ASME SA213 TP316LNM Stainless Steel Tube | ASME SA213 Stainless Steel - SHH STEEL

ASME SA213 TP316LNM Stainless Steel Tube

ASME SA213 TP316LNM (table Grade TP316LN) / UNS S31653 low-carbon N-strengthened Mo seamless boiler, superheater and heat-exchanger tube — C ≤0.035% (Footnote D to 0.040% for small OD / thin wall), Cr 16.0–18.0%, Ni 10.0–13.0%, Mo 2.00–3.00%, N 0.10–0.16%, Table 4 75/30 ksi floor, hardness max 192 HBW / 90 HRB, 1900 °F solution anneal with Footnote F quench capability. SHH STEEL supplies cold-finished and hot-finished seamless tube with EN 10204 3.1 MTCs.
Grade
TP316LNM / UNS S31653 (SA213 table: TP316LN)
Standard
ASME SA213 / SA213M
Product form
Seamless boiler / superheater / heat-exchanger tube (cold-finished and hot-finished)
Size
Typical OD × min wall (or average wall) within ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD and ~0.015–0.500 in. [0.4–12.7 mm] wall; other diameters by agreement
Share:
Overview
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASME SA213 TP316LNM Stainless Steel Tube

ASME SA-213 / SA-213M is the ASME Boiler and Pressure Vessel Code Book adoption of the seamless ferritic and austenitic alloy-steel boiler, superheater, and heat-exchanger tube product text. When Code-stamped exchangers, boilers, or registered systems invoke that adoption by name, SA-213 is the governing product standard — an independent Code Book line, not a merged title with ASTM A213. Use SA213/SA213M as the series entry point.

This article’s commercial / queue title is TP316LNM for UNS S31653 — the same chemistry row the SA-213 / A213 stainless table prints as Grade TP316LN. The grade sits where three design needs meet on one datasheet: low carbon for as-welded intergranular resistance, nitrogen for recoverable tensile strength, and molybdenum for chloride-leaning corrosion. Melting carbon is capped at 0.035% (Footnote D raises that ceiling to 0.040% for small-diameter or thin-wall tube that needs many drawing passes), nitrogen is locked at 0.10–0.16%, chromium 16.0–18.0%, nickel 10.0–13.0%, and molybdenum 2.00–3.00%. Nitrogen brings Table 4 tensile acceptance back to 75 ksi [515 MPa] / 30 ksi [205 MPa] — the TP316 pair — instead of the lower 70/25 ksi floor that plain SA213 TP316L accepts.

SHH STEEL can supply ASME SA213 TP316LNM (TP316LN / UNS S31653) as seamless cold-finished and hot-finished tube in the usual OD × wall / BWG band, with EN 10204 3.1 certificates that report carbon, nitrogen, and molybdenum together with the 75/30 ksi tensile set. Dual SA-213/A213 marking is added only when the purchase order asks; the live twin is A213 TP316LNM. Agree the stencil string (TP316LN vs TP316LNM) on the PO before the heat ships.

Shop names include “316LN,” “316LNM,” “S31653,” and “L+N Mo tube.” Helpful for routing; the purchase order should still carry ASME SA-213 Grade TP316LN / TP316LNM / UNS S31653, wall basis, OD × wall or BWG, finish route, and any Supplementary Requirements (including S4 / A262 Practice E when Footnote F capability must be demonstrated). Sister SA213 pages include SA213 TP316L, SA213 TP316N, SA213 TP316, and SA213 TP304LN when L+N is wanted without Mo. Seamless only — no Manufacturing Types (SML / WLD / HCW) H2.

Chemical Composition of SA213 TP316LNM

Two chemistry layers matter for TP316LNM / TP316LN under ASME SA-213. Melting (heat or ladle) analysis is mandatory for every heat; product analysis on finished tube applies only when Supplementary Requirement wording or the purchase order invokes it through the general requirements (commonly ASTM A1016/A1016M). Product-analysis tolerances typically flow from ASTM A480/A480M Table A1.1. Reviewers should verify C ≤0.035% (or Footnote D 0.040% when that path applies), Mo 2.00–3.00%, N 0.10–0.16%, and Ni 10.0–13.0% together — a heat that clears TP316L without nitrogen fails this row, and a TP316N heat with C above 0.035% fails the L path.

UNCERTAIN: exact SA-213 / A213 edition year; stainless chemistry table number; A480 N product-tolerance digits (0.01 under / 0.02 over from sister practice); Footnote D exact OD/wall trigger for the 0.040% C path; full Footnote F / S4 Practice E wording; Table 4 TP316LN/S31653 row OCR gap on one public A213–13 excerpt (mech 75/30/35/192 taken from Peninsular / sister LN practice) — confirm on the ordered edition.

Melting analysis

Element TP316LNM / TP316LN (UNS S31653) melting analysis
Carbon (C) ≤ 0.035 (Footnote D: ≤ 0.040 for small OD / thin wall with many drawing passes)
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 16.0 – 18.0
Nickel (Ni) 10.0 – 13.0
Molybdenum (Mo) 2.00 – 3.00
Nitrogen (N) 0.10 – 0.16

That melt table is the acceptance chemistry for every heat of SA213 TP316LNM. Carbon must clear the L ceiling; nitrogen must sit inside 0.10–0.16%; molybdenum 2.00–3.00% remains mandatory. Footnote D’s 0.040% path is for small-OD / thin-wall tube that needs many drawing passes — it is not a free upgrade to 0.040% on every size. Exact trigger dimensions are UNCERTAIN pending the ordered edition.

Product analysis (when required)

Element Melting Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.035 0.01 over ≤ 0.045
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 16.0 – 18.0 0.20 under / over 15.80 – 18.20
Nickel (Ni) 10.0 – 13.0 0.10 under / 0.15 over 9.90 – 13.15
Molybdenum (Mo) 2.00 – 3.00 0.05 under / 0.10 over 1.95 – 3.10
Nitrogen (N) 0.10 – 0.16 0.01 under / 0.02 over 0.09 – 0.18

When product analysis is invoked, A480 tolerances apply as shown. Carbon’s product limit of ≤0.045% is the 0.01-over practice on the 0.035% melt max — Footnote D’s melt path to 0.040% does not silently rewrite product-analysis arithmetic without edition confirmation. Nitrogen’s product window uses the sister LN 0.01-under / 0.02-over practice (UNCERTAIN digit confirmation).

Snapshot vs sister grades

Element TP316L (S31603) TP316LNM (S31653) TP316N (S31651)
C ≤ 0.035 ≤ 0.035 ≤ 0.08
Ni 10.0 – 14.0 10.0 – 13.0 10.0 – 13.0
Mo 2.00 – 3.00 2.00 – 3.00 2.00 – 3.00
N … 0.10 – 0.16 0.10 – 0.16
Table 4 tensile / yield 70 / 25 ksi 75 / 30 ksi 80 / 35 ksi

Against SA213 TP316L, nitrogen restores the 75/30 ksi floor and tightens Ni to a 13% ceiling. Against SA213 TP316N, carbon drops to the L path while tensile sits one step below the N-only 80/35 pair. Against SA213 TP304LN, molybdenum is the separator for chloride-leaning duty.

Mechanical Properties of SA213 TP316LNM

ASME SA-213 sets the tensile acceptance floor for TP316LNM / TP316LN at 75 ksi [515 MPa] tensile strength and 30 ksi [205 MPa] yield strength (0.2% offset), with elongation of 35% minimum in 2 in. or 50 mm and hardness capped at 192 HBW / 200 HV or 90 HRB. That 75/30 pair matches ordinary TP316 and sits five ksi above plain TP316L’s 70/25 floor — nitrogen recovers the strength that low carbon would otherwise give away.

Property TP316LNM / TP316LN requirement (Table 4)
Tensile strength, min 75 ksi [515 MPa]
Yield strength (0.2% offset), min 30 ksi [205 MPa]
Elongation in 2 in. or 50 mm, min 35%
Hardness, max 192 HBW / 200 HV or 90 HRB
Grain size No mandatory ASTM grain-size number in the public heat-treatment table for TP316LN / TP316LNM

UNCERTAIN: one public A213–13 Table 4 PDF OCR omits the TP316LN/S31653 row between TP316N and TP317; the 75/30/35/192 set used here follows Peninsular / sister LN mechanical practice and matches the commercial expectation that nitrogen restores the TP316 floor — confirm the ordered edition’s Table 4 row before treating secondary catalogues as acceptance text.

Flattening, flaring, and reverse-bend tests follow SA-213 / general-requirements practice. Hydrostatic testing or NDE is selected per specification and PO. Dual-marked jobs still clear SA-213 mechanical text — see A213 TP316LNM.

Dimensions and Tolerances

Dimensional supply for ASME SA213 TP316LNM is tube language — outside diameter × wall thickness (minimum wall or average wall) and, commercially, BWG / gauge — not ASME B36.19 pipe schedules as the primary size story. Usual SA-213 sizes run from about 1/8 in. [3.2 mm] inside diameter to 5 in. [127 mm] outside diameter, with minimum wall from about 0.015 to 0.500 in. [0.4 to 12.7 mm]; other diameters may be furnished when all other requirements are met.

Heat-exchanger datasheets that pick L+N+Mo tube usually assume minimum wall — state wall basis on the purchase order. When Footnote D’s 0.040% carbon path is intended for small-OD / thin-wall drawing, say so explicitly rather than leaving the mill to guess. Outside-diameter and wall variations follow the general requirements invoked by SA-213 (commonly ASTM A1016/A1016M).

Item Typical SA213 TP316LNM dimensional practice
Product form Seamless only (cold-finished or hot-finished)
Usual size band ~1/8 in. [3.2 mm] ID to 5 in. [127 mm] OD; wall ~0.015–0.500 in. [0.4–12.7 mm]
Wall basis Minimum wall (common for HX datasheets) or average wall if PO says so
OD / wall tolerance Per general requirements (commonly A1016/A1016M) for the ordered finish
Length Straight random / cut-to-length; U-bend by agreement

BWG / gauge callouts are accepted on enquiry; certificates should still show OD and wall in inch or millimetre units. U-bends and polished ID finishes are commercial options — they do not replace L-carbon, N-band, or Mo chemistry.

Equivalent Grades

Naming around this UNS is the first trap: the SA-213 / A213 stainless table prints Grade TP316LN for UNS S31653; this steelspecs SA213 series titles the product page TP316LNM per QUEUE so the Mo identity stays visible in the commercial name. Neither nickname replaces the UNS on the MTC. Agree the stencil grade string before the heat ships.

Designation Notes
ASME SA-213 / SA-213M Grade TP316LN Table grade name for UNS S31653 — governing chemistry / heat-treatment row
TP316LNM (this series title) QUEUE / commercial page title for the same UNS — confirm PO stencil string
UNS S31653 Unified number that ties the names together
ASTM A213 TP316LNM / TP316LN Separate ASTM product specification — dual-mark only when the PO asks
Related L-grade SA213 TP316L — C ≤0.035, Mo, no N band; 70/25 ksi
Related N-grade SA213 TP316N — same N band, C ≤0.08; 80/35 ksi
Related 304LN SA213 TP304LN — L+N without Mo
Related plate A240 / SA240 flat product in the 316LN family — order plate and tube under their own standards

If a datasheet says “316LN / 316LNM or equivalent,” confirm C ≤0.035 (or Footnote D path), N 0.10–0.16, Mo 2–3, Ni 10.0–13.0, and the 75/30 ksi floor under SA-213 naming. Non-Code ASTM purchase: A213 TP316LNM.

Heat Treatment and Delivery Condition

TP316LN / TP316LNM under ASME SA-213 is furnished solution treated at a minimum of 1900 °F [1040 °C], then quenched in water or cooled rapidly by other means. The heat-treatment table carries Footnote F for this grade: quench at a rate sufficient to prevent re-precipitation of carbides, as demonstrable by the capability of tubes to pass ASTM A262 Practice E when that test is specified on the purchase order. The manufacturer is not required to run A262 Practice E unless Supplementary Requirement S4 / the PO calls for it. That heat-treatment row applies to both cold-finished and hot-finished seamless tube.

UNCERTAIN: full Footnote F / S4 Practice E edition wording — confirm on the ordered SA-213 / general-requirements text. Low carbon reduces sensitization risk, but it does not excuse a skipped or under-cooled solution treatment — nitrogen still needs to stay in solid solution for the austenite and tensile recovery the grade was ordered for.

Delivery condition for SHH STEEL TP316LNM is solution annealed and pickled (or bright annealed by agreement), with anneal temperature, quench method, carbon, nitrogen, and molybdenum on the EN 10204 3.1 certificate. No mandatory ASTM grain-size number appears for this grade in the public heat-treatment table. Put A262 Practice E on the purchase order when as-welded IGC demonstration is contractual.

Corrosion Resistance

TP316LNM inherits molybdenum’s contribution to pitting and crevice resistance from the 316 family while using low carbon to reduce chromium-carbide precipitation at grain boundaries during welding or slow cooling through the sensitizing range, and nitrogen to keep tensile capacity at the TP316 floor. That combination is why buyers step up from SA213 TP304LN when chloride-leaning fluids sit beside as-welded tube-to-tubesheet service, and why they step up from SA213 TP316L when the designer refuses the 70/25 ksi floor.

SA-213 itself does not publish a corrosion-rate table for TP316LNM; selection remains engineering judgment against fluid, temperature, velocity, and inspection philosophy. Footnote F’s A262 Practice E capability is a quench-quality demonstration path when ordered — write S4 / Practice E onto the purchase order so the test is contractual.

SHH STEEL will not rank TP316LNM as equal to higher-Mo L grades such as SA213 TP317L in severe chlorides — that claim is not supported by the product standard. For higher tensile without the L path, see SA213 TP316N.

Applications of SA213 TP316LNM Tube

TP316LNM is ordered for Code and near-Code heat-exchanger, condenser, and process-tube circuits that specify low-carbon nitrogen-strengthened molybdenum austenitic seamless tube — typically where tube-to-tubesheet joints remain as-welded, chloride-leaning aqueous duty needs Mo 2–3%, and the designer will not accept the 70/25 ksi floor of plain TP316L. Boiler / superheater use appears when the datasheet names the grade; H-grade creep duty points elsewhere.

Enquiry patterns ask for seamless cold-finished HX OD × minimum-wall tube, sometimes with ID polish or U-bends for bundle replacement. Hot-finished seamless remains available when size favors it. MTC review should always show C at or below the L ceiling, N inside 0.10–0.16%, and Mo inside 2.00–3.00% together with the 75/30 ksi tensile set.

Sister steering: plain L → SA213 TP316L; N without L → SA213 TP316N; L+N without Mo → SA213 TP304LN; higher Mo L → SA213 TP317L.

Weldability

TP316LNM tube welds with matching or near-matching Mo-bearing low-carbon austenitic filler selected for the project WPS (fabricators often call ER316L / ER316LSi). Low carbon in the base metal is the primary sensitization lever; nitrogen raises strength without rewriting filler selection. Clean practice, controlled heat input, and appropriate filler for chloride or process duty remain mandatory.

Tube-to-tubesheet procedures should name TP316LN / TP316LNM / S31653 — agree the stencil string so the WPS and MTC match. Do not assume a TP304LN WPS covers Mo-bearing 316LNM without review, and do not treat TP316LNM as an automatic TP316N substitute when the datasheet actually needs the 80/35 ksi floor.

Dual SA-213/A213 marking does not change filler selection. If A262 Practice E after fabrication or on mill product is required, state Supplementary Requirement S4 (or edition-equivalent) on the purchase order so Footnote F capability becomes contractual rather than assumed.

Surface Finishes

Standard mill delivery for ASME SA213 TP316LNM is solution annealed and pickled, leaving a clean matte finish suitable for heat-exchanger and process-tube duty. Bright annealing is available by agreement when OD appearance or polish steps favor it.

ID/OD polish and U-bend conditioning are commercial additions — they do not replace L-carbon, N-band, or Mo chemistry. End caps and dry export packaging matter more than paint on pickled stainless.

SHH STEEL notes the ordered surface route on the packing list and aligns it with the MTC finish description for receiving inspection.

Inspection and Testing

Base ASME SA-213 testing for TP316LNM includes heat analysis (C ≤0.035% or Footnote D path, Mo 2.00–3.00%, N 0.10–0.16%, Ni 10.0–13.0%), tension tests to the 75/30 ksi floors, hardness to 192 HBW / 90 HRB, and flattening / flaring tests for the ordered size. Hydrostatic testing or NDE follows the path selected on the purchase order.

Certificate reviewers should confirm carbon at the L ceiling, nitrogen inside the mandatory band, and molybdenum inside 2–3% rather than trusting a “316L family” PMI Mo peak alone. Product analysis, when ordered, applies A480 tolerances including the N window noted as UNCERTAIN digit confirmation above.

Supplementary Requirements (including S4 / A262 Practice E when Footnote F capability must be demonstrated), and third-party witness are available on request. EN 10204 3.1 is default; 3.2 when required. Dual SA-213/A213 names appear only when dual marking was ordered.

Packaging and Shipping

TP316LNM tube leaves SHH STEEL bundled, capped or end-protected, and tagged for export or domestic delivery according to length mix and bend form. Bundle tags repeat ASME SA-213 Grade TP316LN or TP316LNM (as agreed on the PO), UNS S31653, heat number, size, and wall basis so receivers can match the 3.1 certificate — including C, N, and Mo — without opening every bundle.

Export packing uses seaworthy bundling appropriate for pickled stainless. Marking follows SA-213 and any dual-mark text the PO adds, referencing A213 TP316LNM only when dual ASTM marking was ordered.

Why Choose SHH STEEL

SHH STEEL treats ASME SA213 TP316LNM as a Code Book L+N+Mo product with enforceable C ≤0.035% (Footnote D path when named), Mo 2–3%, N 0.10–0.16%, Ni 10.0–13.0%, 75/30 ksi tensile, hardness, Footnote F quench capability, and marking rules — not as “316L with nitrogen” checked only by PMI Mo. Enquiry review verifies C, N, and Mo together and agrees the TP316LN / TP316LNM stencil string before release.

That stops silent substitution with TP316L or TP316N heats on datasheets that actually require S31653. We keep SA-213 and A213 independent, dual-mark only on request, and put C + Mo + N on the 3.1 certificate so inspectors can verify all three levers.

Cross-links: SA213 TP316L, SA213 TP316N, SA213 TP304LN, SA213 TP317L, hub SA213/SA213M.

Supply Capability

SHH STEEL can supply ASME SA213 TP316LNM stainless steel tube against the edition and finish route named on your enquiry. The capability table below summarizes sizes, finishes, and documents we regularly quote, followed by the Stock / Available sizes map for L+N+Mo heat-exchanger and process tube.

Item SHH STEEL capability for TP316LNM
Standard ASME SA213 / SA213M (dual A213 marking on request)
Grade TP316LNM / TP316LN / UNS S31653 (stencil string agreed on PO)
Product form Seamless only — cold-finished and hot-finished
Size Typical OD × min wall (or average wall) in the SA-213 usual band; other diameters by agreement
Wall / gauge Minimum wall or average wall; BWG / gauge callouts accepted on enquiry
Length Cut-to-length for HX / process bundles; U-bend by agreement
Documentation EN 10204 3.1 MTC with C + Mo + N; S4 / A262 Practice E / witness on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Stock / Available sizes

SHH STEEL quotes TP316LNM against a stock-and-mill enquiry range rather than a frozen SKU or tonnage list. Representative OD × wall / BWG combinations below are an enquiry map for as-welded Mo heat-exchanger tube — confirm live availability and cut lengths on the RFQ.

OD (in.) Typical wall / BWG enquiry band Notes
1/2 – 1 BWG 16–12 / ~0.065–0.109 in. Small HX / instrument sizes; Footnote D path by agreement
1-1/4 – 2 BWG 14–10 / ~0.083–0.134 in. Common process exchanger band
2-1/2 – 3 0.120 – 0.250 in. min wall Heavier HX wall
3-1/2 – 5 0.180 – 0.300 in. min wall Upper usual SA-213 OD by agreement

Send OD × wall (or BWG), wall basis, quantity, finish route, preferred stencil string (TP316LN vs TP316LNM), any S4 / A262 Practice E requirement, and whether dual A213 marking is required. SHH STEEL returns capability against ASME SA213 TP316LNM / UNS S31653 — not a TP316L or TP316N substitute.

FAQ

Is ASME SA-213 the same as ASTM A213 for TP316LNM?
No. ASME SA-213 / SA-213M is the ASME Code Book adoption; ASTM A213 / A213M is the separate ASTM product specification. Chemistry — including C ≤0.035%, N 0.10–0.16%, and Mo 2–3% — tensile 75/30 ksi, and hardness floors align closely for a given referenced edition, but they remain independent standards. Dual-mark only when the purchase order asks for both names on the stencil and MTC.
Does ASME SA213 TP316LNM include welded or HCW tube?
No. This SA213 product page covers seamless boiler, superheater, and heat-exchanger tube only. SA-213 for the austenitic grades discussed here is a seamless tube product form; welded (WLD) and hot-finished continuous-welded (HCW) manufacturing-type labels from pipe standards are not used as product-form options on this pack. If your datasheet actually needs welded stainless pipe, order it under the matching pipe specification.
Why does this page say TP316LNM when the table prints TP316LN?
The SA-213 / A213 stainless chemistry table lists Grade TP316LN for UNS S31653. This steelspecs SA213 series uses the QUEUE commercial title TP316LNM so molybdenum stays visible in the page name. Both point to the same UNS. Agree the stencil string (TP316LN vs TP316LNM) on the purchase order so receiving inspection matches the MTC.
What is the UNS number and chemistry focus of ASME SA213 TP316LNM?
UNS S31653. Check C ≤0.035% (Footnote D may raise melt C to 0.040% for small OD / thin wall with many drawing passes), Cr 16.0–18.0%, Ni 10.0–13.0%, Mo 2.00–3.00%, and N 0.10–0.16% together. Product analysis, when ordered, applies A480 A1.1 tolerances.
TP316LNM vs TP316L — why add nitrogen under SA213?
Nitrogen 0.10–0.16% restores Table 4 tensile acceptance from 70/25 ksi on TP316L to 75/30 ksi on TP316LNM, and nickel tightens to 10.0–13.0%. Molybdenum and the L-carbon ceiling stay. Order TP316LNM when the designer refuses the lower L tensile floor; order TP316L when 70/25 ksi is acceptable without an N band.
TP316LNM vs TP316N — when do I need low carbon?
Order TP316LNM when as-welded intergranular resistance needs C ≤0.035% together with N and Mo (tensile 75/30 ksi). Order TP316N when the project accepts C ≤0.08% and wants the higher 80/35 ksi floor. Same Mo and N bands; different carbon paths and tensile pairs.
What does Footnote D mean for SA213 TP316LNM carbon?
Footnote D allows melting carbon up to 0.040% for small-diameter or thin-wall tube that requires many drawing passes. It is not a free upgrade to 0.040% on every size. Exact OD/wall trigger wording is UNCERTAIN pending the ordered edition — name Footnote D on the PO when that path is intended.
What does Footnote F mean for SA213 TP316LNM heat treatment?
Footnote F requires quench at a rate sufficient to prevent carbide re-precipitation, demonstrable by the capability of tubes to pass ASTM A262 Practice E when that test is specified. The mill is not required to run Practice E unless Supplementary Requirement S4 / the PO calls for it. Exact edition wording is UNCERTAIN — confirm on the ordered SA-213 text.
Does SA-213 set a hardness limit for TP316LNM?
Yes. Table 4 caps hardness at 192 HBW / 200 HV or 90 HRB, with 75 ksi tensile, 30 ksi yield, and 35% elongation — the TP316 mechanical row restored by nitrogen. Grade distinction versus TP316L is the N band and the higher tensile floor, not a harder product.
What heat treatment does ASME SA-213 require for TP316LNM?
Solution treatment at a minimum of 1900 °F [1040 °C] with water quench or other rapid cool, under Footnote F quench-capability wording. Public excerpts used here do not mandate an ASTM grain-size number. Name S4 / A262 Practice E on the PO when demonstration testing is contractual.
Minimum wall vs average wall — which should I order for SA213 TP316LNM?
Most heat-exchanger datasheets assume minimum wall; average wall only when the PO says so. Usual SA-213 sizes run about 1/8 in. ID to 5 in. OD with min wall about 0.015–0.500 in.; other diameters by agreement. Prefer OD × wall / BWG language over B36.19 pipe schedules.
Can you dual-certify ASME SA-213 and ASTM A213 TP316LNM?
Yes, when the purchase order asks for dual marking and the heat meets both named editions — including L-carbon, N 0.10–0.16%, Mo 2–3%, Ni 10.0–13.0%, and the 75/30 ksi floor. Dual marking is stencil and documentation practice, not proof the names are synonyms. Agree TP316LN vs TP316LNM on the stencil at the same time.

Conclusion

ASME SA213 TP316LNM (table Grade TP316LN) / UNS S31653 is the low-carbon nitrogen-strengthened molybdenum seamless stainless steel tube grade for Code boiler, superheater, and heat-exchanger service when C ≤0.035% (Footnote D path when named), Mo 2.00–3.00%, N 0.10–0.16%, Ni 10.0–13.0%, a 75/30 ksi tensile floor, hardness max 192 HBW / 90 HRB, and a 1900 °F solution anneal with Footnote F quench capability are required together. SHH STEEL supplies cold-finished and hot-finished seamless tube in the usual OD × wall / BWG band with EN 10204 3.1 MTCs that report C, Mo, and N. Compare sister grades on the same Code Book spine, or start from SA213/SA213M. Enquire with OD × wall, wall basis, quantity, stencil preference, and document needs at admin@steelspecs.com.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X