ASTM A312 TP XM-10 Stainless Steel Pipe | ASTM A312 Stainless Steel - SHH STEEL

ASTM A312 TP XM-10 Stainless Steel Pipe

ASTM A312 TP XM-10 / UNS S21900 high-manganese nitrogen-strengthened stainless steel pipe in SML, WLD and HCW, with Mn 8.0–10.0%, N 0.15–0.40%, a 90/50 ksi Table 4 floor and a 1900 °F solution anneal, supplied by SHH STEEL with EN 10204 3.1 MTCs.
Grade
TPXM-10 / UNS S21900
Standard
ASTM A312 / A312M
Product form
Seamless (SML), welded (WLD), and heavily cold-worked (HCW) stainless steel pipe
Outside diameter
ASME B36.19 schedules (commonly Sch 5S / 10S / 40S / 80S) and special OD/wall by agreement; typical NPS from 1/8 upward (confirm on enquiry)
Share:
Overview
Manufacturing Types
Chemical Composition
Mechanical Properties
Specification
Equivalent Grades
Heat Treatment
Corrosion Resistance
Applications
Weldability
Surface Finishes
Inspection and Testing
Packaging and Shipping
Why Choose SHH STEEL
Supply Capability
FAQ
Conclusion

What is ASTM A312 TP XM-10 Stainless Steel Pipe

A312/A312M is the ASTM product specification for seamless, welded, and heavily cold-worked austenitic stainless steel pipe intended for high-temperature and general corrosive service. It stands on its own as an ASTM standard, and this page is written against it. TPXM-10 (UNS S21900) is one of the less common rows in its Table 1, and that is exactly why buyers ask us to spell out what the specification actually fixes for this alloy and what is left to agreement between purchaser and mill.

TPXM-10 belongs to the chromium-manganese-nitrogen group of A312 grades. Instead of relying on 8–10% nickel for its austenite, it uses 8.0–10.0% manganese and up to 0.40% nitrogen with only 5.5–7.5% nickel, and the nitrogen is what lifts the Table 4 floor to 90 ksi tensile and 50 ksi yield, well above the 75/30 ksi of TP304. Buyers usually come to it for strength per kilogram of pipe, for the lean-nickel cost profile, or because a drawing or legacy specification already names it.

SHH STEEL can supply ASTM A312 TPXM-10 pipe as seamless (SML), welded (WLD), or heavily cold-worked (HCW) product, in ASME B36.19 stainless schedules or special OD and wall by agreement, with EN 10204 3.1 mill test certificates that report the full Table 1 heat analysis, the Table 4 tension results, and the heat-treatment record. Where a purchase order also asks for ASME SA-312 marking, dual marking can be offered on heats that qualify under both documents, but the ASTM grade remains the one this page describes.

On enquiries the grade appears as XM-10, TP XM-10, 21-6-9, or simply S21900, and all of those should be translated back to the A312 row before a quote is made. The trade name is market shorthand rather than a requirement, so the order and certificate should carry ASTM A312 TPXM-10 and UNS S21900 together, which also prevents confusion with the low-carbon TPXM-11 that shares almost every other limit.

If TPXM-10 turns out not to be the right fit, the closest sister pages in the same ASTM series are A312 TPXM-11, A312 TPXM-19, A312 TPXM-29, A312 UNS S20400, and A312 TP304. All A312 grades are collected on the A312/A312M hub, so a short list can be compared against one standard before the enquiry goes out.

Manufacturing Types (SML / WLD / HCW)

ASTM A312 allows three manufacturing routes for TPXM-10 pipe, and the route is a purchase-order decision rather than a property of the grade. Whichever route is chosen, the heat must still meet the same Table 1 limits (C ≤0.08%, Mn 8.0–10.0%, Cr 19.0–21.5%, Ni 5.5–7.5%, and N 0.15–0.40%), the same Table 4 tension floor, and the same 1900 °F [1040 °C] minimum solution anneal (Table 2 default) with rapid cooling heat-treatment requirement before any length is released.

  • Seamless (SML) pierced and hot or cold finished, chosen for heavy wall, high pressure, or owner specifications that exclude a weld seam
  • Welded (WLD) formed from flat-rolled product and welded without filler or with filler where the edition allows, economical in thinner walls and larger diameters
  • Heavily cold-worked (HCW) welded pipe given at least 35% cold reduction of the weld and base metal before the final anneal, which refines the weld structure toward seamless behaviour

TPXM-10 is a niche grade, so seamless and welded availability depends more on mill campaign than on the size table, and small quantities are often seamless because a welded campaign needs strip of the same heat. Tell us which route your design code or client specification accepts, because a quotation that leaves the route open forces the mill to choose and can create disputes at receiving inspection.

Chemical Composition of ASTM A312 TPXM-10

The melting analysis in Table 1 is what the heat must meet when it is cast, and it is the first table a reviewer should compare against the mill certificate. For TPXM-10 (UNS S21900) the defining limits are C ≤0.08%, Mn 8.0–10.0%, Cr 19.0–21.5%, Ni 5.5–7.5%, and N 0.15–0.40%. The table below reproduces the Table 1 row as published, with elements carrying no requirement shown as such rather than filled with invented values.

Element TPXM-10 (UNS S21900) melting analysis
Carbon (C) ≤ 0.08
Manganese (Mn) 8.0 – 10.0
Phosphorus (P) ≤ 0.045
Sulfur (S) ≤ 0.030
Silicon (Si) ≤ 1.00
Chromium (Cr) 19.0 – 21.5
Nickel (Ni) 5.5 – 7.5
Nitrogen (N) 0.15 – 0.40
Molybdenum (Mo) … (no requirement)

The manganese and nitrogen ranges are the two lines to check first, because they carry the strength. A heat at the bottom of the nitrogen band still has to meet 50 ksi yield, so mills typically aim well inside the 0.15–0.40% range. Carbon is capped at 0.08% here, which is the main difference from TPXM-11, and molybdenum carries no requirement at all.

Product analysis is a separate check made on the finished pipe, and ASTM A312 refers it to the permitted variations in ASTM A480 Table A1.1. The second table adds those tolerances to the melt limits so you can see the band that a check analysis on the pipe is allowed to fall within when Supplementary Requirement S1 or an owner check is ordered.

Element Melting (Table 1) Tolerance (A480 A1.1) Product analysis limit
Carbon (C) ≤ 0.08 0.01 over ≤ 0.09
Manganese (Mn) 8.0 – 10.0 0.06 under / over 7.94 – 10.06
Phosphorus (P) ≤ 0.045 0.010 over ≤ 0.055
Sulfur (S) ≤ 0.030 0.005 over ≤ 0.035
Silicon (Si) ≤ 1.00 0.05 over ≤ 1.05
Chromium (Cr) 19.0 – 21.5 0.20 under / 0.25 over 18.80 – 21.75
Nickel (Ni) 5.5 – 7.5 0.10 under / over 5.40 – 7.60
Nitrogen (N) 0.15 – 0.40 0.01 under / 0.04 over 0.14 – 0.44

Read the product limits as acceptance bounds for a check analysis only. A heat that sits outside the Table 1 melt range is non-conforming even if a later product analysis lands inside the widened band, so the certificate should always show the ladle analysis first.

Mechanical Properties of ASTM A312 TPXM-10

Table 4 sets the room-temperature tension requirements for TPXM-10: 90 ksi [620 MPa] tensile strength and 50 ksi [345 MPa] yield strength minimum, with elongation of 35% longitudinal / 25% transverse minimum. The table below shows those values in the form used on the specification, and the mill certificate should report actual results against each line.

Property TPXM-10 requirement (Table 4)
Tensile strength, min 90 ksi [620 MPa]
Yield strength (0.2% offset), min 50 ksi [345 MPa]
Elongation in 2 in. or 50 mm (or 4D) 35% longitudinal / 25% transverse, min

The 50 ksi yield is the number that makes TPXM-10 worth ordering, because a design that uses it can carry the same pressure on a thinner wall than TP304, provided the governing code lists allowable stresses for S21900 at the design temperature. Elongation is the same 35% longitudinal and 25% transverse that applies to most A312 grades, which shows that the extra strength is not bought at the expense of ductility.

No hardness maximum is set for this grade in Table 4, so a hardness figure on a certificate is information rather than an acceptance criterion unless your order adds one. If a project specification imposes hardness or impact testing, write it on the purchase order so the mill can plan the test pieces before the pipe is cut.

Dimensions, Tolerances and Stock Sizes

Dimensions for ASTM A312 TPXM-10 pipe are normally ordered by NPS and schedule from ASME B36.19, or by outside diameter and wall where the design calls for a non-standard size. Outside-diameter tolerance and wall tolerance come from the specification itself, and wall is read as nominal unless Supplementary Requirement S8 asks for minimum wall. The permitted variations in wall thickness from Table 3 are shown below by NPS band and wall-to-diameter ratio.

NPS designator Wall over Wall under
1/8 to 2-1/2 incl., all t/D 20.0% 12.5%
3 to 18 incl., t/D up to 5% 22.5% 12.5%
3 to 18 incl., t/D over 5% 15.0% 12.5%
20 and larger, welded, all t/D 17.5% 12.5%
20 and larger, seamless, t/D up to 5% 22.5% 12.5%
20 and larger, seamless, t/D over 5% 15.0% 12.5%

In practice the under-tolerance of 12.5% is the figure that matters for pressure design, because the designer has already sized the nominal wall with that allowance in mind. The over-tolerance varies with NPS and the wall-to-diameter ratio, which matters more for fit-up and weld preparation than for strength. For TPXM-10, whose higher strength or special chemistry often justifies a lighter or more closely engineered wall, confirm whether your calculation assumed nominal or minimum wall before the order is placed.

Stock / Available sizes. The table below shows the representative size band we quote for ASTM A312 TPXM-10, with example OD × wall combinations taken from B36.19 schedules. It is a supply and stock-enquiry range rather than a promise that every size sits on the floor today: for TPXM-10 the realistic expectation is that small-bore Sch 10S and 40S may be found as existing material, while most other sizes are mill orders tied to a melt campaign. Special OD, special wall, and cut lengths are always handled on enquiry.

Representative size Example OD × wall Typical schedules / notes
NPS 1/2 – 2 21.34 × 2.77 mm (NPS 1/2 Sch 40S); 60.33 × 3.91 mm (NPS 2 Sch 40S) Sch 10S / 40S / 80S; small-bore process and instrument take-offs
NPS 2-1/2 – 6 88.90 × 5.49 mm (NPS 3 Sch 40S); 168.28 × 3.40 mm (NPS 6 Sch 10S) Sch 10S / 40S / 80S; the most frequent enquiry band
NPS 8 – 12 219.08 × 8.18 mm (NPS 8 Sch 40S); 323.85 × 4.57 mm (NPS 12 Sch 10S) Sch 10S / 40S; confirm SML or WLD route on enquiry
NPS 14 – 24 406.40 × 4.78 mm (NPS 16 Sch 10S); 609.60 × 9.53 mm (NPS 24 Sch 40S) Sch 10S / 40S; usually mill-order, mostly welded
Special OD × wall Any OD and wall the mill can qualify On enquiry: state OD, nominal or minimum wall, and length practice

Read the example sizes as orientation for writing the enquiry, not as a price list. When you send a size list we check live availability line by line, separate what can ship from existing material from what needs a mill slot, and give the lead time for each group so the purchase order can be split if the schedule demands it.

Equivalent Grades

Buyers often arrive with a trade name, a plate designation, or a European number rather than the A312 row. The table below maps the names we see on enquiries for TPXM-10, but only the ASTM A312 grade and UNS number are contractual on this page; everything else is a cross-reference that needs checking against its own standard.

Designation Notes
ASTM A312 TPXM-10 / UNS S21900 Governing grade on this page
ASME SA-312 TPXM-10 Separate Code standard; dual mark only when the order names both
XM-10 / 21-6-9 Market names; confirm the full Table 1 row
ASTM A312 TPXM-11 / S21904 Low-carbon sister, not interchangeable without review
EN / JIS No one-to-one equivalent asserted

The ASME SA-312 row is listed because some Code projects require it, not because it is a synonym. ASME SA-312 is a separate standard adopted into the Boiler and Pressure Vessel Code, and the SA312 TPXM-10 page covers that document on its own terms. When both marks are wanted, the order should name both specifications and their editions so the certificate can state compliance with each.

Heat Treatment and Delivery Condition

TPXM-10 has no individual row in Table 2, so it falls under the default for all grades not individually listed: solution anneal at 1900 °F [1040 °C] minimum, then quench in water or cool rapidly by other means fast enough to prevent carbide reprecipitation. That capability is only demonstrated by ASTM A262 Practice E when Supplementary Requirement S7 is ordered. Seamless pipe may be quenched directly after hot forming if its temperature is not below the Table 2 minimum, and because carbon can reach 0.08% the rapid cool matters for this grade.

Delivery condition for TPXM-10 is solution annealed, then descaled by pickling or by blasting and pickling, straightened, and cut to the ordered length practice. HCW pipe receives its cold reduction before the final anneal, so cold work is never the delivered condition. Ask for the actual annealing temperature and cooling method to be recorded on the certificate, because a reviewer cannot otherwise confirm the Table 2 requirement from the document alone.

Corrosion Resistance

ASTM A312 contains no corrosion table, so the following is engineering commentary rather than a specification requirement. TPXM-10 has chromium in the 19–21.5% range, so its general corrosion behaviour in atmospheric, fresh-water, and mildly oxidizing service is broadly in the region of the 304 family, and nitrogen helps pitting resistance a little. It contains no molybdenum, so it is not a substitute for 316 in chloride-bearing process water.

With carbon allowed up to 0.08%, the heat-affected zone of a heavy multipass weld can sensitize if the joint stays in the sensitizing range for long, which is why S7 intergranular testing or the low-carbon TPXM-11 is worth considering for welded aqueous service. Stress corrosion cracking in hot chlorides remains a risk, as it is for other austenitic grades, so warm chloride service needs a corrosion review.

Applications of ASTM A312 TPXM-10 Pipe

Applications for ASTM A312 TPXM-10 pipe follow its strength and lean-nickel profile rather than any special corrosion property. The table below lists where buyers have typically placed the grade, and each line assumes the code allowables for S21900 have been checked first.

Application area Typical use of TPXM-10 pipe Selection note
Pressure piping Lines where 90/50 ksi floors permit thinner walls under the applicable code Use code allowable stresses for S21900
Process and utility Water, air, and mild chemical service ordered to A312 Confirm fluid compatibility; no Mo
Low-temperature service Austenitic piping where toughness at low temperature is needed Confirm code impact-test exemptions for the grade
Structural / mechanical tube use Supports and frames needing high yield stainless Order A312 when pipe documentation is required
OEM / skid fabrication Spools where strength and austenitic weldability both matter Document filler by agreement on the WPS
General corrosive service Mild environments without heavy chlorides Prefer TP316/TP316L or TPXM-19 if chlorides dominate

Treat the table as a starting point for discussion with the process licensor or corrosion engineer, not as an approval. Code allowable stresses, temperature limits, and any owner material lists decide whether TPXM-10 is acceptable on a given line, and those checks should be made before the pipe is ordered rather than after it arrives.

Weldability

TPXM-10 welds with the normal austenitic processes, including GTAW for roots and thin walls, GMAW for fill passes on heavier walls, SMAW for field joints, and orbital GTAW for repetitive girth welds. Because the base metal is nitrogen strengthened, the weld metal can easily undermatch Table 4 if a common 308-type consumable is used. S21900 is not listed in Table 6, so the standard names no AWS A5.9 class and filler selection is by agreement, recorded on the WPS.

Qualify the procedure on TPXM-10 itself rather than on a convenient 304 coupon, because the qualification has to demonstrate the strength and soundness of this chemistry. Clean joint preparation, controlled heat input and interpass temperature, and a back-purged root are the normal baseline; the certificate for any WLD pipe should also state whether filler metal was used in the longitudinal seam.

Surface Finishes

Surface condition for ASTM A312 TPXM-10 pipe should be stated on the purchase order rather than left to mill default. On stainless pipe, residual scale, embedded free iron, and chloride contamination from handling can matter as much as the nominal finish name, and they are far easier to prevent at the mill than to correct on site.

  • Annealed and pickled the standard delivery after solution treatment for process piping
  • Blasted and pickled when heavier scale needs mechanical help before chemical descaling
  • Bright annealed by agreement, generally on smaller sizes where the furnace atmosphere can be controlled
  • Passivated or polished by agreement, with the method and acceptance criteria written on the order

For TPXM-10, the high manganese content gives a slightly darker pickled surface than 304, which is cosmetic and not a defect. If the line will be inspected for surface iron, specify the test method at the enquiry stage so that the packing and handling plan supports it.

Inspection and Testing

The base acceptance package for ASTM A312 TPXM-10 pipe combines heat analysis, tension testing, the flattening or bend test that applies to the manufacturing type, and a hydrostatic or non-destructive electric test on every length. Visual and dimensional inspection confirm the size and surface before marking. For TPXM-10 the certificate lines worth checking first are manganese, nitrogen, and the 50 ksi yield, since those are the values that distinguish it from a mislabelled 304 heat.

Supplementary requirements are optional until they are written on the order. The options buyers request most often for this grade are summarized below, and each one adds test time that should be allowed for in the delivery schedule.

Option Purpose
S1 product analysis Confirms chemistry on finished pipe
S5 radiography Weld integrity on WLD pipe
S7 intergranular corrosion A262 Practice E after sensitizing treatment
S8 minimum wall Wall interpreted as minimum rather than nominal
S9 weld decay Compares weld and base-metal loss rates

Third-party inspection, witness points, and EN 10204 3.2 certification are available when the order names the inspection agency. Agree the hold points before production starts, because witnessing a hydrotest or a tension test after the fact is not possible.

Packaging and Shipping

ASTM A312 TPXM-10 pipe is packed for handling and for ocean or land transport. Each length is marked with ASTM A312, the grade TPXM-10 / UNS S21900, the manufacturing type, size, heat number, and the test method used, with SA-312 added only when the order asks for dual marking. Bundle lists repeat the heat numbers so receiving can match pipe to certificates without opening every wrap.

  • End caps or bevel protectors fitted as ordered
  • Bundles strapped with protected contact points to limit iron pick-up
  • Wooden cases or seaworthy bundles for export, with moisture protection for sea freight
  • Small-bore or polished pipe cased separately where damage risk is higher

Stainless pipe should not be stored or lifted in contact with carbon steel, and for a specialty grade such as TPXM-10 it is worth keeping the material segregated by heat on arrival, since mixing it with common 304 stock is the most frequent cause of misuse on site.

Why Choose SHH STEEL

SHH STEEL supplies specification-driven stainless pipe, and for a specialty grade such as ASTM A312 TPXM-10 we quote against the edition you name rather than a generic catalogue sheet. We report the full Table 1 heat analysis, the Table 4 tension results, and the heat-treatment record, and we tell you early when a size or route is a mill order instead of letting the lead time surprise you.

  • Experience with lean-nickel Cr-Mn-N grades, including the yield-strength and filler-matching questions they raise
  • Clear advice on sister grades under ASTM A312, so TPXM-10 is not confused with a commoner alloy that looks similar on paper
  • Honest separation of specification requirements from producer or market guidance in every document we send
  • EN 10204 3.1 certificates as standard, with third-party inspection and 3.2 certification on request

The aim is a delivery that clears receiving inspection on the first review. That means the certificate, the stencil, and the purchase order all say the same thing about grade, UNS number, manufacturing type, size, and heat treatment, and that any agreed variation is written down before the pipe is made.

Supply Capability

SHH STEEL can supply ASTM A312 TPXM-10 stainless steel pipe against the edition and manufacturing type named on your enquiry. The capability table below summarizes the routes, sizes, finishes, and documents we regularly quote for this grade, and each line can be narrowed to your project specification.

Item SHH STEEL capability for TPXM-10
Standard ASTM A312 / A312M, TPXM-10 / UNS S21900
Manufacturing types SML, WLD, HCW
Size NPS 1/8 and up per ASME B36.19; special OD and wall by agreement
Schedules 5S, 10S, 40S, 80S and non-standard walls
Length Single random, double random, or cut to length
Heat treatment 1900 °F [1040 °C] minimum solution anneal (Table 2 default) with rapid cooling
Filler guidance Not listed in Table 6; filler by agreement, recorded on the WPS
Testing Tension (90/50 ksi), flattening or bend, hydrostatic or electric test per length; S1, S5, S7, S8, S9 on order
Documents EN 10204 3.1 with full Table 1 analysis; 3.2 and third-party inspection on request
Trade terms FOB, CFR, CIF, EXW and other agreed Incoterms

Stock / Available sizes. The representative band for TPXM-10 is NPS 1/2 to 24 in Sch 10S, 40S, and 80S as listed under Dimensions. Selected common OD × wall combinations may be available from existing material, while heavy-wall seamless, unusual schedules, and special cut lengths are normally mill orders. We do not publish stock part numbers or tonnage claims for this grade; ask for a live check against your size list instead.

Enquiries move fastest when they state the A312 edition, TPXM-10 / UNS S21900, the manufacturing type, NPS or OD × wall (and whether the wall is nominal or minimum), length practice, finish, and any product-analysis, corrosion-test, or 3.2 requirements. Dual SA-312 marking, bevelled ends, and cut lengths are available on confirmed orders when the order says so.

FAQ

Is ASTM A312 TPXM-10 the same as ASME SA-312 TPXM-10?
They are two independent standards. ASTM A312/A312M is the ASTM product specification, and ASME SA-312 is the separate document adopted into the Boiler and Pressure Vessel Code. The technical rows for UNS S21900 are closely aligned in current editions, but a pipe is only certified to the document named on the order, so when both are needed the purchase order should list both specifications and editions and the certificate should state compliance with each.
What is the UNS number for ASTM A312 TPXM-10?
ASTM A312 TPXM-10 is UNS S21900, and the market often calls it 21-6-9 after its nominal chromium, nickel, and manganese levels. The UNS number should appear on the mill certificate and on the stencil next to the ASTM A312 mark, because a trade name alone makes it hard for receiving inspection to tie the chemistry on the certificate to the pipe in the rack.
What are the tensile and yield requirements for ASTM A312 TPXM-10 pipe?
Table 4 requires 90 ksi [620 MPa] tensile strength and 50 ksi [345 MPa] yield strength minimum, with elongation of 35% longitudinal / 25% transverse minimum. These are room-temperature minimums for acceptance only; design allowables at temperature come from the applicable piping code, and they should be checked there before a wall thickness is fixed.
What heat treatment does ASTM A312 TPXM-10 pipe receive?
TPXM-10 is not individually listed in Table 2, so the default applies: solution anneal at 1900 °F [1040 °C] minimum and quench in water or cool rapidly by other means. The delivered condition is solution annealed and descaled, and the certificate should record the actual annealing temperature and the cooling method so a reviewer can confirm the requirement without asking the mill.
Which filler metal is used to weld ASTM A312 TPXM-10?
S21900 is not listed in Table 6, so ASTM A312 assigns no AWS A5.9 classification and the filler is chosen by agreement; a high-manganese nitrogen-bearing consumable is the usual way to avoid undermatching the 90/50 ksi base metal. Whatever is chosen should be recorded on the WPS and PQR, and the procedure should be qualified on TPXM-10 base metal so that the joint strength and soundness are demonstrated on the real chemistry.
Is ASTM A312 TPXM-10 pipe available seamless and welded?
Yes. ASTM A312 allows seamless (SML), welded (WLD), and heavily cold-worked (HCW) pipe for TPXM-10, all meeting the same chemistry, tension, and heat-treatment rules. Seamless is usual for heavy wall and high pressure, while welded is often more economical in thin walls and larger diameters; state the accepted route on the order.
What sizes of ASTM A312 TPXM-10 pipe can SHH STEEL supply?
We quote NPS 1/2 to 24 in Sch 10S, 40S, and 80S as the representative band, plus NPS 1/8 and up and special OD and wall by agreement. Some common sizes may be available from existing material, while heavy-wall seamless and unusual schedules are normally mill orders, so send a size list for a live check.
What documents come with ASTM A312 TPXM-10 pipe?
Each shipment carries an EN 10204 3.1 mill test certificate showing the A312 edition, TPXM-10 / UNS S21900, manufacturing type, heat number, the full Table 1 heat analysis, Table 4 tension results, heat treatment, and the hydrostatic or electric test. Third-party inspection and 3.2 certification can be added when the order names the agency.
What is the difference between TPXM-10 and TPXM-11 under ASTM A312?
The two grades share the same manganese, chromium, nickel, and nitrogen ranges and the same 90/50 ksi Table 4 floor. The difference is carbon: TPXM-10 allows up to 0.08%, while TPXM-11 is limited to 0.04%. Choose TPXM-11 when heavy welding or sensitization risk matters, and TPXM-10 when that margin is not needed.
Why is TPXM-10 stronger than TP304 pipe?
TPXM-10 carries 0.15–0.40% nitrogen in solid solution, which raises yield strength far more effectively than nickel, and its 8–10% manganese allows that much nitrogen to stay dissolved. The result is a Table 4 floor of 90 ksi tensile and 50 ksi yield, compared with 75 ksi and 30 ksi for TP304.
Can TPXM-10 replace TP316 in chloride service?
Not without a corrosion review. TPXM-10 has no molybdenum requirement, so its pitting and crevice resistance in chloride-bearing water is closer to the 304 family than to 316. If the line sees chlorides, compare it against TP316 or the molybdenum-bearing TPXM-19, which combines high strength with 1.50–3.00% Mo.

Conclusion

ASTM A312 TPXM-10 (UNS S21900) is the high-manganese, nitrogen-strengthened 21-6-9 grade of the series, ordered when a 90/50 ksi floor and a lean-nickel chemistry are worth more than a common alloy. The specification fixes C ≤0.08%, Mn 8.0–10.0%, Cr 19.0–21.5%, Ni 5.5–7.5%, and N 0.15–0.40%, a Table 4 floor of 90 ksi [620 MPa] tensile and 50 ksi [345 MPa] yield, and 1900 °F [1040 °C] minimum solution anneal (Table 2 default) with rapid cooling heat treatment, while filler selection is by agreement because S21900 is not listed in Table 6. Put the manufacturing type, size and wall basis, finish, and any supplementary tests on the purchase order, and review the EN 10204 3.1 certificate against Tables 1, 2, and 4 before release. SHH STEEL can supply ASTM A312 TPXM-10 pipe to the edition you name; compare sister grades on the A312/A312M hub, or send your size list to admin@steelspecs.com.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X