ASME SA312 UNS S31726 Stainless Steel Pipe | ASME SA312 Stainless Steel - SHH STEEL

ASME SA312 UNS S31726 Stainless Steel Pipe | SA 312/SA 312M

ASME SA312 UNS S31726 stainless steel pipe under SA-312/SA-312M (ASTM A312/A312M), no TP designation: SML, WLD, and HCW routes with Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%, 80/35 ksi minimums, and solution anneal at 1900 °F [1040 °C] minimum, supplied by SHH STEEL with EN 10204 3.1 MTCs.
Grade
UNS S31726
Standard
ASME SA312 / SA 312M (ASTM A312 / A312M)
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASME SA312 UNS S31726 Stainless Steel Pipe

ASME SA-312/SA-312M covers seamless, welded, and heavily cold-worked austenitic stainless steel pipe for high-temperature and general corrosive service. UNS S31726 appears in Table 1 with no TP designation, so the pipe is ordered, stencilled, and certified by its UNS number alone. It is a low-carbon 4–5% molybdenum austenitic strengthened with nitrogen (often called 317LMN-type). The Table 1 melting analysis is C ≤0.03%, Mn ≤2.00%, P ≤0.040%, S ≤0.030%, Si ≤1.00%, Cr 17.0–20.0%, Ni 13.5–17.5%, Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%. Molybdenum 4–5% gives the pitting and crevice resistance, while the intentional nitrogen both stabilises the austenite at that Mo level and lifts the yield floor to 35 ksi.

Table 4 sets a single tensile row of 80 ksi [550 MPa] tensile and 35 ksi [240 MPa] yield, with 35% longitudinal and 25% transverse elongation. For heat treatment, S31726 is not individually listed in Table 2, so the general 1900 °F [1040 °C] minimum solution anneal with rapid cooling applies. UNS S31726 is not an H grade, so there is no carbon floor, no Table 5 grain-size rule, and no H-grade reheat clause. Table 6 does not assign an AWS filler class to S31726 in the extract used for this page, so the consumable is by agreement and must be recorded on the WPS. Because nitrogen can be lost from the weld pool, fabricators usually select an overalloyed Mo-bearing filler and qualify the procedure on S31726 itself. The usual service niche is chloride-bearing chemical process, flue-gas desulfurization, and bleach-plant streams where the designer wants 4–5% Mo and the extra strength that nitrogen brings.

SHH STEEL can supply ASME SA312 UNS S31726 stainless steel pipe to the edition named on your enquiry, in seamless (SML), welded (WLD), and heavily cold-worked (HCW) routes. We work to ASME B36.19 schedules and to special OD and wall combinations by agreement, issue EN 10204 3.1 mill test certificates that report the full Table 1 row including Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%, and can dual-mark SA-312/A312 when heat analysis, anneal, mechanical tests, and marking satisfy both editions on the purchase order. Tell us NPS, wall or schedule, finish, length, and any supplementary tests when you enquire.

Common commercial names and how they map to the ordered product are listed below. Market shorthand is useful in conversation, but the purchase order and certificate should always carry the full SA-312/A312 designation plus UNS S31726 so receiving inspection has one unambiguous identity to check.

  • ASME SA312 UNS S31726 — preferred marking for ASME-code and dual-marked pipe (no TP name exists)
  • ASTM A312 UNS S31726 — same Table 1 and Table 4 rows when the ASTM edition is referenced
  • 317LMN-type — market shorthand for the nitrogen-bearing 4–5% Mo grade; confirm N 0.10–0.20% on the MTC
  • EN 1.4439 / X2CrNiMoN17-13-5 (approx.) — European near-equivalent; recheck every limit before dual certification

UNS S31726 is not a drop-in for ASME SA312 UNS S31725 Stainless Steel Pipe, ASME SA312 TP317L Stainless Steel Pipe, or ASME SA312 UNS S31727 Stainless Steel Pipe, even though these grades often appear together on the same bid list. Versus S31725, S31726 turns nitrogen from a ≤0.10% maximum into a required 0.10–0.20% range, opens chromium down to 17.0%, and lifts the tensile row from 75/30 to 80/35 ksi. Versus TP317L, it adds roughly one percent more molybdenum, a higher nickel window, and the nitrogen band. Versus S31727, S31726 has no intentional copper range (Cu ≤0.75% instead of 2.8–4.0%) and anneals at the ordinary 1900 °F minimum rather than 1975–2155 °F. Each has its own Table 1 row and Table 4 floor, so dual marking across them is rarely possible. For the full family overview see the ASME SA 312/SA 312M hub.

Manufacturing Types (SML / WLD / HCW)

ASME SA-312 allows three manufacturing routes for UNS S31726, and the choice is a purchase-order decision driven by design code, size, wall thickness, and inspection preference. The route never changes the chemistry: every heat must still meet Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75% together with the rest of the Table 1 row, and every length must be solution annealed at 1900 °F [1040 °C] minimum with rapid cooling before it leaves the mill.

  • Seamless (SML) — no welding at any stage. Usually preferred for heavier walls, smaller diameters, and critical process lines where the project specification excludes welded pipe.
  • Welded (WLD) — made from UNS S31726 strip or plate by automatic welding without filler metal, then annealed. Practical and economical for larger diameters and thinner walls, provided the plate heat itself meets the UNS S31726 row.
  • Heavily cold-worked (HCW) — welded pipe cold worked at least 35% in wall and weld before the final anneal, with the weld radiographed before cold work. Ordered when the buyer wants that route and its marking.

Every finished length is hydrostatically tested or nondestructively electrically tested, and the mill may choose the method unless the purchase order fixes one. Pipe NPS 10 and larger may be marked “NH” only when the purchaser agrees to a system test instead. In practice UNS S31726 is a made-to-order grade at most mills, with minimum melt quantities above those of commodity TP316L or TP317L, so grouping project sizes onto one heat helps both lead time and chemistry consistency. Confirm the route, edition, wall basis, and any corrosion or supplementary tests before the mill order is placed so the certificate matches the design basis.

Chemical Composition of SA312 UNS S31726

Melting analysis (heat / ladle analysis) — Table 1

Heat analysis for UNS S31726. Values are maximum unless a range is shown; ellipses (…) mean no requirement.

Element UNS S31726 melting analysis
Carbon (C) ≤ 0.03
Manganese (Mn) ≤ 2.00
Phosphorus (P) ≤ 0.040
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 17.0 – 20.0
Nickel (Ni) 13.5 – 17.5
Molybdenum (Mo) 4.0 – 5.0
Nitrogen (N) 0.10 – 0.20
Copper (Cu) ≤ 0.75

Source: SA-312 Table 1, UNS S31726. N is a required range.

Product analysis — A480/A480M Table A1.1 tolerances applied to Table 1

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.03 0.005 over ≤ 0.035
Manganese (Mn) ≤ 2.00 0.04 over ≤ 2.04
Phosphorus (P) ≤ 0.040 0.005 over ≤ 0.045
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 17.0 – 20.0 0.20 under / over 16.80 – 20.20
Nickel (Ni) 13.5 – 17.5 0.15 under / over 13.35 – 17.65
Molybdenum (Mo) 4.0 – 5.0 0.10 under / over 3.90 – 5.10
Nitrogen (N) 0.10 – 0.20 0.01 under / over 0.09 – 0.21
Copper (Cu) ≤ 0.75 0.05 over ≤ 0.80

Vs S31725: N range vs max; Cr starts at 17.0 vs 18.0; tensile 80/35 vs 75/30. Vs S31727: S31727 has Cu 2.8–4.0, Mo 3.8–4.5, Mn ≤1.00, and Table 2 1975–2155 °F. N product ±0.01 on 0.10–0.20. Mo ±0.10 on 4–5%. Cu ≤0.75 with +0.05 product. Omit N and the heat is not S31726.

When reviewing a certificate for UNS S31726, check every element in the Table 1 row rather than only chromium and nickel. The elements that define this grade, Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%, are exactly the ones a commodity 300-series heat will miss, and a missing or out-of-range value is a nonconformance even when tensile results look good. Product analysis, when ordered, is judged against the A480 tolerances shown above. Designers should take allowable stresses only from the governing code tables listed for UNS S31726, not from a neighbouring grade.

Mechanical Properties of SA312 UNS S31726

Property S31726
Tensile, min 80 ksi [550 MPa]
Yield, min 35 ksi [240 MPa]
Elongation 35% L / 25% T

Source: SA-312 Table 4 for UNS S31726. One tensile row applies regardless of wall thickness; no hardness maximum is asserted here and there is no Table 5 grain-size requirement because UNS S31726 is not an H grade.

The 80/35 ksi minimums are the values your receiving inspector should look for on the MTC, and they are not interchangeable with sister rows: S31725 is 75/30, S31726 is 80/35, S31727 is 80/36, S31730 is 70/25, and S32053 is 93/43 ksi. Base testing covers tension on a lot basis, flattening on a sample of lengths, and hydrostatic or electric testing of every length. Elevated-temperature tensile, impact, and hardness limits are purchase-order or construction-code options rather than base SA-312 requirements, so write them on the order if your piping class needs them.

Like other austenitics, UNS S31726 work-hardens during cold bending or expanding, so severe forming may need an intermediate anneal that again meets the 1900 °F [1040 °C] minimum practice. For pressure design, use the allowable stresses listed for UNS S31726 in the governing Section II Part D or project-code tables; copying TP316L or TP317L allowables into the calculation package is a common and avoidable error.

Dimensions and Tolerances

Dimensional supply for UNS S31726 pipe follows ASME B36.19 schedules for the common NPS and schedule combinations, with special OD and wall by agreement when an exchanger, header, or process skid needs a non-standard section. Outside-diameter variations follow ASTM A999/A999M, and wall-thickness variations follow SA-312 Table 3 as summarised below. State on the order whether wall is nominal or minimum (Supplementary S8), so the mill rolls to the interpretation your design assumed.

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%

Source: SA-312 Table 3; outside diameter variations per A999/A999M.

  • Lengths — single random, double random, or cut-to-length by agreement
  • Cut lengths — typically no more than 1/4 in. [6 mm] over unless a tighter band is ordered
  • Ends — plain or beveled; confirm bevel angle and root face when the WPS is already frozen

Many chemical-process buyers order UNS S31726 by OD × wall rather than by NPS and schedule, especially for exchanger and instrument lines. For thin schedules with socket-weld or threaded ends, check that the remaining wall is still adequate after the 12.5% under-tolerance. Jointers are not permitted unless the order allows them, and cut-to-length programmes should include an allowance for fit-up scrap so pieces do not arrive short.

Equivalent Grades

Equivalence for UNS S31726 is mainly an ASME/ASTM identity question. The governing pipe designation is ASME SA-312 UNS S31726, and any trade name, European number, or plate counterpart has to be mapped back to that Table 1 row before a mill is asked to dual-mark or substitute.

Designation Notes
ASME SA-312 UNS S31726 Governing pipe grade (no TP designation)
ASTM A312 UNS S31726 Same Table 1 / Table 4 when the ASTM edition is referenced
317LMN-type market shorthand for the nitrogen-bearing 4–5% Mo grade; confirm N 0.10–0.20% on the MTC
EN 1.4439 / X2CrNiMoN17-13-5 (approx.) European near-equivalent; recheck every limit before dual certification
SA-240 / A240 UNS S31726 Plate and sheet counterpart where listed—not a pipe specification

Related SA-312 grades on steelspecs.com include ASME SA312 UNS S31725 Stainless Steel Pipe, ASME SA312 TP317L Stainless Steel Pipe, and ASME SA312 UNS S31727 Stainless Steel Pipe. These pages sit close together because buyers often compare them, but none of them is an automatic equivalent of UNS S31726. European numbers and brand names are engineering maps only; if a project specification quotes one, ask the mill to certify against the SA-312 UNS S31726 row and list any extra European requirements separately on the order.

Heat Treatment and Delivery Condition

All SA-312 pipe is delivered in the solution-annealed condition. For UNS S31726, S31726 is not individually listed in Table 2, so the general 1900 °F [1040 °C] minimum solution anneal with rapid cooling applies. Because the grade is not an H grade, there is no grade-specific heat-treatment lot marking requirement and no grain-size test, but most process projects still ask for heat and lot identity on the stencil so traceability survives fabrication.

  • Solution anneal at 1900 °F [1040 °C] minimum — followed by rapid cooling in water or by other rapid means
  • No Table 5 grain-size rule — not an H grade
  • Pickled and passivated — free of scale and embedded iron, which matters for crevice resistance
  • Bright anneal — available by agreement when the end user requires a scale-free surface

The anneal temperature should be stated on the MTC, not just the words “solution annealed”, so that inspection can verify it against the 1900 °F [1040 °C] minimum requirement. Rapid cooling is what keeps the high-alloy structure free of chromium carbides and molybdenum-rich intermetallic phases, so a slow furnace cool is not acceptable even if tensile results pass. If pipe is hot-formed or heavily cold-formed during fabrication, plan a re-anneal to the same practice before it goes into corrosive service.

Corrosion Resistance

UNS S31726 is chosen for chloride-bearing chemical process, flue-gas desulfurization, and bleach-plant streams where the designer wants 4–5% Mo and the extra strength that nitrogen brings. Molybdenum 4–5% gives the pitting and crevice resistance, while the intentional nitrogen both stabilises the austenite at that Mo level and lifts the yield floor to 35 ksi. SA-312 does not publish corrosion rates or critical pitting temperatures for any grade, so the selection must be backed by process-licensor data, published alloy data, or project testing rather than by the specification itself.

In practice, most corrosion failures in this class of alloy trace back to fabrication rather than base-metal chemistry: heat tint left on weld roots, iron contamination from carbon-steel tools, chloride-bearing insulation, and crevices under gaskets or deposits. Ask for pickled and passivated delivery, keep UNS S31726 apart from carbon steel in storage and fabrication, and remove weld oxide before commissioning. When the corrosion case needs proof, order Supplementary S7 intergranular testing (ASTM A262 Practice E) or a project pitting test such as ASTM G48; neither is automatic under SA-312.

Applications of SA312 UNS S31726 Pipe

Buyers usually arrive at UNS S31726 after a corrosion review has ruled out commodity 316L or 317L but has not justified the cost of a nickel alloy. The table below shows typical uses; every application still needs confirmation of temperature, concentration, and chloride level against real data.

Application Why UNS S31726 Note
Chemical and acid process lines Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75% Confirm concentration and temperature
Flue-gas and scrubber systems Chloride-bearing condensate Watch deposits and crevices
Pulp and paper liquors Mixed chloride and oxidising chemistry Compare with sister UNS rows
Heat exchanger and instrument piping Corrosion margin over 317L Often seamless, ordered by OD × wall

If only moderate chloride resistance is needed, ASME SA312 TP317L Stainless Steel Pipe or ASME SA312 TP316L Stainless Steel Pipe are usually easier to source and cheaper. If the duty calls for full 6Mo performance, compare ASME SA312 UNS S31254 Stainless Steel Pipe before stretching a leaner heat into service it was not designed for. The right grade is the one your corrosion engineer and the governing code both support, and we are happy to quote alternatives side by side.

Weldability

UNS S31726 welds well with GTAW, GMAW, and SMAW when the procedure is qualified on the actual grade. Table 6 does not assign an AWS filler class to S31726 in the extract used for this page, so the consumable is by agreement and must be recorded on the WPS. Because nitrogen can be lost from the weld pool, fabricators usually select an overalloyed Mo-bearing filler and qualify the procedure on S31726 itself. Mill longitudinal welds on WLD and HCW pipe are autogenous, so the filler question applies only to fabrication welds.

Good practice for this alloy class is low heat input, controlled interpass temperature (commonly 150 °C or below), full back-purging with argon to keep the root bright, and removal of heat tint by pickling or mechanical cleaning. Molybdenum segregates in autogenous weld metal, so overalloyed filler is normally used for corrosion-critical joints rather than fusing the root without filler. Dissimilar joints to carbon steel need a transition procedure approved by the piping engineer.

Surface Finishes

Standard delivery for UNS S31726 is annealed and pickled, which gives a clean matte surface free of scale and embedded iron. Other finishes are available by agreement and should be written on the order with a clear measurement basis.

  • Annealed and pickled (AP) — standard process-piping finish
  • Bright annealed — scale-free surface from a protective atmosphere
  • Mechanically polished or electropolished — by agreement, with Ra target and OD/ID scope stated

For corrosion-critical service, the finish is less about appearance than about removing anything that could start a pit or crevice. If you need a polished or electropolished ID, specify the Ra value, whether it applies to OD, ID, or both, and whether it is measured before or after passivation, so that both mill and inspector are working to the same number.

Inspection and Testing

Base SA-312 testing for UNS S31726 covers heat analysis, tension tests, flattening tests, and hydrostatic or nondestructive electric testing of every length. Supplementary requirements such as product analysis, ultrasonic or radiographic weld examination, intergranular corrosion testing, or third-party witness apply only when written on the purchase order.

  • Chemistry — full Table 1 row on the MTC, including Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%
  • Tensile — 80/35 ksi with 35% L / 25% T elongation
  • Heat treatment — actual anneal temperature against 1900 °F [1040 °C] minimum
  • Integrity — hydrostatic or electric test result for each length
  • Options — PMI, EN 10204 3.2, S7 / G48 corrosion tests, UT/RT of welds

We recommend a positive material identification check on receipt for any UNS S31726 order, because the distinguishing elements are easy to verify with a portable analyser and a mixed-up length is far cheaper to catch before fabrication than after. When a third-party inspector is required, book the witness before final testing so the inspector sees the actual lengths being tested.

Packaging and Shipping

UNS S31726 pipe is packed to protect both the surface and the identity of each length. Typical export packing uses plastic end caps, wrapping or woven bags, and seaworthy wooden cases or bundles with stainless or non-metallic strapping, with heat number, size, and grade marked on each package.

  • Marking — SA-312 UNS S31726, manufacturing type, size, heat number, and edition on every length
  • Segregation — kept apart from carbon steel and from sister UNS grades in the same shipment
  • Documents — packing list and MTC numbers matching the stencil

Because several grades in this family look identical on the rack, we keep UNS S31726 physically separated from ASME SA312 UNS S31725 Stainless Steel Pipe and ASME SA312 TP317L Stainless Steel Pipe during packing and list each heat on the packing list. On arrival, receiving staff should check stencil, packing list, and certificate against each other before the pipe enters the fabrication shop.

Why Choose SHH STEEL

Grades like UNS S31726 are where specification detail decides whether a shipment is accepted. SHH STEEL reads the Table 1, Table 2, and Table 4 rows for the exact UNS on your enquiry, checks mill offers against them before quoting, and tells you openly where the standard is silent, such as Table 6 filler assignments, rather than filling gaps with guesses. Our aim is a certificate package your inspector can clear on the first review.

  • Specification fidelity — full Table 1 reporting including Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%, correct 80/35 ksi row, and anneal at 1900 °F [1040 °C] minimum
  • Mill sourcing — made-to-order melts for specialty UNS grades, with remnant stock checked for urgent small lots
  • Certification — EN 10204 3.1 as standard, 3.2 and third-party witness by agreement, dual SA-312/A312 when both editions are met
  • Honest limits — we state where SA-312 is silent and where a sister grade would serve you better
  • Export packing — capped, segregated, and documented for ocean freight

Supply Capability

We supply ASME SA312 UNS S31726 pipe for project and maintenance orders, from single lengths for replacement work to full heats for new process units. The summary below shows our normal range; anything outside it can usually be arranged by agreement with the mill.

Item Capability
Grade ASME SA312 / ASTM A312 UNS S31726 (no TP designation)
Manufacturing types Seamless (SML), welded (WLD), heavily cold-worked (HCW)
Sizes ASME B36.19 schedules plus special OD × wall by agreement
Heat treatment Solution annealed at 1900 °F [1040 °C] minimum, rapid cooled
Certification EN 10204 3.1; 3.2 / third-party by agreement
Testing options PMI, product analysis, UT/RT, S7 / G48 corrosion tests

Because UNS S31726 is rarely held as open stock, most orders are made to order, and lead time depends on the next available melt campaign. Small urgent quantities can sometimes be met from remnant lengths of earlier certified heats, so it is always worth asking. Send us the edition, sizes, quantities, manufacturing type, and any supplementary tests, and we will come back with a clear offer and delivery estimate.

FAQ

Is ASME SA312 the same as ASTM A312?
For chemistry (Table 1), tensile (Table 4), manufacturing types, and most testing language, ASME SA-312/SA-312M matches ASTM A312/A312M of the referenced edition. Dual SA312/A312 marking of UNS S31726 is common when ordered. Name both editions on the purchase order and the mill test certificate so inspectors can verify the heat against the exact books you cited.
What is the UNS number for this grade, and is there a TP name?
Table 1 lists S31726 as the unified number for this pipe grade with an ellipsis in the TP column, so there is no TP designation. Cite UNS S31726 on the purchase order, stencil, packing list, and mill test certificate so that chemistry and tensile rows cannot be confused with a neighbouring grade that shares a similar commercial nickname.
UNS S31726 vs UNS S31725 — which should I order?
Both rows share Mo 4.0–5.0%, Ni 13.5–17.5%, and Cu ≤0.75%. S31726 requires nitrogen 0.10–0.20% and carries 80/35 ksi minimums; S31725 caps nitrogen at 0.10% and stays at 75/30 ksi. If your design allowables were taken from S31726, a 75/30 ksi S31725 certificate is not acceptable, so order the exact UNS on the datasheet.
UNS S31726 vs TP317L — which should I order?
TP317L is Mo 3.0–4.0% with no nitrogen requirement and lower tensile minimums. S31726 adds about one percent more molybdenum, a higher nickel window, and nitrogen 0.10–0.20%, giving 80/35 ksi. Choose S31726 when the corrosion case or the wall-thickness calculation needs it; switching later is a material change rather than a free substitution.
Seamless vs welded UNS S31726 — which is better?
Neither is universally better. Seamless suits heavier walls and services where the project excludes welded pipe, while welded pipe is economical for larger diameters and thinner walls. Both are legitimate SA-312 forms and both must meet the full UNS S31726 chemistry and anneal. State SML, WLD, or HCW on the order and check the same letters on the marking.
Can you dual-certify SA312 / A312 UNS S31726?
Yes, when heat analysis (including Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%), the solution anneal, mechanical tests on the 80/35 ksi row, and marking meet both editions named on the order. Write the ASME and ASTM edition years on the purchase order and require the MTC to reference both, so receiving inspection can clear the heat without a second paperwork chase.
Hydrostatic test or NDE — which will I get?
Each length is either hydrostatically tested or nondestructively electrically tested, and the manufacturer may choose unless the purchase order fixes the method. If your piping class or client specification requires one method, state it on the order and check that the chosen test is recorded on the MTC for every length supplied.
What heat treatment applies to UNS S31726?
S31726 is not individually listed in Table 2, so the general 1900 °F [1040 °C] minimum solution anneal with rapid cooling applies. It is not an H grade, so there is no grain-size requirement or H-grade reheat clause. Ask the mill to show the actual anneal temperature on the certificate rather than just the words solution annealed.
What Table 1 chemistry defines UNS S31726?
Table 1 sets C ≤0.03%, Mn ≤2.00%, P ≤0.040%, S ≤0.030%, Si ≤1.00%, Cr 17.0–20.0%, Ni 13.5–17.5%, Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%. These are melting-analysis limits from the ordered edition; product analysis, when required, uses the A480 tolerances. Check that every element is reported, because the distinguishing elements are exactly the ones a commodity 300-series heat would miss.
What are the Table 4 tensile requirements for UNS S31726?
Table 4 sets tensile strength of 80 ksi [550 MPa] minimum and yield strength of 35 ksi [240 MPa] minimum, with 35% longitudinal and 25% transverse elongation. A single row applies regardless of wall thickness. Use the allowable stresses listed for UNS S31726 in the governing code, not those of a sister grade with a different tensile row.
What filler metal should I use to weld UNS S31726 pipe?
Table 6 does not assign an AWS filler class to S31726 in the extract used for this page, so the consumable is by agreement and must be recorded on the WPS. Because nitrogen can be lost from the weld pool, fabricators usually select an overalloyed Mo-bearing filler and qualify the procedure on S31726 itself. Qualify the procedure on the actual grade, use low heat input and full back-purging, and remove heat tint after welding so the joint keeps its corrosion resistance.
Why are the tensile minimums 80/35 ksi for UNS S31726?
Table 4 assigns S31726 a tensile minimum of 80 ksi [550 MPa] and yield minimum of 35 ksi [240 MPa], with 35% longitudinal and 25% transverse elongation. The higher floor reflects the required 0.10–0.20% nitrogen. Reject certificates that only show the 75/30 ksi row, because that belongs to S31725 and would not support S31726 design allowables.

Conclusion

ASME SA312 UNS S31726 is a TP-less low-carbon 4–5% molybdenum austenitic strengthened with nitrogen (often called 317LMN-type), defined by Mo 4.0–5.0%, N 0.10–0.20%, and Cu ≤0.75%, a 80/35 ksi tensile row, and a solution anneal at 1900 °F [1040 °C] minimum. Order it by UNS number, check every Table 1 element and the anneal temperature on the certificate, and compare it carefully with ASME SA312 UNS S31725 Stainless Steel Pipe and ASME SA312 TP317L Stainless Steel Pipe before accepting any substitution. For stock, mill certificates, or a quotation on SA312 UNS S31726 pipe, contact admin@steelspecs.com or browse the ASME SA 312/SA 312M category.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X