ASTM A269 TP316 Stainless Steel Tube
What is ASTM A269 TP316 Stainless Steel Tube
ASTM A269 / A269M is the product specification for nominal-wall seamless and welded austenitic stainless steel tubing used in general corrosion-resisting and low- or high-temperature service. Grade TP316 is the molybdenum-bearing workhorse in that Table 1 list, recorded as UNS S31600, with carbon ≤0.08%, chromium 16.0–18.0%, nickel 10.0–14.0%, and molybdenum 2.00–3.00%. Buyers reach for A269 TP316 when instrumentation, hydraulic, or process tubing needs better chloride pitting resistance than TP304 without stepping all the way to a 6Mo super-austenitic. Writing “316 tube” on a bill of materials is not enough — the purchase order must name ASTM A269 so nominal-wall tolerances, solution treatment, hardness, flaring or flange tests, and marking apply to tubing rather than to an A213 boiler-tube or A312 pipe text.
SHH STEEL can produce and supply ASTM A269 TP316 stainless steel tube as seamless and welded product across the instrument-to-process OD × nominal-wall band, solution annealed and quenched, with EN 10204 3.1 mill test certificates that report Table 1 ladle chemistry and Table 2 hardness. Typical enquiry sizes run from about 6 mm to 168 mm outside diameter with 0.5–8.0 mm nominal wall; other diameters and walls are available by agreement. Start comparisons from the A269/A269M hub.
Commercial nicknames still say 316, 16-10-2, or S31600 general-service tube; none replace the ASTM grade on the MTC. Sister A269 pages include A269 TP316L, A269 TP316LN, A269 TP304, and higher-Mo A269 TP317. For boiler/HX or pipe forms of the same UNS idea, open or A312 TP316. A269’s wall basis is nominal wall — say that on the enquiry so nobody builds a minimum-wall A213 product by habit.
If the duty is actually boiler / heat-exchanger minimum-wall tube or pipe rather than A269 nominal-wall tubing, open A213 TP316, SA213 TP316, A312 TP316 and SA312 TP316 and match the product standard to the drawing.
Chemical Composition of A269 TP316
Every TP316 heat under A269 must meet Table 1 melting analysis. Product analysis on finished tube applies when the purchase order invokes it through ASTM A1016/A1016M, with tolerances typically from ASTM A480/A480M Table A1.1. SHH STEEL reports actual ladle values — and product values when ordered — and does not sell unpublished tighter catalogue windows as ASTM limits.
The table below reproduces Table 1 heat analysis for TP316 / UNS S31600 from public A269 excerpts (ASTM abstract cross-checked with the tubingchina A269 PDF). Values are maximum unless a range is shown. Confirm the purchased A269/A269M edition before treating any secondary catalogue as the acceptance text.
Melting analysis (heat / ladle analysis) — Table 1
| Element | TP316 (UNS S31600) melting analysis |
|---|---|
| Carbon (C) | ≤ 0.08 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 16.0 – 18.0 |
| Nickel (Ni) | 10.0 – 14.0 |
| Molybdenum (Mo) | 2.00 – 3.00 |
| Nitrogen (N) | … (no requirement) |
Source: ASTM A269/A269M Table 1 for TP316 / UNS S31600 (public excerpts). Molybdenum at 2.00–3.00% is the deliberate step up from TP304 for chloride-bearing and many chemical services. Nickel’s 10–14% band supports the Mo-bearing austenite; carbon ≤0.08% is the non-L ceiling, so as-welded sensitization risk sits above TP316L. Wikipedia’s 316-family context informs applications only — acceptance numbers come from Table 1, not from encyclopaedia text.
Mechanical Properties of A269 TP316
A269 does not publish a tensile-strength, yield, or elongation acceptance table for TP316. Finished-tube acceptance is built on hardness (Table 2), flaring (seamless), flange and reverse flattening (welded), and hydro or NDE on each length. Quoting a 75/30 ksi tensile floor as an A269 TP316 requirement without a purchase-order supplement would invent a number from a sister product standard.
| Property | TP316 requirement (A269 Table 2) |
|---|---|
| Hardness, max | 192 HBW / 200 HV or 90 HRB |
| Tensile / yield / elongation | Not specified as an A269 acceptance table for this grade |
Source: ASTM A269/A269M Table 2 for TP316 / UNS S31600 (public PDF excerpt). Hardness testing is waived on very small-ID or thin-wall tubes under the hardness-clause exemptions, but heat treatment still applies. Confirm superficial Rockwell alternatives in the purchased edition.
Seamless and Welded Tube
A269 allows TP316 tubing to be seamless or welded, hot-finished or cold-finished, unless the order locks the route. Welded A269 TP316 is produced without filler metal; the longitudinal seam is autogenous, then cold-worked and solution-treated with the tube. That differs from A312 pipe, where WLD and HCW codes carry their own stencil identity — A269 simply states seamless or welded.
Seamless TP316 takes a lot-basis flaring test; welded TP316 takes flange and reverse-flattening tests. Both share Table 2 hardness and the mandatory hydro or NDE test per length. Cold-finished tube dominates instrumentation and bright process lines; hot-finished seamless is more common on heavier walls. SHH STEEL can produce and supply both seamless and welded A269 TP316 — name the required route on the enquiry.
Dimensions and Tolerances
Order A269 TP316 by outside diameter and nominal wall thickness. Permissible variations come from A269 Table 4 and ASTM A1016/A1016M. Thin-wall ovality rules in clause 12.2 apply when wall falls below the thin-wall thresholds for each OD group.
| OD group (A269 Table 4) | Outside diameter tolerance | Wall thickness tolerance |
|---|---|---|
| Up to ½ in. [13 mm] | ±0.005 in. [0.13 mm] | ±15% |
| ½ to 1½ in. [13–38 mm], excl. | ±0.005 in. [0.13 mm] | ±10% |
| 1½ to 3½ in. [38–89 mm], excl. | ±0.010 in. [0.25 mm] | ±10% |
| 3½ to 5½ in. [89–140 mm], excl. | ±0.015 in. [0.38 mm] | ±10% |
| 5½ to 8 in. [140–203 mm], excl. | ±0.030 in. [0.76 mm] | ±10% |
Source: ASTM A269/A269M Table 4 (public PDF excerpt). Heavy-wall or low ID/OD tubes may take the footnote ±12.5% wall variation; sub-½ in. ID non-mandrel tube may take ±15%. Peer catalogues (Sandvik, Tubacex-style stainless tube ranges) were used only to sanity-check typical OD × wall enquiry bands — acceptance remains Table 4.
Equivalent Grades
TP316 / UNS S31600 is the ASTM tubing designation for standard Mo-bearing 16-10-2 austenitic. The same UNS idea appears as A213 TP316, A312 TP316, and A240 Type 316, but product form and mechanical acceptance are not interchangeable. EN 1.4401 / X5CrNiMo17-12-2 is a common commercial cousin after a chemistry check.
| Reference | Designation | Note |
|---|---|---|
| ASTM A269 | TP316 / UNS S31600 | This product standard |
| UNS | S31600 | Chemistry identity |
| ASTM A213 | TP316 | Seamless boiler / HX tube |
| ASTM A312 | TP316 | Pipe |
| EN (approx.) | 1.4401 / X5CrNiMo17-12-2 | Commercial cousin |
Inside A269, move to A269 TP316L for low carbon, or to A269 TP317 when 3–4% Mo is specified.
Same-grade pages under related product standards (different wall basis and mechanical tables — not drop-in substitutes for A269 tubing): A213 TP316, SA213 TP316, A312 TP316 and SA312 TP316. Confirm the product form before treating any of those pages as acceptance text for an A269 order.
Heat Treatment and Delivery Condition
All A269 TP316 tube is furnished solution heat-treated. Table 2 requires a minimum austenitizing temperature of 1900 °F [1040 °C], followed by water quench or other rapid cooling. Seamless tube may be individually quenched after hot forming while still at or above that temperature. Ordered final anneals below 1900 °F must be stenciled with the actual temperature after “HT.”
| Item | TP316 (A269 Table 2) |
|---|---|
| Austenitizing temperature, min | 1900 °F [1040 °C] |
| Cooling | Water quench or rapid cool |
| Hardness after heat treatment, max | 192 HBW / 200 HV or 90 HRB |
| Delivery condition | Solution heat-treated; pickled or bright-annealed by agreement |
Source: ASTM A269/A269M §6 and Table 2 for TP316. SHH STEEL ships only heat-treated condition that meets the ordered Table 2 requirement, and the MTC states what was done.
Corrosion Resistance
Molybdenum at 2–3% is why TP316 outruns TP304 in chloride pitting and crevice regimes that matter on process and marine-adjacent utilities. Chromium still builds the passive film; molybdenum helps where localised attack defeats plain 18-8. Carbon up to 0.08% means HAZ sensitization remains possible if welded fabrications see corrosive service without a post-weld anneal — prefer TP316L for as-welded corrosive duty.
A269 publishes no PREN or CPT table for S31600 — do not invent one. Many chemical and chloride-bearing utilities suit TP316; seawater splash zones and aggressive chlorides often need A269 UNS S31254 or another 6Mo grade under the same standard.
Applications of A269 TP316 Tube
A269 TP316 shows up on chloride-aware instrument and impulse lines, chemical process transfer tubing, food plants with chloride washdown, marine-adjacent utilities that do not yet need 6Mo, and heat-transfer coils specified to A269 rather than A213. Bright-annealed cold-finished tube dominates skid and panel work; pickled welded tube covers larger utility runs.
Skip it for Code boiler / superheater tube (use A213), for pipe headers (use A312), and for seawater or strong reducing acids that need 6Mo or nickel alloys. SHH STEEL can produce and supply A269 TP316 across that general-service band and will say when TP316L or a higher alloy is safer.
When a sister enquiry is for boiler tube or pipe of the same grade, use A213 TP316, SA213 TP316, A312 TP316 and SA312 TP316 instead of stretching an A269 tubing page into the wrong product form.
Weldability
TP316 welds readily by GTAW and GMAW with 316/316L-type fillers when filler is used on fabrication joints. Autogenous A269 welded tube already carries a mill seam that was cold-worked and solution-treated with the tube; shop welds on cut lengths sit outside that mill anneal. Standard carbon keeps as-welded HAZ sensitization as a design input in corrosive service without re-annealing.
Projects that must stay as-welded usually specify A269 TP316L from the start. Filler selection and purge remain the fabricator’s scope; SHH STEEL’s A269 scope is the mill tube, chemistry, hardness, and process route on the purchase order.
Surface Finishes
Pickled and bright-annealed are the two standard A269 TP316 deliveries. Bright anneal suits instrumentation and hygienic lines; pickle is the general-process default. Named OD polish grit is a supplementary finish when the purchase order requires it — A269 does not mandate a polish grade.
Interior Ra limits or scrubbed-ID notes belong in the enquiry. SHH STEEL can produce and supply pickled, bright-annealed, and polished A269 TP316 when the mill can measure and report the finish.
Inspection and Testing
Lot testing for A269 TP316 covers Table 2 hardness, flaring on seamless tube, and flange plus reverse flattening on welded tube. Each length also takes a hydrostatic test or a nondestructive electric test; the manufacturer chooses unless the purchase order locks the method. NDE-tested lengths are marked “NDE” and certified accordingly.
SHH STEEL EN 10204 3.1 certificates report ladle chemistry (including Mo), heat-treatment condition, hardness, and the hydro/NDE statement. PMI and third-party inspection are available when named on the order.
Packaging and Shipping
TP316 tube ships with end caps, size-sorted bundles or crates, and waterproof wrap for ocean freight. Bright-annealed and polished OD get sleeve protection against transit galling. Coiled tubing, when ordered, follows A269’s continuous-coil rule without circumferential butt welds inside the coil.
Marking typically includes ASTM A269, TP316 / S31600, size, heat number, seamless or welded identity, and NDE when that route was used. SHH STEEL aligns stencil and tags with the purchase-order marking clause before dispatch.
Why Choose SHH STEEL
SHH STEEL can produce and supply ASTM A269 TP316 as nominal-wall seamless or welded tubing — solution annealed to Table 2, hardness-tested, hydro- or NDE-tested, and documented on EN 10204 3.1 certificates — not as a generic “316 tube” label. We keep A269 distinct from A213 and A312 on the MTC, we state seamless versus welded honestly, and we will not paste A213 tensile floors onto an A269 shipment.
If as-welded corrosive service needs low carbon, we point to A269 TP316L; if chlorides outgrow 2–3% Mo, we point to TP317 or a 6Mo A269 grade rather than stretching TP316 past its envelope.
Supply Capability
SHH STEEL can produce and supply ASTM A269 TP316 stainless steel tube against the edition, process route, and finish named on your enquiry. Capability and Stock / Available sizes follow.
| Item | SHH STEEL capability for TP316 |
|---|---|
| Standard | ASTM A269 / A269M |
| Grade | TP316 / UNS S31600 |
| Product form | Seamless and welded tube (no filler metal for welded), hot- or cold-finished |
| Delivery condition | Solution heat-treated ≥1900 °F [1040 °C]; pickled or bright-annealed |
| Typical size band | ~6–168 mm OD × 0.5–8.0 mm nominal wall (others by agreement) |
| Testing | Hardness; flaring (seamless) / flange + reverse flattening (welded); hydro or NDE |
| Documents | EN 10204 3.1 MTC; third-party inspection on request |
Stock / Available sizes
Enquiry-oriented supply range for A269 TP316 — not a frozen warehouse SKU list with tonnages. Send the OD × nominal-wall list and seamless/welded preference for confirmation against near-term production.
| OD (mm) | Typical nominal walls (mm) | Notes |
|---|---|---|
| 6 / 8 / 10 / 12 / 14 | 0.5 / 0.8 / 1.0 / 1.2 / 1.5 | Instrument / hydraulic; often BA |
| 12.7 / 15.9 / 19.1 / 25.4 / 31.8 | 1.0 / 1.2 / 1.5 / 2.0 / 2.5 | Inch OD process and utility |
| 38.1 / 48.3 / 60.3 / 76.1 | 1.5 / 2.0 / 2.5 / 3.0 / 4.0 | Utility and light process; Mo preferred over 304 |
| 88.9 / 114.3 / 141.3 / 168.3 | 2.0 / 3.0 / 4.0 / 6.0 / 8.0 | Larger process tube; lock seamless vs welded |
Parallel quotes against A269 TP316L and A269 TP304 on the same size list keep Mo cost visible.
FAQ
-
What is ASTM A269 TP316 stainless steel tube used for?
- A269 TP316 is the molybdenum-bearing nominal-wall tubing grade for chloride-aware instrumentation, chemical process transfer, marine-adjacent utilities, and food plants with chloride washdown. It covers seamless and welded general-service tube under ASTM A269 — not Code boiler tube (that is A213) and not pipe (that is A312). Naming A269 on the purchase order locks wall basis, hardness, and flaring or flange tests to the tubing product standard.
-
TP304 vs TP316 under A269 — which should I buy?
- Buy TP304 for milder aqueous and food-contact duties where molybdenum is not justified. Buy TP316 when chloride pitting or many chemical media need the 2.00–3.00% Mo addition in Table 1. They share an austenitic family but are separate A269 grades with different chemistry lines; do not treat “304/316 tube” as one interchangeable stamp on the MTC.
-
Does ASTM A269 TP316 include welded tube?
- Yes. A269 covers both seamless and welded TP316. Welded tube is made without filler metal, cold-worked, and solution-treated with the tube, then flange- and reverse-flattening-tested on the seam. Site titles omit the word “Welded” by house style, but the purchase order and MTC still state seamless or welded. SHH STEEL can produce and supply both routes.
-
What hardness does A269 require for TP316?
- Table 2 sets a maximum of 192 HBW / 200 HV or 90 HRB after solution treatment at ≥1900 °F [1040 °C]. A269 does not publish a tensile, yield, or elongation acceptance table for TP316, so do not invent 75/30 ksi-style floors from A213 unless the purchase order adds them as extras for the project.
-
TP316 vs TP316L for A269 tubing — which should I order?
- Order TP316 when standard carbon (≤0.08%) is acceptable and fabrication will be re-annealed or service is mild. Order TP316L when as-welded intergranular corrosion resistance matters and carbon must stay at the L-grade ceiling. They are separate A269 grades and must not share one heat stamp on the same MTC line.
-
Is A269 TP316 a nominal-wall or minimum-wall standard?
- A269 is written on a nominal-wall-thickness basis for general-service tubing. State OD × nominal wall on the enquiry unless you agree a different wall basis with the mill in writing. Table 4 then governs outside-diameter, wall, and cut-length tolerances. Do not assume A213 minimum-wall boiler-tube practice applies to an A269 TP316 order.
-
What size range can SHH STEEL supply for A269 TP316?
- SHH STEEL can produce and supply A269 TP316 in a typical band of about 6–168 mm OD with 0.5–8.0 mm nominal wall, seamless or welded, pickled or bright-annealed, with EN 10204 3.1 mill test certificates. Larger or heavier sizes are quoted by agreement against mill capability — send the OD × wall list for a firm near-term availability answer.
-
When should I choose TP317 or 6Mo instead of TP316?
- Step to TP317 when the material list wants 3–4% molybdenum, or to a 6Mo A269 grade such as UNS S31254 when seawater, strong chlorides, or aggressive chemical media outgrow the 2–3% Mo band. TP316 remains the workhorse for many chloride-aware but not seawater-splash duties under A269 general-service tubing.
-
Hydrostatic or NDE testing for A269 TP316?
- Each tube must receive either a hydrostatic test or a nondestructive electric test; the manufacturer chooses unless the purchase order locks one method. NDE-tested lengths are marked “NDE” and the certificate states that choice. Hardness and flaring or flange tests remain separate lot requirements beside the hydro/NDE decision.
-
What documents come with SHH STEEL A269 TP316?
- EN 10204 3.1 mill test certificates report ladle chemistry against Table 1 including molybdenum, solution-treatment condition, hardness against Table 2, and the hydrostatic or NDE statement. Third-party inspection and PMI can be added on the order. Stencil carries ASTM A269, TP316 / S31600, size, heat, and seamless or welded identity.
-
How do I enquire for A269 TP316 with SHH STEEL?
- Send ASTM A269, grade TP316 / UNS S31600, seamless or welded preference, OD × nominal-wall list and lengths or coil, finish, and any hydro/NDE lock. Add a short note on the service medium if selection between TP316, TP316L, and higher-Mo A269 grades is still open. SHH STEEL can produce and supply to that enquiry.
Conclusion
ASTM A269 TP316 / UNS S31600 is the molybdenum-bearing workhorse inside the A269 nominal-wall tubing family when chloride-aware general service needs 2–3% Mo and standard carbon is acceptable. SHH STEEL can produce and supply seamless and welded A269 TP316 tube, solution annealed to Table 2, tested, and documented on EN 10204 3.1 certificates. Start from the A269/A269M hub, then send your OD × nominal-wall list and process route. Contact admin@steelspecs.com with the size list and medium notes for a production-backed offer.