ASTM A312 TP316Ti Stainless Steel Pipe
What is ASTM A312 TP316Ti Stainless Steel Pipe
ASTM A312/A312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. It is an ASTM product specification in its own right; ASME SA-312 is a separate Code Book adoption of related text, and the two should not be treated as interchangeable titles on a purchase order. This page is written against A312/A312M for TP316Ti / UNS S31635, with numbers taken from the referenced A312/A312M tables.
Within that scope, TP316Ti / UNS S31635 is the titanium-stabilized 316 grade for welded service in the sensitizing range. Table 1 caps carbon at 0.08% and silicon at 0.75% (tighter than the 1.00% Si ceiling on many 316 siblings), requires Mo 2.00–3.00%, limits N to ≤0.10%, and sets titanium at 5 × (C+N) minimum up to 0.70% maximum so carbon is tied up as titanium carbide rather than chromium carbide. Table 4 releases TP316Ti at 75 ksi [515 MPa] tensile / 30 ksi [205 MPa] yield with 35% L / 25% T elongation, and there is no Table 5 grain-size requirement. UNS S31635 is not individually listed in Table 2, so the default solution anneal at 1900 °F [1040 °C] minimum with rapid cooling applies.
SHH STEEL can supply ASTM A312 TP316Ti stainless steel pipe as seamless (SML), welded (WLD), or heavily cold-worked (HCW) product in ASME B36.19 schedules and special OD/wall combinations, with EN 10204 3.1 mill test certificates as standard and third-party 3.2 inspection when the enquiry asks for it. Dual A312/SA-312 marking is available only when the purchase order names both editions and the mill heat qualifies under each—do not assume a single stamp covers Code stamping without that instruction. For the separate ASME-framed page on the same grade, see SA312 TP316Ti.
European buyers often cross-reference EN 1.4571 or the trade name 316Ti; those maps are useful but approximate. Always recheck the Ti formula against heat C+N, the Si ≤0.75% limit, and the Mo band on the A312 MTC before accepting an EN dual mark. Stabilization is not the same as the TP316L low-carbon route—Ti-stabilized heats can sit higher in carbon while still resisting sensitization, which is why the two grades are not drop-in substitutes.
Within the ASTM A312 series, buyers comparing TP316Ti usually look next at A312 TP316L, A312 TP316, A312 TP321, A312 TP316H, and A312 TP347. Browse the full grade list on the A312/A312M hub when the datasheet leaves more than one 316-family option open.
Manufacturing Types (SML / WLD / HCW)
ASTM A312 recognizes three manufacturing routes for TP316Ti pipe, and the route is a purchase-order decision driven by the design code, the size range, wall thickness, and how the owner wants the pipe inspected. The route never changes the chemistry: whichever way the pipe is made, the heat must still meet C ≤0.08%, Si ≤0.75%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00%, N ≤0.10%, and Ti 5×(C+N) min to 0.70% max, and every length must still go through the solution anneal at 1900 °F [1040 °C] minimum before it is released.
- Seamless (SML) — no welding at any stage. Preferred for high-pressure service, thick walls, and owners who exclude welded pipe from the design class. Stabilized grades are often ordered welded for process skids; make sure the coil or plate heat reports Ti against the actual C+N of that heat, not a catalogue minimum.
- Welded (WLD) — automatic welding without filler metal, with the weld finished so the pipe meets dimensional and mechanical requirements after the final heat treatment. The strip or plate heat must itself carry the full TP316Ti chemistry, so ask for the coil or plate heat number on the certificate.
- Heavily cold-worked (HCW) — welded pipe cold worked to at least 35% reduction of wall and weld before the final anneal, again without filler in the longitudinal seam, with the weld radiographed before cold work. Order HCW when the project specifically wants that marking and the process controls A312 writes around it.
Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test in place of the hydrotest, and lots for mechanical testing follow the sampling clauses in the referenced edition. State SML, WLD, or HCW on the enquiry so mill slots and test plans line up before the heat is poured.
Chemical Composition of ASTM A312 TP316Ti
Two chemistry layers matter for ASTM A312 TP316Ti. Melting analysis under Table 1 is mandatory, and product analysis under A480 A1.1 applies when S1 is ordered. The defining checks are titanium at 5 × (C+N) minimum to 0.70% maximum, silicon ≤0.75%, and Mo 2.00–3.00%. A heat that reports Ti as a single number without C and N cannot be verified against the formula.
Table 1 melting limits for TP316Ti / UNS S31635 are shown below.
| Element | TP316Ti / UNS S31635 melting analysis |
|---|---|
| Carbon (C) | ≤ 0.08 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 0.75 |
| Chromium (Cr) | 16.0 – 18.0 |
| Nickel (Ni) | 10.0 – 14.0 |
| Molybdenum (Mo) | 2.00 – 3.00 |
| Titanium (Ti) | 5 × (C+N) min, 0.70 max |
| Nitrogen (N) | ≤ 0.10 |
Product-analysis limits after A480 A1.1 tolerances follow. Titanium’s product maximum is listed with the A1.1 note on the 0.70% melting max; the minimum remains tied to the heat’s actual C+N.
| Element | Melting (Table 1) | Tolerance (A480 A1.1) | Product analysis limit |
|---|---|---|---|
| Carbon (C) | ≤ 0.08 | 0.01 over | ≤ 0.09 |
| Manganese (Mn) | ≤ 2.00 | 0.04 over | ≤ 2.04 |
| Phosphorus (P) | ≤ 0.045 | 0.010 over | ≤ 0.055 |
| Sulfur (S) | ≤ 0.030 | 0.005 over | ≤ 0.035 |
| Silicon (Si) | ≤ 0.75 | 0.05 over | ≤ 0.80 |
| Chromium (Cr) | 16.0 – 18.0 | 0.20 under / over | 15.80 – 18.20 |
| Nickel (Ni) | 10.0 – 14.0 | 0.15 under / over | 9.85 – 14.15 |
| Molybdenum (Mo) | 2.00 – 3.00 | 0.10 under / over | 1.90 – 3.10 |
| Titanium (Ti) | 5 × (C+N) min, 0.70 max | 0.05 over on max (Ti to 1.00 band) | max ≤ 0.75 product; min tied to heat C+N |
| Nitrogen (N) | ≤ 0.10 | 0.01 over | ≤ 0.11 |
Because Ti min depends on C+N, ask the mill to print the calculated 5 × (C+N) value next to the reported Ti on the MTC. That single line prevents receiving arguments when carbon sits near the 0.08% ceiling and titanium looks “low” against a fixed catalogue number.
Mechanical Properties of ASTM A312 TP316Ti
Room-temperature tensile requirements for ASTM A312 TP316Ti follow Table 4 as summarized below. The 75/30 ksi floor matches TP316 and TP316L; stabilization is a chemistry story, not a tensile upgrade. There is no Table 5 grain-size requirement on TP316Ti.
| Property | TP316Ti |
|---|---|
| Tensile, min | 75 ksi [515 MPa] |
| Yield, min | 30 ksi [205 MPa] |
| Elongation | 35% L / 25% T |
| Grain size | No Table 5 requirement |
Designers sometimes expect Ti-stabilized pipe to out-tensile low-carbon 316L at room temperature; A312 does not write that expectation into Table 4. Use the tensile row for release checks and the Ti formula for sensitization resistance, not the other way around.
Dimensions, Tolerances and Stock Sizes
Dimensional supply for ASTM A312 TP316Ti pipe follows ASME B36.19 schedules for the common NPS and schedule combinations, with special OD and wall available by agreement when a project needs a section the schedules do not cover. Outside-diameter variations follow ASTM A999/A999M, and wall-thickness variations follow A312 Table 3 as summarized below. State on the purchase order whether wall is nominal or minimum (Supplementary S8), because the two readings produce different pipe from the same size line.
| NPS designator | Wall over | Wall under |
|---|---|---|
| 1/8 to 2-1/2 incl., all t/D | 20.0% | 12.5% |
| 3 to 18 incl., t/D up to 5% | 22.5% | 12.5% |
| 3 to 18 incl., t/D over 5% | 15.0% | 12.5% |
| 20 and larger, welded, all t/D | 17.5% | 12.5% |
| 20 and larger, seamless, t/D up to 5% | 22.5% | 12.5% |
| 20 and larger, seamless, t/D over 5% | 15.0% | 12.5% |
- Lengths — single random, double random, or cut-to-length on order
- Cut lengths — typically no more than 1/4 in. [6 mm] over the ordered length unless the PO states a tighter band
- Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen
Stabilized process lines frequently mix B36.19 schedules with a few special OD×wall spools; list both clearly so the mill does not force everything onto the nearest schedule. Straightness, end finish, and length tolerance should be written into export orders so receiving inspection has an agreed acceptance basis instead of arguing after arrival. Jointers are not permitted unless the purchase order allows them, so cut-to-length programmes should include an allowance for fit-up scrap rather than expecting the mill to ship short pieces.
Stock / Available sizes. SHH STEEL quotes TP316Ti against a practical stock-and-mill enquiry range rather than a frozen warehouse SKU list. The representative sizes below are the combinations we most often discuss for ASTM A312 TP316Ti; availability by manufacturing type and exact wall still has to be confirmed on enquiry, and we do not publish fake tonnages against individual lines.
| Representative size | Typical schedules / notes |
|---|---|
| NPS 1/2 – 2 | Sch 10S / 40S / 80S; common process take-offs |
| NPS 2-1/2 – 6 | Sch 10S / 40S / 80S; frequent mill and stock enquiry sizes |
| NPS 8 – 12 | Sch 10S / 40S; confirm SML vs WLD on enquiry |
| NPS 14 – 24 | Sch 10S / 40S; often mill-order depending on wall and route |
| Special OD × wall | By agreement — state OD, wall (nominal or minimum), and length practice |
Special OD×wall, non-standard lengths, and mixed SML/WLD packages are routine on enquiry. Send NPS or OD × wall, schedule or minimum wall, manufacturing type, and quantity, and we will answer with what can ship from selected stock versus what needs a mill slot.
Equivalent Grades
Equivalent designations help sourcing, but they do not replace the ASTM A312 grade line on the purchase order. The table below lists the primary ASTM identity for TP316Ti, the separate ASME twin, and the most common commercial or EN cross-references we see on enquiries.
| Designation | Notes |
|---|---|
| ASTM A312 TP316Ti / UNS S31635 | Governing product specification on this page |
| ASME SA-312 TP316Ti / S31635 | Separate Code Book twin — dual-mark only when PO names both |
| EN 1.4571 / 316Ti trade (approx.) | Recheck Ti formula, Si ≤0.75, and Mo on the A312 MTC |
EN 1.4571 maps are widely used but still approximate. Ti min vs C+N, silicon, and molybdenum on the ASTM certificate remain the acceptance basis when the PO cites A312 TP316Ti.
Heat Treatment and Delivery Condition
TP316Ti is not individually listed in Table 2, so the default solution anneal at 1900 °F [1040 °C] minimum applies, followed by rapid cooling in water or by other rapid means. Stabilization does not replace the anneal: titanium ties up carbon, but the pipe still needs the solution treatment A312 requires for austenitic grades.
Delivery is typically annealed and pickled. When EN 1.4571 dual marking is requested, confirm that the anneal evidence and Ti formula on the A312 certificate still satisfy the ASTM order—dual marking is an extra agreement, not a substitute specification.
Corrosion Resistance
A312 does not contain a corrosion table; the comments below are engineering notes. TP316Ti has the same Cr, Ni, and Mo band as the rest of the 316 family, so pitting resistance tracks Mo and surface condition rather than titanium. Titanium’s job is to reduce the risk of chromium-carbide sensitization during welding or service in the sensitizing temperature range.
Stabilization and low-carbon strategies solve overlapping but not identical problems. When the datasheet already freezes C ≤0.030% or ≤0.035% and does not ask for Ti, A312 TP316L is usually the simpler ASTM A312 path. Choose TP316Ti when the project explicitly wants Mo plus titanium stabilization, or when an EN 1.4571 dual mark is part of the sourcing plan.
Applications of ASTM A312 TP316Ti Pipe
Applications for ASTM A312 TP316Ti combine moderate chloride resistance with stability during welding or service in the sensitizing range. The table below shows common enquiry patterns.
| Application | Why | Note |
|---|---|---|
| Welded process lines needing Mo + stabilization | Ti + Mo 2–3% | Prove Ti ≥5×(C+N) |
| Chemical plants replacing 316L where C creeps up | Stabilization | Compare 316L economics |
If the datasheet lists more than one 316-family option, walk the chemistry and tensile rows on this page against the sister ASTM A312 grades before freezing the PO. A wrong sister grade is harder to untangle after the pipe is bevelled and welded into the rack.
Weldability
Table 6 in the extracted edition does not assign an AWS filler class to TP316Ti, so the consumable is by agreement (no AWS class assigned in the extracted Table 6) and must be named on the WPS. Industry practice is either a 316-type filler or a titanium-bearing / stabilized consumable agreed with the welding engineer; do not leave the choice as “316 something” on the shop floor.
Prove that the base-metal Ti still meets 5 × (C+N) on the heat used for procedure qualification. A WPS run on an under-stabilized heat does not protect production heats that barely clear the formula.
Surface Finishes
Surface condition for ASTM A312 TP316Ti pipe should be stated on the purchase order rather than left to mill default. For stainless pipe, embedded free iron, residual scale, and chloride contamination from handling can matter as much as the nominal finish name, especially on aqueous or clean-process lines.
- Annealed and pickled — the usual delivery for process piping after solution treatment
- Blasted and pickled — when scale removal needs a mechanical assist before passivation
- Bright annealed — by agreement for selected sizes and routes
- Polished (OD/ID) — grit or Ra target by agreement; state which surface is polished
Export orders should also say how ends are protected and whether chlorine-bearing labels or cards are banned from contact with the bore. Those handling notes prevent avoidable rejection at receiving without changing the A312 metallurgical release.
Inspection and Testing
The base acceptance package for ASTM A312 TP316Ti pipe combines chemistry, tensile testing, heat-treatment evidence, and a pressure or electrical integrity test on every length. Flattening or bend tests apply per the manufacturing type and size rules in the referenced edition. Require C, N, and Ti with a printed 5 × (C+N) check on the MTC.
Supplementary requirements are optional until written on the order. The options buyers request most often for this grade are summarized below.
| Option | Purpose |
|---|---|
| S1 product analysis | Confirms chemistry on finished pipe |
| S5 radiography | Weld integrity on WLD pipe |
| S7 intergranular corrosion | A262 Practice E after sensitizing treatment |
| S8 minimum wall | Wall interpreted as minimum rather than nominal |
| S9 weld decay | Compares weld and base-metal loss rates |
EN 10204 3.1 certification is our standard document set; 3.2 third-party inspection is arranged when the enquiry names the agency and hold points. Hydrostatic versus NDE selection belongs on the PO—silent mill option is not the same as an approved project method.
Packaging and Shipping
Export and domestic shipments of ASTM A312 TP316Ti pipe are packed for handling and for ocean or land transport. Each length is marked with ASTM A312 (and SA-312 when dual-certified), TP316Ti / UNS S31635, the manufacturing type, size, heat number, and test method. Bundle or crate lists should repeat the heat numbers so receiving can match pipe to certificates without opening every wrap.
- Ends capped or bevelled and protected as ordered
- Bundles strapped with stainless or protected contact points to limit iron contamination
- Waterproof wrapping for ocean freight when specified
- Packing list with heat numbers, sizes, and certificate references
Special marking (colour codes, project tag numbers, or bilingual stencils) is available on confirmed orders. Tell us the destination and handling limits early so packing matches the lift plan without repacking at the port.
Why Choose SHH STEEL
SHH STEEL supplies specification-driven stainless plate and pipe, and for ASTM A312 TP316Ti we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 chemistry, the Table 4 tensile results, and the heat-treatment evidence the grade requires, then match manufacturing type and size to the enquiry instead of pushing a one-size stock answer.
- Ti 5 × (C+N) verification printed with C and N on the MTC
- Si ≤0.75% and Mo 2–3% checked against EN 1.4571 dual-mark requests
- Filler-by-agreement handling so the WPS does not ship with a blank consumable line
- SML, WLD, and HCW routes with EN 10204 3.1 MTCs; 3.2 inspection on request
- Dual A312/SA-312 marking only when the purchase order asks for both editions
- Project packing, cut lengths, and beveling coordinated on confirmed orders
If you are still choosing among 316-family ASTM A312 grades, send the design temperature, welded vs seamless preference, and any EN dual-mark need—we will answer with the grade that actually fits rather than the one that is merely closest in name.
Supply Capability
SHH STEEL can supply ASTM A312 TP316Ti stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade.
| Item | SHH STEEL capability for TP316Ti |
|---|---|
| Standard | ASTM A312 / A312M TP316Ti / UNS S31635 |
| Manufacturing types | SML, WLD, HCW |
| Size | NPS 1/8 and up per ASME B36.19; special OD/wall by agreement |
| Schedules | 5S, 10S, 40S, 80S and non-standard walls |
| Length | SRL, DRL, or cut-to-length |
| Finish | Annealed and pickled; blasted and pickled; bright annealed or polished by agreement |
| Filler guidance | By agreement — no AWS class in extracted Table 6 |
| Testing | Tension (75/30 ksi), flattening/bend, hydro or NDE per length; C, N, and Ti on MTC with 5 × (C+N) check; 1900 °F default anneal stated; S1/S5/S7/S8/S9 on order |
| Documents | EN 10204 3.1 with full Table 1 chemistry; third-party inspection / 3.2 on request |
| Trade terms | FOB / CFR / CIF / EXW and other agreed Incoterms |
Stock / Available sizes. Representative stockable and mill-enquiry sizes for TP316Ti are listed in the Dimensions section (NPS 1/2–24 with Sch 10S/40S/80S as typical). Selected common OD×wall combinations may be available from stock; heavy-wall seamless, unusual schedules, and special cut lengths are normally mill-order. We do not invent warehouse SKUs or tonnage claims—ask for a live check against your size list.
Enquiries should state the A312 edition, TP316Ti (UNS S31635), SML/WLD/HCW, NPS or OD × wall (and whether wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements, so mill slots line up with your need date. Dual SA-312 marking, cut lengths, beveling, and packing-list marking are available on confirmed orders.
FAQ
-
Is ASTM A312 the same as ASME SA-312 for TP316Ti?
- ASTM A312/A312M and ASME SA-312/SA-312M of a referenced edition are technically aligned on Table 1 chemistry, Table 4 tensile, manufacturing types and most testing language, but they remain two independent standards. Dual A312/SA-312 marking is available when the purchase order names both editions and the heat qualifies under each, so write both on the PO rather than treating the titles as synonyms.
-
What is the UNS number for ASTM A312 TP316Ti?
- TP316Ti is UNS S31635. Keep S31635 on the MTC with carbon, nitrogen and titanium so the 5 × (C+N) minimum can be checked. A bare “316Ti” stencil without the UNS number and formula evidence is incomplete for ASTM acceptance.
-
TP316Ti vs TP316L — which should I order?
- A312 TP316L uses a low-carbon ceiling for sensitization control, while TP316Ti uses titanium stabilization, allows C up to 0.08% and limits Si to 0.75%. They are not drop-in substitutes, so order the mechanism the datasheet actually wrote.
-
TP316Ti vs TP321 — what is the difference?
- A312 TP321 is titanium-stabilized without the 2–3% molybdenum band. TP316Ti adds Mo for chloride-bearing service. If the process needs molybdenum plus stabilization, stay on TP316Ti; if Mo is not required, TP321 may be the simpler stabilized path.
-
Seamless vs welded TP316Ti pipe — which is better?
- Seamless is preferred for high-pressure, thick-wall or owner specifications that exclude welded pipe. Welded and HCW routes are fully valid under ASTM A312 when the strip or plate heat carries the full TP316Ti chemistry and the inspection plan matches the design class, so choose the route from the code and wall schedule rather than habit.
-
Hydrostatic test vs NDE — which do I get on TP316Ti pipe?
- Each length is hydrostatically tested or nondestructively electrically tested, and the manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification locks one method, state it on the PO and check that the chosen test appears on the MTC for every length, because a silent mill option is not an approved project method.
-
Can TP316Ti be dual-certified with EN 1.4571?
- Dual marking is possible by agreement when the heat meets both the ASTM A312 TP316Ti chemistry, including Ti against C+N and Si ≤0.75%, and the EN 1.4571 requirements named on the order. Recheck the formula on the A312 MTC rather than trusting the EN stamp.
-
What heat treatment applies to TP316Ti?
- TP316Ti is not individually listed in Table 2, so the default solution anneal at 1900 °F [1040 °C] minimum with rapid cooling applies. Titanium stabilization does not replace that anneal, and there is no Table 5 grain-size requirement for this grade.
-
What Table 1 chemistry defines TP316Ti?
- Table 1 requires C ≤0.08%, Mn ≤2.00, P ≤0.045, S ≤0.030, Si ≤0.75, Cr 16.0–18.0, Ni 10.0–14.0, Mo 2.00–3.00, N ≤0.10 and Ti 5 × (C+N) minimum to 0.70% maximum, with product analysis following A480 A1.1.
-
What filler metal is used to weld TP316Ti pipe?
- The extracted Table 6 assigns no AWS class to TP316Ti, so the consumable is by agreement and must be named on the WPS. Common practice is a 316-type or stabilized filler approved by the welding engineer; never leave a blank consumable line on the traveler.
-
How much titanium does TP316Ti need?
- Titanium must be at least 5 × (C+N) and not more than 0.70% on melting analysis. Because the minimum depends on the heat’s carbon and nitrogen, ask the mill to print the calculated 5 × (C+N) value next to reported Ti so it can be verified.
Conclusion
ASTM A312 TP316Ti / UNS S31635 is titanium-stabilized 316 pipe: C ≤0.08%, Si ≤0.75%, Cr 16.0–18.0%, Ni 10.0–14.0%, Mo 2.00–3.00%, N ≤0.10% and Ti 5 × (C+N) to 0.70% max, released at 75/30 ksi after a default 1900 °F [1040 °C] anneal. It is not a drop-in for A312 TP316L. Put the manufacturing type, size and wall, finish and grade-specific chemistry evidence on the purchase order, then review the EN 10204 3.1 MTC before release. SHH STEEL can supply ASTM A312 TP316Ti pipe to the edition you name; browse sister grades on the A312/A312M hub, or send your size list to admin@steelspecs.com.