD / HCW), quantity or cut list, required marking (A312 alone or dual A312/SA-312), and any Supplementary Requirements. We reply with what we can ship from near-term stock versus what needs a mill run, without inventing fake warehouse codes or tonnage claims.

List NPS × schedule or OD × wall, SML/WLD/HCW, quantity, marking (A312 or dual A312/SA-312), any S1/S5/S7/S8/S9 extras, and destination. We confirm S20153 chemistry with nitrogen and the 95/45 ksi tensile floor before the heat is reserved.

FAQ

Is ASTM A312 the same as ASME SA-312 for TP201LN?
No. ASTM A312 / A312M is the ASTM product specification; ASME SA-312 / SA-312M is the separate ASME Code Book adoption. Chemistry and tensile floors for TP201LN align closely, but the standards are independent. Dual-mark A312/SA-312 only when the purchase order requests both names on the stencil and MTC.
What is the UNS number for TP201LN?
TP201LN is UNS S20153. That number is distinct from TP201 / UNS S20100. Purchase orders, stencils, and MTCs should show S20153 when TP201LN is ordered. Plate sold as S20100 in the 201 family is not automatic pipe equivalence — confirm the pipe UNS on every lean-nickel line item.
Seamless vs welded TP201LN — which should I order?
Order seamless (SML) when the specification prefers a wall without a weld seam. Order welded (WLD) for everyday utility and structural lengths where A312 welded product is accepted. HCW is a third manufacturing type with defined cold work. Name SML, WLD, or HCW on the PO; chemistry alone does not select the type.
Hydrostatic test or NDE — which will my TP201LN pipe get?
ASTM A312 allows hydrostatic testing or nondestructive electric testing of each length. State a mandatory preference if the end user requires one route; otherwise the mill applies the permitted option for the manufacturing type. Supplementary radiography (S5) is separate from that hydro/NDE choice.
Does A312 Table 4 set a hardness limit for TP201LN?
No. Table 4 lists 95 ksi tensile, 45 ksi yield, and elongation minima only. No hardness maximum is published for TP201LN in that table. If a project needs a maximum HB or HRB, add it to the purchase order with an agreed test method rather than relying on catalogue hardness claims.
What filler metal should I use to weld TP201LN pipe?
Table 6 shows an ellipsis for TP201LN — filler is by agreement, not a fixed AWS class in the product standard. Qualify a matching Mn–N austenitic filler or another owner-approved filler in the WPS. Do not assume ER308L from a 304L procedure is automatically accepted for 201LN without procedure review.
What wall-thickness tolerance applies to TP201LN pipe?
Wall variations follow ASTM A312 Table 3 for all grades, including TP201LN: 12.5% under-tolerance across the listed NPS bands, with over-tolerance depending on NPS and t/D. OD variations follow A999/A999M. Invoke S8 if wall must be interpreted as minimum rather than nominal.
Which sister grades do buyers compare with TP201LN?
Common ASTM A312 comparisons are TP201 (S20100), UNS S20400 lean-nickel neighbors, TP304L / TP304LN for conventional or nitrogen-bearing 18-8 low-carbon routes, and TP316L when chlorides require molybdenum. Each grade keeps its own Table 1 chemistry and Table 4 tensile row — compare on the hub rather than treating them as synonyms.
TP201LN vs TP201 — what is the difference?
TP201LN / S20153 uses lower carbon (≤0.03%), tighter sulfur (≤0.015%), a nitrogen range of 0.10–0.25%, copper ≤1.00%, and a 95/45 ksi tensile floor under Table 4. TP201 / S20100 is a different UNS with its own Table 1 and tensile requirements. They are sister lean-nickel grades, not interchangeable stamps on an ASTM A312 MTC.
TP201LN vs TP304L — which should I order?
Order TP304L when the specification needs conventional 18-8 low-carbon chemistry (≈8–13% Ni) and a 70/25 ksi floor. Order TP201LN when lean nickel, Mn–N strengthening, and a 95/45 ksi floor are specified or commercially preferred for mild service. They weld and corrode differently; do not substitute without engineering approval and a PO change.
What heat treatment does ASTM A312 require for TP201LN?
TP201LN follows the Table 2 default solution anneal at 1900 °F [1040 °C] minimum with rapid cooling, because it is not individually listed at another temperature. The anneal should be stated on the mill test certificate. Bright annealing is a commercial atmosphere option, not a waiver of solution treatment.
What product-analysis limits apply to TP201LN?
Product analysis applies only when S1 or equivalent wording is ordered. Limits are Table 1 values plus A480/A480M Table A1.1 tolerances: for example C ≤0.035%, Mn 6.34–7.56%, S ≤0.020%, Cr 15.80–17.70%, Ni 3.93–5.07%, N 0.09–0.27%, Cu ≤1.05%. SHH STEEL quotes those product windows only — not tighter invented catalogue chemistries.

Conclusion

ASTM A312 TP201LN / UNS S20153 is the low-carbon, nitrogen-bearing lean-nickel pipe grade for buyers who need a 95/45 ksi strength floor without 304-level nickel. SHH STEEL supplies SML, WLD, and HCW product to B36.19 and special OD/wall, solution annealed, tested, and documented on EN 10204 3.1 certificates that show nitrogen and copper — with dual SA-312 marking only when that separate ASME standard is named. Start from the ASTM A312/A312M product hub, confirm S20153 rather than S20100, and send the size list so stock and mill routes can match the ASTM callout.

Contact: admin@steelspecs.com

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X