ASME SA312 UNS S31254 Stainless Steel Pipe | SA 312/SA 312M
What is ASME SA312 UNS S31254 Stainless Steel Pipe
ASME SA-312/SA-312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. UNS S31254 appears in Table 1 with no TP designation—the grade column shows only an ellipsis—so the pipe is ordered, marked, and certified by UNS number alone. It is the classic 6Mo super-austenitic member of the SA-312 family: carbon ≤0.020%, manganese ≤1.00%, phosphorus ≤0.030%, sulfur ≤0.010%, silicon ≤0.80%, chromium 19.5–20.5%, nickel 17.5–18.5%, molybdenum 6.0–6.5%, nitrogen 0.18–0.25%, and copper 0.50–1.00%. Commercially the same product may be labelled 254 SMO®-type, 6Mo, or EN 1.4547 pipe, but those nicknames are not SA-312 grade names. For pressure piping and code work, cite UNS S31254 and the edition of SA-312 or A312 on the purchase order and on the mill test certificate—do not rely on a bare “254 SMO” market label.
The intentional ~6% molybdenum plus nitrogen pushes pitting resistance (PREN typically ~42–45 using specification minima—calculated commentary, not a Table 1 value) into the same class as many super-duplex grades, while remaining fully austenitic—tough at low temperature, non-magnetic, and free of duplex 475 °C embrittlement limits. Table 4 tensile requirements are thickness-dependent: 98 ksi [675 MPa] / 45 ksi [310 MPa] for wall t ≤ 0.187 in. [5.00 mm], and 95 ksi [655 MPa] / 45 ksi [310 MPa] for thicker product. Elongation follows the general austenitic rule (35% longitudinal / 25% transverse)—S31254 is not in the S31050/S32615 special 25% group. Heat treatment follows Table 2 at 2100 °F [1150 °C] minimum (listed with S32654), higher than the 1900 °F default used for many 300-series grades. It is not an H grade: there is no carbon floor, no Table 5 grain-size rule, and no clause 6.2 reheat requirement. Table 6 lists no AWS filler class for S31254, so filler selection is by agreement on the WPS—industry often freezes overalloyed Ni-Cr-Mo consumables (ERNiCrMo-3 / -4 type practice). The primary service niche is warm seawater, chloride brines, and acidic chloride process streams where 316L and 904L pit or crevice; calling it “316L upgrade” or bare “6Mo” on a seawater PO without the UNS is a specification error.
SHH STEEL can supply ASME SA312 UNS S31254 stainless steel pipe to the edition named on the enquiry, including seamless (SML), welded (WLD), and heavily cold-worked (HCW) routes; ASME B36.19 schedules and special OD/wall by agreement; EN 10204 3.1 mill test certificates that report the full Table 1 window—including Mo 6.0–6.5%, N 0.18–0.25%, and Cu 0.50–1.00%—plus the correct Table 4 thickness row and a 2100 °F anneal statement; and dual SA-312/A312 marking when the heat analysis, heat treatment, mechanical tests, and marking satisfy both editions named on the purchase order. Confirm NPS, wall or schedule, finish, length practice, corrosion-test extras (G48 / CPT), and any product-analysis or supplementary tests on enquiry.
Common commercial names and how they map to the ordered product are listed below—use the full SA-312/A312 designation plus UNS S31254 on the purchase order rather than market shorthand alone.
- ASME SA312 UNS S31254 / SA-312 Grade UNS S31254 — preferred marking language for ASME-code and dual-marked pipe (no TP name exists)
- ASTM A312 UNS S31254 — same grade tables for chemistry and tensile when the ASTM edition is referenced
- UNS S31254 — unified numbering system identity used on MTCs, stencils, and cross-reference tables
- 254 SMO®-type / 6Mo / EN 1.4547 — market and European shorthand; confirm Mo 6.0–6.5%, N 0.18–0.25%, Cu 0.50–1.00%, Cr 19.5–20.5%, Ni 17.5–18.5%, and the thickness-split Table 4 floors before accepting any heat
UNS S31254 is not a drop-in for ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 UNS S31050 Stainless Steel Pipe, or ASME SA312 UNS S31266 Stainless Steel Pipe on a shared “6Mo” or “super-austenitic” market label—each has its own Table 1 row. Versus TP316L, S31254 raises Mo from ~2–3% to 6.0–6.5%, requires intentional N and Cu bands, and carries thickness-split tensile floors well above the 70/25 ksi TP316L row. Versus S31050 (310MoLN / ~2% Mo urea grade), the design intents are opposite: S31050 alloys ~2% Mo for urea/carbamate duty on a 25Cr–22Ni base, while S31254 pushes Mo to ~6% for chloride PREN on a 20Cr–18Ni base with a much higher anneal temperature. Versus S31266, S31254 is the classic 6Mo row without tungsten; S31266 adds W 1.5–2.5%, shifts Mo/N/Cr/Ni, and carries a higher 109/61 ksi tensile floor. Dual marking with TP316L is usually impossible because Mo, N, Cu, and tensile rows differ. Hub: ASME SA 312/SA 312M.
Manufacturing Types (SML / WLD / HCW)
ASME SA-312 defines three manufacturing routes that may be marked on finished UNS S31254 pipe. Selecting the route is a purchase-order decision driven by design code, size range, wall thickness, and inspection preference. It does not change the Table 1 chemistry of S31254—melting must still meet C ≤0.020%, Mn ≤1.00%, P ≤0.030%, S ≤0.010%, Si ≤0.80%, Cr 19.5–20.5%, Ni 17.5–18.5%, Mo 6.0–6.5%, N 0.18–0.25%, and Cu 0.50–1.00%—and every route must still pass through the solution anneal required by SA-312 at the Table 2 2100 °F minimum.
- Seamless (SML) — no welding at any stage of manufacture. Seamless dominates high-pressure seawater and chloride process tubing, thick-wall heat-exchanger pipe, and pressure parts when the project specification excludes welded pipe. Hot-finished or cold-finished seamless must still be solution annealed to 2100 °F [1150 °C] minimum and rapidly cooled.
- Welded (WLD) — automatic welding without filler metal. The weld is finished so that the pipe meets dimensional and mechanical requirements after the final heat treatment required by SA-312. Welded S31254 is common on larger seawater headers when seam quality and post-weld anneal are controlled—confirm before bidding; the plate heat must itself meet S31254 chemistry including Mo, N, and Cu bands.
- Heavily cold-worked (HCW) — welded pipe that is cold worked to a reduction of area of wall and weld of at least 35% before the final anneal, again without filler metal in the longitudinal weld. The weld is radiographed before cold work. HCW is ordered when the buyer wants the HCW marking and the process controls written into SA-312 for that route.
Each finished length is hydrostatically tested or nondestructively electrically tested; the manufacturer may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser agrees to a system test in lieu of hydrotest. Lot definitions follow clause 11.1. Clause 17 heat-treatment lot marking is not mandatory for S31254 (it is not an H grade), but seawater and FGD projects usually demand full heat and lot identity on the stencil for traceability through fabrication. High molybdenum increases hot-work loads and segregation risk—mills must solution-anneal at the Table 2 2100 °F minimum with rapid cool to avoid sigma/chi; grouping project sizes onto one heat improves Mo/N/Cu consistency and often helps meet mill minimum order quantities that are higher than for commodity TP316L.
Lead times are typically longer than for ASME SA312 TP316L Stainless Steel Pipe because specialty melting capacity for 6Mo superaustenitic heats is thinner and mills often treat S31254 as a made-to-order grade. Remnant fills from prior S31254 heats can still cut weeks off small urgent lots when sizes match. Plan procurement early for seamless heavy-wall seawater sizes, and confirm route, edition, wall (because Table 4 is thickness-split), Mo/N/Cu reporting, 2100 °F anneal statement, and any corrosion-test extras (G48) before placing a mill order so the certificate matches the design basis. Where only moderate chloride resistance matters and 6% Mo is not required, switch the conversation to ASME SA312 TP316L Stainless Steel Pipe or ASME SA312 TP317L Stainless Steel Pipe; where urea/carbamate chemistry governs, move to ASME SA312 UNS S31050 Stainless Steel Pipe instead of stretching a 6Mo heat into a urea application.
Chemical Composition of SA312 UNS S31254
Two chemistry layers matter: melting (heat / ladle) analysis—mandatory per heat under ASME SA-312/ASTM A312 Table 1—and product analysis when ordered (Suppl. S1 / PO). SA-312/A312 defer product-analysis tolerances through ASTM A999/A999M §6.3 to ASTM A480/A480M Table A1.1. SHH STEEL reports actual ladle and, when ordered, product values—never unpublished tighter windows. On heat analysis, every certificate must show molybdenum 6.0–6.5%, nitrogen 0.18–0.25%, and copper 0.50–1.00%; spot-check those three values first on receipt, together with C ≤0.020%, because they are the commercial traps that separate S31254 from ordinary TP316L and from neighboring 6Mo grades.
Melting analysis (heat / ladle analysis) — Table 1
Heat analysis for UNS S31254 from ASME SA-312/SA-312M (ASTM A312/A312M) Table 1 is summarized below. Values are maximum unless a range is shown; ellipses (…) mean no requirement in the ordered edition. The grade column in Table 1 shows “…” (no TP designation).
| Element | UNS S31254 melting analysis |
|---|---|
| Carbon (C) | ≤ 0.020 |
| Manganese (Mn) | ≤ 1.00 |
| Phosphorus (P) | ≤ 0.030 |
| Sulfur (S) | ≤ 0.010 |
| Silicon (Si) | ≤ 0.80 |
| Chromium (Cr) | 19.5 – 20.5 |
| Nickel (Ni) | 17.5 – 18.5 |
| Molybdenum (Mo) | 6.0 – 6.5 |
| Nitrogen (N) | 0.18 – 0.25 |
| Copper (Cu) | 0.50 – 1.00 |
Source: SA-312 Table 1, UNS S31254 (TP column “…”). Cr min uses A480 15–20% band (0.20); Cr max uses 20–30% band (0.25). Mo uses over 2–8% band (0.10). N max uses over 0.19–0.25 band (0.02). Footnote C style method-by-agreement practice for N determination should be settled on the PO.
Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1
When product analysis is ordered, apply A480 Table A1.1 tolerances to the Table 1 limits. Product Mo uses the A480 over 2–8% band (0.10 under/over). Nitrogen straddles A480 bands: min 0.18 uses 0.01 under; max 0.25 uses 0.02 over. Copper uses the 0.05 band in the 0.50–1.00 window. Chromium 19.5–20.5% crosses the 20% A480 boundary—this pack applies 0.20 under / 0.25 over accordingly.
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.020 | 0.005 over | ≤ 0.025 |
| Manganese (Mn) | ≤ 1.00 | 0.03 over | ≤ 1.03 |
| Phosphorus (P) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Sulfur (S) | ≤ 0.010 | 0.005 over | ≤ 0.015 |
| Silicon (Si) | ≤ 0.80 | 0.05 over | ≤ 0.85 |
| Chromium (Cr) | 19.5 – 20.5 | 0.20 under / 0.25 over | 19.30 – 20.75 |
| Nickel (Ni) | 17.5 – 18.5 | 0.15 under / over | 17.35 – 18.65 |
| Molybdenum (Mo) | 6.0 – 6.5 | 0.10 under / over | 5.90 – 6.60 |
| Nitrogen (N) | 0.18 – 0.25 | 0.01 under / 0.02 over | 0.17 – 0.27 |
| Copper (Cu) | 0.50 – 1.00 | 0.05 under / over | 0.45 – 1.05 |
Mo 6.0–6.5%: defining 6Mo addition—far above TP316L (~2–3%) or S31050 (~2%). Heats at 5.8% Mo are not S31254. N 0.18–0.25%: stabilizes austenite at high Mo and raises yield strength; must appear on the MTC. Cu 0.50–1.00%: part of the Table 1 envelope—leaving Cu off the certificate is a nonconformance even when Mo is correct. Vs S31266: S31266 uses higher Cr/Ni/N, Mo 5.2–6.2, plus W 1.5–2.5 and higher Cu, with a higher tensile floor (109/61 ksi).
| Element | TP316L | UNS S31050 | UNS S31254 | UNS S31266 |
|---|---|---|---|---|
| C | ≤ 0.035 | ≤ 0.025 | ≤ 0.020 | ≤ 0.030 |
| Cr | 16.0 – 18.0 | 24.0 – 26.0 | 19.5 – 20.5 | 23.0 – 25.0 |
| Ni | 10.0 – 14.0 | 20.5 – 23.5 | 17.5 – 18.5 | 21.0 – 24.0 |
| Mo | 2.00 – 3.00 | 1.60 – 2.60 | 6.0 – 6.5 | 5.2 – 6.2 |
| N | … | 0.09 – 0.15 | 0.18 – 0.25 | 0.35 – 0.60 |
| Cu | … | … | 0.50 – 1.00 | 1.00 – 2.50 |
| W | … | … | … | 1.50 – 2.50 |
| Primary niche | General chloride | Urea / carbamate | Seawater / 6Mo | High-Mo + W |
The side-by-side table above shows why a shared “6Mo” or “super-austenitic” market label is dangerous: ASME SA312 TP316L Stainless Steel Pipe keeps Mo near 2–3%; ASME SA312 UNS S31050 Stainless Steel Pipe alloys ~2% Mo for urea duty; ASME SA312 UNS S31266 Stainless Steel Pipe adds tungsten and a higher tensile floor; S31254 is the classic 6.0–6.5% Mo + N + Cu row aimed at warm-seawater PREN. Buyers who need only moderate chloride resistance should say so early; those needs usually push the conversation toward TP316L or TP317L instead of forcing a 6Mo melt when the Mo/N/Cu bands are not required. Nickel 17.5–18.5% uses the A480 under-20% Ni band (0.15 under/over). Designers should take allowable stresses for UNS S31254 only from the governing code tables for this UNS number—do not copy TP316L allowables into an S31254 calculation package.
Mechanical Properties of SA312 UNS S31254
Room-temperature tensile requirements for UNS S31254 come from ASME SA-312/ASTM A312 Table 4 and are thickness-dependent. Intentional molybdenum, nitrogen, and copper raise the tensile floor well above the 70/25 ksi TP316L defaults, but the tensile floor drops slightly when wall exceeds 0.187 in. [5.00 mm]. Yield stays 45 ksi on both thickness rows. Always match the tensile row to actual ordered wall—a certificate showing only 98/45 for 0.250 in. wall is nonconforming. Actual mill values are often higher than the minima, but design still uses Table 4 for ambient checks and the governing code allowables for elevated-temperature design of S31254.
| Wall thickness t | Tensile min | Yield min |
|---|---|---|
| t ≤ 0.187 in. [5.00 mm] | 98 ksi [675 MPa] | 45 ksi [310 MPa] |
| t > 0.187 in. [5.00 mm] | 95 ksi [655 MPa] | 45 ksi [310 MPa] |
Source: SA-312 Table 4 for UNS S31254. Elongation: 35% longitudinal / 25% transverse (general austenitic rule—S31254 is not in the S31050/S32615 special 25% L group). Hardness: no Table 4 maximum asserted here. No Table 5 grain-size requirement (not an H grade).
Elongation 35% L / 25% T matches the family default; do not confuse S31254 with the special 25% L pair used for S31050. Base mechanical testing includes tension on a lot basis and flattening (or the alternate bend where the standard permits) typically on 5% of the lot, plus hydrotest or NDE on every length. Elevated-temperature tensile and rupture tests are purchase-order options, not base SA-312 requirements. For pressure-retaining parts, use the governing Section II Part D or project-code allowables for UNS S31254 where listed—do not copy TP316L / S31603 allowable-stress tables into an S31254 calculation package, and do not mix thin-wall and heavy-wall Table 4 rows in the same release. Annealed S31254 retains fully austenitic toughness to low temperature; impact testing is a construction-code or PO matter, not an SA-312 base test.
Although Table 4 has no hardness maximum, fabricators sometimes set a Rockwell limit for bending or expanding—put any such limit on the PO and verify it on the MTC if required. Like other superaustenitics, S31254 hardens when cold worked; intermediate anneals may be needed for severe forming, and those anneals must still meet the Table 2 2100 °F practice. After long intermediate-temperature service, expect reduced room-temperature ductility from Mo-rich intermetallics (sigma/chi)—evaluate before cold repair. For urea/carbamate duty without the 6Mo seawater chemistry case, see ASME SA312 UNS S31050 Stainless Steel Pipe rather than stretching an S31254 heat into a urea application.
Dimensions and Tolerances
Dimensional supply for SA312 UNS S31254 pipe follows ASME B36.19 schedules for common NPS/schedule combinations, with special OD and wall by agreement when seawater exchangers, FGD chloride lines, or bleach-plant headers need a non-standard section. Outside-diameter variations follow ASTM A999/A999M; wall-thickness variations follow SA-312 Table 3 as summarized below. Wall thickness also drives the Table 4 tensile row at the 0.187 in. [5.00 mm] split—state ordered wall clearly, and state whether wall is nominal or minimum (Suppl. S8) on the purchase order so the mill does not ship the wrong interpretation.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
Source: SA-312 Table 3; outside diameter variations per A999/A999M.
- Lengths — NPS 1/8–8 commonly furnished up to 24 ft unless otherwise agreed; SRL, DRL, or cut-to-length on order
- Cut lengths — typically ≤1/4 in. [6 mm] over unless the PO states a tighter band
- Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen
Seawater and chloride-process industries often order by OD × wall rather than by NPS/schedule. Special OD × wall combinations are common in exchangers and headers where ASME B36.19 schedules leave gaps—state whether wall is minimum or nominal before the mill rolls, because the Table 4 thickness split makes wall a mechanical as well as a dimensional decision. Straightness, end finish, and length tolerance should be written explicitly for export projects so receiving inspection has a clear acceptance basis. For socket-weld or threaded ends on thin schedules, confirm the wall remains adequate after the 12.5% under-tolerance. Jointers are not permitted unless the purchase order expressly allows them; cut-to-length programmes should include an allowance for fit-up scrap so the mill does not ship under-length pieces.
Equivalent Grades
Equivalence for UNS S31254 is primarily an ASME/ASTM identity question. The governing pipe designation is ASME SA-312 UNS S31254 (no TP name); market names and plate counterparts must be mapped back to that row before a mill is asked to dual-mark or substitute.
| Designation | Notes |
|---|---|
| ASME SA-312 UNS S31254 | Governing pipe grade (no TP designation) |
| ASTM A312 UNS S31254 | Same Table 1 / Table 4 when the ASTM edition is referenced |
| 254 SMO®-type (trade) | Confirm full Table 1 incl. Mo 6.0–6.5, N 0.18–0.25, Cu 0.50–1.00 on MTC |
| EN 1.4547 / X1CrNiMoCuN20-18-7 approx. | Engineering map—recheck every limit before dual certification |
| SA-240 / A240 S31254 | Plate/sheet counterpart when listed—not a pipe specification by itself |
Related SA-312 grades on steelspecs.com: ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 TP317L Stainless Steel Pipe, ASME SA312 UNS S31050 Stainless Steel Pipe, ASME SA312 UNS S31266 Stainless Steel Pipe, ASME SA312 UNS S32053 Stainless Steel Pipe, ASME SA312 UNS S31002 Stainless Steel Pipe. Versus ASME SA312 TP316L Stainless Steel Pipe, S31254 is the 6Mo superaustenitic row—not a synonym. Versus ASME SA312 UNS S31050 Stainless Steel Pipe, the design intents are opposite (seawater 6Mo vs urea ~2% Mo). Versus ASME SA312 UNS S31266 Stainless Steel Pipe, S31254 lacks tungsten and carries a lower tensile floor. Always re-check C, Mo, N, Cu, Cr, Ni, and the thickness-split tensile row against Table 1 / Table 4 before accepting a substitute heat, and do not treat “254 SMO” and “TP316L” as automatically interchangeable on the purchase order.
Heat Treatment and Delivery Condition
UNS S31254 is listed in Table 2 at 2100 °F [1150 °C] minimum (with S32654) with rapid cooling. This is higher than the 1900 °F default used for many 300-series and 310 grades—required to dissolve Mo-rich intermetallics (sigma/chi). Because S31254 is not an H grade, clause 6.2 reheat language does not apply and direct quench after hot forming is accepted the way it is for non-H grades such as ASME SA312 TP316L Stainless Steel Pipe. There is no Table 5 grain-size rule. Delivery remains the solution-annealed condition required by SA-312 unless the ordered edition and purchase order state otherwise.
- Solution anneal ≥2100 °F [1150 °C] — Table 2 (with S32654); rapid cool
- No Table 5 grain-size rule — not an H grade
- Clause 17 lot marking — not mandatory for S31254; seawater / FGD projects usually request heat/lot identity
- Free of scale and exogenous iron — descaled / pickled or equivalent as ordered (critical for crevice resistance)
- Bright anneal / high-cleanliness finish — available on request when the end-user specification requires a scale-free surface for seawater or clean-process service
Annealing at 2100 °F dissolves Mo-rich intermetallics and restores corrosion resistance after hot work; rapid cooling is required. Shipping “annealed at 1900 °F” is a nonconformance even if tensile passes—the Table 2 2100 °F row is mandatory language for S31254. Bright annealing under hydrogen or vacuum can deliver a scale-free surface preferred for clean seawater service; pickled finishes are acceptable when fully rinsed and free of embedded scale. Owner-specified post-fabrication heat treatments are purchaser requirements, not SA-312 base rules—write temperature and time on the PO if needed. Cite the ordered edition’s Table 2 2100 °F practice on the enquiry so the mill does not apply a neighboring grade’s 1900 °F habit to an S31254 heat by mistake.
Corrosion Resistance
UNS S31254 is aimed at warm seawater, chloride brines, and acidic chloride process streams where 316L and 904L pit or crevice. High molybdenum 6.0–6.5%, nitrogen 0.18–0.25%, and copper 0.50–1.00% support pitting and crevice resistance in the PREN class typically ~42–45 (calculated commentary from specification minima—not a Table 1 published value). SA-312 itself publishes no CPT/CCT numbers—project corrosion testing (e.g. ASTM G48) is contractual, not Table 4.
- Warm seawater piping / heat exchangers — primary niche; watch chlorination, crevice geometry, and deposits
- Flue-gas desulfurization chloride lines — acidic chlorides; confirm temperature and composition
- Pulp & paper bleach plants — chloride oxidants; compare ASME SA312 UNS S31266 Stainless Steel Pipe if higher strength is needed
- Fully austenitic toughness — no duplex 475 °C embrittlement rule; tough at low temperature
- Urea / carbamate — ASME SA312 UNS S31050 Stainless Steel Pipe is usually the dedicated choice; do not stretch S31254 into urea duty without engineering review
Verify intergranular resistance with Suppl. S7 (ASTM A262 Practice E) when the service case is critical, and use Suppl. S9 weld-decay testing when welded pipe must demonstrate comparable weld and base-metal loss rates. Neither test is automatic—order them when the corrosion case needs proof. Crevice geometry, chlorination practice, and under-deposit conditions dominate real seawater performance—material selection alone does not replace good design. Compared with ASME SA312 TP316L Stainless Steel Pipe, S31254 trades commodity availability for intentional 6Mo + N + Cu chemistry and thickness-split tensile floors aimed at warm-seawater PREN. If only moderate chloride resistance matters and 6% Mo is not required, TP316L or TP317L is usually the more available and economical choice; specify S31254 only when the 6Mo chemistry is actually needed.
Applications of SA312 UNS S31254 Pipe
Buyers typically select UNS S31254 when the project already wants superaustenitic chloride resistance with intentional ~6% molybdenum, nitrogen, and copper for warm seawater or acidic chloride service that ordinary TP316L (Mo ~2–3%, no N/Cu requirement) cannot answer cleanly. The grade earns its keep by protecting both seawater piping integrity and welded HAZ behaviour under low carbon and high Mo, while remaining fully austenitic.
| Application | Why S31254 | Note |
|---|---|---|
| Seawater piping / heat exchangers | 6Mo PREN class ~42+ | Watch chlorination / crevice design |
| Flue-gas desulfurization chloride lines | Acidic chlorides | Confirm T and composition |
| Pulp & paper bleach plants | Chloride oxidants | Compare S31266 if higher strength needed |
| Offshore / coastal process piping | Warm seawater resistance | Often seamless; confirm wall for Table 4 row |
| Acidic chloride chemical lines | High Mo + N + Cu | Validate concentration / temperature |
If only moderate chloride resistance matters, see ASME SA312 TP316L Stainless Steel Pipe or ASME SA312 TP317L Stainless Steel Pipe—they are usually more available and carry simpler single tensile rows. If urea/carbamate chemistry governs, see ASME SA312 UNS S31050 Stainless Steel Pipe rather than forcing a 6Mo heat into a urea design basis. If higher strength with tungsten is the driver, compare ASME SA312 UNS S31266 Stainless Steel Pipe. Typical enquiry packages list design pressure, seawater vs process chloride duty, wall (for the Table 4 thickness split), whether field welding will be performed, and whether G48/CPT or S7 are mandatory—adding those extras early avoids late schedule slips. When replacing TP316L with S31254 in an existing unit, review weld procedures, filler selections, and receiving checklists for Mo, N, and Cu—the base-metal change alone does not update the WPS.
Weldability
UNS S31254 welds with GTAW, GMAW, SMAW, and SAW using overalloyed Ni-Cr-Mo practices familiar to fabricators of other 6Mo grades. Low carbon improves as-welded intergranular resistance in the heat-affected zone; intentional Mo, N, and Cu mean procedures should be qualified on S31254 chemistry rather than assumed from a TP316L PQR. Mill WLD and HCW longitudinal welds are autogenous (no filler); Table 6 guidance applies to joining with filler, not to the mill seam. Control heat input to limit Mo-rich intermetallics.
Filler and Table 6: S31254 is not assigned an AWS class in the extracted Table 6—filler selection is by agreement and must be recorded on the WPS. Industry often freezes overalloyed Ni-Cr-Mo consumables (ERNiCrMo-3 / -4 type practice) so deposited metal stays close to or above the base-metal Mo intent; do not improvise from 316L or commodity 300-series stock. Freeze the AWS (or EN) class on the WPS/PQR before production welds—Table 6 silence means the WPS must lock the class explicitly.
- Moderate heat input; clean joints free of oil, paint, and exogenous iron
- Argon shielding and backing gas for GTAW root passes
- Remove heat tint; pickle or passivate when seawater / chloride service follows
- Mill seams autogenous; clause 15 repairs must identify any filler used
Qualify welding procedures to ASME Section IX on S31254 material (or on a heat with matching Mo, N, and Cu). A PQR on ASME SA312 TP316L Stainless Steel Pipe without review can miss the Mo/N effect on weld-pool behaviour and the need for an overalloyed filler. Dissimilar welds of S31254 to carbon steel still commonly use 309-type fillers for dilution control; if the weld must also resist seawater attack, decide whether the filler itself needs matching or overmatching Mo or whether a barrier butter layer is required, and capture that decision in the WPS. After intermediate-temperature service exposure, clean thoroughly before repair welding and follow producer guidance for 6Mo repair practice.
Surface Finishes
Surface condition for SA312 UNS S31254 pipe is stated on the purchase order. Cleanliness matters for seawater and chloride service—embedded free iron, mill scale, and chloride-bearing residues become crevice initiators that defeat the 6Mo chemistry advantage the buyer paid for. Typical mill finishes available from SHH STEEL supply include the following options:
- Annealed and pickled (AP) — solution annealed at ≥2100 °F, descaled in acid pickle or an equivalent process, producing a matte gray finish common for process pipe; pickle quality is corrosion-critical
- Blasted and pickled — often used for heavy-wall seamless where scale removal benefits from blast first
- Bright annealed (BA) — annealed in a protective atmosphere to a brighter, scale-free surface preferred for many seawater services where mill capability exists for the size; temperature must still meet the Table 2 2100 °F practice
- High-cleanliness for seawater / clean-process service — by agreement when end-user specs demand extra cleanliness beyond standard pickle
- Mechanically polished — grit or Ra-controlled polish on OD and/or ID when ordered; polishing does not replace solution annealing
- Bead-finished welded OD — weld bead rolled or ground flush as agreed for WLD/HCW product
Passivation after pickle or polish can be added when the end-user specification requires it—often specified for seawater service even though SA-312 itself does not mandate passivation. Electropolishing is available for special clean-service needs by agreement. Use low-halide marking inks when the project specification bans chloride-bearing inks. State finish, passivation, and any ink restriction on the order so the mill does not ship a default AP finish into a BA or high-cleanliness requirement.
Inspection and Testing
Base inspection and testing for SA-312 UNS S31254 pipe combines chemistry (especially Mo, N, and Cu), mechanical (correct thickness row and 35%/25% elongation), heat-treatment proof (2100 °F anneal statement), and integrity checks. The following items form the usual acceptance package; supplementary requirements and project corrosion extras apply only when written on the purchase order.
- Heat (melting) analysis — mandatory per heat against Table 1 for UNS S31254, including C ≤0.020%, Mn ≤1.00%, P ≤0.030%, S ≤0.010%, Si ≤0.80%, Cr 19.5–20.5%, Ni 17.5–18.5%, Mo 6.0–6.5%, N 0.18–0.25%, and Cu 0.50–1.00%
- Product analysis — when ordered (Suppl. S1 / purchase-order language), using A480 Table A1.1 tolerances via A999 §6.3
- Tension test — Table 4 tensile and yield on the correct thickness row (98/45 or 95/45 ksi) plus 35% L / 25% T elongation on a lot basis
- Flattening test — or alternate bend where the standard permits (typically on 5% of the lot)
- Hydrostatic test or nondestructive electric test — each length; manufacturer’s option unless the order fixes the method
- Visual and dimensional check — against ordered NPS/schedule or OD/wall and the applicable tolerance clauses; confirm UNS S31254 (not a TP name) on every stencil
Mill test certificates: EN 10204 3.1 is the standard documentation package from SHH STEEL supply. The certificate must report molybdenum 6.0–6.5%, nitrogen 0.18–0.25%, and copper 0.50–1.00% so receiving inspection can verify the commercial traps that separate S31254 from TP316L; the correct Table 4 thickness row, 35%/25% elongation, and a 2100 °F anneal statement must also appear. EN 10204 3.2 or third-party witness (SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency) is arranged when specified and should be booked before final testing. Dual ASME SA-312 / ASTM A312 certification is available when chemistry, heat treatment, mechanical tests, and marking satisfy the edition(s) named on the order.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms Mo, N, Cu, and other elements on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S8 minimum wall | Wall interpreted as minimum rather than nominal (also affects Table 4 row) |
| S9 weld decay | Compares weld and base-metal loss rates |
| G48 / CPT | Project corrosion proof (contractual—not SA-312 base) |
Receiving review should confirm C ≤0.020, Mo 6.0–6.5, N 0.18–0.25, Cu 0.50–1.00, Cr 19.5–20.5, Ni 17.5–18.5, the correct thickness-row tensile/yield, 35%/25% elongation, 2100 °F anneal statement, and hydro or NDE method. Third-party inspectors should verify that the grade stencil reads UNS S31254—not merely “254 SMO,” “6Mo,” or “316L upgrade.” PMI by OES on a sample length is a useful receiving check when multiple superaustenitic grades share a laydown area; guns that only report Cr and Ni are insufficient to release S31254 stock. Mechanical tests follow clause 11.1 lot rules; for specialty 6Mo heats made in short campaigns, a lot may be only a few dozen lengths, so base test frequency is effectively high.
Packaging and Shipping
Export and domestic shipments of SA312 UNS S31254 pipe are packed for handling and ocean or land transport. Typical packing practices from SHH STEEL supply include:
- Seaworthy bundles — pipes strapped or cradled in bundles sized for container or break-bulk handling, with non-metallic separators where needed to protect finish; cradles or individual supports for heavy headers
- End caps / protectors — plastic or metal caps on plain or beveled ends to reduce damage and contamination during transit
- Marking — durable marking of specification, grade (UNS S31254—no TP name), heat number, size (NPS or OD × wall / schedule), manufacturing type (SML / WLD / HCW), test letters, and mill identity as required by SA-312 and the purchase order
- Export packing — waterproof wrapping or desiccant as agreed for polished or bright-annealed finishes; container stuffing photos on request; low-chloride inks on request
Segregate UNS S31254 from ASME SA312 TP316L Stainless Steel Pipe, ASME SA312 UNS S31050 Stainless Steel Pipe, and ASME SA312 UNS S31266 Stainless Steel Pipe on the packing list and in the yard so stencil mix-ups do not travel with the shipment—mix-ups discovered after fabrication are expensive because Mo, N, and Cu bands cannot be converted by heat treatment alone. Shipping S31254 in crates labeled only “6Mo” or “254 SMO” without the UNS risks confusion with neighboring superaustenitics or with commodity TP316L. When S31254 ships with TP316L on the same vessel, use separate bundles and distinctly colored tags. Receiving inspectors should compare stencil heat numbers against the MTC for every length and verify that Mo 6.0–6.5%, N 0.18–0.25%, Cu 0.50–1.00%, the correct Table 4 thickness row, and a 2100 °F anneal statement are reported before release to fabrication. Keep interiors dry and capped so chloride-bearing moisture does not stain or pit the surface before installation. Shipment docs typically include packing list, invoice, B/L or AWB, and MTC (3.1 or 3.2) with full Table 1 chemistry reported, plus origin/customs papers per Incoterms.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless plate and pipe. For ASME SA312 UNS S31254 we quote against the edition you name, report the full Table 1 window on the MTC—including Mo 6.0–6.5%, N 0.18–0.25%, Cu 0.50–1.00%, C ≤0.020%, Cr 19.5–20.5%, and Ni 17.5–18.5%—and keep heat identity unbroken from melt through finished length. Receiving inspection then clears the heat against Table 1 and the correct Table 4 thickness row rather than against a vague “254 SMO” or “6Mo” catalog sheet. We flag missing Mo, N, or Cu fields, wrong tensile row for wall, absent 2100 °F anneal statement, or absent 35%/25% elongation on supplier MTCs before shipment, so non-conforming paperwork is caught at the mill—not at the fabricator. We also stay honest about Table 6 (no AWS filler class listed) and about PREN as calculated commentary rather than a Table 1 published value, so those items stay closed by agreement on the quotation and WPS.
- Specification fidelity — chemistry and tensile to SA-312/A312 Table 1 and Table 4 for UNS S31254; Mo/N/Cu/C reported and checked; correct 98/45 or 95/45 row; 2100 °F anneal stated; no commodity TP316L sold as 6Mo / S31254
- Mill resources — SML, WLD, and HCW from qualified stainless pipe mills with heat traceability; cutting and beveling on confirmed orders
- Documentation — EN 10204 3.1 MTCs standard with full Table 1 chemistry including Mo, N, and Cu; 3.2 or third-party inspection on request
- Dual marking — ASME SA-312 and ASTM A312 when the heat and tests meet both requirements you name
- Related grades — sister SA-312 grades (ASME SA312 TP316L Stainless Steel Pipe / ASME SA312 UNS S31050 Stainless Steel Pipe / ASME SA312 UNS S31266 Stainless Steel Pipe) when projects buy matched packages
- Export packing — seaworthy bundles, end protectors, and durable UNS/heat/size/type marking
Quotations follow your purchase-order language for edition year, manufacturing type, size, wall (for the Table 4 split), finish, corrosion-test extras (G48 / CPT), and any supplementary tests you name (S1, S5, S7, S8, S9). Ask for coordinated plate-and-pipe heats when a project needs matching Mo/N/Cu levels across SA-240 and SA-312 forms. Grade hub: ASME SA 312/SA 312M.
Supply Capability
SHH STEEL can supply ASME SA312 UNS S31254 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.
| Item | SHH STEEL capability for UNS S31254 |
|---|---|
| Standard | ASME SA-312/SA-312M and/or ASTM A312/A312M UNS S31254 (no TP designation) |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD/wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | SRL, DRL, or cut-to-length |
| Finish | Annealed and pickled; blasted and pickled; bright annealed or high-cleanliness by agreement |
| Testing | Tension (correct t row), flattening/bend, hydro or NDE per length; Mo/N/Cu on MTC; 2100 °F anneal stated; S1/S5/S7/S8/S9 and G48/CPT on order |
| Documents | EN 10204 3.1 with full Table 1 chemistry reported; third-party inspection / 3.2 on request |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
UNS S31254 is less common in distributor stock than TP316L, so mill-run orders are typical and lead times track specialty melt schedules for 6Mo superaustenitic heats. Common sizes may occasionally be available from remnant lengths of prior S31254 heats; heavy walls and special OD/wall combinations for seawater exchangers are mill-order items. Enquiries should state the SA-312 edition, UNS S31254 (not a bare “254 SMO” or “6Mo”), SML/WLD/HCW, NPS or OD×wall (nominal or minimum—wall drives Table 4), length practice, finish, Mo/N/Cu reporting expectation, 2100 °F anneal expectation, corrosion-test extras, and any product-analysis or 3.2 requirements so mill slots align with your need date. Cut lengths, beveling, and packing-list marking are available on confirmed orders. Combining project sizes into one heat improves Mo/N/Cu consistency and helps meet mill minima without over-ordering. For urgent small quantities, ask about remnant lengths from recent S31254 heats before authorizing a new melt—remnants can cut weeks from the schedule when sizes match.
FAQ
-
Is ASME SA312 the same as ASTM A312?
- For chemistry (Table 1), tensile (Table 4), manufacturing types, and most testing language, ASME SA-312/SA-312M matches ASTM A312/A312M of the referenced edition. Dual SA312/A312 marking is common when ordered. Name both editions on the purchase order and mill test certificate so inspectors can verify the heat against the exact books you cited—do not assume a bare market grade stamp covers dual certification for UNS S31254.
-
What is the UNS number for this grade?
- Table 1 lists S31254 as the unified number for this pipe grade, with an ellipsis in the TP column—there is no separate TP designation. Cite UNS S31254 on the purchase order, stencil, packing list, and mill test certificate so chemistry and tensile rows cannot be confused with a neighboring 6Mo grade that shares a “254 SMO” commercial nickname.
-
UNS S31254 vs TP316L — which should I order?
- TP316L is the workhorse Mo-bearing austenitic with C ≤0.035%, Mo ~2–3%, no N or Cu requirement, and 70/25 ksi floors. UNS S31254 is a 6Mo superaustenitic (Mo 6.0–6.5%, N 0.18–0.25%, Cu 0.50–1.00%) with thickness-split 98/45 or 95/45 ksi floors and a 2100 °F anneal. Not a drop-in for 316L. Put the design-code grade and UNS on the datasheet and purchase order before you compare price—switching to TP316L after fabrication drawings are frozen usually means a material change notice, not a free mill substitution.
-
UNS S31254 vs UNS S31266 — which should I order?
- Both are high-Mo superaustenitics. S31254 is the classic 6.0–6.5% Mo + N + Cu row without tungsten. S31266 adds W 1.5–2.5%, shifts Mo/N/Cr/Ni, and carries a higher 109/61 ksi tensile floor. Order the exact UNS on the datasheet—do not treat “6Mo” as a free substitute between them. Put the design-code grade and UNS on the purchase order before you compare price—switching after fabrication drawings are frozen usually means a material change notice.
-
UNS S31254 vs UNS S31050 — which should I order?
- S31050 is the 25Cr-22Ni-2Mo-N (310MoLN-type) urea/carbamate grade with ~2% Mo and thickness-split 84/39 or 78/37 ksi floors. S31254 is a 6Mo superaustenitic aimed at warm seawater and high-PREN chloride service, with a 2100 °F anneal. They solve different problems—do not substitute one for the other on a shared “specialty stainless” label. Put the design-code grade and UNS on the purchase order before you compare price.
-
Seamless vs welded UNS S31254 — which is better?
- Neither is universally better. Choose the manufacturing type your design code and datasheet allow; both are legitimate SA-312 forms when tested to the standard, and both must still meet S31254 chemistry including Mo 6.0–6.5%, N 0.18–0.25%, and Cu 0.50–1.00%, plus the Table 2 2100 °F anneal. High-pressure seawater tubing is often seamless; larger seawater headers may use welded when seam quality is controlled. State SML, WLD, or HCW on the purchase order and confirm the same letters on the pipe marking and MTC—mixing offers that differ only in manufacturing type is a common bid-evaluation trap.
-
Can you dual-certify SA312 / A312 UNS S31254?
- Yes, when heat analysis (including Mo 6.0–6.5%, N 0.18–0.25%, and Cu 0.50–1.00%), solution anneal at 2100 °F, mechanical tests on the correct Table 4 thickness row, and marking meet both editions named on the order. Write the ASME and ASTM edition years on the PO, and require the MTC to reference both books so receiving inspection can clear the heat without a second paperwork chase after shipment. Dual marking with TP316L is usually impossible because Mo, N, Cu, and tensile rows differ.
-
Hydrostatic test vs NDE — which do I get?
- Each length is hydrotested or nondestructively electrically tested. Manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification locks one method, state it on the PO and verify the chosen test appears on the MTC for every length—silent mill option is not the same as an approved project method for UNS S31254.
-
What heat treatment / anneal temperature applies to UNS S31254?
- Table 2 lists 2100 °F [1150 °C] minimum (with S32654)—higher than the 1900 °F default used for many 300-series grades, required to dissolve Mo-rich intermetallics. It is not an H grade, so clause 6.2 reheat and Table 5 grain size do not apply. Delivery remains the solution-annealed condition required by SA-312 unless the edition and PO state otherwise. Cite the ordered edition’s Table 2 2100 °F row on the enquiry so the mill does not apply a neighboring grade’s 1900 °F habit by mistake.
-
What Table 1 chemistry defines UNS S31254?
- Table 1: C ≤0.020%, Mn ≤1.00%, P ≤0.030%, S ≤0.010%, Si ≤0.80%, Cr 19.5–20.5%, Ni 17.5–18.5%, Mo 6.0–6.5%, N 0.18–0.25%, Cu 0.50–1.00% (no TP designation). Values are melting-analysis limits from the ordered edition—do not invent tighter catalog windows. When product analysis is needed, order it explicitly (Suppl. S1 / PO language) rather than assuming ladle values alone will satisfy receiving inspection.
-
What are the Table 4 tensile requirements for UNS S31254?
- Table 4 is thickness-dependent: t ≤ 0.187 in. [5.00 mm] uses 98 ksi [675 MPa] / 45 ksi [310 MPa]; thicker product uses 95 ksi [655 MPa] / 45 ksi [310 MPa]; elongation is 35% longitudinal / 25% transverse. Yield stays 45 ksi on both rows. Always match the row to ordered wall—do not release heavy wall to the thin-wall 98/45 floor alone. Design to Table 4 unless the mill has accepted higher guaranteed values in writing. Actual MTC readings are often above the floor; still use Table 4 minima for allowable-stress calculations unless the PO states higher guarantees.
-
What filler metal should I use to weld UNS S31254 pipe?
- Table 6 assigns no AWS class for S31254—filler by agreement. Industry often freezes overalloyed Ni-Cr-Mo consumables (ERNiCrMo-3 / -4 type practice) so deposited metal stays close to or above the base-metal Mo intent; do not improvise from 316L or commodity 300-series stock. Freeze the AWS (or EN) class on the WPS/PQR before production welds, and remember mill WLD/HCW longitudinal welds are autogenous—Table 6 guidance applies to joining with filler, not to the mill seam.
Conclusion
ASME SA312 UNS S31254 is the classic TP-less 6Mo super-austenitic pipe grade: C ≤0.020%, Cr 19.5–20.5%, Ni 17.5–18.5%, Mo 6.0–6.5%, N 0.18–0.25%, Cu 0.50–1.00%, thickness-split Table 4 floors of 98/45 or 95/45 ksi with 35% L / 25% T elongation, and a Table 2 2100 °F [1150 °C] anneal (with S32654). It is not a drop-in for TP316L (~2–3% Mo, 70/25 ksi), UNS S31050 (~2% Mo urea grade), or UNS S31266 (W-bearing, higher tensile)—each has its own Table 1 row. Table 6 lists no AWS filler class (filler by agreement). Order the manufacturing type (SML/WLD/HCW), schedule or wall (wall drives Table 4), finish, Mo/N/Cu reporting, 2100 °F anneal proof, and any product analysis, G48/CPT, or supplementary tests explicitly. For stock checks, mill certificates, or dual SA-312/A312 supply questions, contact SHH STEEL at admin@steelspecs.com or browse the ASME SA 312/SA 312M category on steelspecs.com.