ASTM A312 TP309S Stainless Steel Pipe | ASTM A312 Stainless Steel - SHH STEEL

ASTM A312 TP309S Stainless Steel Pipe

ASTM A312 TP309S / UNS S30908 heat-resisting stainless steel pipe in SML, WLD and HCW, with C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, Mo ≤0.75%, a 75/30 ksi Table 4 floor and a 1900 °F anneal, supplied by SHH STEEL with EN 10204 3.1 MTCs.
Grade
TP309S / UNS S30908
Standard
ASTM A312 / A312M
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASTM A312 TP309S Stainless Steel Pipe

ASTM A312/A312M is the ASTM product specification for seamless, straight-seam welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. It stands on its own as an ASTM document, with its own chemistry table, tensile table, heat-treatment table, and testing clauses, and a purchase order written to it should name the ASTM edition directly. This page covers Grade TP309S / UNS S30908 under that specification and draws every number from the referenced A312/A312M tables rather than from catalogue habit.

TP309S is the general-purpose, low-carbon-capped heat-resisting member of the 23Cr–13Ni ASTM A312 family. Table 1 sets C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, Mo ≤0.75%, with manganese capped at 2.00%, silicon at 1.00%, phosphorus at 0.045% and sulfur at 0.030%. The 309 family sits one step above the 304 family in chromium and nickel, and buyers usually reach for it when a line runs hot enough in air or combustion gas that 18-8 grades start to scale. Table 4 releases the grade at 75 ksi [515 MPa] tensile and 30 ksi [205 MPa] yield with 35% longitudinal / 25% transverse elongation, and the pipe is delivered solution annealed at 1900 °F [1040 °C] minimum with rapid cooling.

The “S” suffix tells you the carbon is capped at 0.08% with no lower limit, which keeps the grade easy to weld and fabricate while still giving the full 309 oxidation benefit. Read the suffix as part of the grade identity, because a length stenciled only “309” does not tell receiving inspection which Table 1 row the heat was melted to.

SHH STEEL can supply ASTM A312 TP309S stainless steel pipe as seamless (SML), welded (WLD), or heavily cold-worked (HCW) product in ASME B36.19 schedules and in special OD and wall combinations, with EN 10204 3.1 mill test certificates as the standard document package and EN 10204 3.2 or third-party witness when the enquiry asks for it. Where a project also runs under the ASME Boiler and Pressure Vessel Code, dual A312/SA-312 marking can be arranged, but only when the purchase order names both standards and the heat qualifies under each. ASME SA-312 is a separate standard with its own adoption history, and the same grade is described on its own page at SA312 TP309S.

Buyers comparing TP309S within the ASTM A312 series usually look next at A312 TP309H, A312 TP309Cb, A312 TP309HCb, and at the matching 310-family grade A312 TP310S. The full grade list is on the A312/A312M hub, which is the quickest way to check a neighbouring grade when the datasheet leaves more than one heat-resisting option open.

Manufacturing Types (SML / WLD / HCW)

ASTM A312 allows three manufacturing routes for TP309S pipe, and the choice belongs on the purchase order because it changes inspection, marking, and sometimes the design allowance, while it never changes the chemistry. Whichever route is chosen, the heat must still meet C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, Mo ≤0.75%, and every length still has to pass through the solution anneal before release.

  • Seamless (SML) — produced without welding at any stage, and preferred for high-pressure service, heavy wall, and owners who exclude welded pipe from the line class. Seamless supply in this grade is typically mill-order rather than stock.
  • Welded (WLD) — made by an automatic welding process with no filler metal in the longitudinal seam, then solution annealed. For general furnace and hot-air ducting, welded pipe is the economical choice on larger diameters and thinner walls.
  • Heavily cold-worked (HCW) — welded pipe cold worked by at least 35% reduction in both wall and weld before the final anneal, with the weld radiographed before cold work. Order HCW only when the project specifically calls for that marking and its process controls.

Chemical Composition of ASTM A312 TP309S

Two layers of chemistry matter on an ASTM A312 TP309S order. The heat (ladle) analysis is mandatory for every heat and must meet Table 1, while product analysis on the finished pipe is made only when the purchase order calls for it, using the tolerances that A312 brings in through ASTM A999/A999M and ASTM A480/A480M Table A1.1. SHH STEEL reports actual heat values on the certificate and, when ordered, product values as well; we do not quote tighter in-house windows as if they were part of the standard.

Heat analysis — ASTM A312 Table 1

The table below sets out the Table 1 heat-analysis limits for TP309S / UNS S30908. Values are maxima unless a range is shown, and an ellipsis means the edition places no requirement on that element.

Element TP309S / UNS S30908 heat analysis, %
Carbon (C) ≤ 0.08
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 22.0 – 24.0
Nickel (Ni) 12.0 – 15.0
Molybdenum (Mo) ≤ 0.75
Nitrogen (N) … (no requirement)

Reading the table, the defining lines are chromium at 22.0–24.0% and nickel at 12.0–15.0%, with carbon capped at 0.08% and no lower limit. Molybdenum is limited to 0.75%, which is a residual cap rather than an alloying addition, and no nitrogen requirement is listed. Because there is no carbon floor, TP309S is not the grade to order for creep-range design that relies on H-grade allowables; that job belongs to A312 TP309H.

Product analysis — A480/A480M Table A1.1 tolerances

When product analysis is ordered, the Table A1.1 tolerances are applied to the Table 1 limits as shown below. The tolerance applies to an individual product determination; it does not widen the heat-analysis range that the mill must meet in the first place.

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.08 0.01 over ≤ 0.09
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 22.0 – 24.0 0.25 under / over 21.75 – 24.25
Nickel (Ni) 12.0 – 15.0 0.15 under / over 11.85 – 15.15
Molybdenum (Mo) ≤ 0.75 0.05 over ≤ 0.80

309 family side by side

Because four 309-family rows sit next to each other in Table 1, it helps to see them together. The comparison below uses the same Table 1 values and shows where TP309S differs from its sisters; chromium is 22.0–24.0% for all four.

Element TP309S TP309H TP309Cb TP309HCb
C ≤ 0.08 0.04 – 0.10 ≤ 0.08 0.04 – 0.10
Ni 12.0 – 15.0 12.0 – 15.0 12.0 – 16.0 12.0 – 16.0
Mo ≤ 0.75 … ≤ 0.75 ≤ 0.75
Nb … … 10×C – 1.10 10×C – 1.10
Table 5 grain size — No. 6 or coarser — No. 6 or coarser

Reading across, the S and Cb grades share the 0.08% carbon cap, the H and HCb grades share the 0.04–0.10% band and the Table 5 grain-size rule, and the niobium line appears only on the two stabilized rows. In the 309 family the stabilized grades also allow nickel up to 16.0%, against 15.0% for TP309S and TP309H. The differences look small on paper but they decide which heats a mill can allocate, so name the exact TP designation and UNS number on the order instead of a family name.

Mechanical Properties of ASTM A312 TP309S

Room-temperature tensile requirements for TP309S come from ASTM A312 Table 4. They are minima for release testing, not typical values, and they are the same 75/30 ksi floor shared by the other 309-family grades. Mill results usually sit above these figures, but design should still use the table unless the purchase order states higher guaranteed values.

Property ASTM A312 TP309S / UNS S30908
Tensile strength, min 75 ksi [515 MPa]
Yield strength (0.2% offset), min 30 ksi [205 MPa]
Elongation in 2 in. or 50 mm (or 4D) 35% longitudinal / 25% transverse, min

TP309S has no hardness maximum in Table 4 and no Table 5 grain-size requirement, because it is not an H grade. The values above are the whole room-temperature acceptance basis, and anything stricter, such as a Rockwell limit for expanding or tight bending, has to be stated on the purchase order and reported on the certificate.

Dimensions, Tolerances and Stock Sizes

Dimensional supply for ASTM A312 TP309S follows ASME B36.19 for the standard NPS and schedule combinations, with special outside diameters and walls available by agreement when a furnace, heater, or duct needs a section the schedules do not cover. Outside-diameter variations follow ASTM A999/A999M, and wall-thickness variations follow A312 Table 3, summarized below.

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%

In short, the under-tolerance on wall is 12.5% across the whole range, while the permitted over-tolerance depends on the NPS, the wall-to-diameter ratio, and for NPS 20 and larger on whether the pipe is welded or seamless. State on the order whether the wall is nominal or minimum (Supplementary S8), because the two readings produce different pipe from the same line item, and the difference matters most on thin-wall heat-resisting ducts.

  • Lengths — single random, double random, or cut-to-length as ordered
  • Cut lengths — normally no more than 1/4 in. [6 mm] over the ordered length unless the PO sets a tighter band
  • Ends — plain or beveled; confirm bevel angle and root face if the WPS is already fixed
  • Jointers — not permitted unless the purchase order expressly allows them

Stock / Available sizes

SHH STEEL quotes ASTM A312 TP309S against a practical stock-and-mill enquiry range rather than a fixed list of stock-keeping units. The representative sizes below are the combinations most often discussed for this grade; availability for a given manufacturing route and exact wall still has to be confirmed at enquiry, and we do not publish tonnages against individual lines.

Representative size (ASME B36.19) Typical schedules / notes for TP309S
NPS 1/2 – 2 Sch 10S / 40S / 80S; instrument and small process connections
NPS 2-1/2 – 6 Sch 10S / 40S / 80S; common furnace and process line sizes
NPS 8 – 12 Sch 10S / 40S; confirm SML or WLD at enquiry
NPS 14 – 24 Sch 10S / 40S; usually welded and often mill-order depending on wall
Special OD × wall By agreement — state OD, wall (nominal or minimum), and length practice

Example enquiries we handle are framed as OD × wall, for instance NPS 4 Sch 40S or a special OD with a minimum wall for a heater coil, and we answer with what can ship from selected stock and what needs a mill slot. TP309S is the most commonly held member of the 309 family, so standard schedules are more likely to be available quickly than for the H or Cb sisters. Special sizes, cut lengths, and mixed seamless and welded packages are on enquiry.

Equivalent Grades

Equivalence for TP309S is first an identity question within ASTM A312 and only second a cross-reference to other systems. The governing designation on this page is ASTM A312 Grade TP309S / UNS S30908; trade names, plate counterparts, and foreign designations all need to be mapped back to that row before a mill is asked to substitute or dual-mark.

Designation Notes
ASTM A312 / A312M TP309S / UNS S30908 Governing pipe grade for this page
ASME SA-312 TP309S Separate ASME standard; dual marking only when the PO names both and the heat qualifies
309S (trade names) Confirm UNS S30908 chemistry on the MTC; not a grade name by itself
ASTM A240 UNS S30908 Plate and sheet counterpart — not a pipe specification
EN 1.4833 (X12CrNi23-13) Commonly cited European counterpart; verify against the EN product standard
JIS SUS309STP Commonly cited Japanese pipe counterpart; verify against JIS

Read the notes column literally: an EN or JIS designation is a starting point for engineering comparison, not a substitute grade, and the carbon and silicon limits should be checked before any dual certification is promised. Within ASTM A312 the closest relatives are A312 TP309H, A312 TP309Cb, A312 TP309HCb, but each one is a separate row with its own limits, so an order for one is not satisfied by a certificate for another.

Compared with A312 TP304, the 309 family carries more chromium and nickel and gains roughly one step of oxidation resistance, but it is not a substitute for A312 TP310S where the line really needs 25Cr–20Ni. Where a project spans pipe and plate, carry the same UNS number through both forms but still order the pipe to A312.

Heat Treatment and Delivery Condition

All pipe furnished to ASTM A312 is heat treated. TP309S does not carry its own row in Table 2, so the default practice applies: solution anneal at 1900 °F [1040 °C] minimum, followed by water quenching or another rapid cool sufficient to prevent harmful carbide precipitation. Because TP309S is not an H grade, clause 6.2 allows seamless pipe to be quenched directly after hot forming when the temperature is at or above the solution minimum, and there is no Table 5 grain-size requirement.

  • Solution annealed and rapidly cooled — 1900 °F [1040 °C] minimum (Table 2 default)
  • No Table 5 grain-size rule — unlike TP309H and TP309HCb
  • Surface — free of scale and contaminating iron; pickled or equivalent as ordered
  • Lot marking — heat-treatment lot traceability on request

Where the design worries about sensitization, Supplementary S7 demonstrates freedom from harmful carbide precipitation by ASTM A262 Practice E, and it has to be ordered; it is not part of the base test package. Bright-annealed small sizes must still reach the Table 2 minimum, so ask for the actual anneal temperature on the certificate when that finish is ordered, and make sure the mill is not applying an H-grade reheat habit, or skipping one, by mistake on a mixed campaign.

Corrosion Resistance

The case for TP309S is primarily oxidation and scaling resistance at high temperature. The 22.0–24.0% chromium forms a protective oxide that holds up in hot air and many combustion atmospheres where 18-8 grades scale away, and the 12.0–15.0% nickel keeps the matrix fully austenitic and tough through thermal cycling. The 309 family sits between the 304 family and the 310 family, which makes it a cost-effective step up when 304 is visibly scaling but 310 is more alloy than the line needs.

Because carbon is capped at 0.08% and the grade is unstabilized, TP309S can sensitize in weld heat-affected zones held in the carbide-precipitation range. That matters less in dry hot-gas service than in lines that see aqueous condensate during shutdown, where intergranular attack or polythionic-acid cracking become possible. If that risk is real, look at A312 TP309Cb, or order Supplementary S7 to verify the as-supplied condition.

Applications of ASTM A312 TP309S Pipe

Buyers typically select TP309S when the line needs 309-level oxidation resistance with straightforward fabrication and no creep-range design requirement. The table below lists the services where we most often see the grade on an enquiry, together with the reason it is chosen and the point worth checking before ordering.

Application Why TP309S Check before ordering
Furnace and kiln components 309 oxidation resistance in hot air Check thermal cycling and support spacing
Hot air and flue-gas ducting Economical welded large diameters Confirm condensate behaviour
Heat-treatment equipment Scaling resistance Carburizing service may need other alloys
Dissimilar-metal transitions Rich Cr–Ni base tolerates dilution Document filler choice on the WPS
Process heater convection sections Oxidation margin over 304 Compare the H grade if creep governs

Reading the table, the common thread is heat: TP309S is rarely bought for room-temperature corrosion alone, where cheaper grades do the job. Typical size mixes run from instrument connections at NPS 1/2–2, through process lines at NPS 3–8, up to welded ducts at NPS 12–24, and the availability of fittings and flanges in matching chemistry can limit the line list, so check companion components before the isometrics are frozen. When TP309S replaces another grade in an existing unit, review the weld procedures as well, because a base-metal change alone does not update a WPS.

Weldability

TP309S welds readily by GTAW, GMAW, SMAW, and SAW, and its fully austenitic structure means no preheat is normally required. The mill longitudinal seam on WLD and HCW pipe is made without filler metal, so the filler question only arises for field and shop joints. Table 6 of A312 shows no AWS filler classification for TP309S, which means the filler is selected by agreement on the welding procedure specification rather than dictated by the pipe standard.

In practice the WPS will usually choose a matching 309-type filler, or a richer one where dilution or dissimilar joints are involved, and that choice should be documented and qualified for the service temperature. If the welded joints will see shutdown condensate, consider whether the unstabilized grade is the right choice before blaming the filler. Keep interpass temperatures controlled, as for other high-alloy austenitics, to limit hot-cracking risk in a fully austenitic weld, and avoid long holds in the carbide-precipitation range during repair welding.

Surface Finishes

A312 requires pipe to be free of scale and contaminating iron particles, and the way that condition is reached becomes the surface finish. For TP309S, which mostly goes into hot service, the finish is usually chosen for cleanliness and inspection rather than appearance, but it still needs to be stated on the order so the mill and the receiving inspector are working to the same expectation.

  • Annealed and pickled — the standard mill finish for most sizes; matte and free of scale
  • Bright annealed — for smaller sizes where a clean, oxide-free bore is wanted; the anneal must still meet the Table 2 minimum
  • Blasted and pickled — common on heavier walls and larger diameters
  • Polished — by agreement where internal or external roughness is specified
  • Passivated — on request where the end-user specification asks for it

Inspection and Testing

Base inspection and testing for ASTM A312 TP309S combine chemistry, mechanical, and integrity checks, and the list below is the usual acceptance package. Supplementary requirements apply only when they are written on the purchase order.

  • Heat analysis — every heat against Table 1 for TP309S, including C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, Mo ≤0.75%
  • Product analysis — when ordered, using A480 Table A1.1 tolerances
  • Tension test — Table 4 tensile, yield, and elongation on a lot basis (75/30 ksi minima)
  • Flattening test — or the alternative bend where permitted, typically on 5% of the lot
  • Hydrostatic or electric test — every length; manufacturer’s option unless the order fixes the method
  • Visual and dimensional check — against the ordered size and the tolerance clauses

EN 10204 3.1 is the standard certificate from SHH STEEL supply. It reports the full Table 1 heat chemistry, the Table 4 results, the test method used on each length, and the heat-treatment condition. EN 10204 3.2 or third-party witness by SGS, Bureau Veritas, TÜV, or the buyer’s nominated agency is arranged when specified, and the inspector should be booked before final testing rather than after the pipe is packed.

Supplementary options worth considering for TP309S are summarized below; none of them applies unless the order names it.

Option Purpose
S1 product analysis Confirms chemistry on the finished pipe
S5 radiography Weld integrity on WLD pipe
S7 intergranular corrosion A262 Practice E check of the as-supplied condition
S8 minimum wall Wall ordered as minimum rather than nominal
S9 weld decay Compares weld and base-metal loss rates

On receipt, check the stencil reads TP309S or S30908 and not just “309,” then compare the certificate against the limits above. Confirm carbon is at or below 0.08% and that the test method for each length is stated. Positive material identification by optical emission on a sample length is a sensible extra when several 309-family grades share the same storage area, because handheld XRF cannot resolve carbon.

Packaging and Shipping

Packaging for ASTM A312 TP309S is chosen to keep the surface free of iron contamination and the ends protected through export transit. Each length carries the A312 marking required by clause 17, normally including the manufacturer, the specification, the grade, the manufacturing type, the size, the heat number, and the test method, and the packing list repeats those identifiers so bundles can be checked without unpacking.

  • End caps on all lengths; bevel protectors on beveled ends
  • Bundles strapped with non-metallic or covered straps to avoid contact with carbon steel
  • Wooden cases or crates for bright-annealed, polished, or thin-wall pipe
  • Moisture protection for sea freight on request
  • Packing lists that match heat numbers to bundle numbers

Why Choose SHH STEEL

SHH STEEL supplies specification-driven stainless pipe, and for ASTM A312 TP309S we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 chemistry, the Table 4 results, and the heat-treatment evidence the grade calls for, and we match the manufacturing route and size to the enquiry instead of pushing whatever is nearest on the shelf.

  • Clear reporting of the 0.08% carbon cap, chromium 22.0–24.0%, and nickel 12.0–15.0% on every certificate
  • Straight advice when a sister grade such as TP309H or TP309Cb would actually suit the service better
  • SML, WLD, and HCW routes with EN 10204 3.1 certificates; 3.2 inspection on request
  • Dual A312/SA-312 marking only when the purchase order asks for both standards
  • Cut lengths, beveling, and project packing coordinated on confirmed orders

If you are still choosing between 309-family grades, send the design temperature, the atmosphere, whether the line is welded heavily in fabrication, and whether shutdown condensate is expected. We will answer with the grade that fits that combination rather than the one whose name is closest to the datasheet.

Supply Capability

SHH STEEL can supply ASTM A312 TP309S / UNS S30908 stainless steel pipe to the edition and manufacturing type named on your enquiry. The table summarizes the routes, sizes, finishes, and documents we regularly quote for this grade, and it is a capability statement rather than a promise that every combination is in stock today.

Item SHH STEEL capability for TP309S
Standard ASTM A312 / A312M TP309S / UNS S30908
Manufacturing types SML, WLD, HCW
Size NPS 1/8 and up per ASME B36.19; special OD/wall by agreement
Schedules 5S, 10S, 40S, 80S and non-standard walls
Length SRL, DRL, or cut-to-length
Finish Annealed and pickled; blasted and pickled; bright annealed or polished by agreement
Testing Tension (75/30 ksi), flattening/bend, hydro or NDE per length; S1/S5/S7/S8/S9 on order
Documents EN 10204 3.1; third-party inspection / 3.2 on request
Trade terms FOB / CFR / CIF / EXW and other agreed Incoterms

Stock / Available sizes. The representative range for TP309S is set out in the Dimensions section: NPS 1/2–24 with Sch 10S, 40S, and 80S as typical, plus special OD × wall on enquiry. Selected common sizes may be available from stock or recent heats, while heavy-wall seamless, unusual schedules, and special cut lengths are normally mill-order. We do not invent stock lists or tonnage claims, so ask for a live check against your size list.

A good enquiry for this grade states the A312 edition, TP309S (UNS S30908), the manufacturing type, NPS or OD × wall with nominal or minimum wall, length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirement. With that information we can line up a mill slot or a stock allocation against your need date, and combining project sizes into one heat helps with chemistry consistency and mill minimums.

FAQ

Is ASTM A312 the same as ASME SA-312 for TP309S?
No. ASTM A312/A312M and ASME SA-312 are two independent standards, even though the referenced editions are closely aligned on Table 1 chemistry, Table 4 tensile values, and most testing language for TP309S. If the piping is built to the ASME Code, name both standards on the purchase order and ask for dual marking; otherwise order to ASTM A312 alone and do not treat the titles as synonyms.
What is the UNS number for ASTM A312 TP309S?
The UNS number is UNS S30908. It identifies the same chemistry across product forms, so plate to ASTM A240 and pipe to ASTM A312 can share it, but the pipe still has to be ordered and certified to A312. Put both the TP designation and the UNS number on the order and check that both appear on the certificate and the stencil.
What chemical composition defines TP309S pipe?
Table 1 of ASTM A312 sets C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, Mo ≤0.75%, with Mn ≤2.00%, Si ≤1.00%, P ≤0.045% and S ≤0.030%. Those limits apply to the heat analysis; product analysis, when ordered, uses the A480 Table A1.1 tolerances, which widen individual readings slightly but never replace the heat requirement.
What are the tensile requirements for ASTM A312 TP309S?
Table 4 requires 75 ksi [515 MPa] minimum tensile strength and 30 ksi [205 MPa] minimum yield strength, with elongation of 35% longitudinal and 25% transverse. These are the same floors as the other 309-family grades. There is no hardness maximum in Table 4, so any hardness limit for bending or expanding must be written on the order.
TP309S vs TP309H — which should I order?
TP309S caps carbon at 0.08% with no minimum and has no grain-size rule, which suits general oxidation service and easy fabrication. TP309H adds a 0.04–0.10% carbon band, ASTM grain size No. 6 or coarser, and a reheated anneal, which is what creep-range design usually relies on. If the design allowables assume an H grade, order the H grade rather than TP309S.
TP309S vs TP310S — which grade suits higher temperature?
The 310 family, with chromium 24.0–26.0% and nickel 19.0–22.0%, has more oxidation and scaling margin than the 309 family at 22.0–24.0% chromium, so TP310S is the more conservative choice for the hottest sections. The step between families is mainly about oxidation margin, not room-temperature strength, because both share the 75/30 ksi Table 4 floor. Choose by the actual atmosphere and metal temperature, and remember that the richer grade costs more and can be harder to source in special sizes.
What heat treatment applies to ASTM A312 TP309S pipe?
TP309S has no individual Table 2 row, so the default solution anneal at 1900 °F [1040 °C] minimum with water quench or other rapid cooling applies. As a non-H grade, seamless pipe may be direct quenched after hot forming when the temperature is at or above the solution minimum, and there is no grain-size requirement.
Seamless vs welded TP309S pipe — which is better?
Neither is better in general. Seamless suits heavy walls, high pressure, and line classes that exclude welded pipe, while welded pipe is economical on larger diameters and thinner walls and is common in furnace ducting. Both must meet the same Table 1 chemistry and Table 4 tensile values, and the choice should follow the design code and the inspection plan.
What filler metal is used to weld TP309S pipe?
Table 6 of ASTM A312 shows no AWS filler classification for TP309S, so the filler is chosen by agreement and recorded on the welding procedure specification. A matching 309-type filler is typical, with a richer filler for dissimilar joints, and the procedure should be qualified for the service temperature rather than copied from a room-temperature job.
Hydrostatic test vs NDE — which do I get on TP309S pipe?
Every length receives either a hydrostatic test or a nondestructive electric test, and the manufacturer chooses unless the purchase order specifies one. If your inspection plan depends on a particular method, write it on the order. Pipe NPS 10 and larger may ship marked “NH” only when the purchaser accepts a system test instead of the hydrotest.
What sizes of TP309S pipe can SHH STEEL supply?
SHH STEEL quotes TP309S across ASME B36.19 sizes, typically NPS 1/2–24 in Sch 10S, 40S, and 80S, plus special OD and wall by agreement. Some common sizes may come from stock or recent heats, while heavy-wall seamless and unusual sizes are mill-order. Send your size list for a live availability check.

Conclusion

ASTM A312 TP309S / UNS S30908 is the general-purpose, low-carbon-capped heat-resisting member of the 23Cr–13Ni family, with C ≤0.08%, Cr 22.0–24.0%, Ni 12.0–15.0%, Mo ≤0.75%, a 75/30 ksi Table 4 floor with 35% L / 25% T elongation, and a solution anneal at 1900 °F [1040 °C] minimum. It is ordered for heat, not for general corrosion, and it is not a drop-in for A312 TP309H. Put the manufacturing type, size and wall basis, finish, and the grade-specific evidence on the purchase order, then review the EN 10204 3.1 certificate before release. SHH STEEL can supply TP309S pipe to the edition you name; browse the sister grades on the A312/A312M hub, or send your size list to admin@steelspecs.com.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X