ASTM A312 TP316LN Stainless Steel Pipe
What is ASTM A312 TP316LN Stainless Steel Pipe
ASTM A312/A312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. It is an ASTM product specification in its own right; ASME SA-312 is a separate Code Book adoption of related text, and the two should not be treated as interchangeable titles on a purchase order. This page is written against A312/A312M for TP316LN / UNS S31653, with numbers taken from the referenced A312/A312M tables.
Within that scope, TP316LN / UNS S31653 is the low-carbon, nitrogen-bearing 316 grade for welded aqueous service. Table 1 caps carbon at 0.035% and requires nitrogen in the 0.10–0.16% band, with Cr 16.0–18.0%, Ni 10.0–14.0%, and Mo 2.00–3.00%. The low carbon limits sensitization in weld heat-affected zones, while the nitrogen stabilizes austenite without pushing the grade onto the TP316N 80/35 ksi tensile row. Table 4 releases TP316LN at 75 ksi [515 MPa] tensile / 30 ksi [205 MPa] yield with 35% L / 25% T elongation. UNS S31653 is not individually listed in Table 2, so the default solution anneal at 1900 °F [1040 °C] minimum with rapid cooling applies, and TP316LN is not an H grade.
SHH STEEL can supply ASTM A312 TP316LN stainless steel pipe as seamless (SML), welded (WLD), or heavily cold-worked (HCW) product in ASME B36.19 schedules and special OD/wall combinations, with EN 10204 3.1 mill test certificates as standard and third-party 3.2 inspection when the enquiry asks for it. Dual A312/SA-312 marking is available only when the purchase order names both editions and the mill heat qualifies under each—do not assume a single stamp covers Code stamping without that instruction. For the separate ASME-framed page on the same grade, see SA312 TP316LN.
Buyers searching “316LN pipe,” “S31653,” or “low-carbon nitrogen 316” are usually looking for this row. Confirm that the MTC reports both C ≤0.035% and N in the 0.10–0.16% band—nitrogen alone does not make a heat into TP316LN if carbon sits at the ordinary TP316 ceiling, and a TP316L heat without the nitrogen floor is a different grade even when Mo matches.
Within the ASTM A312 series, buyers comparing TP316LN usually look next at A312 TP316L, A312 TP316N, A312 TP316, A312 TP304LN, and A312 TP316H. Browse the full grade list on the A312/A312M hub when the datasheet leaves more than one 316-family option open.
Manufacturing Types (SML / WLD / HCW)
ASTM A312 recognizes three manufacturing routes for TP316LN pipe, and the route is a purchase-order decision driven by the design code, the size range, wall thickness, and how the owner wants the pipe inspected. The route never changes the chemistry: whichever way the pipe is made, the heat must still meet C ≤0.035%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00%, and N 0.10–0.16%, and every length must still go through the solution anneal at 1900 °F [1040 °C] minimum before it is released.
- Seamless (SML) — no welding at any stage. Preferred for high-pressure service, thick walls, and owners who exclude welded pipe from the design class. Welded aqueous lines frequently accept WLD pipe when the strip heat carries the full TP316LN chemistry and the low-carbon consumable is frozen on the WPS.
- Welded (WLD) — automatic welding without filler metal, with the weld finished so the pipe meets dimensional and mechanical requirements after the final heat treatment. The strip or plate heat must itself carry the full TP316LN chemistry, so ask for the coil or plate heat number on the certificate.
- Heavily cold-worked (HCW) — welded pipe cold worked to at least 35% reduction of wall and weld before the final anneal, again without filler in the longitudinal seam, with the weld radiographed before cold work. Order HCW when the project specifically wants that marking and the process controls A312 writes around it.
Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test in place of the hydrotest, and lots for mechanical testing follow the sampling clauses in the referenced edition. State SML, WLD, or HCW on the enquiry so mill slots and test plans line up before the heat is poured.
Chemical Composition of ASTM A312 TP316LN
Chemistry for ASTM A312 TP316LN has two checkpoints. Melting analysis under Table 1 is mandatory on every heat, and product analysis under A480 A1.1 applies when S1 is written on the order. The grade is defined by the combination of C ≤0.035% and N 0.10–0.16% with Mo 2.00–3.00%; missing nitrogen on the MTC is as serious as missing the low-carbon ceiling.
Table 1 melting limits for TP316LN / UNS S31653 are summarized below. Values are maximum unless a range is shown.
| Element | TP316LN / UNS S31653 melting analysis |
|---|---|
| Carbon (C) | ≤ 0.035 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 16.0 – 18.0 |
| Nickel (Ni) | 10.0 – 14.0 |
| Molybdenum (Mo) | 2.00 – 3.00 |
| Nitrogen (N) | 0.10 – 0.16 |
Product-analysis limits after A480 A1.1 tolerances are listed next. Nitrogen’s 0.01 under/over tolerance moves the product window to 0.09–0.17%, while carbon may reach 0.045% on product analysis only after the heat itself met ≤0.035%.
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.035 | 0.01 over | ≤ 0.045 |
| Manganese (Mn) | ≤ 2.00 | 0.04 over | ≤ 2.04 |
| Phosphorus (P) | ≤ 0.045 | 0.010 over | ≤ 0.055 |
| Sulfur (S) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Silicon (Si) | ≤ 1.00 | 0.05 over | ≤ 1.05 |
| Chromium (Cr) | 16.0 – 18.0 | 0.20 under / over | 15.80 – 18.20 |
| Nickel (Ni) | 10.0 – 14.0 | 0.15 under / over | 9.85 – 14.15 |
| Molybdenum (Mo) | 2.00 – 3.00 | 0.10 under / over | 1.90 – 3.10 |
| Nitrogen (N) | 0.10 – 0.16 | 0.01 under / over | 0.09 – 0.17 |
Small-diameter or light-wall footnotes in some A312 editions can adjust the carbon story for certain sizes—confirm whether footnote D (or its successor) applies to your NPS and wall before accepting a borderline carbon result. When in doubt, name the edition and the footnote on the PO.
Mechanical Properties of ASTM A312 TP316LN
Table 4 sets the room-temperature tensile floor for ASTM A312 TP316LN at the values below. They are lot minima for release, not design allowables. Note that TP316LN shares the 75/30 ksi row with TP316L and TP316 despite the nitrogen addition—nitrogen here stabilizes austenite under a low-carbon ceiling rather than buying the TP316N strength bump.
| Property | TP316LN |
|---|---|
| Tensile, min | 75 ksi [515 MPa] |
| Yield, min | 30 ksi [205 MPa] |
| Elongation | 35% L / 25% T |
Two ordering mistakes show up often: treating TP316LN as if it carried the 80/35 ksi TP316N floor, and treating a TP316L heat without reported nitrogen as “close enough.” Neither reading matches Table 1 or Table 4. Write UNS S31653 and the N band on the enquiry when the datasheet depends on them.
Dimensions, Tolerances and Stock Sizes
Dimensional supply for ASTM A312 TP316LN pipe follows ASME B36.19 schedules for the common NPS and schedule combinations, with special OD and wall available by agreement when a project needs a section the schedules do not cover. Outside-diameter variations follow ASTM A999/A999M, and wall-thickness variations follow A312 Table 3 as summarized below. State on the purchase order whether wall is nominal or minimum (Supplementary S8), because the two readings produce different pipe from the same size line.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
- Lengths — single random, double random, or cut-to-length on order
- Cut lengths — typically no more than 1/4 in. [6 mm] over the ordered length unless the PO states a tighter band
- Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen
Welded aqueous skids often run Sch 10S and 40S; confirm that light-wall sizes still meet the project’s corrosion allowance after the 12.5% under-tolerance. Straightness, end finish, and length tolerance should be written into export orders so receiving inspection has an agreed acceptance basis instead of arguing after arrival. Jointers are not permitted unless the purchase order allows them, so cut-to-length programmes should include an allowance for fit-up scrap rather than expecting the mill to ship short pieces.
Stock / Available sizes. SHH STEEL quotes TP316LN against a practical stock-and-mill enquiry range rather than a frozen warehouse SKU list. The representative sizes below are the combinations we most often discuss for ASTM A312 TP316LN; availability by manufacturing type and exact wall still has to be confirmed on enquiry, and we do not publish fake tonnages against individual lines.
| Representative size | Typical schedules / notes |
|---|---|
| NPS 1/2 – 2 | Sch 10S / 40S / 80S; common process take-offs |
| NPS 2-1/2 – 6 | Sch 10S / 40S / 80S; frequent mill and stock enquiry sizes |
| NPS 8 – 12 | Sch 10S / 40S; confirm SML vs WLD on enquiry |
| NPS 14 – 24 | Sch 10S / 40S; often mill-order depending on wall and route |
| Special OD × wall | By agreement — state OD, wall (nominal or minimum), and length practice |
Special OD×wall, non-standard lengths, and mixed SML/WLD packages are routine on enquiry. Send NPS or OD × wall, schedule or minimum wall, manufacturing type, and quantity, and we will answer with what can ship from selected stock versus what needs a mill slot.
Equivalent Grades
Equivalent designations help sourcing, but they do not replace the ASTM A312 grade line on the purchase order. The table below lists the primary ASTM identity for TP316LN, the separate ASME twin, and the most common commercial or EN cross-references we see on enquiries.
| Designation | Notes |
|---|---|
| ASTM A312 TP316LN / UNS S31653 | Governing product specification on this page |
| ASME SA-312 TP316LN / S31653 | Separate Code Book twin — dual-mark only when PO names both |
| UNS S31653 | Unified numbering identity on MTC and stencil |
Keep UNS S31653 on the stencil even when the commercial name is simply “316LN.” Sister low-carbon grades such as A312 TP316L share the carbon story but not the nitrogen floor.
Heat Treatment and Delivery Condition
UNS S31653 is not individually listed in Table 2, so the default solution-annealing practice applies: heat to a minimum of 1900 °F [1040 °C] and cool rapidly in water or by other rapid means. TP316LN is not an H grade, so Table 5 grain-size control and the H-grade reheat/lot-marking package do not automatically apply.
Most aqueous-service orders ship annealed and pickled. If the project needs a bright-annealed or mechanically polished bore, say so on the enquiry—those finishes are order extras, not mill defaults for every size.
Corrosion Resistance
A312 does not publish a corrosion-rate table, so the notes here are commentary. Low carbon is the primary control for intergranular attack in weld heat-affected zones, which is why TP316LN is chosen for welded aqueous and chemical service. Mo 2–3% supports pitting and crevice resistance in the same family as TP316L, while the 0.10–0.16% nitrogen helps keep the structure fully austenitic under the low-carbon ceiling.
Nitrogen is not a licence to ignore surface finish or chlorides. Pickling, passivation, and chloride limits in the process stream still dominate field performance. If the project needs the higher 80/35 ksi floor more than the low-carbon ceiling, compare A312 TP316N rather than assuming LN and N are interchangeable.
Applications of ASTM A312 TP316LN Pipe
ASTM A312 TP316LN shows up where welded aqueous or chemical piping needs low carbon and a stable austenitic structure with Mo. The application table below is a buyer-oriented summary, not a code approval list.
| Application | Why TP316LN | Buyer note |
|---|---|---|
| Welded aqueous and chemical process piping | C ≤0.035% limits HAZ sensitization | Qualify WPS on TP316LN |
| Lines needing stable austenite with low carbon | N 0.10–0.16% with Mo 2–3% | Released at 75/30 ksi, not 80/35 |
| Projects specifying 316LN by datasheet | UNS S31653 identity on MTC | Report N on every heat |
If the datasheet lists more than one 316-family option, walk the chemistry and tensile rows on this page against the sister ASTM A312 grades before freezing the PO. A wrong sister grade is harder to untangle after the pipe is bevelled and welded into the rack.
Weldability
Table 6 maps TP316LN to the ER316L family, and a low-carbon consumable should be frozen on the WPS. Avoid ER316H or higher-carbon fillers for aqueous LN service unless engineering explicitly approves the mismatch and documents why the deposit carbon is acceptable.
Because the base metal already carries 0.10–0.16% N, discuss dilution and ferrite balance with the welding engineer when the joint is heavily constrained. The goal is still a low-carbon deposit that matches the LN corrosion intent, not a high-strength overlay.
Surface Finishes
Surface condition for ASTM A312 TP316LN pipe should be stated on the purchase order rather than left to mill default. For stainless pipe, embedded free iron, residual scale, and chloride contamination from handling can matter as much as the nominal finish name, especially on aqueous or clean-process lines.
- Annealed and pickled — the usual delivery for process piping after solution treatment
- Blasted and pickled — when scale removal needs a mechanical assist before passivation
- Bright annealed — by agreement for selected sizes and routes
- Polished (OD/ID) — grit or Ra target by agreement; state which surface is polished
Export orders should also say how ends are protected and whether chlorine-bearing labels or cards are banned from contact with the bore. Those handling notes prevent avoidable rejection at receiving without changing the A312 metallurgical release.
Inspection and Testing
The base acceptance package for ASTM A312 TP316LN pipe combines chemistry, tensile testing, heat-treatment evidence, and a pressure or electrical integrity test on every length. Flattening or bend tests apply per the manufacturing type and size rules in the referenced edition. Require nitrogen and carbon both printed on every heat; S7 is common on aqueous welded service.
Supplementary requirements are optional until written on the order. The options buyers request most often for this grade are summarized below.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms chemistry on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S8 minimum wall | Wall interpreted as minimum rather than nominal |
| S9 weld decay | Compares weld and base-metal loss rates |
EN 10204 3.1 certification is our standard document set; 3.2 third-party inspection is arranged when the enquiry names the agency and hold points. Hydrostatic versus NDE selection belongs on the PO—silent mill option is not the same as an approved project method.
Packaging and Shipping
Export and domestic shipments of ASTM A312 TP316LN pipe are packed for handling and for ocean or land transport. Each length is marked with ASTM A312 (and SA-312 when dual-certified), TP316LN / UNS S31653, the manufacturing type, size, heat number, and test method. Bundle or crate lists should repeat the heat numbers so receiving can match pipe to certificates without opening every wrap.
- Ends capped or bevelled and protected as ordered
- Bundles strapped with stainless or protected contact points to limit iron contamination
- Waterproof wrapping for ocean freight when specified
- Packing list with heat numbers, sizes, and certificate references
Special marking (colour codes, project tag numbers, or bilingual stencils) is available on confirmed orders. Tell us the destination and handling limits early so packing matches the lift plan without repacking at the port.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless plate and pipe, and for ASTM A312 TP316LN we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 chemistry, the Table 4 tensile results, and the heat-treatment evidence the grade requires, then match manufacturing type and size to the enquiry instead of pushing a one-size stock answer.
- Low-carbon + nitrogen reporting on every heat (C ≤0.035%, N 0.10–0.16%)
- Honest distinction from TP316L (no N floor) and TP316N (80/35 ksi row)
- ER316L family filler guidance for aqueous welded service
- SML, WLD, and HCW routes with EN 10204 3.1 MTCs; 3.2 inspection on request
- Dual A312/SA-312 marking only when the purchase order asks for both editions
- Project packing, cut lengths, and beveling coordinated on confirmed orders
If you are still choosing among 316-family ASTM A312 grades, send the design temperature, welded vs seamless preference, and any EN dual-mark need—we will answer with the grade that actually fits rather than the one that is merely closest in name.
Supply Capability
SHH STEEL can supply ASTM A312 TP316LN stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.
| Item | SHH STEEL capability for TP316LN |
|---|---|
| Standard | ASTM A312 / A312M TP316LN / UNS S31653 |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD/wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | SRL, DRL, or cut-to-length |
| Finish | Annealed and pickled; blasted and pickled; bright annealed or polished by agreement |
| Filler guidance | ER316L (Table 6 family listing) |
| Testing | Tension (75/30 ksi), flattening/bend, hydro or NDE per length; C ≤0.035% and N 0.10–0.16% on MTC; 1900 °F default anneal stated; S1/S5/S7/S8/S9 on order |
| Documents | EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
Stock / Available sizes. Representative stockable and mill-enquiry sizes for TP316LN are listed in the Dimensions section (NPS 1/2–24 with Sch 10S/40S/80S as typical). Selected common OD×wall combinations may be available from stock; heavy-wall seamless, unusual schedules, and special cut lengths are normally mill-order. We do not invent warehouse SKUs or tonnage claims—ask for a live check against your size list.
Enquiries should state the A312 edition, TP316LN (UNS S31653), SML/WLD/HCW, NPS or OD × wall (and whether wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements, so mill slots line up with your need date. Dual SA-312 marking, cut lengths, beveling, and packing-list marking are available on confirmed orders.
FAQ
-
Is ASTM A312 the same as ASME SA-312 for TP316LN?
- ASTM A312/A312M and ASME SA-312/SA-312M of a referenced edition are technically aligned on Table 1 chemistry, Table 4 tensile, manufacturing types and most testing language, but they remain two independent standards. Dual A312/SA-312 marking is available when the purchase order names both editions and the heat qualifies under each, so write both on the PO rather than treating the titles as synonyms.
-
What is the UNS number for ASTM A312 TP316LN?
- TP316LN is UNS S31653. Keep that number on the MTC and stencil, because commercial “316LN” labels without S31653 and without a reported nitrogen value often hide ordinary TP316L heats that never met the 0.10–0.16% nitrogen floor.
-
TP316LN vs TP316L — which should I order?
- Both keep carbon low for welded aqueous service. TP316LN additionally requires N 0.10–0.16% and stays on the 75/30 ksi row, while A312 TP316L does not mandate that nitrogen band. Order LN when the datasheet or an austenite-stability note calls for nitrogen together with low carbon.
-
TP316LN vs TP316N — what is the difference?
- A312 TP316N allows C ≤0.08% and releases at 80/35 ksi. TP316LN caps C at 0.035% and releases at 75/30 ksi. They share the nitrogen band but tell different carbon and tensile stories, so do not swap them to chase strength or sensitization control alone.
-
Seamless vs welded TP316LN pipe — which is better?
- Seamless is preferred for high-pressure, thick-wall or owner specifications that exclude welded pipe. Welded and HCW routes are fully valid under ASTM A312 when the strip or plate heat carries the full TP316LN chemistry and the inspection plan matches the design class, so choose the route from the code and wall schedule rather than habit.
-
Hydrostatic test vs NDE — which do I get on TP316LN pipe?
- Each length is hydrostatically tested or nondestructively electrically tested, and the manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification locks one method, state it on the PO and check that the chosen test appears on the MTC for every length, because a silent mill option is not an approved project method.
-
What heat treatment applies to TP316LN?
- UNS S31653 is not individually listed in Table 2, so the default solution anneal at 1900 °F [1040 °C] minimum with rapid cooling applies. TP316LN is not an H grade and does not carry Table 5 grain-size control or the H-grade lot rules by default.
-
What Table 1 chemistry defines TP316LN?
- Table 1 requires C ≤0.035%, Mn ≤2.00, P ≤0.045, S ≤0.030, Si ≤1.00, Cr 16.0–18.0, Ni 10.0–14.0, Mo 2.00–3.00 and N 0.10–0.16%. Product analysis uses A480 A1.1 tolerances, and any small-OD carbon footnote should be checked against the ordered edition.
-
What are the tensile requirements for ASTM A312 TP316LN?
- Table 4 sets 75 ksi [515 MPa] tensile / 30 ksi [205 MPa] yield with 35% L / 25% T elongation. That is the same floor as TP316L, not the TP316N 80/35 ksi row, so the nitrogen in LN should not be read as a silent upgrade to N-grade tensile minima on the purchase order.
-
What filler metal is used to weld TP316LN pipe?
- Table 6 maps TP316LN to the ER316L family. Freeze a low-carbon consumable on the WPS and avoid ER316H for aqueous LN service unless engineering documents an approved exception and explains why the higher deposit carbon is acceptable.
-
Why specify nitrogen in TP316LN?
- Nitrogen at 0.10–0.16% helps stabilize austenite under the low-carbon ceiling without moving the grade onto the TP316N tensile row. It must appear on every heat’s MTC; missing nitrogen means the heat is not TP316LN even when carbon and molybdenum look right.
Conclusion
ASTM A312 TP316LN / UNS S31653 is low-carbon, nitrogen-bearing 316 pipe: C ≤0.035%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00% and N 0.10–0.16%, released at 75/30 ksi with 35% L / 25% T elongation after a default 1900 °F [1040 °C] anneal. It is not a drop-in for A312 TP316N. Put the manufacturing type, size and wall, finish and grade-specific chemistry evidence on the purchase order, then review the EN 10204 3.1 MTC before release. SHH STEEL can supply ASTM A312 TP316LN pipe to the edition you name; browse sister grades on the A312/A312M hub, or send your size list to admin@steelspecs.com.