ASME SA312 UNS S30600 Stainless Steel Pipe | ASME SA312 Stainless Steel - SHH STEEL

ASME SA312 UNS S30600 Stainless Steel Pipe | SA 312/SA 312M

ASME SA312 UNS S30600 high-silicon austenitic stainless steel pipe to SA-312/SA-312M (ASTM A312/A312M), no TP designation, for hot concentrated sulfuric acid service: SML, WLD and HCW with Si 3.7–4.3%, C ≤0.018%, 78/35 ksi minima and a 2010–2140 °F anneal, supplied by SHH STEEL with EN 10204 3.1 MTCs.
Grade
UNS S30600
Standard
ASME SA312 / SA 312M (ASTM A312 / A312M)
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASME SA312 UNS S30600 Stainless Steel Pipe

ASME SA-312/SA-312M (identical in its grade tables to ASTM A312/A312M) covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe for high-temperature and general corrosive service. UNS S30600 sits in Table 1 with no TP designation—the grade column shows only an ellipsis—so the pipe is ordered, stencilled, and certified by its UNS number alone. Do not let a trade name or a loose “high-silicon 304” description stand in for it on a purchase order, because the Code row is what the inspector will check the heat against.

The chemistry is unusual and deliberate: silicon 3.7–4.3%, chromium 17.0–18.5%, nickel 14.0–15.5%, carbon no more than 0.018%, phosphorus and sulfur each ≤0.02%, manganese ≤2.00%, with molybdenum (≤0.20%) and copper (≤0.50%) held to residual levels. Table 4 sets minima of 78 ksi [540 MPa] tensile and 35 ksi [240 MPa] yield with 35% longitudinal / 25% transverse elongation, and Table 2 lists S30600 on its own with a 2010–2140 °F [1100–1170 °C] solution-treatment range rather than the 1900 °F default. S30600 is not listed in Table 6, so no AWS filler class is named and filler is by agreement. It is not an H grade.

The reason for all that silicon is hot, concentrated sulfuric acid and similar strongly oxidizing acids. As sulfuric acid gets stronger and hotter it behaves more like an oxidizing medium, and ordinary 304L or 316L lose passivity and corrode at rates that make them impractical. Around 4% silicon gives a silicon-enriched passive film that stays stable in that regime, the ultra-low carbon keeps grain-boundary carbides out of the picture, and the higher nickel keeps the alloy fully austenitic and ductile enough to make and weld into pipe. Cast high-silicon irons resist the same acid but are brittle; S30600 is the wrought, weldable route.

SHH STEEL can supply ASME SA312 UNS S30600 stainless steel pipe to the edition named on the enquiry, as seamless (SML), welded (WLD), or heavily cold-worked (HCW) pipe; in ASME B36.19 schedules with special OD and wall by agreement; with EN 10204 3.1 mill test certificates that report the full Table 1 window, including silicon, carbon, and the Mo and Cu residuals, plus the actual anneal temperature against the 2010–2140 °F range; and with dual SA-312/A312 marking when the heat, heat treatment, tests, and marking satisfy both editions on the order. Because only a few mills make high-silicon pipe, we confirm size range and lead time before quoting.

Names you will meet in enquiries and how they map to the ordered product:

  • ASME SA312 UNS S30600 / SA-312 S30600 — correct Code form; no TP name exists
  • ASTM A312 UNS S30600 — the ASTM parent, with the same chemistry and tensile rows
  • EN 1.4361 (X1CrNiSi18-15-4) — commonly cited European counterpart; verify in the EN standard before accepting it as equivalent
  • Producer trade names — the chemistry has been sold under proprietary names; still order and certify by UNS S30600

S30600 is not a drop-in for its sister grades. ASME SA312 UNS S30601 Stainless Steel Pipe pushes silicon to 5.0–5.6% with 17.0–18.0% nickel, carbon ≤0.015%, and a 37 ksi yield floor for the most aggressive acid conditions. ASME SA312 UNS S30615 Stainless Steel Pipe also carries a lot of silicon but pairs it with high carbon (0.16–0.24%) and aluminium for hot carburizing gases—the opposite design intent. And ASME SA312 TP304L Stainless Steel Pipe or ASME SA312 TP316L Stainless Steel Pipe remain the economical choice for ordinary chemical service where oxidizing sulfuric acid is not the problem. Family hub: ASME SA 312/SA 312M.

Manufacturing Types (SML / WLD / HCW)

ASME SA-312 recognizes three manufacturing routes for UNS S30600 pipe, and the route is a purchase-order decision driven by the design code, the size range, wall thickness, and how the owner wants the pipe inspected. The route never changes the chemistry: whichever way the pipe is made, the heat must still meet the Table 1 window of Si 3.7–4.3%, C ≤0.018%, Cr 17.0–18.5%, and Ni 14.0–15.5%, and every length must still go through the solution anneal at the Table 2 range of 2010–2140 °F [1100–1170 °C] before it is released.

  • Seamless (SML) — no welding at any stage. Preferred for high-pressure service, thick walls, and owners who exclude welded pipe from the design class. High silicon raises hot strength and narrows the hot-working window, so seamless S30600 is a made-to-order specialty in limited sizes.
  • Welded (WLD) — automatic welding without filler metal, with the weld finished so the pipe meets dimensional and mechanical requirements after the final heat treatment. The strip or plate heat must itself carry the full UNS S30600 chemistry, so ask for the coil or plate heat number on the certificate.
  • Heavily cold-worked (HCW) — welded pipe cold worked to at least 35% reduction of wall and weld before the final anneal, again without filler in the longitudinal seam, with the weld radiographed before cold work. Order HCW when the project specifically wants that marking and the process controls SA-312 writes around it.

Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test in place of the hydrotest, and lots for mechanical testing follow clause 11.1. Because the alloy is bought for acid service where a leak is serious, buyers commonly add product analysis (S1) and radiography of welded seams (S5).

For acid-plant piping in medium and large diameters, welded pipe from S30600 plate is the usual product, with seamless reserved for smaller bores. Production is limited to a small number of mills with high-silicon experience, so expect longer lead times, minimum quantities, and fewer size options than for ASME SA312 TP304L Stainless Steel Pipe. The high anneal temperature also means the mill has to control its furnace closely; ask for the actual anneal temperature on the MTC so you can confirm the 2010–2140 °F window was met rather than assuming a 1900 °F habit carried over from commodity grades.

Chemical Composition of SA312 UNS S30600

Each heat must meet the Table 1 melting analysis. Product analysis (S1) is evaluated with ASTM A480/A480M Table A1.1 tolerances via A999, with one gap noted below.

Melting analysis (heat / ladle analysis) — Table 1

Heat analysis for UNS S30600. Values are maximum unless a range is shown; ellipses (…) mean no requirement.

Element UNS S30600 melting analysis
Carbon (C) ≤ 0.018
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.02
Sulfur (S) ≤ 0.02
Silicon (Si) 3.7 – 4.3
Chromium (Cr) 17.0 – 18.5
Nickel (Ni) 14.0 – 15.5
Molybdenum (Mo) ≤ 0.20
Copper (Cu) ≤ 0.50
Nitrogen (N) … (no requirement)

Source: ASME SA-312/SA-312M ≡ ASTM A312/A312M Table 1, UNS S30600 (grade column “…”). Elements shown “…” have no requirement and need not be determined (footnote B).

Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.018 0.005 over ≤ 0.023
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.02 0.005 over ≤ 0.025
Sulfur (S) ≤ 0.02 0.005 over ≤ 0.025
Silicon (Si) 3.7 – 4.3 0.15 under / over 3.55 – 4.45
Chromium (Cr) 17.0 – 18.5 0.20 under / over 16.80 – 18.70
Nickel (Ni) 14.0 – 15.5 0.15 under / over 13.85 – 15.65
Molybdenum (Mo) ≤ 0.20 No A480 row for ≤0.20% (rows start over 0.20) Not established—by agreement
Copper (Cu) ≤ 0.50 0.03 over ≤ 0.53

Molybdenum gap: A480 Table A1.1 lists molybdenum tolerances only for limits “over 0.20%”. A maximum of exactly 0.20% has no tolerance row, so product-analysis acceptance for Mo is by agreement. SHH STEEL reports the heat value and does not apply an invented tolerance.

Silicon tolerance: both ends of the 3.7–4.3% range fall in the A480 “over 3.00 to 6.00” row, so 0.15 applies each way. Nickel 14.0–15.5% is entirely in the 10–20% row (0.15). The carbon maximum of 0.018% is in the “over 0.010 to 0.030” row (0.005).

Why each element is controlled:

  • Silicon 3.7–4.3% — the active ingredient for oxidizing-acid resistance
  • Carbon ≤0.018% — eliminates carbide precipitation that would be attacked in acid
  • Nickel 14.0–15.5% — offsets the ferrite-forming effect of silicon and keeps the alloy austenitic
  • Chromium 17.0–18.5% — base passivity
  • P and S ≤0.02% — tight limits improve hot workability and weldability of the high-Si alloy
  • Mo ≤0.20%, Cu ≤0.50% — kept as residuals; in strongly oxidizing acids these elements can be detrimental

Mechanical Properties of SA312 UNS S30600

Property (SA-312 Table 4) UNS S30600
Tensile strength, min 78 ksi [540 MPa]
Yield strength (0.2% offset), min 35 ksi [240 MPa]
Elongation in 2 in. or 50 mm (or 4D), min 35% longitudinal / 25% transverse
Hardness No maximum listed in Table 4

Silicon contributes solid-solution strengthening, so S30600 meets higher minima than TP304L (70/25 ksi) despite its very low carbon. The elongation requirement is the same all-grades value as for 304, confirming that the alloy remains ductile when correctly annealed.

Grade UNS Tensile min, ksi [MPa] Yield min, ksi [MPa]
TP304L S30403 70 [485] 25 [170]
TP304 S30400 75 [515] 30 [205]
— S30600 78 [540] 35 [240]
— S30601 78 [540] 37 [255]

For pressure design, use allowable stresses for S30600 from the governing code where listed. Acid plant piping is often designed with generous corrosion allowances, and the mechanical design is rarely the limiting factor; the chemistry is. Tests are per SA-312: tension per lot, flattening or bend on 5% of pipes, hydro or NDE on each length. Hardness, impact, or elevated-temperature tests are PO options. Forming: S30600 is less ductile in hot working than 304 and somewhat harder to cold form. Fabricators bending pipe should use generous radii and trial bends.

Dimensions and Tolerances

S30600 pipe is made to ASME B36.19 sizes (Sch 5S, 10S, 40S, 80S) and to special OD/wall by agreement. Acid plants frequently use heavier walls than strictly needed for pressure, to provide a corrosion allowance.

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%

Source: SA-312 Table 3; outside diameter variations per A999/A999M.

  • Lengths: NPS 1/8 to 8 up to 24 ft (15–24 ft range) unless agreed; cut lengths no more than 1/4 in. [6 mm] over
  • Jointers: not permitted unless specified
  • Ends: plain or beveled; flanged spools are typically fabricated after delivery

Typical acid-plant line sizes run from NPS 1 to NPS 24 and larger. Small sizes may be seamless; larger sizes are usually welded from S30600 plate with full radiography. Flanges, fittings, and valves in the same alloy are separate procurement items under their own product specifications, and their availability often dictates the system design. Because few mills produce S30600, available sizes may not cover every NPS and schedule. Confirm at enquiry; welded pipe from plate can fill gaps in larger sizes.

When ordering, state the corrosion allowance basis in internal documents rather than on the PO; the PO should give nominal or minimum wall, and S8 if minimum wall is required.

Equivalent Grades

Designation Relationship to S30600
ASME SA-312 / ASTM A312, UNS S30600 Governing pipe grade (no TP name)
ASME SA-240 / A240 S30600 Plate counterpart (separate specification)
EN 1.4361 Commonly cited European high-silicon austenitic; verify in EN standard
UNS S30601 Higher-Si sister (5.0–5.6% Si, 17.0–18.0% Ni); not interchangeable without review
Proprietary names Order by UNS S30600, not trade name

S30600 should not be confused with S30615 (another high-silicon grade in Table 1, but with high carbon and aluminium for heat resistance rather than acid service) or with conventional 304-type grades. See ASME SA312 UNS S30601 Stainless Steel Pipe, ASME SA312 UNS S30615 Stainless Steel Pipe, ASME SA312 TP304L Stainless Steel Pipe, ASME SA312 TP316L Stainless Steel Pipe.

Alternatives in concentrated sulfuric acid service, depending on concentration and temperature, include high-silicon cast irons, nickel alloys, and other proprietary high-Si stainless steels; selection belongs to a corrosion specialist.

Heat Treatment and Delivery Condition

SA-312 Table 2 lists S30600 individually:

Grade Solution treatment temperature Cooling
UNS S30600 2010–2140 °F [1100–1170 °C] Water quench or rapid cooling (Table 2 note D)

The higher, ranged temperature dissolves silicon-rich phases and produces a homogeneous austenitic structure. Annealing at the 1900 °F level used for 304 would not be sufficient for this alloy and would not comply with Table 2.

Under ASME clause 6.2, S30600 is not among the grades requiring reheat (H grades, S33228, S30815, S31272), so seamless pipe may be quenched directly after hot forming if it is at or above 2010 °F [1100 °C].

  • Delivered solution annealed within 2010–2140 °F and rapidly cooled
  • Pickled or blasted and pickled, free of scale and exogenous iron
  • Passivation on request
  • After fabrication welding, re-annealing is not normally required, but follow the alloy producer’s and corrosion engineer’s guidance for severe acid service

Ask for the actual anneal temperature to be recorded on the MTC. Because the window is ranged, both under- and over-temperature anneals are non-conforming.

Corrosion Resistance

S30600’s reason for existence is resistance in strongly oxidizing acid media, especially hot concentrated sulfuric acid. General industry and producer guidance describes it as suitable in sulfuric acid at high concentrations and elevated temperatures where 304L and 316L lose passivity, and in nitric acid and nitric–sulfuric mixtures. The silicon-rich passive film is the key.

  • Concentrated sulfuric acid: the main application; performance depends strongly on concentration, temperature, velocity, and impurities
  • Dilute sulfuric acid: less oxidizing; high-Si austenitics are not necessarily better than Mo- or Cu-bearing alloys there
  • Nitric acid: good resistance; low carbon prevents intergranular attack
  • Chlorides: no Mo; not intended for chloride service
  • Reducing acids (HCl, HF): not suitable

Temperature and concentration windows: acid plant designers usually map candidate materials against concentration–temperature charts from producers and corrosion handbooks. S30600 is positioned for the strong acid end of those charts, while dilute and intermediate concentrations are often better served by other alloys. Impurities such as chlorides, fluorides, or dissolved metals can shift the boundaries. Coupon testing in actual plant acid remains the best validation.

Anodic protection: some sulfuric acid coolers and piping systems use anodic protection to hold stainless steel in its passive range. The interaction between such systems and high-silicon alloys is a design matter for the licensor and is not covered by SA-312.

Velocity and turbulence matter: in acid coolers and pump discharge lines, erosion-corrosion can be the life-limiting mechanism. Design guidelines from acid plant licensors and the alloy producers should be followed. Corrosion data for S30600 are not part of SA-312. All performance statements above are general guidance; a corrosion specialist should confirm suitability for each service.

Applications of SA312 UNS S30600 Pipe

Application Role of S30600 Note
Sulfuric acid plants Acid circulation lines, distributor piping, absorption tower connections Follow licensor guidance on velocity
Acid coolers and heat exchangers Connection piping and headers Anodic protection used in some designs
Nitric acid production Process lines in oxidizing environments Low C prevents intergranular attack
Mixed acid service Nitric–sulfuric mixtures in chemical synthesis Confirm with corrosion testing
Oleum and acid storage transfer Transfer lines where cast iron is impractical Check temperature limits
Metallurgical acid plants Acid from smelter off-gas recovery Impurities (fluorides, chlorides) affect life

In all of these applications S30600 is usually one material among several in the same plant: carbon steel for strong acid storage at ambient temperature, ductile iron or alloy for pumps, and specialty stainless for the hottest, most oxidizing streams. The pipe is selected for the lines where its silicon-based passivity gives the best life-cycle cost.

For conventional chemical service, ASME SA312 TP304L Stainless Steel Pipe or ASME SA312 TP316L Stainless Steel Pipe is more economical. For even higher silicon, see ASME SA312 UNS S30601 Stainless Steel Pipe.

Weldability

S30600 can be welded by GTAW, GMAW, and SMAW, but it needs more care than 304L because high silicon increases solidification-cracking sensitivity. Filler metal and Table 6: UNS S30600 is not listed in SA-312 Table 6, so the specification names no AWS A5.9 classification. Filler selection is by agreement and must be qualified and recorded on the WPS; seam repairs under clause 15 must identify the filler on the certificate. In practice fabricators use matching high-silicon consumables offered by the alloy producers so that weld metal resists the same acid. A conventional 308L or 316L filler would leave the weld as the weak point in acid service.

  • Heat input: low to moderate; avoid wide weaves and high interpass temperatures
  • Hot cracking: high Si and the fully austenitic structure raise risk; follow producer procedures
  • Cleanliness: remove all contaminants; sulfur and phosphorus pickup must be avoided
  • Post-weld cleaning: pickle to remove heat tint, which is more readily attacked in acid

Weld joint design: full-penetration butt welds with smooth root profiles are preferred; crevices from incomplete penetration or backing rings can concentrate acid and cause local attack. Socket welds are generally avoided in severe acid service. Purge the root with argon and inspect it visually or by borescope where access allows. Qualify procedures to ASME Section IX on S30600 base metal, and consider corrosion testing of weld coupons in the actual acid when the service is critical.

Surface Finishes

Surface condition for UNS S30600 pipe should be stated on the purchase order rather than left to mill default. For stainless pipe, embedded free iron, residual scale, and chloride-bearing residues are where corrosion starts, so the finish is part of the material performance and not just appearance. The finishes we regularly quote for this grade are listed below.

  • Annealed and pickled (AP) — solution annealed at 2010–2140 °F [1100–1170 °C], then descaled in acid pickle or an equivalent process to a matte grey finish; the standard choice for process pipe
  • Blasted and pickled — common on heavy-wall seamless where blasting first makes scale removal more reliable
  • Bright annealed (BA) — annealed in a protective atmosphere where mill capability exists for the size; the anneal temperature still has to meet the Table 2 practice for UNS S30600
  • Mechanically polished — OD and/or ID polish to an agreed grit or Ra when ordered; polishing never replaces the solution anneal
  • Bead-finished welded OD — weld bead rolled or ground flush as agreed on WLD and HCW product

For acid service the annealed-and-pickled finish is the one to specify. Mills adjust pickling for the silicon-rich scale formed at the high anneal temperature, and any residual scale or heat tint is where attack starts in service, so check the bore of welded pipe on receipt and pickle and passivate site welds and heat-affected zones after fabrication. Passivation after pickling or polishing can be added when the end-user specification calls for it, even though SA-312 itself does not require it. If the project bans chloride-bearing marking inks, say so on the order; otherwise the mill will apply its normal stencil practice and ship its default AP finish.

Inspection and Testing

The base acceptance package for SA-312 UNS S30600 pipe combines chemistry, tensile testing, heat-treatment evidence, and a pressure or electrical integrity test on every length. The items below make up the usual package; supplementary requirements and project corrosion tests only apply when they are written on the purchase order.

  • Heat (melting) analysis — mandatory per heat against Table 1 for UNS S30600: Si 3.7–4.3%, C ≤0.018%, P and S ≤0.02%, Cr 17.0–18.5%, Ni 14.0–15.5%, Mo ≤0.20%, Cu ≤0.50%
  • Product analysis — when ordered (Suppl. S1 or PO wording), using A480 Table A1.1 tolerances via A999 §6.3; note that A480 has no tolerance row for Mo at ≤0.20%, so Mo product acceptance is by agreement
  • Tension test — 78 ksi [540 MPa] tensile, 35 ksi [240 MPa] yield, 35% L / 25% T elongation on a lot basis
  • Flattening test — or the alternate bend test where the standard permits
  • Hydrostatic or nondestructive electric test — every length; manufacturer’s option unless the order fixes the method
  • Visual and dimensional check — against ordered NPS/schedule or OD × wall, with “UNS S30600” on every stencil

Mill test certificates: EN 10204 3.1 is the standard documentation from SHH STEEL supply. For S30600 the certificate should show silicon inside 3.7–4.3%, carbon ≤0.018%, the Mo and Cu residuals as reported values, and the actual solution-anneal temperature inside 2010–2140 °F; a certificate missing silicon or the anneal temperature is a reason to hold the shipment until it is corrected. EN 10204 3.2 or third-party witness by SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency is arranged when specified, and it should be booked before final testing rather than after the heat has been released. Dual ASME SA-312 / ASTM A312 certification is available when chemistry, heat treatment, mechanical tests, and marking satisfy both editions named on the order.

Option Purpose
S1 product analysis Confirms chemistry on finished pipe
S5 radiography Weld integrity on WLD pipe
S7 intergranular corrosion A262 Practice E after sensitizing treatment
S8 minimum wall Wall interpreted as minimum rather than nominal
S9 weld decay Compares weld and base-metal loss rates

On receipt, PMI is a sensible check because S30600 looks like any other stainless pipe and a mix-up with 304L in an acid plant would be serious. XRF confirms silicon, chromium, and nickel approximately, but carbon at the 0.018% level needs OES or laboratory analysis. Where the service is critical, owners also corrosion-test weld coupons in the actual acid before releasing the fabrication procedure.

Packaging and Shipping

Export and domestic shipments of UNS S30600 pipe are packed for handling and for ocean or land transport. The packing we normally apply is summarized below, and anything beyond it can be agreed on the order.

  • Seaworthy bundles — pipes strapped or cradled in bundles sized for container or break-bulk handling, with non-metallic separators where the finish needs protecting
  • End caps — plastic or metal caps on plain or beveled ends to keep out damage and contamination in transit
  • Marking — specification, grade (UNS S30600), heat number, size, manufacturing type (SML / WLD / HCW), test letters, and mill identity as SA-312 and the purchase order require
  • Export protection — waterproof wrapping or desiccant as agreed for polished or bright-annealed finishes, with low-chloride inks on request

Because the stencil shows only the UNS number, keep S30600 bundles physically segregated from 304L and 316L at every handling point, and brief receiving inspectors that the grade has no TP name. Acid-plant owners often ask for desiccant inside sealed wrap and plugged ends for sea shipments; put that on the PO so the mill packs accordingly. Keep interiors dry and capped so chloride-bearing moisture cannot stain or pit the surface before installation. Shipping documents normally include the packing list, invoice, bill of lading or air waybill, and the 3.1 or 3.2 MTC with full Table 1 chemistry, plus origin and customs papers to suit the agreed Incoterms.

Why Choose SHH STEEL

SHH STEEL supplies specification-driven stainless plate and pipe, and for ASME SA312 UNS S30600 / S30600 we quote against the edition you name rather than a generic catalogue sheet. High-silicon acid-service pipe is a niche product, and the commercial risk is usually not price but getting a heat that is certified to the wrong row, annealed at the wrong temperature, or welded with the wrong filler. We source S30600 from mills with real high-silicon production experience and check the certificate against Table 1, Table 2, and Table 4 before the pipe leaves. Heat identity stays unbroken from the melt to the finished length, so receiving inspection can clear each heat against Table 1 and Table 4 without chasing paperwork after the pipe has arrived.

We are also honest about the gaps the standard leaves. SA-312 gives no Table 6 filler class for S30600 and A480 gives no product-analysis tolerance for molybdenum at ≤0.20%, so both are handled by agreement and written into the order rather than papered over. If an enquiry really describes dilute or chloride-bearing service, we will say so and point toward TP316L or another grade rather than sell a high-silicon alloy into a job it was not designed for.

  • Specification fidelity — certified as UNS S30600 with all Table 1 elements reported, Si and C checked first, and the actual 2010–2140 °F anneal temperature on the MTC
  • Mill resources — SML, WLD, and HCW from qualified stainless pipe mills with heat traceability; cutting and beveling on confirmed orders
  • Documentation — EN 10204 3.1 MTCs as standard with full Table 1 chemistry; 3.2 or third-party inspection on request
  • Dual marking — ASME SA-312 and ASTM A312 when the heat and tests meet both editions you name
  • Related grades — UNS S30601, TP304L, and TP316L when a project buys a matched package
  • Export packing — seaworthy bundles, end protectors, and durable grade, heat, size, and type marking

Quotations follow your purchase-order language for edition year, manufacturing type, size, wall, finish, and any supplementary tests you name (S1, S5, S7, S8, S9). If the same project also needs plate or fittings, ask for coordinated heats so the chemistry lines up across product forms. Grade hub: ASME SA 312/SA 312M.

Supply Capability

SHH STEEL can supply ASME SA312 UNS S30600 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.

Item SHH STEEL capability for UNS S30600
Standard ASME SA-312/SA-312M and/or ASTM A312/A312M (edition per PO; grade marked UNS S30600, no TP name)
Manufacturing types SML, WLD, HCW
Size NPS 1/8 and up per ASME B36.19; special OD/wall by agreement
Schedules 5S, 10S, 40S, 80S and non-standard walls
Length SRL, DRL, or cut-to-length
Finish Annealed and pickled; blasted and pickled; bright annealed or polished by agreement
Testing Hydrostatic or NDE per length; S1 product analysis, S5 radiography, PMI, and weld-coupon acid tests when ordered
Documents EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

S30600 is a made-to-order grade with limited producers rather than a stock item, although remnant lengths from earlier heats sometimes cover small urgent lots. Share sizes, walls, quantities, route, and a short description of the acid service early so the mill can confirm feasibility and lead time before your project schedule is fixed. Enquiries should state the SA-312 edition, UNS S30600 (no TP name), SML/WLD/HCW, NPS or OD × wall (and whether wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements, so mill slots line up with your need date. Cut lengths, beveling, and packing-list marking are available on confirmed orders, and grouping project sizes onto one heat keeps the chemistry consistent while helping meet mill minimums without over-ordering.

FAQ

Does UNS S30600 have a TP grade name in SA-312?
No. Table 1 lists UNS S30600 with an ellipsis in the grade column, so there is no TP designation to quote. Order, mark, and certify the pipe as “ASME SA-312 UNS S30600” (or ASTM A312 UNS S30600) with the edition year, and reject certificates that describe it only as a trade name or as a modified 304.
What is ASME SA312 UNS S30600 pipe mainly used for?
It is chosen for hot, concentrated sulfuric acid and other strongly oxidizing acid streams, typically in sulfuric acid plants, where 304L and 316L lose passivity. The 3.7–4.3% silicon forms a stable silicon-enriched passive film, and ultra-low carbon keeps grain-boundary carbides from becoming attack paths. Confirm the actual concentration and temperature window with the licensor or producer.
What Table 1 chemistry defines UNS S30600?
Table 1 requires C ≤0.018%, Mn ≤2.00%, P ≤0.02%, S ≤0.02%, Si 3.7–4.3%, Cr 17.0–18.5%, Ni 14.0–15.5%, Mo ≤0.20%, and Cu ≤0.50%, with no nitrogen requirement. These are melting-analysis limits; if you need the finished pipe checked as well, order product analysis (S1) explicitly on the purchase order.
What are the Table 4 mechanical requirements for S30600?
Table 4 sets 78 ksi [540 MPa] minimum tensile strength and 35 ksi [240 MPa] minimum yield strength, with 35% longitudinal and 25% transverse elongation, and no hardness maximum. Those floors sit above TP304L (70/25 ksi) thanks to silicon strengthening. Design to the governing code allowables; in acid plants the corrosion allowance usually drives wall thickness more than stress does.
What solution anneal does Table 2 require for S30600?
Table 2 lists S30600 individually at 2010–2140 °F [1100–1170 °C] followed by rapid cooling—a ranged temperature well above the 1900 °F default used for many 300-series grades. Below the range the anneal does not comply; above it, grain growth becomes a risk. Ask for the actual anneal temperature on the MTC so you can verify it.
Which filler metal should be used to weld S30600 pipe?
SA-312 Table 6 does not list S30600, so no AWS A5.9 class is specified and filler is by agreement, frozen on the WPS and PQR. Fabricators normally use matching high-silicon consumables from the alloy producers; a 308L or 316L wire would leave the weld as the weak point in acid service. The mill longitudinal seam itself is autogenous.
How does UNS S30600 differ from UNS S30601?
S30601 is the higher-silicon sister: Si 5.0–5.6% versus 3.7–4.3%, Ni 17.0–18.0% versus 14.0–15.5%, C ≤0.015% versus ≤0.018%, a controlled Mn window of 0.50–0.80%, and a 37 ksi yield floor instead of 35 ksi. S30601 targets the most aggressive acid end; S30600 is easier to fabricate. Neither substitutes for the other without engineering review.
Is UNS S30600 related to the high-silicon grade UNS S30615?
Only by the silicon number. S30615 combines Si 3.2–4.0% with high carbon (0.16–0.24%) and aluminium 0.80–1.50% for hot carburizing and oxidizing gases, and has 90/40 ksi Table 4 floors. S30600 is ultra-low carbon for oxidizing acid. Putting one where the other is specified would be a serious material error, so always check the UNS number on the stencil.
Is there a product-analysis tolerance for molybdenum in S30600?
Not one that A480 Table A1.1 establishes. Its molybdenum rows start at limits “over 0.20%”, so a maximum of exactly 0.20% has no tolerance row. Product-analysis acceptance for Mo is therefore by agreement. We report the heat value and do not apply an invented tolerance; if your inspector needs a number, write it on the PO.
Can UNS S30600 be used in chloride or dilute acid service?
It is not designed for that. S30600 carries essentially no molybdenum, and in dilute, reducing, or chloride-bearing acids molybdenum is what gives stainless steel its resistance, which is why TP316L outperforms it there. Choose S30600 for strong oxidizing acid; for chloride pitting duty look at TP316L or a molybdenum-rich superaustenitic grade instead.
Can S30600 be supplied as seamless pipe?
Yes, SA-312 permits seamless, welded, and heavily cold-worked S30600, and all routes must meet the same Table 1 chemistry and the 2010–2140 °F anneal. In practice seamless is a made-to-order product in smaller sizes, because high silicon narrows the hot-working window, while welded pipe from S30600 plate is the common form for medium and large acid-plant lines.
Can you dual-certify UNS S30600 to SA-312 and A312?
Yes, when the heat analysis, the solution anneal inside 2010–2140 °F, the tension and flattening tests, and the marking meet both editions named on the order. State the ASME and ASTM edition years on the purchase order and require the MTC to reference both, so receiving inspection can clear the heat without a second paperwork round after shipment.

Conclusion

ASME SA312 UNS S30600 is the TP-less high-silicon austenitic pipe grade for hot, concentrated sulfuric acid and other strongly oxidizing acids: Si 3.7–4.3%, C ≤0.018%, Cr 17.0–18.5%, Ni 14.0–15.5%, Mo and Cu held as residuals, 78 ksi [540 MPa] tensile and 35 ksi [240 MPa] yield minima, and a Table 2 solution anneal of 2010–2140 °F [1100–1170 °C]. It is not a substitute for UNS S30601, UNS S30615, or TP316L, and the standard leaves filler selection and Mo product tolerance to agreement, so put those on the order. For sizes, lead times, mill certificates, or dual SA-312/A312 supply, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X