ASTM A312 TP316N Stainless Steel Pipe | ASTM A312 Stainless Steel - SHH STEEL

ASTM A312 TP316N Stainless Steel Pipe

ASTM A312 TP316N / UNS S31651 nitrogen-strengthened 316 pipe in SML, WLD and HCW, with C ≤0.08%, Mo 2.00–3.00% and N 0.10–0.16%, an 80/35 ksi Table 4 floor and a 1900 °F default anneal, supplied by SHH STEEL with EN 10204 3.1 MTCs.
Grade
TP316N / UNS S31651
Standard
ASTM A312 / A312M
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASTM A312 TP316N Stainless Steel Pipe

ASTM A312/A312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. It is an ASTM product specification in its own right; ASME SA-312 is a separate Code Book adoption of related text, and the two should not be treated as interchangeable titles on a purchase order. This page is written against A312/A312M for TP316N / UNS S31651, with numbers taken from the referenced A312/A312M tables.

Within that scope, TP316N / UNS S31651 is the nitrogen-strengthened 316 grade with the higher 80/35 ksi Table 4 floor. Table 1 allows carbon up to 0.08% and requires nitrogen at 0.10–0.16%, with Cr 16.0–18.0%, Ni 10.0–14.0%, and Mo 2.00–3.00%. The nitrogen is there mainly for strength: Table 4 releases TP316N at 80 ksi [550 MPa] tensile / 35 ksi [240 MPa] yield with 35% L / 25% T elongation, five ksi above the ordinary TP316 floor on both tensile and yield. UNS S31651 is not individually listed in Table 2, so the default solution anneal at 1900 °F [1040 °C] minimum with rapid cooling applies. TP316N is not an H grade and does not carry Table 5 grain-size control.

SHH STEEL can supply ASTM A312 TP316N stainless steel pipe as seamless (SML), welded (WLD), or heavily cold-worked (HCW) product in ASME B36.19 schedules and special OD/wall combinations, with EN 10204 3.1 mill test certificates as standard and third-party 3.2 inspection when the enquiry asks for it. Dual A312/SA-312 marking is available only when the purchase order names both editions and the mill heat qualifies under each—do not assume a single stamp covers Code stamping without that instruction. For the separate ASME-framed page on the same grade, see SA312 TP316N.

Trade names such as 316N or S31651 only match this specification when the MTC shows the nitrogen band and the 80/35 ksi release. Do not treat a TP316LN heat as interchangeable: LN keeps carbon at ≤0.035% and stays on the 75/30 ksi row, while N allows up to 0.08% C and claims the higher tensile floor. Confirm code allowables for S31651 before down-gauging wall on the strength argument alone.

Within the ASTM A312 series, buyers comparing TP316N usually look next at A312 TP316, A312 TP316LN, A312 TP316L, A312 TP304N, and A312 TP316H. Browse the full grade list on the A312/A312M hub when the datasheet leaves more than one 316-family option open.

Manufacturing Types (SML / WLD / HCW)

ASTM A312 recognizes three manufacturing routes for TP316N pipe, and the route is a purchase-order decision driven by the design code, the size range, wall thickness, and how the owner wants the pipe inspected. The route never changes the chemistry: whichever way the pipe is made, the heat must still meet C ≤0.08%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00%, and N 0.10–0.16%, and every length must still go through the solution anneal at 1900 °F [1040 °C] minimum before it is released.

  • Seamless (SML) — no welding at any stage. Preferred for high-pressure service, thick walls, and owners who exclude welded pipe from the design class. When the higher 80/35 ksi floor is the reason for choosing TP316N, confirm that the manufacturing route and wall schedule still satisfy the code minimum thickness after under-tolerance.
  • Welded (WLD) — automatic welding without filler metal, with the weld finished so the pipe meets dimensional and mechanical requirements after the final heat treatment. The strip or plate heat must itself carry the full TP316N chemistry, so ask for the coil or plate heat number on the certificate.
  • Heavily cold-worked (HCW) — welded pipe cold worked to at least 35% reduction of wall and weld before the final anneal, again without filler in the longitudinal seam, with the weld radiographed before cold work. Order HCW when the project specifically wants that marking and the process controls A312 writes around it.

Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test in place of the hydrotest, and lots for mechanical testing follow the sampling clauses in the referenced edition. State SML, WLD, or HCW on the enquiry so mill slots and test plans line up before the heat is poured.

Chemical Composition of ASTM A312 TP316N

ASTM A312 TP316N chemistry is checked first at the melt and, when ordered, again on the finished pipe. Table 1 allows carbon up to 0.08%—the ordinary 316 ceiling—while requiring nitrogen at 0.10–0.16% so the heat can claim the 80/35 ksi Table 4 row. Mo 2.00–3.00% keeps the chloride resistance of the 316 family.

Melting-analysis limits for TP316N / UNS S31651 appear below.

Element TP316N / UNS S31651 melting analysis
Carbon (C) ≤ 0.08
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 16.0 – 18.0
Nickel (Ni) 10.0 – 14.0
Molybdenum (Mo) 2.00 – 3.00
Nitrogen (N) 0.10 – 0.16

Product-analysis bounds after A480 A1.1 follow. Nitrogen’s product window is 0.09–0.17%, and carbon may reach 0.09% on product analysis only when the heat met ≤0.08%.

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.08 0.01 over ≤ 0.09
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 16.0 – 18.0 0.20 under / over 15.80 – 18.20
Nickel (Ni) 10.0 – 14.0 0.15 under / over 9.85 – 14.15
Molybdenum (Mo) 2.00 – 3.00 0.10 under / over 1.90 – 3.10
Nitrogen (N) 0.10 – 0.16 0.01 under / over 0.09 – 0.17

Do not confuse the nitrogen band with an H-grade package: TP316N has no Table 5 grain-size requirement and no mandatory 0.04% carbon floor. If the project needs creep-oriented H rules, look at A312 TP316H instead of stretching a TP316N heat.

Mechanical Properties of ASTM A312 TP316N

Table 4 is the reason most buyers choose ASTM A312 TP316N: the release floor sits at 80 ksi tensile and 35 ksi yield, five ksi above ordinary TP316 on both columns, with the same 35% L / 25% T elongation requirement. Those figures are lot minima, not typical values.

Property TP316N
Tensile, min 80 ksi [550 MPa]
Yield, min 35 ksi [240 MPa]
Elongation 35% L / 25% T

The higher floor comes from the mandatory 0.10–0.16% nitrogen, not from a different Cr-Ni-Mo balance. If a quoted heat shows 80/35 ksi but nitrogen below 0.10%, it is not TP316N under Table 1 regardless of the tensile result. Keep chemistry and tensile tied together on the certificate.

Dimensions, Tolerances and Stock Sizes

Dimensional supply for ASTM A312 TP316N pipe follows ASME B36.19 schedules for the common NPS and schedule combinations, with special OD and wall available by agreement when a project needs a section the schedules do not cover. Outside-diameter variations follow ASTM A999/A999M, and wall-thickness variations follow A312 Table 3 as summarized below. State on the purchase order whether wall is nominal or minimum (Supplementary S8), because the two readings produce different pipe from the same size line.

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%
  • Lengths — single random, double random, or cut-to-length on order
  • Cut lengths — typically no more than 1/4 in. [6 mm] over the ordered length unless the PO states a tighter band
  • Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen

When the 80/35 ksi floor is used to justify a thinner wall, recalculate after applying Table 3 under-tolerance—strength on the MTC does not erase dimensional minima. Straightness, end finish, and length tolerance should be written into export orders so receiving inspection has an agreed acceptance basis instead of arguing after arrival. Jointers are not permitted unless the purchase order allows them, so cut-to-length programmes should include an allowance for fit-up scrap rather than expecting the mill to ship short pieces.

Stock / Available sizes. SHH STEEL quotes TP316N against a practical stock-and-mill enquiry range rather than a frozen warehouse SKU list. The representative sizes below are the combinations we most often discuss for ASTM A312 TP316N; availability by manufacturing type and exact wall still has to be confirmed on enquiry, and we do not publish fake tonnages against individual lines.

Representative size Typical schedules / notes
NPS 1/2 – 2 Sch 10S / 40S / 80S; common process take-offs
NPS 2-1/2 – 6 Sch 10S / 40S / 80S; frequent mill and stock enquiry sizes
NPS 8 – 12 Sch 10S / 40S; confirm SML vs WLD on enquiry
NPS 14 – 24 Sch 10S / 40S; often mill-order depending on wall and route
Special OD × wall By agreement — state OD, wall (nominal or minimum), and length practice

Special OD×wall, non-standard lengths, and mixed SML/WLD packages are routine on enquiry. Send NPS or OD × wall, schedule or minimum wall, manufacturing type, and quantity, and we will answer with what can ship from selected stock versus what needs a mill slot.

Equivalent Grades

Equivalent designations help sourcing, but they do not replace the ASTM A312 grade line on the purchase order. The table below lists the primary ASTM identity for TP316N, the separate ASME twin, and the most common commercial or EN cross-references we see on enquiries.

Designation Notes
ASTM A312 TP316N / UNS S31651 Governing product specification on this page
ASME SA-312 TP316N / S31651 Separate Code Book twin — dual-mark only when PO names both
UNS S31651 Unified numbering identity on MTC and stencil

Compare A312 TP316LN when the project needs low carbon with nitrogen, and A312 TP316 when the ordinary 75/30 ksi floor is enough. The UNS number prevents those three from collapsing into one “316N” nickname on the receiving dock.

Heat Treatment and Delivery Condition

UNS S31651 is not individually listed in Table 2, so the default solution anneal at 1900 °F [1040 °C] minimum with rapid cooling applies. TP316N is not an H grade: there is no Table 5 grain-size requirement and no mandatory carbon floor at 0.04%. The nitrogen band and the 80/35 ksi tensile row are what distinguish the release, not a creep-oriented heat-treatment package.

State the anneal and cooling method on the MTC. Supplementary corrosion or product-analysis tests are separate line items and should not be assumed from the anneal alone.

Corrosion Resistance

With Mo 2–3%, TP316N gives broadly the same pitting and crevice behaviour as TP316 in chloride-bearing process streams; the nitrogen is there mainly for strength. A312 does not provide a corrosion table, so treat this paragraph as engineering commentary and validate against the project’s corrosion engineer and any Supplementary S7/S9 testing that was ordered.

It is important not to read the higher tensile floor as improved corrosion resistance. If welded aqueous service and sensitization control are the drivers, A312 TP316LN or A312 TP316L are the clearer ASTM A312 choices.

Applications of ASTM A312 TP316N Pipe

Buyers specify ASTM A312 TP316N when the process needs Mo-bearing 316 chemistry and a higher room-temperature yield floor than TP316. Typical placements are listed below.

Application Why TP316N Buyer note
Pressure piping needing a higher yield floor than TP316 80/35 ksi Table 4 row Confirm code allowables for S31651
Mo-bearing process lines where wall weight matters N strengthening with Mo 2–3% Check code minimum wall before down-gauging
Mechanical and structural stainless lines Higher yield than standard 316 Compare TP316LN if low carbon is needed

If the datasheet lists more than one 316-family option, walk the chemistry and tensile rows on this page against the sister ASTM A312 grades before freezing the PO. A wrong sister grade is harder to untangle after the pipe is bevelled and welded into the rack.

Weldability

Table 6 maps TP316N to the ER316 family, and that class should be frozen on the WPS and PQR before production welding. Nitrogen in the base metal affects weld-metal strength and dilution, so procedure qualification should use TP316N coupons rather than ordinary TP316 leftover.

If the service is aqueous and sensitization-sensitive, reconsider whether TP316N was the right base-metal choice before inventing a low-carbon weld overlay as a workaround—changing to A312 TP316LN upstream is cleaner than fighting chemistry in the weld.

Surface Finishes

Surface condition for ASTM A312 TP316N pipe should be stated on the purchase order rather than left to mill default. For stainless pipe, embedded free iron, residual scale, and chloride contamination from handling can matter as much as the nominal finish name, especially on aqueous or clean-process lines.

  • Annealed and pickled — the usual delivery for process piping after solution treatment
  • Blasted and pickled — when scale removal needs a mechanical assist before passivation
  • Bright annealed — by agreement for selected sizes and routes
  • Polished (OD/ID) — grit or Ra target by agreement; state which surface is polished

Export orders should also say how ends are protected and whether chlorine-bearing labels or cards are banned from contact with the bore. Those handling notes prevent avoidable rejection at receiving without changing the A312 metallurgical release.

Inspection and Testing

The base acceptance package for ASTM A312 TP316N pipe combines chemistry, tensile testing, heat-treatment evidence, and a pressure or electrical integrity test on every length. Flattening or bend tests apply per the manufacturing type and size rules in the referenced edition. Require nitrogen on every heat next to the 80/35 ksi tensile results.

Supplementary requirements are optional until written on the order. The options buyers request most often for this grade are summarized below.

Option Purpose
S1 product analysis Confirms chemistry on finished pipe
S5 radiography Weld integrity on WLD pipe
S7 intergranular corrosion A262 Practice E after sensitizing treatment
S8 minimum wall Wall interpreted as minimum rather than nominal
S9 weld decay Compares weld and base-metal loss rates

EN 10204 3.1 certification is our standard document set; 3.2 third-party inspection is arranged when the enquiry names the agency and hold points. Hydrostatic versus NDE selection belongs on the PO—silent mill option is not the same as an approved project method.

Packaging and Shipping

Export and domestic shipments of ASTM A312 TP316N pipe are packed for handling and for ocean or land transport. Each length is marked with ASTM A312 (and SA-312 when dual-certified), TP316N / UNS S31651, the manufacturing type, size, heat number, and test method. Bundle or crate lists should repeat the heat numbers so receiving can match pipe to certificates without opening every wrap.

  • Ends capped or bevelled and protected as ordered
  • Bundles strapped with stainless or protected contact points to limit iron contamination
  • Waterproof wrapping for ocean freight when specified
  • Packing list with heat numbers, sizes, and certificate references

Special marking (colour codes, project tag numbers, or bilingual stencils) is available on confirmed orders. Tell us the destination and handling limits early so packing matches the lift plan without repacking at the port.

Why Choose SHH STEEL

SHH STEEL supplies specification-driven stainless plate and pipe, and for ASTM A312 TP316N we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 chemistry, the Table 4 tensile results, and the heat-treatment evidence the grade requires, then match manufacturing type and size to the enquiry instead of pushing a one-size stock answer.

  • 80/35 ksi Table 4 release with mandatory N 0.10–0.16% on the certificate
  • Clear comparison to TP316 and TP316LN so strength is not confused with low-carbon intent
  • ER316 family filler guidance frozen on the enquiry when welding is in scope
  • SML, WLD, and HCW routes with EN 10204 3.1 MTCs; 3.2 inspection on request
  • Dual A312/SA-312 marking only when the purchase order asks for both editions
  • Project packing, cut lengths, and beveling coordinated on confirmed orders

If you are still choosing among 316-family ASTM A312 grades, send the design temperature, welded vs seamless preference, and any EN dual-mark need—we will answer with the grade that actually fits rather than the one that is merely closest in name.

Supply Capability

SHH STEEL can supply ASTM A312 TP316N stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.

Item SHH STEEL capability for TP316N
Standard ASTM A312 / A312M TP316N / UNS S31651
Manufacturing types SML, WLD, HCW
Size NPS 1/8 and up per ASME B36.19; special OD/wall by agreement
Schedules 5S, 10S, 40S, 80S and non-standard walls
Length SRL, DRL, or cut-to-length
Finish Annealed and pickled; blasted and pickled; bright annealed or polished by agreement
Filler guidance ER316 (Table 6 family listing)
Testing Tension (80/35 ksi), flattening/bend, hydro or NDE per length; C ≤0.08% and N 0.10–0.16% on MTC; 1900 °F default anneal stated; S1/S5/S7/S8/S9 on order
Documents EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Stock / Available sizes. Representative stockable and mill-enquiry sizes for TP316N are listed in the Dimensions section (NPS 1/2–24 with Sch 10S/40S/80S as typical). Selected common OD×wall combinations may be available from stock; heavy-wall seamless, unusual schedules, and special cut lengths are normally mill-order. We do not invent warehouse SKUs or tonnage claims—ask for a live check against your size list.

Enquiries should state the A312 edition, TP316N (UNS S31651), SML/WLD/HCW, NPS or OD × wall (and whether wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements, so mill slots line up with your need date. Dual SA-312 marking, cut lengths, beveling, and packing-list marking are available on confirmed orders.

FAQ

Is ASTM A312 the same as ASME SA-312 for TP316N?
ASTM A312/A312M and ASME SA-312/SA-312M of a referenced edition are technically aligned on Table 1 chemistry, Table 4 tensile, manufacturing types and most testing language, but they remain two independent standards. Dual A312/SA-312 marking is available when the purchase order names both editions and the heat qualifies under each, so write both on the PO rather than treating the titles as synonyms.
What is the UNS number for ASTM A312 TP316N?
TP316N is UNS S31651. Put that identifier on the MTC next to the 0.10–0.16% nitrogen result and the 80/35 ksi tensile row, so receiving inspectors can verify the strength claim against the chemistry rather than relying on a “316N” nickname.
TP316N vs TP316 — which should I order?
Order TP316N when you need the 80/35 ksi Table 4 floor and can accept C ≤0.08% with mandatory nitrogen. Order A312 TP316 when the ordinary 75/30 ksi floor is enough. Confirm code allowables for S31651 before thinning the wall on strength grounds.
TP316N vs TP316LN — what is the difference?
Same nitrogen band, different carbon and tensile rows: TP316N allows C ≤0.08% and releases at 80/35 ksi, while A312 TP316LN caps C at 0.035% and releases at 75/30 ksi. Choose N for strength and LN for low-carbon welded aqueous service.
Seamless vs welded TP316N pipe — which is better?
Seamless is preferred for high-pressure, thick-wall or owner specifications that exclude welded pipe. Welded and HCW routes are fully valid under ASTM A312 when the strip or plate heat carries the full TP316N chemistry and the inspection plan matches the design class, so choose the route from the code and wall schedule rather than habit.
Hydrostatic test vs NDE — which do I get on TP316N pipe?
Each length is hydrostatically tested or nondestructively electrically tested, and the manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification locks one method, state it on the PO and check that the chosen test appears on the MTC for every length, because a silent mill option is not an approved project method.
What heat treatment applies to TP316N?
UNS S31651 is not individually listed in Table 2, so the default solution anneal at 1900 °F [1040 °C] minimum with rapid cooling applies. TP316N is not an H grade and has no Table 5 grain-size requirement, so do not expect an H-grade release package.
What Table 1 chemistry defines TP316N?
Table 1 requires C ≤0.08%, Mn ≤2.00, P ≤0.045, S ≤0.030, Si ≤1.00, Cr 16.0–18.0, Ni 10.0–14.0, Mo 2.00–3.00 and N 0.10–0.16%. Product analysis follows A480 A1.1, and nitrogen must be reported on every heat.
Why are the tensile minima higher for TP316N?
The mandatory 0.10–0.16% nitrogen strengthens the austenitic matrix enough for A312 to write the 80/35 ksi floor with 35% L / 25% T elongation. It is not because chromium, nickel or molybdenum moved outside the ordinary 316 bands, so chemistry and tensile must be read together.
What filler metal is used to weld TP316N pipe?
Table 6 maps TP316N to the ER316 family. Freeze that class on the WPS and qualify on TP316N coupons rather than leftover TP316, because nitrogen in the base metal affects dilution and weld-metal strength across the joint.
Is TP316N an H grade for creep service?
No. TP316N has no Table 5 grain-size control and no 0.04% carbon floor. For the H package under ASTM A312, look at A312 TP316H; using TP316N as a creep substitute because of its higher room-temperature tensile row is a specification error.

Conclusion

ASTM A312 TP316N / UNS S31651 is nitrogen-strengthened 316 pipe: C ≤0.08%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00% and N 0.10–0.16%, released at 80/35 ksi with 35% L / 25% T elongation after a default 1900 °F [1040 °C] anneal. It is not an H grade and not a drop-in for A312 TP316LN. Put the manufacturing type, size and wall, finish and grade-specific chemistry evidence on the purchase order, then review the EN 10204 3.1 MTC before release. SHH STEEL can supply ASTM A312 TP316N pipe to the edition you name; browse sister grades on the A312/A312M hub, or send your size list to admin@steelspecs.com.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X