ASME SA312 TP316 Stainless Steel Pipe | SA 312/SA 312M
What is ASME SA312 TP316 Stainless Steel Pipe
ASME SA-312/SA-312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe for high-temperature and general corrosive service. TP316 / UNS S31600 is the molybdenum-bearing chromium–nickel grade that most engineers simply call “316”. Table 1 sets C ≤0.08%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 16.0–18.0%, Ni 10.0–14.0%, and Mo 2.00–3.00%, with no nitrogen requirement. That mandatory molybdenum is the reason buyers move up from TP304: it gives noticeably better resistance to pitting and crevice attack in chloride-bearing water, brines, and many process chemicals.
Table 4 sets 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield minimum with 35% longitudinal and 25% transverse elongation, the same floors as ASME SA312 TP304 Stainless Steel Pipe. The pipe is solution annealed at the Table 2 default of 1900 °F [1040 °C] minimum followed by rapid cooling, and Table 6 lists ER316 as the recommended filler. Because carbon may run up to 0.08%, projects that weld heavily and cannot anneal afterwards often specify ASME SA312 TP316L Stainless Steel Pipe or a dual 316/316L heat instead.
SHH STEEL can supply ASME SA312 TP316 stainless steel pipe to the edition named on your enquiry, in seamless (SML), welded (WLD), and heavily cold-worked (HCW) form. We quote ASME B36.19 schedules as well as special OD and wall by agreement, ship with EN 10204 3.1 mill test certificates that report the full Table 1 chemistry and the Table 4 results, and offer dual SA-312/A312 marking when the heat and tests meet both editions on the purchase order. Please confirm NPS, wall or schedule, finish, length practice, and any supplementary tests when you enquire.
The names below are the ones buyers use day to day, and they map to the ordered product as shown. Always put both the TP name and the UNS number on the order so there is no doubt at receiving inspection.
- ASME SA312 TP316 / UNS S31600 — preferred marking language for ASME-code and dual-marked pipe
- ASTM A312 TP316 — same grade tables when the ASTM edition is referenced
- “316 stainless pipe” — market shorthand; acceptable in conversation, but the certificate must show Mo 2.00–3.00%
- EN 1.4401 / JIS SUS316 — approximate regional names only, not code substitutes
Sister grades buyers compare with TP316 include ASME SA312 TP316L Stainless Steel Pipe (C ≤0.035% and 70/25 ksi), ASME SA312 TP316H Stainless Steel Pipe (C 0.04–0.10% with H-grade grain-size rules), ASME SA312 TP316N Stainless Steel Pipe (nitrogen-strengthened), ASME SA312 TP316Ti Stainless Steel Pipe (titanium-stabilized), and ASME SA312 TP304 Stainless Steel Pipe when molybdenum is not needed. Grade hub: ASME SA 312/SA 312M.
Manufacturing Types (SML / WLD / HCW)
ASME SA-312 recognizes three manufacturing routes for TP316 pipe, and the route is a purchase-order decision driven by the design code, the size range, wall thickness, and how the owner wants the pipe inspected. The route never changes the chemistry: whichever way the pipe is made, the heat must still meet C ≤0.08%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 16.0–18.0%, Ni 10.0–14.0%, and Mo 2.00–3.00%, and every length must still go through the solution anneal at 1900 °F [1040 °C] minimum before it is released.
- Seamless (SML) — no welding at any stage. Seamless is the usual route for heavy walls, small bores, and high-pressure process lines, and every seamless length still receives the 1900 °F solution anneal before release.
- Welded (WLD) — automatic welding without filler metal, with the weld finished so the pipe meets dimensional and mechanical requirements after the final heat treatment. The strip or plate heat must itself carry the full TP316 chemistry, so ask for the coil or plate heat number on the certificate.
- Heavily cold-worked (HCW) — welded pipe cold worked to at least 35% reduction of wall and weld before the final anneal, again without filler in the longitudinal seam, with the weld radiographed before cold work. Order HCW when the project specifically wants that marking and the process controls SA-312 writes around it.
Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test in place of the hydrotest, and lots for mechanical testing follow clause 11.1. TP316 carries no H-grade lot-marking or grain-size rule, but heat identity must still be stenciled on every length. Dual TP316/TP316L certification is common when one heat meets C ≤0.035% together with the higher TP316 tensile floors.
TP316 is one of the most widely stocked SA-312 grades, so common schedules in welded and seamless form are often available at short notice. Heavy-wall seamless, large-diameter welded, and non-standard walls are usually mill-order items. Enquire with route, sizes, wall, edition year, and whether you need TP316/TP316L dual marking, so we can match stock or plan the heat chemistry from the start.
Chemical Composition of SA312 TP316
Two chemistry layers matter for TP316. The melting (heat or ladle) analysis is mandatory for every heat under SA-312/A312 Table 1, while product analysis on finished pipe applies only when it is ordered through Supplementary Requirement S1 or purchase-order wording. Product tolerances are not printed in SA-312 itself; they come through ASTM A999/A999M §6.3 from ASTM A480/A480M Table A1.1. SHH STEEL reports the actual ladle values and, when ordered, the product values, and never quotes tighter catalogue windows that the standard does not publish.
Melting analysis (heat / ladle analysis) — Table 1
The table below is the heat analysis for TP316 from SA-312/SA-312M Table 1. Values are maximum unless a range is shown, and an ellipsis (…) means the ordered edition sets no requirement for that element. TP316 has no nitrogen, titanium, or niobium requirement in Table 1.
| Element | TP316 (UNS S31600) melting analysis |
|---|---|
| Carbon (C) | ≤ 0.08 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 16.0 – 18.0 |
| Nickel (Ni) | 10.0 – 14.0 |
| Molybdenum (Mo) | 2.00 – 3.00 |
| Nitrogen (N) | … (no requirement) |
Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.08 | 0.01 over | ≤ 0.09 |
| Manganese (Mn) | ≤ 2.00 | 0.04 over | ≤ 2.04 |
| Phosphorus (P) | ≤ 0.045 | 0.010 over | ≤ 0.055 |
| Sulfur (S) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Silicon (Si) | ≤ 1.00 | 0.05 over | ≤ 1.05 |
| Chromium (Cr) | 16.0 – 18.0 | 0.20 under / over | 15.80 – 18.20 |
| Nickel (Ni) | 10.0 – 14.0 | 0.10 under / 0.15 over | 9.90 – 14.15 |
| Molybdenum (Mo) | 2.00 – 3.00 | 0.05 under / 0.10 over | 1.95 – 3.10 |
Source: SA-312 Table 1 TP316 / S31600. Mo 2.00–3.00% mandatory; no N requirement.
Molybdenum is the element to check first on receipt, because it is the only thing that separates TP316 from ASME SA312 TP304 Stainless Steel Pipe on a handheld PMI gun. Chromium is 16.0–18.0% (two points below TP304’s 18.0–20.0%) and nickel is raised to 10.0–14.0% to keep the structure fully austenitic with the molybdenum present. Carbon up to 0.08% is the difference from ASME SA312 TP316L Stainless Steel Pipe, and it matters only where welds or hot work leave the pipe in the sensitizing range without a fresh anneal.
When product analysis is ordered, A480 Table A1.1 widens the Table 1 limits as shown above: carbon may read up to 0.09%, molybdenum 1.95–3.10%, chromium 15.80–18.20%, and nickel 9.90–14.15%. These are acceptance limits for finished pipe, not targets for the melt, and they should be written into the purchase order whenever the owner wants an independent check after delivery.
Mechanical Properties of SA312 TP316
Room-temperature tensile requirements for TP316 come from SA-312 Table 4 and are summarized below. These are minimum release values for the lot, not typical values, and design allowables must always be taken from the governing code tables for UNS S31600 rather than from a neighbouring grade.
| Property | TP316 requirement (Table 4) |
|---|---|
| Tensile strength, min | 75 ksi [515 MPa] |
| Yield strength (0.2% offset), min | 30 ksi [205 MPa] |
| Elongation in 2 in. or 50 mm (or 4D) | 35% longitudinal / 25% transverse, min |
The 75/30 ksi floors match ASME SA312 TP304 Stainless Steel Pipe and sit above the 70/25 ksi of ASME SA312 TP316L Stainless Steel Pipe, which is why a dual 316/316L heat is attractive: it gives the low carbon of the L grade with the higher strength of the straight grade. Table 4 does not list a hardness maximum for TP316, so catalogue Brinell or Rockwell figures should not be treated as acceptance criteria unless they are written on the order. Against ASME SA312 TP201 Stainless Steel Pipe, which has a 38 ksi yield floor, TP316 is the lower-strength but far more corrosion-resistant choice.
Certificate results normally sit comfortably above the minima, but design should still use Table 4 and the code allowable stresses for UNS S31600 unless the mill has accepted higher guaranteed values in writing. Tension and flattening or bend tests run on a lot basis, and supplementary tests apply only when they are listed on the purchase order. Delivery is always the solution-annealed condition.
Dimensions and Tolerances
Dimensional supply for SA312 TP316 pipe follows ASME B36.19 schedules for the common NPS and schedule combinations, with special OD and wall available by agreement when a project needs a section the schedules do not cover. Outside-diameter variations follow ASTM A999/A999M, and wall-thickness variations follow SA-312 Table 3 as summarized below. State on the purchase order whether wall is nominal or minimum (Supplementary S8), because the two readings produce different pipe from the same size line.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
Source: SA-312 Table 3; outside diameter variations per A999/A999M.
- Lengths — single random, double random, or cut-to-length on order
- Cut lengths — typically no more than 1/4 in. [6 mm] over the ordered length unless the PO states a tighter band
- Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen
Many chemical, marine, and pharmaceutical buyers order by OD × wall rather than NPS and schedule, which is fine as long as the enquiry says so clearly. Straightness, end finish, and length tolerance should be written into export orders so receiving inspection has an agreed acceptance basis instead of arguing after arrival. On thin schedules with threaded or socket-weld ends, check that the remaining wall is still adequate after the 12.5% under-tolerance. Jointers are not permitted unless the purchase order allows them, so cut-to-length programmes should include an allowance for fit-up scrap rather than expecting the mill to ship short pieces.
Equivalent Grades
TP316 / UNS S31600 has a close equivalent in ASTM A312 and approximate equivalents in EN and JIS designations. These cross-references help material selection, but none of them is an automatic substitute for ASME pressure-code pipe without an approved material specification and design-code acceptance.
| Designation | Notes |
|---|---|
| ASME SA-312 / ASTM A312 Grade TP316 | Governing pipe product standard for this article |
| UNS S31600 | Unified number listed in Table 1 |
| EN 1.4401 (X5CrNiMo17-12-2) | Approximate wrought Mo austenitic designation; order EN tube/pipe under the relevant EN product specs, not by EN number alone on an SA-312 MTC |
| JIS SUS316 | Approximate Japanese grade name; confirm the Japanese pipe/tube product standard when ordering JIS product |
| Plate counterpart | ASME SA240 316 Stainless Steel Plate for flat product in the 316 family |
EN 1.4401 (X5CrNiMo17-12-2) and JIS SUS316 are close in chemistry but sit under their own product standards, tolerances, and test rules, so they should be ordered to those standards rather than by number on an SA-312 certificate. Within SA-312, ASME SA312 TP316L Stainless Steel Pipe has its own carbon ceiling and lower tensile floors, and the two grades should not be interchanged without engineering review unless the heat is dual certified. Related SA-312 pages: ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 TP316H Stainless Steel Pipe, ASME SA312 TP317L Stainless Steel Pipe, and ASME SA312 TP304 Stainless Steel Pipe.
Heat Treatment and Delivery Condition
TP316 has no individual row in Table 2, so it falls under the default for all grades not individually listed: solution anneal at 1900 °F [1040 °C] minimum, followed by water quenching or another rapid cool fast enough to prevent harmful carbide reprecipitation. Seamless pipe may be quenched directly after hot forming where the edition allows it and the finishing temperature is not below the minimum anneal temperature. HCW product is cold reduced before the final anneal, so cold work is never the delivery condition.
SHH STEEL ships TP316 solution annealed and pickled, or bright annealed by agreement, straightened, cut to the ordered length practice, and hydrotested or electrically tested per length. If pipe is hot bent or formed after delivery, a fresh solution anneal is the safe way to restore corrosion resistance, especially in the higher-carbon end of the 0.08% ceiling. The anneal temperature and cooling method should appear on the certificate so receiving inspection can confirm Table 2 was met.
Corrosion Resistance
SA-312 does not contain a corrosion table, so this section is engineering commentary. The 2.00–3.00% molybdenum in TP316 gives clearly better pitting and crevice resistance than ASME SA312 TP304 Stainless Steel Pipe in chloride-bearing water, seawater splash, brines, and many organic and mildly reducing acids. It is the default grade for a large share of chemical, food, pharmaceutical, and marine piping where TP304 has shown pitting.
- Pitting and crevice corrosion — better than TP304, but warm seawater and stagnant chloride service can still attack TP316
- Intergranular corrosion — a risk only after sensitizing exposure; S7 (A262 Practice E) can be ordered when proof is needed
- Chloride stress corrosion cracking — similar susceptibility to other 300-series grades above about 60 °C
- General corrosion — good in dilute sulfuric, phosphoric, and acetic acid service within normal concentration limits
Where welded joints cannot be annealed and the service is aggressive, ASME SA312 TP316L Stainless Steel Pipe or a dual 316/316L heat is the safer choice. Where chlorides are higher still, consider ASME SA312 TP317L Stainless Steel Pipe or a higher-molybdenum grade rather than relying on TP316 beyond its comfortable range.
Applications of SA312 TP316 Pipe
Applications for TP316 pipe are driven by chloride and chemical resistance that TP304 cannot provide, at a cost well below higher-alloy grades. The table below summarizes where buyers typically specify it.
| Application area | Typical use of TP316 pipe | Selection note |
|---|---|---|
| Chemical and petrochemical | Process lines handling chlorides, acids, and solvents ordered to SA-312 | Confirm fluid compatibility; prefer higher alloys if PREN/corrosion design demands it |
| Offshore / marine topside | Seawater-exposed or brine-adjacent stainless piping | Often TP316L preferred for welded service; confirm project grade |
| Food, beverage, pharma | Hygienic and utility lines where 316 stainless is accepted | State Ra/polish and docs when required |
| Pulp and paper | Bleaching chemicals and aggressive process streams | Review chloride and temperature with corrosion engineering |
| Power and utility | Condensate, feedwater auxiliary, and plant stainless piping | Dual SA312/A312 marking often requested |
| General corrosive service | Where Mo austenitic pipe is specified over 304-class | Do not substitute TP304 when Mo is required on the datasheet |
Typical users include chemical and petrochemical process plants, pulp and paper, food and beverage, pharmaceutical utilities, desalination pre-treatment, and offshore or coastal installations. Enquiries should state the process fluid and temperature, whether the welds will be annealed, whether TP316/TP316L dual marking is wanted, and any S7 corrosion test. When molybdenum is not needed, ASME SA312 TP304 Stainless Steel Pipe is usually cheaper; when welds will stay as-welded in aggressive service, compare with ASME SA312 TP316L Stainless Steel Pipe.
Weldability
TP316 welds readily by GTAW, GMAW, SMAW, and orbital processes with normal austenitic practice: clean joints, controlled heat input and interpass temperature, and back-purged roots. Table 6 lists ER316 (UNS S31680 / W31640) as the recommended filler for TP316 when mill seam repairs use filler metal under Section 15, and ER316 or ER316L is the usual matching consumable for field girth welds documented on the WPS and PQR.
- GTAW (TIG) — preferred for roots and thin walls where weld-metal cleanliness matters
- GMAW / SMAW — productive for fill and cap passes on thicker walls with qualified procedures
- Orbital GTAW — common for repetitive hygienic or high-integrity girth joints
- Back-purge — argon or equivalent to protect the ID from heat tint
With carbon up to 0.08%, the HAZ can sensitize if the joint sees slow cooling or long exposure in the carbide range, so low heat input or a post-weld anneal is good practice in corrosive duty. Mill longitudinal welds on WLD and HCW pipe are made without filler, so Table 6 applies to repair and fabrication joints only, and girth-weld NDE is a fabrication-code decision separate from the mill hydro or electric test.
Surface Finishes
Surface condition for SA312 TP316 pipe should be stated on the purchase order rather than left to mill default. For stainless pipe, embedded free iron, residual scale, and chloride-bearing residues are where corrosion starts, so the finish is part of the material performance and not just appearance. The finishes we regularly quote for this grade are listed below.
- Annealed and pickled (AP) — solution annealed at 1900 °F [1040 °C] minimum, then descaled in acid pickle or an equivalent process to a matte grey finish; the standard choice for process pipe
- Blasted and pickled — common on heavy-wall seamless where blasting first makes scale removal more reliable
- Bright annealed (BA) — annealed in a protective atmosphere where mill capability exists for the size; the anneal temperature still has to meet the Table 2 practice for TP316
- Mechanically polished — OD and/or ID polish to an agreed grit or Ra when ordered; polishing never replaces the solution anneal
- Bead-finished welded OD — weld bead rolled or ground flush as agreed on WLD and HCW product
For TP316 the usual choice is annealed and pickled for process pipe, with bright annealed or polished finishes for hygienic and pharmaceutical lines. Passivation after pickling or polishing can be added when the end-user specification calls for it, even though SA-312 itself does not require it. If the project bans chloride-bearing marking inks, say so on the order; otherwise the mill will apply its normal stencil practice and ship its default AP finish.
Inspection and Testing
The base acceptance package for SA-312 TP316 pipe combines chemistry, tensile testing, heat-treatment evidence, and a pressure or electrical integrity test on every length. The items below make up the usual package; supplementary requirements and project corrosion tests only apply when they are written on the purchase order.
- Heat (melting) analysis — mandatory per heat against Table 1 for TP316: C ≤0.08%, Mn ≤2.00%, P ≤0.045%, S ≤0.030%, Si ≤1.00%, Cr 16.0–18.0%, Ni 10.0–14.0%, and Mo 2.00–3.00%
- Product analysis — when ordered (Suppl. S1 or PO wording), using A480 Table A1.1 tolerances via A999 §6.3
- Tension test — 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield minimum, with 35% longitudinal / 25% transverse elongation on a lot basis
- Flattening test — or the alternate bend test where the standard permits
- Hydrostatic or nondestructive electric test — every length; manufacturer’s option unless the order fixes the method
- Visual and dimensional check — against ordered NPS/schedule or OD × wall, with TP316 (UNS S31600) on every stencil
Mill test certificates: EN 10204 3.1 is the standard documentation from SHH STEEL supply. For TP316 the certificate must report the full Table 1 chemistry with Mo inside 2.00–3.00%, the 75/30 ksi tensile results and 35%/25% elongation, the hydro or NDE method, and the 1900 °F anneal. EN 10204 3.2 or third-party witness by SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency is arranged when specified, and it should be booked before final testing rather than after the heat has been released. Dual ASME SA-312 / ASTM A312 certification is available when chemistry, heat treatment, mechanical tests, and marking satisfy both editions named on the order.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms chemistry on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S8 minimum wall | Wall interpreted as minimum rather than nominal |
| S9 weld decay | Compares weld and base-metal loss rates |
Receiving review should confirm Mo 2.00–3.00%, Cr 16.0–18.0%, Ni 10.0–14.0%, carbon ≤0.08%, 75/30 ksi tensile, elongation, and the anneal statement. A handheld PMI gun will separate TP316 from TP304 easily on molybdenum, but it cannot measure carbon reliably, so TP316 and TP316L stock must be separated using the certificate and stencil rather than the gun.
Packaging and Shipping
Export and domestic shipments of SA312 TP316 pipe are packed for handling and for ocean or land transport. The packing we normally apply is summarized below, and anything beyond it can be agreed on the order.
- Seaworthy bundles — pipes strapped or cradled in bundles sized for container or break-bulk handling, with non-metallic separators where the finish needs protecting
- End caps — plastic or metal caps on plain or beveled ends to keep out damage and contamination in transit
- Marking — specification, grade (TP316 (UNS S31600)), heat number, size, manufacturing type (SML / WLD / HCW), test letters, and mill identity as SA-312 and the purchase order require
- Export protection — waterproof wrapping or desiccant as agreed for polished or bright-annealed finishes, with low-chloride inks on request
Segregate TP316 from ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 TP304 Stainless Steel Pipe, and ASME SA312 TP316H Stainless Steel Pipe on the packing list and in the yard, because they look identical. Use separate bundles and distinct tags on mixed shipments, and have receiving inspectors check stencil heat numbers against the MTC for every length. Keep interiors dry and capped so chloride-bearing moisture cannot stain or pit the surface before installation. Shipping documents normally include the packing list, invoice, bill of lading or air waybill, and the 3.1 or 3.2 MTC with full Table 1 chemistry, plus origin and customs papers to suit the agreed Incoterms.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless plate and pipe, and for SA312 TP316 we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 chemistry on the MTC with molybdenum shown inside the 2.00–3.00% band, together with the 75/30 ksi results and the 1900 °F anneal statement. Heat identity stays unbroken from the melt to the finished length, so receiving inspection can clear each heat against Table 1 and Table 4 without chasing paperwork after the pipe has arrived.
We check supplier certificates before shipment for molybdenum near the lower limit, missing anneal statements, or TP304 stock mislabelled as 316, so problems are caught at the mill rather than at the fabricator. Where you want TP316/TP316L dual marking, we confirm before the order that the heat will meet C ≤0.035% and the TP316 tensile floors together.
- Specification fidelity — chemistry and tensile to SA-312/A312 Table 1 and Table 4 for TP316; Mo 2.00–3.00% reported; 1900 °F anneal stated; heat number on every length
- Mill resources — SML, WLD, and HCW from qualified stainless pipe mills with heat traceability; cutting and beveling on confirmed orders
- Documentation — EN 10204 3.1 MTCs as standard with full Table 1 chemistry; 3.2 or third-party inspection on request
- Dual marking — ASME SA-312 and ASTM A312 when the heat and tests meet both editions you name
- Related grades — ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 TP316H Stainless Steel Pipe, ASME SA312 TP304 Stainless Steel Pipe, and ASME SA312 TP317L Stainless Steel Pipe when a project buys a matched package
- Export packing — seaworthy bundles, end protectors, and durable grade, heat, size, and type marking
Quotations follow your purchase-order language for edition year, manufacturing type, size, wall, finish, and any supplementary tests you name (S1, S5, S7, S8, S9). If the same project also needs plate or fittings, ask for coordinated heats so the chemistry lines up across product forms. Grade hub: ASME SA 312/SA 312M.
Supply Capability
SHH STEEL can supply ASME SA312 TP316 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.
| Item | SHH STEEL capability for TP316 |
|---|---|
| Standard | ASME SA-312/SA-312M and/or ASTM A312/A312M TP316 / UNS S31600 |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD/wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | SRL, DRL, or cut-to-length |
| Finish | Annealed and pickled; blasted and pickled; bright annealed or polished by agreement |
| Testing | Tension (75/30 ksi), flattening/bend, hydro or NDE per length; full Table 1 chemistry with Mo 2.00–3.00% on MTC; 1900 °F anneal stated; S1/S5/S7/S8/S9 on order |
| Documents | EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
Common TP316 schedules in welded and seamless form are frequently available from stock, and we check the stock certificate against Table 1 before offering it. Heavy-wall seamless, large welded sizes, and special walls are normally mill-order items. Enquiries should state the SA-312 edition, TP316 (UNS S31600), SML/WLD/HCW, NPS or OD × wall (and whether wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements, so mill slots line up with your need date. Cut lengths, beveling, and packing-list marking are available on confirmed orders, and grouping project sizes onto one heat keeps the chemistry consistent while helping meet mill minimums without over-ordering.
FAQ
-
Is ASME SA312 the same as ASTM A312 for TP316?
- For chemistry (Table 1), tensile requirements (Table 4), manufacturing types, and most testing language, ASME SA-312/SA-312M follows ASTM A312/A312M of the edition it references, so the grade rows for TP316 / UNS S31600 read the same. Dual SA-312/A312 marking is common and we supply it when the heat and the tests satisfy both editions named on the purchase order.
-
What is the UNS number for TP316?
- Table 1 lists TP316 as UNS S31600. Put both the grade name and the UNS number on the purchase order, the stencil, and the mill test certificate. Carrying the UNS through every document is the simplest way to stop the pipe being confused with a sister grade that looks identical in the yard and reads similarly on a handheld PMI gun.
-
Seamless vs welded TP316 — which should I order?
- Neither route is better in every case. Seamless is the usual choice for heavy walls, high pressure, and small bores where the owner prefers no longitudinal seam, while welded pipe is economical in thinner walls and larger diameters and is made without filler metal. Both must meet the same Table 1 chemistry, the same 75/30 ksi Table 4 floor, and the same solution anneal, so let the design code and the size range decide.
-
Hydrostatic test or NDE — which will my TP316 pipe get?
- Every length must pass either a hydrostatic test or a nondestructive electric test, and SA-312 leaves the choice to the manufacturer unless the purchase order fixes the method. If your inspection plan or the owner’s specification needs a hydrotest on every length, or a particular eddy-current or ultrasonic practice, write it on the order so the mill plans for it before production starts.
-
Does SA-312 Table 4 set a hardness limit for TP316?
- No. Table 4 gives the tensile strength, yield strength, and elongation minima for TP316, but it does not list a hardness maximum. Catalogue Brinell or Rockwell figures you may see elsewhere are typical values, not specification requirements. If hardness matters for your fabrication or for the end user, state the limit on the purchase order and we will make sure it is tested and reported on the certificate.
-
What filler metal should I use to weld TP316 pipe?
- SA-312 Table 6 lists ER316 (UNS S31680 / W31640) as the recommended filler for TP316 when filler is used on mill seam repairs. For field girth welds, ER316 or ER316L is the normal choice, with ER316L preferred where joints stay as-welded in corrosive service. Record the agreed AWS classification on the WPS and PQR, and remember that mill longitudinal seams are made without filler.
-
What wall-thickness tolerance applies to TP316 pipe?
- Wall tolerance follows SA-312 Table 3: 12.5% under for every size band, with the over-tolerance ranging from 15.0% to 22.5% depending on NPS, t/D ratio, and whether the pipe is seamless or welded. If your design is based on minimum wall rather than nominal wall, order Supplementary Requirement S8 so the mill rolls to the right target from the start.
-
Which sister grades do buyers compare with TP316?
- Buyers most often compare TP316 with ASME SA312 TP316L Stainless Steel Pipe for as-welded corrosion, ASME SA312 TP316H Stainless Steel Pipe for creep-range service, ASME SA312 TP304 Stainless Steel Pipe when molybdenum is not needed, and ASME SA312 TP317L Stainless Steel Pipe when chlorides are higher than TP316 can comfortably handle. Each has its own Table 1 and Table 4 rows, so do not substitute one for another without checking the design basis and the code allowables.
-
TP316 vs TP316L — which should I order?
- TP316 allows carbon up to 0.08% and carries 75/30 ksi floors, while TP316L limits carbon to 0.035% with 70/25 ksi. Choose TP316L when welds stay as-welded in corrosive service, and TP316 when strength matters and welds are annealed. Many mills supply dual TP316/TP316L heats that meet the low carbon and the higher tensile floors together, which covers both specifications.
-
TP316 vs TP304 — what does the molybdenum buy me?
- TP316 adds a mandatory 2.00–3.00% molybdenum and raises nickel to 10.0–14.0%, while chromium drops slightly to 16.0–18.0%. The tensile floors are the same 75/30 ksi. The practical gain is much better resistance to pitting and crevice corrosion in chloride-bearing water and many chemicals, so TP316 is the usual upgrade when TP304 has pitted in service.
-
What heat treatment does SA-312 require for TP316?
- TP316 falls under the Table 2 default for grades not individually listed: solution anneal at 1900 °F [1040 °C] minimum, then water quench or another rapid cool that prevents carbide reprecipitation. Delivery is always the annealed condition, including HCW pipe, and the certificate should state the anneal temperature and cooling method so receiving inspection can confirm compliance.
-
What product-analysis limits apply to TP316?
- Product analysis applies only when ordered through Supplementary Requirement S1 or purchase-order wording. A480 Table A1.1 tolerances, brought in through A999 §6.3, widen the Table 1 limits to C ≤0.09%, Mn ≤2.04%, Si ≤1.05%, Cr 15.80–18.20%, Ni 9.90–14.15%, and Mo 1.95–3.10%. These are acceptance limits for finished pipe, not melt targets.
Conclusion
ASME SA312 TP316 / UNS S31600 is the standard molybdenum-bearing austenitic pipe grade, with C ≤0.08%, Cr 16.0–18.0%, Ni 10.0–14.0%, and Mo 2.00–3.00%, a 75/30 ksi Table 4 floor with 35% L / 25% T elongation, a 1900 °F [1040 °C] solution anneal, and ER316 filler from Table 6. It is the usual step up from ASME SA312 TP304 Stainless Steel Pipe when chlorides are present, and it can be dual certified with ASME SA312 TP316L Stainless Steel Pipe when one heat meets both rows. Order the manufacturing type, size and wall, finish, any dual marking, and supplementary tests explicitly so the certificate matches your specification. For stock checks, mill certificates, or dual SA-312/A312 supply questions, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category on steelspecs.com.