ASTM A312 TP316H Stainless Steel Pipe
What is ASTM A312 TP316H Stainless Steel Pipe
ASTM A312/A312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. It is an ASTM product specification in its own right; ASME SA-312 is a separate Code Book adoption of related text, and the two should not be treated as interchangeable titles on a purchase order. This page is written against A312/A312M for TP316H / UNS S31609, with numbers taken from the referenced A312/A312M tables.
Within that scope, TP316H / UNS S31609 is the high-temperature H-grade member of the 316 family. Table 1 sets a controlled carbon band of 0.04–0.10% together with Cr 16.0–18.0%, Ni 10.0–14.0%, and Mo 2.00–3.00%, and Table 5 requires an ASTM grain size of No. 7 or coarser so the heat keeps high-temperature strength. Table 4 releases the grade at 75 ksi [515 MPa] tensile / 30 ksi [205 MPa] yield with 35% L / 25% T elongation, and Table 2 lists the solution anneal with TP304H at 1900 °F [1040 °C] minimum followed by rapid cooling. Clause 6.2 reheat rules and clause 17 lot marking travel with the H package, so the purchase order should name the carbon band, grain-size requirement, and heat-treatment lot rather than a bare “316H” stamp.
SHH STEEL can supply ASTM A312 TP316H stainless steel pipe as seamless (SML), welded (WLD), or heavily cold-worked (HCW) product in ASME B36.19 schedules and special OD/wall combinations, with EN 10204 3.1 mill test certificates as standard and third-party 3.2 inspection when the enquiry asks for it. Dual A312/SA-312 marking is available only when the purchase order names both editions and the mill heat qualifies under each—do not assume a single stamp covers Code stamping without that instruction. For the separate ASME-framed page on the same grade, see SA312 TP316H.
Commercial buyers often meet this chemistry under the names 316H, S31609, or “H-grade 316 pipe.” Those labels only stick when the MTC shows the 0.04–0.10% carbon band, the Table 5 grain size, and the 1900 °F [1040 °C] anneal. A dual TP316/TP316H heat is possible when carbon lands in the 0.04–0.08% overlap and grain size is controlled, but that dual mark has to be written on the order—do not assume a plain TP316 heat automatically qualifies as TP316H.
Within the ASTM A312 series, buyers comparing TP316H usually look next at A312 TP316, A312 TP316L, A312 TP316TI, A312 TP316N, and A312 TP304H. Browse the full grade list on the A312/A312M hub when the datasheet leaves more than one 316-family option open.
Manufacturing Types (SML / WLD / HCW)
ASTM A312 recognizes three manufacturing routes for TP316H pipe, and the route is a purchase-order decision driven by the design code, the size range, wall thickness, and how the owner wants the pipe inspected. The route never changes the chemistry: whichever way the pipe is made, the heat must still meet C 0.04–0.10%, Cr 16.0–18.0%, Ni 10.0–14.0%, and Mo 2.00–3.00%, and every length must still go through the solution anneal at 1900 °F [1040 °C] minimum before it is released.
- Seamless (SML) — no welding at any stage. Preferred for high-pressure service, thick walls, and owners who exclude welded pipe from the design class. For H-grade service, seamless is often preferred on thick walls and creep-critical heater loops, but welded and HCW routes remain valid when the WPS and inspection plan match the design class.
- Welded (WLD) — automatic welding without filler metal, with the weld finished so the pipe meets dimensional and mechanical requirements after the final heat treatment. The strip or plate heat must itself carry the full TP316H chemistry, so ask for the coil or plate heat number on the certificate.
- Heavily cold-worked (HCW) — welded pipe cold worked to at least 35% reduction of wall and weld before the final anneal, again without filler in the longitudinal seam, with the weld radiographed before cold work. Order HCW when the project specifically wants that marking and the process controls A312 writes around it.
Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test in place of the hydrotest, and lots for mechanical testing follow the sampling clauses in the referenced edition. State SML, WLD, or HCW on the enquiry so mill slots and test plans line up before the heat is poured.
Chemical Composition of ASTM A312 TP316H
Two chemistry layers matter for ASTM A312 TP316H. The melting (heat or ladle) analysis is mandatory for every heat under A312 Table 1, while product analysis on finished pipe applies the A480/A480M Annex A1.1 tolerances when Supplementary Requirement S1 is invoked. The controlled 0.04–0.10% carbon band is the H-grade signature; heats that land below 0.04% C fail TP316H even when Cr, Ni, and Mo sit inside the 316 family ranges.
The melting-analysis limits below are the release values the mill must meet on the heat. Read them as maxima unless a range is shown, and require every element on the MTC rather than a partial 316 summary.
| Element | TP316H / UNS S31609 melting analysis |
|---|---|
| Carbon (C) | 0.04 – 0.10 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 16.0 – 18.0 |
| Nickel (Ni) | 10.0 – 14.0 |
| Molybdenum (Mo) | 2.00 – 3.00 |
When product analysis is ordered, the A480 tolerances widen the acceptance window on finished pipe. The table below pairs each Table 1 limit with its A1.1 tolerance and the resulting product-analysis bound so receiving inspectors can check a check-analysis result without guessing.
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | 0.04 – 0.10 | 0.01 under / over | 0.03 – 0.11 |
| Manganese (Mn) | ≤ 2.00 | 0.04 over | ≤ 2.04 |
| Phosphorus (P) | ≤ 0.045 | 0.010 over | ≤ 0.055 |
| Sulfur (S) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Silicon (Si) | ≤ 1.00 | 0.05 over | ≤ 1.05 |
| Chromium (Cr) | 16.0 – 18.0 | 0.20 under / over | 15.80 – 18.20 |
| Nickel (Ni) | 10.0 – 14.0 | 0.15 under / over | 9.85 – 14.15 |
| Molybdenum (Mo) | 2.00 – 3.00 | 0.10 under / over | 1.90 – 3.10 |
Mechanical Properties of ASTM A312 TP316H
Room-temperature tensile requirements for ASTM A312 TP316H come from Table 4 and are summarized below. These are minimum release values for the lot, not typical mill values, and design allowables still come from the applicable code, not from this product page. The Table 5 grain-size row is part of the H package and should appear on the MTC with the tensile results.
| Property | TP316H |
|---|---|
| Tensile, min | 75 ksi [515 MPa] |
| Yield, min | 30 ksi [205 MPa] |
| Elongation | 35% L / 25% T |
| Grain size (Table 5) | No. 7 or coarser |
A heat that meets 75/30 ksi but fails grain size No. 7 or coarser is not TP316H under A312, even if carbon sits in the 0.04–0.10% band. Both checks travel together on a proper H-grade release.
Dimensions, Tolerances and Stock Sizes
Dimensional supply for ASTM A312 TP316H pipe follows ASME B36.19 schedules for the common NPS and schedule combinations, with special OD and wall available by agreement when a project needs a section the schedules do not cover. Outside-diameter variations follow ASTM A999/A999M, and wall-thickness variations follow A312 Table 3 as summarized below. State on the purchase order whether wall is nominal or minimum (Supplementary S8), because the two readings produce different pipe from the same size line.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
- Lengths — single random, double random, or cut-to-length on order
- Cut lengths — typically no more than 1/4 in. [6 mm] over the ordered length unless the PO states a tighter band
- Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen
On hot H-grade lines, settle nominal versus minimum wall (S8) early. Straightness, end finish, and length tolerance should be written into export orders so receiving inspection has an agreed acceptance basis instead of arguing after arrival. Jointers are not permitted unless the purchase order allows them, so cut-to-length programmes should include an allowance for fit-up scrap rather than expecting the mill to ship short pieces.
Stock / Available sizes. SHH STEEL quotes TP316H against a practical stock-and-mill enquiry range rather than a frozen warehouse SKU list. The representative sizes below are the combinations we most often discuss for ASTM A312 TP316H; availability by manufacturing type and exact wall still has to be confirmed on enquiry, and we do not publish fake tonnages against individual lines.
| Representative size | Typical schedules / notes |
|---|---|
| NPS 1/2 – 2 | Sch 10S / 40S / 80S; common process take-offs |
| NPS 2-1/2 – 6 | Sch 10S / 40S / 80S; frequent mill and stock enquiry sizes |
| NPS 8 – 12 | Sch 10S / 40S; confirm SML vs WLD on enquiry |
| NPS 14 – 24 | Sch 10S / 40S; often mill-order depending on wall and route |
| Special OD × wall | By agreement — state OD, wall (nominal or minimum), and length practice |
Special OD×wall, non-standard lengths, and mixed SML/WLD packages are routine on enquiry. Send NPS or OD × wall, schedule or minimum wall, manufacturing type, and quantity, and we will answer with what can ship from selected stock versus what needs a mill slot.
Equivalent Grades
Equivalent designations help sourcing, but they do not replace the ASTM A312 grade line on the purchase order. The table below lists the primary ASTM identity for TP316H, the separate ASME twin, and the most common commercial or EN cross-references we see on enquiries.
| Designation | Notes |
|---|---|
| ASTM A312 TP316H / UNS S31609 | Governing product specification on this page |
| ASME SA-312 TP316H / S31609 | Separate Code Book twin — dual-mark only when PO names both |
| EN 1.4919 (approx.) | Approximate high-temperature map; recheck C band and grain size |
EN 1.4919 is a soft cross-reference only; carbon band, Mo, and grain-size evidence on the A312 MTC still govern acceptance. Do not accept an EN dual stamp that skips Table 5 grain size when the order called for TP316H.
Heat Treatment and Delivery Condition
Table 2 lists TP316H with TP304H at 1900 °F [1040 °C] minimum for both cold-finished and hot-finished pipe, followed by rapid cooling. The hot-finished size notes in the right-hand columns of Table 2 should be read from the edition named on the order; this pack cites the 1900 °F listing with the TP304H group and does not invent additional size footnotes. Clause 6.2 reheat rules apply when pipe is reheated after the qualifying anneal, and clause 17 lot marking ties the heat-treatment lot to the stencil.
Delivery condition is normally solution-annealed and pickled unless the purchase order asks for bright annealing or another finish. Record the anneal temperature and cooling method on the MTC so inspectors can verify the H package without calling the mill after the pipe arrives.
Corrosion Resistance
ASTM A312 does not contain a corrosion table, so this section is engineering commentary rather than a specification requirement. TP316H carries the same Cr, Ni, and Mo as the rest of the 316 family, so its pitting and general corrosion behaviour in chloride-bearing media is broadly similar to TP316 at comparable temperature and surface condition. The H package exists for elevated-temperature strength and microstructural control, not because Mo was raised above the 2–3% band.
Do not substitute TP316L into a TP316H line on the argument that “low carbon corrodes better.” Low carbon helps intergranular resistance after welding, but it removes the carbon floor and grain-size package the hot design relied on. For aqueous welded service, look at A312 TP316L or A312 TP316LN instead of stretching an H-grade heat.
Applications of ASTM A312 TP316H Pipe
Applications for ASTM A312 TP316H pipe are driven by elevated design temperature combined with the moderate corrosion resistance of the 316 family. The table below summarizes where buyers typically place the grade; always confirm code allowables for UNS S31609 before final wall selection.
| Application | Why | Note |
|---|---|---|
| High-T process / heater tubes (creep) | H rules + Mo | Confirm S31609 allowables |
| Refinery / chemical hot lines | 316 oxidation + H | Do not substitute TP316L |
If the datasheet lists more than one 316-family option, walk the chemistry and tensile rows on this page against the sister ASTM A312 grades before freezing the PO. A wrong sister grade is harder to untangle after the pipe is bevelled and welded into the rack.
Weldability
Table 6 assigns ER316H as the filler for TP316H / UNS S31609, and that consumable should appear on the WPS and PQR. ER316H keeps a carbon level in the deposit that supports creep strength consistent with the H-grade base metal; swapping in ER316L for convenience undercuts the reason the pipe was ordered as TP316H.
Qualify the procedure on TP316H material, not on a convenient TP316 coupon, when the design temperature depends on the H package. Cleanliness, interpass temperature, and post-weld inspection should follow the project specification; A312 itself does not rewrite the fabrication code.
Surface Finishes
Surface condition for ASTM A312 TP316H pipe should be stated on the purchase order rather than left to mill default. For stainless pipe, embedded free iron, residual scale, and chloride contamination from handling can matter as much as the nominal finish name, especially on aqueous or clean-process lines.
- Annealed and pickled — the usual delivery for process piping after solution treatment
- Blasted and pickled — when scale removal needs a mechanical assist before passivation
- Bright annealed — by agreement for selected sizes and routes
- Polished (OD/ID) — grit or Ra target by agreement; state which surface is polished
Export orders should also say how ends are protected and whether chlorine-bearing labels or cards are banned from contact with the bore. Those handling notes prevent avoidable rejection at receiving without changing the A312 metallurgical release.
Inspection and Testing
The base acceptance package for ASTM A312 TP316H pipe combines chemistry, tensile testing, heat-treatment evidence, and a pressure or electrical integrity test on every length. Flattening or bend tests apply per the manufacturing type and size rules in the referenced edition. Include Table 5 grain size and the 0.04–0.10% C band on the same certificate line items as tensile.
Supplementary requirements are optional until written on the order. The options buyers request most often for this grade are summarized below.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms chemistry on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S8 minimum wall | Wall interpreted as minimum rather than nominal |
| S9 weld decay | Compares weld and base-metal loss rates |
EN 10204 3.1 certification is our standard document set; 3.2 third-party inspection is arranged when the enquiry names the agency and hold points. Hydrostatic versus NDE selection belongs on the PO—silent mill option is not the same as an approved project method.
Packaging and Shipping
Export and domestic shipments of ASTM A312 TP316H pipe are packed for handling and for ocean or land transport. Each length is marked with ASTM A312 (and SA-312 when dual-certified), TP316H / UNS S31609, the manufacturing type, size, heat number, and test method. Bundle or crate lists should repeat the heat numbers so receiving can match pipe to certificates without opening every wrap.
- Ends capped or bevelled and protected as ordered
- Bundles strapped with stainless or protected contact points to limit iron contamination
- Waterproof wrapping for ocean freight when specified
- Packing list with heat numbers, sizes, and certificate references
Special marking (colour codes, project tag numbers, or bilingual stencils) is available on confirmed orders. Tell us the destination and handling limits early so packing matches the lift plan without repacking at the port.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless plate and pipe, and for ASTM A312 TP316H we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 chemistry, the Table 4 tensile results, and the heat-treatment evidence the grade requires, then match manufacturing type and size to the enquiry instead of pushing a one-size stock answer.
- H-grade package control — C 0.04–0.10%, Table 5 grain size, and 1900 °F [1040 °C] anneal stated on the MTC
- Clear sister-grade advice when TP316, TP316L, or TP316Ti would actually fit the service better
- ER316H filler guidance aligned with Table 6 for WPS planning
- SML, WLD, and HCW routes with EN 10204 3.1 MTCs; 3.2 inspection on request
- Dual A312/SA-312 marking only when the purchase order asks for both editions
- Project packing, cut lengths, and beveling coordinated on confirmed orders
If you are still choosing among 316-family ASTM A312 grades, send the design temperature, welded vs seamless preference, and any EN dual-mark need—we will answer with the grade that actually fits rather than the one that is merely closest in name.
Supply Capability
SHH STEEL can supply ASTM A312 TP316H stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.
| Item | SHH STEEL capability for TP316H |
|---|---|
| Standard | ASTM A312 / A312M TP316H / UNS S31609 |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD/wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | SRL, DRL, or cut-to-length |
| Finish | Annealed and pickled; blasted and pickled; bright annealed or polished by agreement |
| Filler guidance | ER316H (Table 6) |
| Testing | Tension (75/30 ksi), Table 5 grain size No. 7 or coarser, flattening/bend, hydro or NDE per length; C 0.04–0.10% on MTC; 1900 °F anneal and clause 6.2 reheat stated; S1/S5/S7/S8/S9 on order |
| Documents | EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
Stock / Available sizes. Representative stockable and mill-enquiry sizes for TP316H are listed in the Dimensions section (NPS 1/2–24 with Sch 10S/40S/80S as typical). Selected common OD×wall combinations may be available from stock; heavy-wall seamless, unusual schedules, and special cut lengths are normally mill-order. We do not invent warehouse SKUs or tonnage claims—ask for a live check against your size list.
Enquiries should state the A312 edition, TP316H (UNS S31609), SML/WLD/HCW, NPS or OD × wall (and whether wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements, so mill slots line up with your need date. Dual SA-312 marking, cut lengths, beveling, and packing-list marking are available on confirmed orders.
FAQ
-
Is ASTM A312 the same as ASME SA-312 for TP316H?
- ASTM A312/A312M and ASME SA-312/SA-312M of a referenced edition are technically aligned on Table 1 chemistry, Table 4 tensile, manufacturing types and most testing language, but they remain two independent standards. Dual A312/SA-312 marking is available when the purchase order names both editions and the heat qualifies under each, so write both on the PO rather than treating the titles as synonyms.
-
What is the UNS number for ASTM A312 TP316H?
- TP316H is UNS S31609. That number should appear on the MTC and stencil together with the ASTM A312 grade mark, because a bare commercial “316H” nickname makes it harder to tie the carbon band and Table 5 grain-size evidence to the same heat during receiving inspection.
-
TP316H vs TP316 — which should I order under ASTM A312?
- Order A312 TP316 when ordinary 316 chemistry at 75/30 ksi is enough. Order TP316H when the design needs the H package: C 0.04–0.10%, grain size No. 7 or coarser and the TP304H-group anneal. A dual TP316/TP316H heat is possible only in the 0.04–0.08% carbon overlap with grain size controlled and both marks ordered.
-
Seamless vs welded TP316H pipe — which is better?
- Seamless is preferred for high-pressure, thick-wall or owner specifications that exclude welded pipe. Welded and HCW routes are fully valid under ASTM A312 when the strip or plate heat carries the full TP316H chemistry and the inspection plan matches the design class, so choose the route from the code and wall schedule rather than habit.
-
Hydrostatic test vs NDE — which do I get on TP316H pipe?
- Each length is hydrostatically tested or nondestructively electrically tested, and the manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification locks one method, state it on the PO and check that the chosen test appears on the MTC for every length, because a silent mill option is not an approved project method.
-
What heat treatment applies to TP316H pipe?
- Table 2 lists TP316H with TP304H at 1900 °F [1040 °C] minimum, followed by rapid cooling. Reheat rules and lot marking travel with the H package. Hot-finished size notes should be read from the ordered edition; we cite the 1900 °F listing and do not invent extra footnotes.
-
What Table 1 chemistry defines TP316H?
- Table 1 requires C 0.04–0.10%, Mn ≤2.00, P ≤0.045, S ≤0.030, Si ≤1.00, Cr 16.0–18.0, Ni 10.0–14.0 and Mo 2.00–3.00%. Product analysis, when ordered, applies A480 A1.1 tolerances on top of those melting limits, and every element should be reported on the MTC.
-
What are the tensile requirements for ASTM A312 TP316H?
- Table 4 sets 75 ksi [515 MPa] tensile / 30 ksi [205 MPa] yield with 35% L / 25% T elongation, plus Table 5 grain size No. 7 or coarser. These are lot minima for release, while design allowables still come from the applicable piping or pressure code rather than from a product page summary.
-
What filler metal is used to weld TP316H pipe?
- Table 6 assigns ER316H. Freeze that class on the WPS and qualify the procedure on TP316H material when creep strength matters. ER316L is a convenience swap that undercuts the reason the base metal was ordered as an H grade for hot service.
-
Does TP316H require grain-size control?
- Yes. Table 5 requires ASTM grain size No. 7 or coarser for TP316H. A heat that meets tensile and carbon but fails grain size is not TP316H under A312, so ask for the grain-size result on the same MTC as chemistry and tensile.
Conclusion
ASTM A312 TP316H / UNS S31609 is the high-temperature member of the 316 family: C 0.04–0.10%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00%, a 75/30 ksi Table 4 floor with 35% L / 25% T elongation, grain size No. 7 or coarser, a 1900 °F [1040 °C] anneal listed with TP304H and ER316H filler. It is not a drop-in for A312 TP316L. Put the manufacturing type, size and wall, finish and grade-specific chemistry evidence on the purchase order, then review the EN 10204 3.1 MTC before release. SHH STEEL can supply ASTM A312 TP316H pipe to the edition you name; browse sister grades on the A312/A312M hub, or send your size list to admin@steelspecs.com.