ASTM A312 UNS S30600 Stainless Steel Pipe
What is ASTM A312 UNS S30600 Stainless Steel Pipe
A312/A312M is the ASTM product specification for seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. It stands on its own as an ASTM standard, and this page is written against it. UNS S30600 is one of the less common rows in its Table 1, and that is exactly why buyers ask us to spell out what the specification actually fixes for this alloy and what is left to agreement between purchaser and mill.
UNS S30600 is the high-silicon austenitic alloy of A312, listed by UNS number with no TP name. Its 3.7–4.3% silicon, combined with 17.0–18.5% chromium, 14.0–15.5% nickel, and an ultra-low 0.018% carbon ceiling, is designed for hot concentrated sulfuric acid and other strongly oxidizing media where ordinary 304L and 316L corrode rapidly. Its Table 4 floor of 78 ksi tensile and 35 ksi yield is modest; buyers choose it for corrosion behaviour, not strength.
SHH STEEL can supply ASTM A312 UNS S30600 pipe as seamless (SML), welded (WLD), or heavily cold-worked (HCW) product, in ASME B36.19 stainless schedules or special OD and wall by agreement, with EN 10204 3.1 mill test certificates that report the full Table 1 heat analysis, the Table 4 tension results, and the heat-treatment record. Where a purchase order also asks for ASME SA-312 marking, dual marking can be offered on heats that qualify under both documents, but the ASTM grade remains the one this page describes.
The order should read ASTM A312 UNS S30600. The alloy is widely known by producer trade names, and European enquiries may quote EN 1.4361, but the contract chemistry is the Table 1 row. It is easily confused with its higher-silicon sister S30601, and the two are not interchangeable without review because their silicon, nickel, and service windows differ.
If UNS S30600 turns out not to be the right fit, the closest sister pages in the same ASTM series are A312 UNS S30601, A312 UNS S31002, A312 UNS S30615, A312 TP304L, and A312 TP316L. All A312 grades are collected on the A312/A312M hub, so a short list can be compared against one standard before the enquiry goes out.
Manufacturing Types (SML / WLD / HCW)
ASTM A312 allows three manufacturing routes for UNS S30600 pipe, and the route is a purchase-order decision rather than a property of the grade. Whichever route is chosen, the heat must still meet the same Table 1 limits (C ≤0.018%, Mn ≤2.00%, P ≤0.02%, S ≤0.02%, Si 3.7–4.3%, Cr 17.0–18.5%, Ni 14.0–15.5%, Mo ≤0.20%, and Cu ≤0.50%), the same Table 4 tension floor, and the same 2010–2140 °F [1100–1170 °C] solution anneal (Table 2, individually listed) with rapid cooling heat-treatment requirement before any length is released.
- Seamless (SML) pierced and hot or cold finished, chosen for heavy wall, high pressure, or owner specifications that exclude a weld seam
- Welded (WLD) formed from flat-rolled product and welded without filler or with filler where the edition allows, economical in thinner walls and larger diameters
- Heavily cold-worked (HCW) welded pipe given at least 35% cold reduction of the weld and base metal before the final anneal, which refines the weld structure toward seamless behaviour
S30600 is a specialty acid-plant alloy, so pipe is commonly seamless in small and medium sizes and welded in larger diameters for acid circulation lines, with the route and any seam filler agreed early. Tell us which route your design code or client specification accepts, because a quotation that leaves the route open forces the mill to choose and can create disputes at receiving inspection.
Chemical Composition of ASTM A312 UNS S30600
The melting analysis in Table 1 is what the heat must meet when it is cast, and it is the first table a reviewer should compare against the mill certificate. For UNS S30600 the defining limits are C ≤0.018%, Mn ≤2.00%, P ≤0.02%, S ≤0.02%, Si 3.7–4.3%, Cr 17.0–18.5%, Ni 14.0–15.5%, Mo ≤0.20%, and Cu ≤0.50%. The table below reproduces the Table 1 row as published, with elements carrying no requirement shown as such rather than filled with invented values.
| Element | UNS S30600 melting analysis |
|---|---|
| Carbon (C) | ≤ 0.018 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.02 |
| Sulfur (S) | ≤ 0.02 |
| Silicon (Si) | 3.7 – 4.3 |
| Chromium (Cr) | 17.0 – 18.5 |
| Nickel (Ni) | 14.0 – 15.5 |
| Molybdenum (Mo) | ≤ 0.20 |
| Copper (Cu) | ≤ 0.50 |
| Nitrogen (N) | … (no requirement) |
Silicon at 3.7–4.3% is the defining line and the first to check; it is what forms the protective silica-rich film in hot strong sulfuric acid. Carbon at 0.018% maximum, phosphorus and sulfur at 0.02% maximum each, and copper capped at 0.50% are all tighter than common grades, so a certificate built from a 304L template will usually miss some of them.
Product analysis is a separate check made on the finished pipe, and ASTM A312 refers it to the permitted variations in ASTM A480 Table A1.1. The second table adds those tolerances to the melt limits so you can see the band that a check analysis on the pipe is allowed to fall within when Supplementary Requirement S1 or an owner check is ordered.
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.018 | 0.005 over | ≤ 0.023 |
| Manganese (Mn) | ≤ 2.00 | 0.04 over | ≤ 2.04 |
| Phosphorus (P) | ≤ 0.02 | 0.005 over | ≤ 0.025 |
| Sulfur (S) | ≤ 0.02 | 0.005 over | ≤ 0.025 |
| Silicon (Si) | 3.7 – 4.3 | 0.15 under / over | 3.55 – 4.45 |
| Chromium (Cr) | 17.0 – 18.5 | 0.20 under / over | 16.80 – 18.70 |
| Nickel (Ni) | 14.0 – 15.5 | 0.15 under / over | 13.85 – 15.65 |
| Molybdenum (Mo) | ≤ 0.20 | No A480 row for ≤0.20% (rows start over 0.20) | Not established—by agreement |
| Copper (Cu) | ≤ 0.50 | 0.03 over | ≤ 0.53 |
Read the product limits as acceptance bounds for a check analysis only. A heat that sits outside the Table 1 melt range is non-conforming even if a later product analysis lands inside the widened band, so the certificate should always show the ladle analysis first. Molybdenum is capped at 0.20% in Table 1, but A480 Table A1.1 has no tolerance row at that level, so any product-analysis allowance for Mo is by agreement.
Mechanical Properties of ASTM A312 UNS S30600
Table 4 sets the room-temperature tension requirements for UNS S30600: 78 ksi [540 MPa] tensile strength and 35 ksi [240 MPa] yield strength minimum, with elongation of 35% longitudinal / 25% transverse minimum. The table below shows those values in the form used on the specification, and the mill certificate should report actual results against each line.
| Property (Table 4) | UNS S30600 |
|---|---|
| Tensile strength, min | 78 ksi [540 MPa] |
| Yield strength (0.2% offset), min | 35 ksi [240 MPa] |
| Elongation in 2 in. or 50 mm (or 4D), min | 35% longitudinal / 25% transverse |
| Hardness | No maximum listed in Table 4 |
The comparison table places S30600 beside TP304L, TP304, and its sister S30601 so the Table 4 floors can be read together.
| Grade | UNS | Tensile min, ksi [MPa] | Yield min, ksi [MPa] |
|---|---|---|---|
| TP304L | S30403 | 70 [485] | 25 [170] |
| TP304 | S30400 | 75 [515] | 30 [205] |
| — | S30600 | 78 [540] | 35 [240] |
| — | S30601 | 78 [540] | 37 [255] |
S30600 has a slightly higher floor than TP304, at 78/35 ksi, but strength is rarely the design driver in acid service; wall thickness is normally set by corrosion allowance and licensor practice. No hardness maximum applies, and elevated-temperature allowables must come from the governing code for this UNS.
No hardness maximum is set for this grade in Table 4, so a hardness figure on a certificate is information rather than an acceptance criterion unless your order adds one. If a project specification imposes hardness or impact testing, write it on the purchase order so the mill can plan the test pieces before the pipe is cut.
Dimensions, Tolerances and Stock Sizes
Dimensions for ASTM A312 UNS S30600 pipe are normally ordered by NPS and schedule from ASME B36.19, or by outside diameter and wall where the design calls for a non-standard size. Outside-diameter tolerance and wall tolerance come from the specification itself, and wall is read as nominal unless Supplementary Requirement S8 asks for minimum wall. The permitted variations in wall thickness from Table 3 are shown below by NPS band and wall-to-diameter ratio.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
In practice the under-tolerance of 12.5% is the figure that matters for pressure design, because the designer has already sized the nominal wall with that allowance in mind. The over-tolerance varies with NPS and the wall-to-diameter ratio, which matters more for fit-up and weld preparation than for strength. For UNS S30600, whose higher strength or special chemistry often justifies a lighter or more closely engineered wall, confirm whether your calculation assumed nominal or minimum wall before the order is placed.
Stock / Available sizes. The table below shows the representative size band we quote for ASTM A312 UNS S30600, with example OD × wall combinations taken from B36.19 schedules. It is a supply and stock-enquiry range rather than a promise that every size sits on the floor today: for S30600 availability is genuinely limited, so expect most sizes, including common Sch 10S and 40S, to be planned as mill orders. Special OD, special wall, and cut lengths are always handled on enquiry.
| Representative size | Example OD × wall | Typical schedules / notes |
|---|---|---|
| NPS 1/2 – 2 | 21.34 × 2.77 mm (NPS 1/2 Sch 40S); 60.33 × 3.91 mm (NPS 2 Sch 40S) | Sch 10S / 40S / 80S; small-bore process and instrument take-offs |
| NPS 2-1/2 – 6 | 88.90 × 5.49 mm (NPS 3 Sch 40S); 168.28 × 3.40 mm (NPS 6 Sch 10S) | Sch 10S / 40S / 80S; the most frequent enquiry band |
| NPS 8 – 12 | 219.08 × 8.18 mm (NPS 8 Sch 40S); 323.85 × 4.57 mm (NPS 12 Sch 10S) | Sch 10S / 40S; confirm SML or WLD route on enquiry |
| NPS 14 – 24 | 406.40 × 4.78 mm (NPS 16 Sch 10S); 609.60 × 9.53 mm (NPS 24 Sch 40S) | Sch 10S / 40S; usually mill-order, mostly welded |
| Special OD × wall | Any OD and wall the mill can qualify | On enquiry: state OD, nominal or minimum wall, and length practice |
Read the example sizes as orientation for writing the enquiry, not as a price list. When you send a size list we check live availability line by line, separate what can ship from existing material from what needs a mill slot, and give the lead time for each group so the purchase order can be split if the schedule demands it.
Equivalent Grades
Buyers often arrive with a trade name, a plate designation, or a European number rather than the A312 row. The table below maps the names we see on enquiries for UNS S30600, but only the ASTM A312 grade and UNS number are contractual on this page; everything else is a cross-reference that needs checking against its own standard.
| Designation | Notes |
|---|---|
| ASTM A312 UNS S30600 | Governing grade on this page (no TP name) |
| ASME SA-312 UNS S30600 | Separate Code standard; dual mark only when the order names both |
| EN 1.4361 | Commonly cited European high-silicon austenitic; verify in the EN standard |
| ASTM A312 UNS S30601 | Higher-silicon sister; not interchangeable without review |
| Producer trade names | Order by UNS S30600, not by trade name |
The ASME SA-312 row is listed because some Code projects require it, not because it is a synonym. ASME SA-312 is a separate standard adopted into the Boiler and Pressure Vessel Code, and the SA312 UNS S30600 page covers that document on its own terms. When both marks are wanted, the order should name both specifications and their editions so the certificate can state compliance with each.
Heat Treatment and Delivery Condition
Unlike most A312 grades, S30600 has its own row in Table 2: solution anneal at 2010–2140 °F [1100–1170 °C], followed by water quench or rapid cooling under Table 2 note D. The higher, ranged temperature dissolves silicon-rich phases and gives a homogeneous austenitic structure, and annealing at the 1900 °F level used for 304 would not comply. S30600 is not among the grades that must be reheated before quench, so seamless pipe may be quenched directly after hot forming if it is at or above 2010 °F. Because the window has both an upper and a lower limit, an over-temperature anneal is just as non-conforming as an under-temperature one.
Delivery condition for UNS S30600 is solution annealed, then descaled by pickling or by blasting and pickling, straightened, and cut to the ordered length practice. HCW pipe receives its cold reduction before the final anneal, so cold work is never the delivered condition. Ask for the actual annealing temperature and cooling method to be recorded on the certificate, because a reviewer cannot otherwise confirm the Table 2 requirement from the document alone.
Corrosion Resistance
ASTM A312 contains no corrosion table, so the following is engineering commentary rather than a specification requirement. S30600 is built for hot concentrated sulfuric acid, where its high silicon content forms a protective film that ordinary austenitic grades cannot. In that service it is often used in place of cast iron or alloys that rely on anodic protection, but the performance depends strongly on acid strength, temperature, and velocity, so licensor guidance is the real acceptance basis.
The ultra-low carbon ceiling protects welded joints against intergranular attack in oxidizing acids such as nitric and nitric-sulfuric mixtures. Impurities in the acid, especially fluorides and chlorides from metallurgical off-gas plants, can shorten service life considerably, and the alloy should not be assumed suitable for chloride-bearing water or reducing acids.
Applications of ASTM A312 UNS S30600 Pipe
Applications for ASTM A312 UNS S30600 pipe are concentrated in sulfuric acid plants and related oxidizing-acid duties. The table below summarizes the typical roles, with the notes that most often affect the decision.
| Application | Role of S30600 | Note |
|---|---|---|
| Sulfuric acid plants | Acid circulation lines, distributor piping, absorption tower connections | Follow licensor guidance on velocity |
| Acid coolers and heat exchangers | Connection piping and headers | Anodic protection used in some designs |
| Nitric acid production | Process lines in oxidizing environments | Low C prevents intergranular attack |
| Mixed acid service | Nitric–sulfuric mixtures in chemical synthesis | Confirm with corrosion testing |
| Oleum and acid storage transfer | Transfer lines where cast iron is impractical | Check temperature limits |
| Metallurgical acid plants | Acid from smelter off-gas recovery | Impurities (fluorides, chlorides) affect life |
Treat the table as a starting point for discussion with the process licensor or corrosion engineer, not as an approval. Code allowable stresses, temperature limits, and any owner material lists decide whether UNS S30600 is acceptable on a given line, and those checks should be made before the pipe is ordered rather than after it arrives.
Weldability
S30600 can be welded by GTAW and GMAW with low heat input and careful interpass control, because high-silicon austenitic weld metal is sensitive to hot cracking. It is not listed in Table 6, so ASTM A312 names no AWS A5.9 class and filler selection is by agreement; producers offer matching high-silicon consumables, and a standard 308L or 316L filler would leave the weld with far lower acid resistance than the pipe. Qualify the procedure on S30600 and follow the alloy producer’s welding guidance.
Qualify the procedure on UNS S30600 itself rather than on a convenient 304 coupon, because the qualification has to demonstrate the strength and soundness of this chemistry. Clean joint preparation, controlled heat input and interpass temperature, and a back-purged root are the normal baseline; the certificate for any WLD pipe should also state whether filler metal was used in the longitudinal seam.
Surface Finishes
Surface condition for ASTM A312 UNS S30600 pipe should be stated on the purchase order rather than left to mill default. On stainless pipe, residual scale, embedded free iron, and chloride contamination from handling can matter as much as the nominal finish name, and they are far easier to prevent at the mill than to correct on site.
- Annealed and pickled the standard delivery after solution treatment for process piping
- Blasted and pickled when heavier scale needs mechanical help before chemical descaling
- Bright annealed by agreement, generally on smaller sizes where the furnace atmosphere can be controlled
- Passivated or polished by agreement, with the method and acceptance criteria written on the order
For UNS S30600, a clean pickled surface free of embedded iron is essential, since iron contamination can initiate attack in hot acid; bright or polished finishes are rarely needed. If the line will be inspected for surface iron, specify the test method at the enquiry stage so that the packing and handling plan supports it.
Inspection and Testing
The base acceptance package for ASTM A312 UNS S30600 pipe combines heat analysis, tension testing, the flattening or bend test that applies to the manufacturing type, and a hydrostatic or non-destructive electric test on every length. Visual and dimensional inspection confirm the size and surface before marking. For S30600 the certificate should report silicon, carbon, phosphorus, sulfur, copper, and molybdenum against their tight limits, and should state the actual anneal temperature inside the 2010–2140 °F window.
Supplementary requirements are optional until they are written on the order. The options buyers request most often for this grade are summarized below, and each one adds test time that should be allowed for in the delivery schedule.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms chemistry on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S8 minimum wall | Wall interpreted as minimum rather than nominal |
| S9 weld decay | Compares weld and base-metal loss rates |
Third-party inspection, witness points, and EN 10204 3.2 certification are available when the order names the inspection agency. Agree the hold points before production starts, because witnessing a hydrotest or a tension test after the fact is not possible.
Packaging and Shipping
ASTM A312 UNS S30600 pipe is packed for handling and for ocean or land transport. Each length is marked with ASTM A312, the grade UNS S30600, the manufacturing type, size, heat number, and the test method used, with SA-312 added only when the order asks for dual marking. Bundle lists repeat the heat numbers so receiving can match pipe to certificates without opening every wrap.
- End caps or bevel protectors fitted as ordered
- Bundles strapped with protected contact points to limit iron pick-up
- Wooden cases or seaworthy bundles for export, with moisture protection for sea freight
- Small-bore or polished pipe cased separately where damage risk is higher
Stainless pipe should not be stored or lifted in contact with carbon steel, and for a specialty grade such as UNS S30600 it is worth keeping the material segregated by heat on arrival, since mixing it with common 304 stock is the most frequent cause of misuse on site.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless pipe, and for a specialty grade such as ASTM A312 UNS S30600 we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 heat analysis, the Table 4 tension results, and the heat-treatment record, and we tell you early when a size or route is a mill order instead of letting the lead time surprise you.
- Understanding of the individually listed Table 2 anneal window and the tight impurity limits of acid-service alloys
- Clear advice on sister grades under ASTM A312, so UNS S30600 is not confused with a commoner alloy that looks similar on paper
- Honest separation of specification requirements from producer or market guidance in every document we send
- EN 10204 3.1 certificates as standard, with third-party inspection and 3.2 certification on request
The aim is a delivery that clears receiving inspection on the first review. That means the certificate, the stencil, and the purchase order all say the same thing about grade, UNS number, manufacturing type, size, and heat treatment, and that any agreed variation is written down before the pipe is made.
Supply Capability
SHH STEEL can supply ASTM A312 UNS S30600 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade, and each line can be narrowed to your project specification.
| Item | SHH STEEL capability for UNS S30600 |
|---|---|
| Standard | ASTM A312 / A312M, UNS S30600 |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD and wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | Single random, double random, or cut to length |
| Heat treatment | 2010–2140 °F [1100–1170 °C] solution anneal (Table 2, individually listed) with rapid cooling |
| Filler guidance | Not listed in Table 6; filler by agreement (matching high-Si consumable recommended by producers) |
| Testing | Tension (78/35 ksi), flattening or bend, hydrostatic or electric test per length; S1, S5, S7, S8, S9 on order |
| Documents | EN 10204 3.1 with full Table 1 analysis; 3.2 and third-party inspection on request |
| Trade terms | FOB, CFR, CIF, EXW and other agreed Incoterms |
Stock / Available sizes. The representative band for UNS S30600 is NPS 1/2 to 24 in Sch 10S, 40S, and 80S as listed under Dimensions. Selected common OD × wall combinations may be available from existing material, while heavy-wall seamless, unusual schedules, and special cut lengths are normally mill orders. We do not publish stock part numbers or tonnage claims for this grade; ask for a live check against your size list instead.
Enquiries move fastest when they state the A312 edition, UNS S30600, the manufacturing type, NPS or OD × wall (and whether the wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements. Dual SA-312 marking, bevelled ends, and cut lengths are available on confirmed orders when the order says so.
FAQ
-
Is ASTM A312 UNS S30600 the same as ASME SA-312 UNS S30600?
- They are two independent standards. ASTM A312/A312M is the ASTM product specification, and ASME SA-312 is the separate document adopted into the Boiler and Pressure Vessel Code. The technical rows for UNS S30600 are closely aligned in current editions, but a pipe is only certified to the document named on the order, so when both are needed the purchase order should list both specifications and editions and the certificate should state compliance with each.
-
What is the UNS number for ASTM A312 UNS S30600?
- This high-silicon alloy has no TP name in A312 Table 1; it is ordered as UNS S30600 and is often known by a producer trade name. The UNS number should appear on the mill certificate and on the stencil next to the ASTM A312 mark, because a trade name alone makes it hard for receiving inspection to tie the chemistry on the certificate to the pipe in the rack.
-
What are the tensile and yield requirements for ASTM A312 UNS S30600 pipe?
- Table 4 requires 78 ksi [540 MPa] tensile strength and 35 ksi [240 MPa] yield strength minimum, with elongation of 35% longitudinal / 25% transverse minimum. These are room-temperature minimums for acceptance only; design allowables at temperature come from the applicable piping code, and they should be checked there before a wall thickness is fixed.
-
What heat treatment does ASTM A312 UNS S30600 pipe receive?
- S30600 has its own Table 2 row: solution anneal within 2010–2140 °F [1100–1170 °C] and water quench or rapid cool per note D. The 1900 °F default used for most grades does not apply. The delivered condition is solution annealed and descaled, and the certificate should record the actual annealing temperature and the cooling method so a reviewer can confirm the requirement without asking the mill.
-
Which filler metal is used to weld ASTM A312 UNS S30600?
- S30600 is not listed in Table 6, so ASTM A312 assigns no AWS A5.9 class; producers offer matching high-silicon fillers, and the agreed consumable must be recorded because a 308L or 316L weld would lose the acid resistance of the base metal. Whatever is chosen should be recorded on the WPS and PQR, and the procedure should be qualified on UNS S30600 base metal so that the joint strength and soundness are demonstrated on the real chemistry.
-
Is ASTM A312 UNS S30600 pipe available seamless and welded?
- Yes. ASTM A312 allows seamless (SML), welded (WLD), and heavily cold-worked (HCW) pipe for UNS S30600, all meeting the same chemistry, tension, and heat-treatment rules. Seamless is usual for heavy wall and high pressure, while welded is often more economical in thin walls and larger diameters; state the accepted route on the order.
-
What sizes of ASTM A312 UNS S30600 pipe can SHH STEEL supply?
- We quote NPS 1/2 to 24 in Sch 10S, 40S, and 80S as the representative band, plus NPS 1/8 and up and special OD and wall by agreement. Some common sizes may be available from existing material, while heavy-wall seamless and unusual schedules are normally mill orders, so send a size list for a live check.
-
What documents come with ASTM A312 UNS S30600 pipe?
- Each shipment carries an EN 10204 3.1 mill test certificate showing the A312 edition, UNS S30600, manufacturing type, heat number, the full Table 1 heat analysis, Table 4 tension results, heat treatment, and the hydrostatic or electric test. Third-party inspection and 3.2 certification can be added when the order names the agency.
-
What is the difference between UNS S30600 and UNS S30601?
- Both are high-silicon acid-service alloys with the same 2010–2140 °F Table 2 anneal and a 78 ksi tensile floor. S30601 carries 5.0–5.6% silicon and 17.0–18.0% nickel against 3.7–4.3% and 14.0–15.5% for S30600, and its yield floor is 37 ksi instead of 35 ksi. The choice follows acid strength and temperature.
-
Why is UNS S30600 used in sulfuric acid plants?
- Its 3.7–4.3% silicon forms a protective silica-rich film in hot concentrated sulfuric acid, where 304L and 316L corrode quickly. That makes it suitable for acid circulation, distributor, and cooler connection piping, provided acid strength, temperature, and velocity stay within the licensor’s guidance.
-
Can UNS S30600 be annealed at 1900 °F like TP304?
- No. Table 2 lists S30600 individually at 2010–2140 °F [1100–1170 °C], so an anneal at 1900 °F does not comply and would not fully dissolve silicon-rich phases. The certificate should show an actual temperature inside that window, followed by a water quench or rapid cool.
Conclusion
ASTM A312 UNS S30600 (UNS S30600) is the high-silicon, ultra-low-carbon alloy of the series for hot concentrated sulfuric and other oxidizing acids, with its own 2010–2140 °F Table 2 anneal and a 78/35 ksi floor. The specification fixes C ≤0.018%, Mn ≤2.00%, P ≤0.02%, S ≤0.02%, Si 3.7–4.3%, Cr 17.0–18.5%, Ni 14.0–15.5%, Mo ≤0.20%, and Cu ≤0.50%, a Table 4 floor of 78 ksi [540 MPa] tensile and 35 ksi [240 MPa] yield, and 2010–2140 °F [1100–1170 °C] solution anneal (Table 2, individually listed) with rapid cooling heat treatment, while filler selection is by agreement because S30600 is not listed in Table 6. Put the manufacturing type, size and wall basis, finish, and any supplementary tests on the purchase order, and review the EN 10204 3.1 certificate against Tables 1, 2, and 4 before release. SHH STEEL can supply ASTM A312 UNS S30600 pipe to the edition you name; compare sister grades on the A312/A312M hub, or send your size list to admin@steelspecs.com.