Two long stacks of GB/T 19879 Q390GJC building steel plate at SHH STEEL

GB/T 19879 Q390GJC Building Steel Plate Supplier

GB/T 19879 Q390GJC is high-performance building structure steel plate with 390 MPa minimum yield, a 390 – 510 MPa yield window, yield ratio ≤0.83 and 47 J Charpy impact at 0°C. SHH STEEL supplies Q390GJC mill-direct, 6 mm – 150 mm, with Z15, Z25 or Z35 options and full heat and product analysis.
Keywords
Q390GJC, Q390GJC steel plate, GB/T 19879 Q390GJC, Q390GJ-C, Q390GJCZ15, Q390GJCZ25, Q390GJCZ35, Q390GJ, building structure steel plate, Q390GJC supplier
Equivalent Grades
GB/T 19879 Q390GJC / GB/T 1591 Q390NC or Q390MC (no yield cap) / EN 10025 S420 (next step up; no S390) / ASTM A572 Gr.55 (380 MPa) / JIS G3106 SM520 — Material Specification: GB/T 19879-2023 (supersedes GB/T 19879-2015) — Delivery: CR, NR, N, NT, TMCP or TMCP+T; 0°C impact
Share:
General Description
Material Specification
Chemical Composition
Mechanical Properties
Q390GJC vs Q390C
Q390GJ vs Q355GJ
Material Comparison
Z15 / Z25 / Z35
Equivalent Material Grades
Weldability
Heat Treatment and Delivery Condition
Dimensions
Tolerances
Supplementary Requirements
Price and Ordering
Applications
Supply Capability
Why Choose SHH STEEL
FAQ
Conclusion

What is GB/T 19879 Q390GJC Building Steel Plate?

Q390GJC, also written Q390GJ-C or Q390 GJC, is hot-rolled steel plate for building structures under GB/T 19879. Q means yield, 390 is the minimum yield in MPa, GJ (gao jian) marks high-performance building steel, and C is the quality grade: Charpy V-notch at 0°C, at least 47 J.

The GJ rules are what the structural engineer is paying for. Q390GJC sets a maximum yield as well as a minimum, caps the yield ratio, limits carbon equivalent by thickness and delivery route, and keeps P and S low. The frame then yields where the designer expects.

Q390GJC is where many designers land when Q355GJ column plate passes 60–80 mm. A 390 MPa yield, held to 100 mm, lets the flange get about 9% thinner, and thinner plate is easier to preheat, weld and ultrasonic test.

GB/T 19879-2023 replaced GB/T 19879-2015 on 1 April 2024. The yield-ratio cap for Q390GJ is 0.83 in both editions. What changed is the thickness effect: the 2015 edition stepped yield down 10 MPa above 50 mm, while the 2023 edition holds 390–510 MPa (ReH) from 16 mm to 100 mm. Delivery codes now read CR/NR/N/NT and TMCP/TMCP+T. Sister grades are listed under GB/T 19879, including Q390GJB.

SHH STEEL (Shanghai Shenghonghe Import & Export Co., Ltd.) is a steel manufacturer and exporter and global steel mill sourcing partner, mill-direct, China origin. We ship Q390GJC cut to size with an EN 10204 3.1 or 3.2 certificate.

Material Specification

Specification element Requirement SHH STEEL compliance
Plate standard GB/T 19879-2023 Q390GJC (GB/T 19879-2015 when the drawing names it) Confirmed
Thickness for Q390GJ 6 mm – 150 mm Confirmed
Yield strength 390 MPa min; 390 – 510 MPa for 16–100 mm Confirmed
Tensile strength 510 – 660 MPa (to 100 mm) Confirmed
Yield ratio ≤ 0.83 Printed on MTC
Quality grade C, Charpy V at 0°C, KV2 ≥ 47 J, longitudinal Confirmed
Delivery condition CR, NR, N, NT, TMCP or TMCP+T As ordered
Through-thickness Z15, Z25 or Z35 to GB/T 5313 As ordered
Dimensions GB/T 709-2019, thickness tolerance Class B Confirmed
Chemistry report Heat analysis + CEV; product analysis on request Confirmed
Certificate EN 10204 3.1 or 3.2 As ordered

Grades often confused with it are GB/T 1591 Q390NC and ASTM A572 Gr.55. None of them carries the GJ yield cap or yield-ratio rule.

Chemical Composition: Heat Analysis and Product Analysis

Read the chemistry of Q390GJC in two layers. Layer one is the heat (ladle) analysis on the certificate, judged against Table 1. Layer two is product analysis on the finished plate, judged against Table 1 plus the GB/T 222 deviations (clause 7.1.4). Mixing the two causes most chemistry disputes we see.

Table 1 below is the heat analysis for Q390GJC. The columns on the right show the quality-grade groups at Q390GJ.

Table 1. Heat (ladle) analysis, GB/T 19879-2023 Table 1, %

Element Q390GJC heat analysis (%) Q390GJ B / C Q390GJ D / E
C, max 0.20 0.20 0.18
Si, max 0.55 0.55 0.55
Mn, max 1.70 1.70 1.70
P, max 0.025 0.025 0.020
S, max 0.015 0.015 0.010
V, max 0.200 0.200 0.200
Nb, max 0.070 0.070 0.070
Ti, max 0.030 0.030 0.030
Als, min 0.015 0.015 0.015
Cr, max 0.30 0.30 0.30
Cu, max 0.30 0.30 0.30
Ni, max 0.70 0.70 0.70
Mo, max 0.50 0.50 0.50
V + Nb + Ti, max (if combined) 0.22 0.22 0.22

Notes to Table 1. Total aluminium (Alt ≥ 0.020%) may replace acid-soluble aluminium. If Al, V, Nb or Ti is added alone or together at 0.015% or more, the minimum aluminium does not apply. V + Nb + Ti, when combined, is limited to 0.22%. These limits are the same in the 2015 and 2023 editions.

B and C grades share one chemistry column. D and E grades tighten carbon to 0.18%, phosphorus to 0.020% and sulfur to 0.010%, because they are tested at −20°C and −40°C.

Table 2. Product analysis limits for Q390GJC, GB/T 19879 clause 7.1.4 with GB/T 222-2025, %

Element Heat limit (%) Permitted deviation, GB/T 222-2025 Table 1 Q390GJC product analysis limit (%)
C ≤ 0.20 +0.02 ≤ 0.22
Si ≤ 0.55 +0.05 ≤ 0.60
Mn ≤ 1.70 +0.06 ≤ 1.76
P ≤ 0.025 +0.005 ≤ 0.030
S ≤ 0.015 +0.005 ≤ 0.020
V ≤ 0.200 +0.02 ≤ 0.220
Nb ≤ 0.070 ±0.005 ≤ 0.075 (Table 1 lists Nb to 0.060%; agree above that)
Ti ≤ 0.030 +0.02 ≤ 0.050
Als ≥ 0.015 −0.003 ≥ 0.012
Cr ≤ 0.30 +0.05 ≤ 0.35
Cu ≤ 0.30 +0.05 ≤ 0.35
Ni ≤ 0.70 +0.05 ≤ 0.75
Mo ≤ 0.50 Not listed in Table 1 Agree in contract (alloy-steel Table 2 would give ≤ 0.52)

How to read Table 2. The band is chosen by the Table 1 upper limit. Si ≤0.55% is above 0.37%, so +0.05% applies; Mn ≤1.70% falls in the 0.80–1.70% band, so +0.06%. For one heat an element may deviate in one direction only.

GB/T 222-2025 replaced GB/T 222-2006 on 1 December 2025. One more rule from it matters to buyers: if no reliable heat analysis exists, the product analysis must meet the heat limits with no deviation at all (clause 5.6).

Z-grade plate is cleaner still. GB/T 5313-2023 limits sulfur by heat analysis:

Z grade Heat sulfur, max (%) Reduction of area, avg / single (%)
Z15 0.010 15 / 10
Z25 0.007 25 / 15
Z35 0.005 35 / 25

CEV and Pcm are always worked out from the heat analysis, not the product analysis. SHH STEEL prints the heat values used and adds a product-analysis column on request. This is building steel, not boiler chemistry such as GB/T 713 Q345R in GB/T 713.

Mechanical Properties

Values below follow Table 3 and Table 5 of GB/T 19879-2023 for Q390GJ. Tensile specimens are transverse; Charpy specimens are longitudinal.

Thickness Upper yield ReH (MPa) Tensile Rm (MPa) Yield ratio, max Elongation A, min
6 – 16 mm ≥ 390 510 – 660 0.83 20%
> 16 – 100 mm 390 – 510 510 – 660 0.83 20%
> 100 – 150 mm 370 – 490 490 – 640 0.83 20%

The 2015 edition used lower yield ReL and stepped yield down 10 MPa above 50 mm. Write the edition on the order so the mill tests to the right table.

Test Q390GJC requirement
Charpy V-notch, longitudinal 0°C, KV2 ≥ 47 J, average of 3
Single value One value may fall below the average requirement, not below 70% of it (GB/T 17505)
Sub-size specimens 7.5 mm or 5 mm wide when plate is too thin: 75% or 50% of the required energy
180° bend Per Table 6 to GB/T 232; may be omitted when the mill guarantees it (7.4.3.2)
Through-thickness (≥ 15 mm) Z15, Z25 or Z35 to GB/T 5313, when ordered

Density for theoretical weight is 7.85 g/cm³.

Q390GJC vs Q390C (GB/T 1591): Same 390 MPa, Different Job

Q390 under GB/T 1591 and Q390GJC share a number and little else. Q390 steps yield down as plate gets thicker: by 40–63 mm the minimum is 360 MPa. Q390GJC holds 390 MPa to 100 mm, then caps it at 510 MPa.

That matters most in thick column plate, which is exactly where 390 MPa gets specified. A 60 mm flange in GB/T 1591 Q390 is really a 360 MPa flange.

Property Q390C (GB/T 1591-2018) Q390GJC (GB/T 19879-2023)
Yield at 16 mm 390 MPa 390 MPa
Yield at 16–40 mm 380 MPa min 390 – 510 MPa
Yield at 40–63 mm 360 MPa min 390 – 510 MPa
Yield upper limit None 510 MPa to 100 mm
Yield ratio No limit ≤ 0.83
Tensile to 100 mm 490 – 650 MPa 510 – 660 MPa
Impact 0°C, 34 J 0°C, 47 J
C / P / S, max Per GB/T 1591 grade 0.20 / 0.025 / 0.015%
Ni, max Per GB/T 1591 grade 0.70%
CEV ≤ 50 mm Per GB/T 1591 route 0.45% (CR/N), 0.40% (TMCP)

If the drawing says Q390C and the plate is over 40 mm, ask the designer which yield they assumed. If it was 390 MPa, Q390GJC is the safer order. The normalized comparison is GB/T 1591 Q390NC.

Q390GJC vs Q355GJC: When to Step Up a Strength Level

Check Q355GJC Q390GJC
Yield, 16–100 mm 355 – 475 MPa 390 – 510 MPa
Tensile, to 100 mm 490 – 610 MPa 510 – 660 MPa
Yield ratio ≤ 0.83 ≤ 0.83
CEV ≤ 50 mm 0.43% (AR/N) 0.45% (CR/N)
CEV TMCP ≤ 50 mm 0.38% 0.40%
Max thickness 200 mm 150 mm
Ni / Mo, max 0.30 / 0.20% 0.70 / 0.50%

The yield gain is 35 MPa, about 10%. In a strength-governed column that is roughly a 9% cut in plate thickness and weld volume. CEV rises only 0.02 points on CR/N plate.

Above 150 mm Q390GJ is not available, so very heavy sections stay at Q355GJ. Below that, compare tonnage, weld time and plate price, not plate price alone. See Q345GJC for the 355 MPa plate.

Q390GJB, Q390GJC, Q390GJD or Q390GJE: Which Quality Grade?

Grade Impact temperature Energy, min C / P / S max (%) Typical use
Q390GJB +20°C 47 J 0.20 / 0.025 / 0.015 Heated interiors, mild climates
Q390GJC 0°C 47 J 0.20 / 0.025 / 0.015 Cold regions, exposed frames
Q390GJD −20°C 47 J 0.18 / 0.020 / 0.010 Severe winters, thick welded nodes
Q390GJE −40°C 47 J 0.18 / 0.020 / 0.010 Arctic and low-temperature sites

Strength, yield ratio and CEV do not change from B to E. Only the impact temperature and the D/E chemistry move. Over-specifying the letter costs money; under-specifying it costs safety. Use the design temperature.

Q390GJC is the usual letter for temperate sites and for frames that see some frost during erection. For the same letter at another strength level: one level up, Q420GJC; one level down, Q345GJC.

Q390GJCZ15, Q390GJCZ25 and Q390GJCZ35: Through-Thickness Plate

Through-thickness ductility matters wherever the load path runs across the plate: column flanges at moment connections, cruciform nodes, anchor base plates. GB/T 5313 measures it as reduction of area on short-transverse specimens.

The designation adds the Z level to the grade, for example Q390GJCZ25. Z tests apply to plate 15 mm and thicker and follow GB/T 5313-2023.

Z grade Heat sulfur, max (%) Reduction of area, avg / single (%)
Z15 0.010 15 / 10
Z25 0.007 25 / 15
Z35 0.005 35 / 25

B and C chemistry allows S up to 0.015%, so even Z15 needs extra desulfurization.

GB/T 19879-2023 clause 7.6 requires every Z plate to be ultrasonic tested one by one to GB/T 2970, acceptance level III. Z35 costs most: lowest sulfur, more rejects, and a Z test on each plate.

Z35 on every plate is an easy line to write and an expensive one to buy. Let the joint detail decide where it goes.

Equivalent Material Grades

EN 10025 has no 390 MPa grade, so European reviewers usually check Q390GJ against S420 and accept it on the yield floor, or against S355 with a strength upgrade. Neither has the GJ ratio cap.

Designation Region Standard Notes
Q390GJC China GB/T 19879-2023 Grade on this page
GB/T 1591 Q390NC China GB/T 1591-2018 Normalized; no yield cap
GB/T 1591 Q390MC China GB/T 1591-2018 TMCP; no yield cap
EN 10025-3 S420N Europe EN 10025-3/-4 Next step up (no S390 in EN); strength only
EN 10025-2 S355K2 Europe EN 10025-2 Next step down
ASTM A572 Gr.55 USA ASTM A572 380 MPa; one step lower
JIS G3106 SM520C Japan JIS G3106 355 MPa class; no ratio rule

For mill-direct supply under the GB family, the normalized and TMCP Q390 grades in GB/T 1591 are the nearest relatives.

Weldability

GB/T 19879 makes the mill calculate CEV from the heat analysis and print it, together with the elements used, on every Q390GJC certificate:

CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15

Pcm = C + Si/30 + Mn/20 + Cu/20 + Ni/60 + Cr/20 + Mo/15 + V/10 + 5B

Delivery condition CEV ≤ 50 mm CEV > 50 – 100 mm CEV > 100 – 150 mm Pcm ≤ 50 mm Pcm > 50 – 100 mm Pcm > 100 – 150 mm
CR, NR, N, NT 0.45 0.47 0.49 0.28 0.30 0.31
TMCP, TMCP+T 0.40 0.43 By agreement 0.26 0.27 —

CR/N Q390GJ sits at 0.45% CEV to 50 mm, TMCP plate at 0.40%. The TMCP route is the easier one to weld thick, and we suggest it for column plate above 60 mm.

B/C chemistry allows C up to 0.20%. Check actual CEV on the MTC, not the table limit, when setting preheat.

Typical consumables: E50- or E55-class low-hydrogen electrodes (E5515 types) or matching ER55 wire. Shops work to GB 50661 or AWS D1.1. Write the CEV basis (actual heat, not table maximum) into the WPS.

Heat Treatment and Delivery Condition

Q390GJC may be delivered CR, NR, N or NT, or TMCP / TMCP+T. QT is not listed for Q390GJ in Table 2. Each route has its own CEV and Pcm limits, so the route is part of the specification, not a mill detail.

TMCP gives the lowest CEV and the best weldability. N or NT gives the most uniform through-thickness properties on heavy plate. QT holds strength in the thickest sizes.

Agree the route before price. A mill quoting N where the drawing assumed TMCP CEV is not quoting the same plate. TMCP references: GB/T 1591 Q390MC; normalized: GB/T 1591 Q390NC.

Test lots follow clause 9.2 of GB/T 19879-2023; retests and judgement follow GB/T 17505.

Dimensions

What we roll and cut in Q390GJC:

  • Thickness: 6 mm – 150 mm; most orders 8 mm – 100 mm
  • Width: 1500 mm – 3000 mm standard; wider by mill confirmation
  • Length: 3000 mm – 12000 mm; longer by enquiry
  • Edge: mill edge or cut edge
  • Weight: theoretical, on the mean of maximum and minimum thickness, 7.85 g/cm³

Column flanges, diaphragms, stiffeners and gussets are cut to drawing. Rolled sections for the same frame are under steel beam profiles and steel structural profiles.

Tolerances

For Q390GJC, thickness tolerance follows GB/T 709-2019 Class B unless the order says otherwise: −0.30 mm on the minus side at every thickness, with the plus side shown below. Zero-minus Class C can be agreed.

Nominal thickness (mm) Width ≤ 1500 mm Width > 1500 – 2500 mm
> 8 – 15 −0.30 / +0.80 −0.30 / +1.00
> 15 – 25 −0.30 / +1.00 −0.30 / +1.20
> 25 – 40 −0.30 / +1.10 −0.30 / +1.30
> 40 – 60 −0.30 / +1.30 −0.30 / +1.50
> 60 – 100 −0.30 / +1.50 −0.30 / +1.80
> 100 – 150 −0.30 / +2.10 −0.30 / +2.50

Flatness and width follow GB/T 709. EN 10029 or ASTM A6 tolerances are possible if written on the order.

Supplementary Requirements

Q390GJC already fixes strength, yield ratio, CEV and 0°C impact. Anything more goes on the purchase order.

  • Edition: GB/T 19879-2023 or -2015. Never write only Q390.
  • Product analysis: ask for a second chemistry column checked to GB/T 222.
  • Through-thickness: add Z15, Z25 or Z35, e.g. Q390GJCZ25.
  • Delivery condition: name it (CR, NR, N, NT, TMCP or TMCP+T) if the welding procedure depends on it.
  • Ultrasonic testing beyond Z plates: GB/T 2970 class, or EN 10160 / ASTM A578.
  • Impact: extra test positions (e.g. quarter thickness) or transverse tests, if the owner wants them beyond the C letter.
  • Tolerance: Class C for zero minus.
  • Inspection: EN 10204 3.2 with SGS, BV, TÜV or a named inspector.

Q390GJC Price Factors and How to Order

When you compare Q390GJC offers, compare extras line by line. These are the items that move the price.

Cost driver Effect on price
GJ grade over general Q390 plate Grade extra for cleaner steel, yield control and CEV
Quality letter C Small extra for 0°C testing
Delivery route TMCP or N; NT adds furnace time
Thickness Thin and very thick plate carry size extras; 10–60 mm is usually cheapest
Z15 / Z25 / Z35 Desulfurization, plate-by-plate Z test and UT; Z35 costs most
Width and length Over 3000 mm wide or 12 m long needs mill confirmation
Quantity per size Mill rolling minimums per size; small lots come from stock or combined rolling
Inspection and cutting 3.2 witness, profile cutting, blasting and priming are quoted per item

To get a firm quote in one round, send:

  • Grade and edition, e.g. Q390GJCZ25 to GB/T 19879-2023
  • Thickness × width × length and pieces or tonnes
  • Delivery route, UT standard and class
  • Certificate type and inspector
  • Destination port and Incoterm

We quote plate price, extras and freight line by line, so you can compare like with like. Need a different letter? See Q390GJE.

Applications

Sector Typical Q390GJC components
Super-tall towers Column flanges and webs above 60 mm, belt trusses
Long-span roofs Heavy truss chords and supports
Industrial buildings Heavy crane runway girders
Transfer structures Podium transfer girders where plate thickness must drop

C grade suits frames that see winter during erection or in service, and exposed members in temperate climates.

It is the wrong plate for pressure equipment (pressure vessel steel plates), for bare exposed steel (weathering steel plates) or for ship hulls (shipbuilding steel plates).

Supply Capability and Global Delivery

SHH STEEL sources Q390GJC from first-line building-steel mills: Wuyang (Wugang), a drafting mill of GB/T 19879, plus Xinyu, Valin Xiangtan, Shougang, Puyang and Hongchang when size requires.

  • Certificates: EN 10204 3.1 standard; 3.2 with third-party witness
  • Tests: tensile, 0°C Charpy, bend, Z test to GB/T 5313, UT to GB/T 2970, product analysis
  • Processing: CNC plasma and flame cutting, bevelling, drilling, shot blast and primer
  • Terms: FOB Shanghai, CFR, CIF; TT, LC or TT + LC
  • Marking: steel-stamped and paint-marked with grade, heat, size and mill

Our Q390GJC exports go where Chinese design codes go: high-rise, airport and industrial projects run by EPC contractors abroad. The same team ships GB, ASTM, ASME, EN, DIN and JIS plate worldwide.

Lead time: stock sizes about 5–7 days (B/C letters); mill rolling about 30–45 days; Z35 or 3.2 inspection adds about 1–2 weeks. Sea time from Shanghai is about 7–12 days to Singapore and 28–35 days to Rotterdam.

Why Choose SHH STEEL

SHH STEEL is mill-direct: steel manufacturer and exporter and global steel mill sourcing partner, China origin. Every Q390GJC plate we ship carries the original mill heat number.

Before shipment we check four lines on every certificate: yield inside the GJ window, yield ratio within the cap, CEV inside the thickness band for the delivery route, and 0°C impact at 47 J or more. If one fails, the plate does not ship as GJ.

We also tell buyers when they are over-specifying. If the plate is under 40 mm and strength is not critical, Q345GJC may be the cheaper answer. Browse more structural steel plates and high strength low alloy plates.

FAQ

What is Q390GJC steel?
Q390GJC is high-performance building structure steel plate to GB/T 19879. It has 390 MPa minimum yield, a 390–510 MPa yield window from 16 to 100 mm, yield ratio ≤0.83, CEV limits by delivery route and Charpy impact of at least 47 J at 0°C. GJ stands for gao jian, high-performance building steel.
What is the difference between Q390GJC and Q390C?
Q390C (GB/T 1591) guarantees 390 MPa only to 16 mm; minimum yield falls to 380 MPa above 16 mm and 360 MPa above 40 mm, with no yield cap or ratio limit. Q390GJC (GB/T 19879) holds 390–510 MPa from 16 to 100 mm, caps the yield ratio at 0.83 and needs 47 J at 0°C.
What impact test does Q390GJC require?
Q390GJC needs Charpy V-notch tests at 0°C on longitudinal specimens, with an average of at least 47 J from three tests. Plate too thin for a full 10 mm specimen is tested at 7.5 mm or 5 mm width, needing 75% or 50% of 47 J. The test applies to plate 6 mm and thicker.
Why use Q390GJ instead of Q355GJ?
Q390GJ gives 390–510 MPa yield to 100 mm versus 355–475 MPa for Q355GJ, about 10% more. In strength-governed column plate that cuts thickness and weld volume by roughly 9%, while CEV on CR/N plate rises only from 0.43% to 0.45%.
How is Q390GJC priced?
Q390GJC is priced as a base plate price plus extras: GJ grade extra, C-letter impact extra, thickness and width extras, delivery route (CR, NR, N, NT, TMCP or TMCP+T), Z15/Z25/Z35, UT class, inspection and cutting. Quantity per size matters because mills set rolling minimums.
What is the ASTM or EN equivalent of Q390GJC?
There is no exact equivalent. EN 10025 has no 390 MPa grade, so Q390GJC is compared with S420N/S420M (one step higher) or S355 (one step lower). ASTM A572 Gr.55 is 380 MPa. None of these caps yield or limits the yield ratio, which GB/T 19879 does at 0.83.

Conclusion

Q390GJC steel plate to GB/T 19879 is building structure plate with 390 MPa minimum yield, a capped yield window, a yield-ratio limit and 47 J impact at 0°C. It shares its chemistry with Q390GJB but proves toughness at its own letter. It is not general structural plate under GB/T 1591.

SHH STEEL delivers Q390GJC with the full GJ data set on an EN 10204 3.1 or 3.2 certificate: heat analysis, CEV, yield, yield ratio and impact. On request we add product analysis to GB/T 222, Z15, Z25 or Z35, GB/T 2970 UT, Class C tolerance, cutting and blasting.

We ship from Shanghai to buyers worldwide. Browse the full GB/T 19879 range or other carbon steel plates.

Ready to order? Send the drawing or cutting list, the certificate type and the destination port. Our engineers check the edition, letter and Z level before we quote, so the offer matches the drawing. Contact SHH STEEL for a mill-direct quotation on Q390GJC building steel plate.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X