ASME SA312 TP316N Stainless Steel Pipe | ASME SA312 Stainless Steel - SHH STEEL

ASME SA312 TP316N Stainless Steel Pipe | SA 312/SA 312M

ASME SA312 TP316N (UNS S31651) nitrogen-strengthened stainless steel pipe in seamless, welded and HCW forms, with Mo 2–3%, N 0.10–0.16% and 80/35 ksi minima, supplied by SHH STEEL with EN 10204 3.1 MTCs.
Grade
TP316N / UNS S31651
Standard
ASME SA312 / SA 312M (ASTM A312 / A312M)
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASME SA312 TP316N Stainless Steel Pipe

ASME SA-312/SA-312M covers seamless, welded and heavily cold-worked austenitic stainless steel pipe for high-temperature and general corrosive service, and it is technically aligned with ASTM A312/A312M of the referenced edition. Grade TP316N is listed in Table 1 as UNS S31651. For pressure piping and code work, cite the grade, the UNS number and the edition of the standard on the purchase order and on the mill test certificate, rather than relying on a market label that several neighbouring grades share.

TP316N is the nitrogen-strengthened member of the Mo-bearing 316 family. Table 1 keeps the familiar TP316 envelope—Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00% and C ≤0.08%—and then makes nitrogen a required range of 0.10–0.16%, not a residual. That intentional nitrogen is what lifts the Table 4 floors to 80 ksi [550 MPa] tensile and 35 ksi [240 MPa] yield, five ksi above TP316 on both lines. It is not an H grade: there is no carbon floor, no Table 5 grain-size rule and no clause 6.2 reheat language. Table 2 does not list S31651 individually, so the default 1900 °F [1040 °C] solution anneal with rapid cooling applies, and Table 6 maps the grade to the ER316 filler family.

SHH STEEL can supply ASME SA312 TP316N stainless steel pipe to the edition named on the enquiry, in seamless (SML), welded (WLD) and heavily cold-worked (HCW) forms. We cover ASME B36.19 schedules and special OD and wall combinations by agreement, issue EN 10204 3.1 mill test certificates as standard, and can dual-mark SA-312/A312 when the heat analysis, heat treatment, mechanical tests and marking satisfy both editions named on the purchase order. Tell us the NPS, wall or schedule, finish, length practice and any product-analysis or supplementary tests at enquiry stage, and we will confirm stock or mill rolling against those details.

Common commercial names and how they map to the ordered product are listed below. Use the full SA-312/A312 designation on the purchase order rather than market shorthand alone, because the shorthand is where grade substitutions usually start.

  • ASME SA312 TP316N / SA-312 Grade TP316N — preferred marking language for ASME-code and dual-marked pipe
  • ASTM A312 TP316N — same chemistry and tensile tables when the ASTM edition is referenced
  • UNS S31651 — unified numbering identity used on MTCs, stencils and ASME Section II Part D cross-references
  • 316N / 316N stainless steel pipe — market shorthand; confirm N 0.10–0.16% and the 80/35 ksi Table 4 row on the order

TP316N is not a drop-in for ASME SA312 TP316 Stainless Steel Pipe, ASME SA312 TP316LN Stainless Steel Pipe, ASME SA312 TP316H Stainless Steel Pipe or ASME SA312 TP304N Stainless Steel Pipe, even though all of them get called “316” or “N-grade” in the market. Against TP316, the difference is the mandatory nitrogen band and the higher 80/35 ksi floors. Against TP316LN, the trade runs the other way: LN caps carbon at 0.035% for welded aqueous service but drops back to 75/30 ksi. TP316H adds a 0.04–0.10% carbon band and grain-size control for creep service, which TP316N does not have. TP304N shares the nitrogen idea but carries no molybdenum, so it gives up the chloride margin that the 2–3% Mo brings. Hub: ASME SA 312/SA 312M.

Manufacturing Types (SML / WLD / HCW)

SA-312 defines three manufacturing routes that may be marked on finished TP316N pipe. The route is a purchase-order decision driven by design code, size range, wall thickness and inspection preference. It does not change the Table 1 chemistry of UNS S31651, and every route must still finish with the solution anneal required by SA-312.

  • Seamless (SML) — no welding at any stage. Preferred for small-bore and thick-wall pressure pipe, and wherever the piping class excludes welded product.
  • Welded (WLD) — automatic welding without filler metal, finished so the pipe meets dimensional and mechanical requirements after final heat treatment. Common for larger NPS lines where the code accepts welded austenitic pipe.
  • Heavily cold-worked (HCW) — welded pipe cold worked at least 35% in wall and weld before the final anneal, with the weld radiographed before cold work. Ordered when tighter OD and wall consistency matters.

Each finished length is hydrostatically tested or nondestructively electrically tested, and the manufacturer may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser agrees to a system test instead. State SML, WLD or HCW explicitly on the enquiry; bids that differ only in manufacturing type are a common evaluation trap, and the same letters should appear on the stencil and the MTC.

Chemical Composition of SA312 TP316N

Melting analysis (heat / ladle analysis) — Table 1

The table below is the SA-312 Table 1 heat analysis for TP316N / UNS S31651. Values are maximum unless a range is shown, and an ellipsis (…) means no requirement. These are the numbers the mill must report on the certificate, and they are the numbers receiving inspection should check first.

Element TP316N / UNS S31651 melting analysis
Carbon (C) ≤ 0.08
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 16.0 – 18.0
Nickel (Ni) 10.0 – 14.0
Molybdenum (Mo) 2.00 – 3.00
Nitrogen (N) 0.10 – 0.16

Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1

When product analysis is ordered (Supplementary Requirement S1 or PO wording), the check analysis may vary from the Table 1 limits by the A480 tolerances below. Product analysis is not automatic, so order it explicitly if your project needs it rather than assuming ladle values will satisfy the client inspector.

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.08 0.01 over ≤ 0.09
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 16.0 – 18.0 0.20 under / over 15.80 – 18.20
Nickel (Ni) 10.0 – 14.0 0.15 under / over 9.85 – 14.15
Molybdenum (Mo) 2.00 – 3.00 0.10 under / over 1.90 – 3.10
Nitrogen (N) 0.10 – 0.16 0.01 under / over 0.09 – 0.17

Two comparisons matter on the certificate review. Against TP316, the C/Cr/Ni/Mo pattern is identical and the only chemistry difference is the required N 0.10–0.16%, which in turn justifies the higher tensile row. Against TP316LN, the nitrogen band is the same but LN limits carbon to 0.035% and is released at 75/30 ksi. On product analysis, the A480 tolerance for nitrogen in this band is 0.01, and molybdenum carries ±0.10 across the 2–3% range. A TP316N certificate that omits the nitrogen result is incomplete, however good the other numbers look, because nitrogen is the element that defines the grade.

Mechanical Properties of SA312 TP316N

Property TP316N
Tensile, min 80 ksi [550 MPa]
Yield, min 35 ksi [240 MPa]
Elongation 35% L / 25% T

The 80/35 ksi row is the release floor for TP316N, and it is the reason most buyers specify the grade in the first place. A mill offering “316N chemistry” with only a 75 ksi tensile result has not supplied TP316N, and the heat should not be released against a TP316 acceptance line simply because the chemistry looks close. Designers should take allowable stresses from the code tables for UNS S31651 rather than borrowing TP316 numbers, and the higher yield can justify a thinner wall only after the governing code minimum thickness has been checked.

Actual certificate values are usually comfortably above the minima, but design and acceptance still use the Table 4 row unless the purchase order states higher guaranteed values. Record the row on the datasheet so fabricators and inspectors do not substitute a sister grade’s strength line from memory, and make sure the tension test on the MTC is traceable to the heat and lot that was shipped.

Dimensions and Tolerances

TP316N pipe is normally ordered to ASME B36.19 schedules, with heavier B36.10 walls and special OD and wall combinations available by agreement. Wall thickness tolerance follows SA-312 Table 3, and outside diameter variations follow A999/A999M for the ordered size.

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%

Source: SA-312 Table 3; outside diameter variations per A999/A999M. Cut lengths should not be shorter than ordered, and random or fixed length practice should be stated on the enquiry. Special walls and non-standard sizes need written mill agreement before rolling slots are booked, so raise them early if your design does not fit a standard schedule.

Equivalent Grades

Designation Notes
ASME SA-312 TP316N / UNS S31651 Governing specification for ASME code work
ASTM A312 TP316N / UNS S31651 Same chemistry and tensile rows for the referenced edition
UNS S31651 Unified numbering identity on MTC and stencil

Cross-references to EN or other national numbers are not given here, because SA-312 does not define them and near-equivalents rarely match every Table 1 limit. If a project needs a cross-standard equivalence, treat it as an engineering decision against both specifications rather than a catalogue lookup. Dual SA-312/A312 certification is straightforward when both editions are named on the order. Related grades for comparison: ASME SA312 TP316 Stainless Steel Pipe, ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 TP316H Stainless Steel Pipe, ASME SA312 TP316LN Stainless Steel Pipe, ASME SA312 TP304N Stainless Steel Pipe.

Heat Treatment and Delivery Condition

UNS S31651 is not individually listed in Table 2, so the default solution-annealing practice applies: heat to a minimum of 1900 °F [1040 °C] and cool rapidly. TP316N is not an H grade, so there is no Table 5 grain-size requirement and no clause 6.2 reheat rule. Pipe is delivered in the solution-annealed condition, and the certificate should state the heat-treatment temperature and cooling method actually used.

Fabricators who hot form or heavily cold work TP316N bends and fittings should re-anneal to the same practice where the governing code requires it. Cite the ordered edition’s Table 2 default on the enquiry so the mill does not apply a neighbouring grade’s anneal by habit.

Corrosion Resistance

With Mo 2–3%, TP316N gives broadly the same pitting and crevice behaviour as TP316 in chloride-bearing process streams; the nitrogen is there mainly for strength. It is important not to treat nitrogen as a substitute for low carbon. Intergranular behaviour still depends on carbon level and thermal history, so where sensitization in weld heat-affected zones is the dominant risk, ASME SA312 TP316LN Stainless Steel Pipe or TP316L is usually the better choice. SA-312 publishes no corrosion rates, so service suitability for a specific medium, temperature and crevice geometry needs engineering review rather than a catalogue claim.

Intergranular-corrosion testing to A262 or similar is a supplementary requirement and applies only when written on the purchase order, so state the practice and acceptance criteria if your client needs it. The same applies to any pitting or crevice tests requested by the end user.

Applications of SA312 TP316N Pipe

Application Why TP316N Buyer note
Pressure piping needing a higher yield floor than TP316 80/35 ksi Table 4 row Confirm code allowables for S31651
Mo-bearing process lines where wall weight matters N strengthening with Mo 2–3% Check code minimum wall before down-gauging
Mechanical and structural stainless lines Higher yield than standard 316 Compare TP316LN if low carbon is needed

TP316N is ordered when the designer needs molybdenum-bearing corrosion resistance plus a higher yield floor than commodity TP316, without moving to a duplex or higher-alloy grade. Enquiries should state design pressure and temperature and make clear that the 80/35 ksi row is mandatory, because a mill quoting from commodity 316 stock will often assume 75/30 unless told otherwise.

Weldability

Table 6 maps TP316N to the ER316 family, and that class should be frozen on the WPS and PQR before production welding. Nitrogen in the base metal affects weld-metal strength and dilution, so qualify the procedure on TP316N itself rather than borrowing a plain TP316 PQR, and record heat-input and interpass limits that the welders actually follow. Mill longitudinal welds on WLD and HCW pipe are autogenous and use no filler; Table 6 guidance applies only to field and shop joints made with filler metal.

Use stainless-only tooling and back-purge root passes where the specification calls for a clean root, and keep consumable lot records with the weld traveler when Section IX or B31 documentation applies. NDE extent for girth welds is a fabrication-code decision, separate from the mill hydro or electric test on each length.

Surface Finishes

Most TP316N pipe ships pickled and passivated after the solution anneal, which is the normal finish for process piping. Other finishes are order extras and should be stated on the enquiry, together with whether a roughness target applies to the OD, the ID or both.

  • Annealed and pickled (standard)
  • Bright annealed, by agreement
  • Mechanically polished OD, by agreement
  • Electropolished ID for hygienic service, by agreement

Inspection and Testing

SA-312 sets the minimum test package for every heat and length of TP316N. Supplementary tests are only applied when written on the order, so the inspection and test plan should list them before production starts.

  • Heat analysis to Table 1, including every element with a limit
  • Tension test to the Table 4 row (80 ksi [550 MPa] / 35 ksi [240 MPa])
  • Flattening and, for welded pipe, the applicable weld tests
  • Hydrostatic or nondestructive electric test on each length
  • Visual and dimensional checks to Table 3 and A999
  • Optional: product analysis, IGC test, PMI, UT/RT of welds, EN 10204 3.2 witness

Packaging and Shipping

Each length is marked with SA-312 (and A312 when dual-certified), TP316N / UNS S31651, the manufacturing type, size, heat number and test method. For export, we pack in a way that protects the stainless surface from carbon steel contact and moisture during ocean transit.

  • Plastic end caps on every length
  • Bundles strapped with non-metallic or protected bands
  • Seaworthy wooden cases or crates for polished or thin-wall pipe
  • Segregation from sister grades so stencils cannot be mixed

Why Choose SHH STEEL

SHH STEEL works with qualified stainless mills to supply TP316N to the edition you name, and our job is to make sure what arrives on site matches the datasheet. That starts with reading the enquiry against the actual SA-312 rows—Table 1 chemistry, the 80 ksi [550 MPa] / 35 ksi [240 MPa] Table 4 row and the Table 2 anneal—and flagging mismatches before an order is placed. We are honest where the standard is silent: if Table 6 does not give a clear filler class, we say so rather than inventing one.

  • Seamless, welded and HCW TP316N to SA-312/A312, with dual marking when both editions are ordered
  • EN 10204 3.1 MTCs as standard; 3.2 and third-party witness by arrangement
  • Full Table 1 reporting, including nitrogen on every heat
  • B36.19 schedules plus special OD and wall by agreement
  • Export packing and heat traceability from mill to site

Supply Capability

We supply TP316N pipe from mill production and selected stock, with lead time depending on size, wall and manufacturing type. The table summarises what we can offer; please confirm the details for your order on enquiry.

Item Supply
Grade TP316N / UNS S31651
Standard ASME SA-312/SA-312M, ASTM A312/A312M (dual by agreement)
Routes SML, WLD, HCW
Sizes ASME B36.19 schedules; special OD and wall by agreement
Filler guidance ER316 (Table 6 family listing)
Certificates EN 10204 3.1; 3.2 by arrangement

Standard schedules can often ship from stock or short mill runs, while heavy-wall seamless and special sizes need a rolling slot. Send the edition, grade and UNS, size list, quantities and required date, and we will separate stock lengths from made-to-order items in our quotation so your site dates are realistic.

FAQ

Is ASME SA312 the same as ASTM A312?
For chemistry, tensile requirements, manufacturing types and most testing language, ASME SA-312/SA-312M matches ASTM A312/A312M of the referenced edition. Dual SA312/A312 marking for TP316N is common when ordered. Name both editions on the purchase order and the certificate so inspectors can verify the heat against the exact books you cited; a bare market stamp does not prove dual certification.
What is the UNS number for TP316N?
Table 1 lists TP316N as UNS S31651. Use that UNS on the purchase order, the stencil and the MTC so the chemistry and tensile rows stay unambiguous. When a project mixes plate, fittings and pipe, carry the same UNS language across all forms, but still order pipe to SA-312/A312 rather than to a plate specification.
TP316N vs TP316 — which should I order?
TP316N adds a mandatory N 0.10–0.16% and raises the Table 4 floors to 80 ksi tensile and 35 ksi yield, while standard TP316 uses 75/30 ksi with no nitrogen requirement. Order TP316N when the design takes credit for the higher strength; otherwise TP316 is easier to source. Settle the grade on the datasheet before comparing price, because a late switch means a material change notice.
TP316N vs TP316LN — which should I order?
TP316LN limits carbon to 0.035% with the same N 0.10–0.16% band and is released at 75/30 ksi, while TP316N allows C up to 0.08% and is released at 80/35 ksi. Choose LN when welded aqueous service and sensitization drive the decision, and TP316N when the design depends on the higher strength row. The two are not interchangeable on a certificate.
Seamless vs welded TP316N — which is better?
Neither is universally better. Seamless suits small-bore, thick-wall and pressure parts where the piping class excludes welds, while welded and HCW pipe are economical for larger sizes and offer good wall consistency. Choose the route your design code and datasheet allow, state SML, WLD or HCW on the order, and confirm the same letters on the marking and certificate.
Hydrostatic test vs NDE — which do I get?
Each length of TP316N is either hydrotested or nondestructively electrically tested, and the manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification requires one method, state it on the order and check that the chosen test appears on the certificate for every length; a silent mill choice is not an approved project method.
What heat treatment applies to TP316N?
UNS S31651 is not individually listed in Table 2, so the default solution anneal at a minimum of 1900 °F [1040 °C] with rapid cooling applies. TP316N is not an H grade, so there is no Table 5 grain-size rule. Delivery is in the solution-annealed condition, and the certificate should state the temperature and cooling used so the record is complete.
What Table 1 chemistry defines TP316N?
Table 1 for UNS S31651: C ≤0.08%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00% and N 0.10–0.16%. These are melting-analysis limits from the ordered edition, so do not invent tighter catalogue windows. When product analysis is needed, order it explicitly through Supplementary Requirement S1 or PO wording, and the A480 tolerances shown in the chemistry section then apply.
What are the Table 4 tensile requirements for TP316N?
Table 4 minima for TP316N are 80 ksi [550 MPa] tensile and 35 ksi [240 MPa] yield, with elongation of 35% longitudinal and 25% transverse. Actual certificate values are usually higher, but design and acceptance use Table 4 unless the order states higher guarantees. Record the row on the datasheet so nobody substitutes a sister grade’s line from memory.
What filler metal should I use to weld TP316N pipe?
Table 6 maps TP316N to the ER316 family. Freeze the AWS or EN class on the WPS and PQR before production welding and qualify the procedure on TP316N base metal. Mill longitudinal welds on WLD and HCW pipe are autogenous, so Table 6 guidance applies only to joints made with filler, not to the mill seam.
Why are the Table 4 minima higher for TP316N?
Nitrogen in solid solution strengthens austenite, and the required 0.10–0.16% N in Table 1 is what supports the higher Table 4 floors of 80 ksi tensile and 35 ksi yield, compared with 75/30 ksi for TP316. That is also why a heat with nitrogen below the band cannot be certified as TP316N even if its tensile results happen to be high.
Is TP316N an H grade for high-temperature creep service?
No. TP316N has no carbon floor, no Table 5 grain-size requirement and no clause 6.2 reheat rule, so it is not an H grade. If the design is governed by creep or stress-rupture at elevated temperature, TP316H is the grade written for that duty. Use the code allowables for UNS S31651 and do not stretch a TP316N heat into an H-grade basis.

Conclusion

ASME SA312 TP316N (UNS S31651) is nitrogen-strengthened 316 pipe: Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00%, C ≤0.08% and a required N 0.10–0.16%, released against 80/35 ksi Table 4 minima with a Table 2 default 1900 °F [1040 °C] anneal and ER316-family filler. It is not an H grade and not a drop-in for TP316, TP316LN or TP316H. State the manufacturing type, schedule or wall, finish and any supplementary tests on the enquiry, and ask for the heat certificate with nitrogen and tensile results side by side. For stock checks, mill certificates or dual SA-312/A312 supply questions, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X