ASTM A269 TP321 Stainless Steel Tube
What is ASTM A269 TP321 Stainless Steel Tube
ASTM A269 / A269M covers nominal-wall seamless and welded austenitic stainless steel tubing for general corrosion-resisting and low- or high-temperature service. Grade TP321 is the titanium-stabilized 18-8-family austenitic under UNS S32100, with carbon ≤0.08%, chromium 17.0–19.0%, nickel 9.0–12.0%, and titanium meeting the Footnote D formula (≥5 × (C + N), ≤0.70% — confirm the exact footnote in the purchased edition). Buyers specify A269 TP321 when they want stabilization against sensitization for welded or intermittently heated general-service tubing without switching to niobium-stabilized TP347. The shop name “321 tube” still needs ASTM A269 on the purchase order so nominal-wall rules, hardness, flaring or flange tests, and marking apply to tubing — not to an A213 boiler-tube or A312 pipe text.
SHH STEEL can produce and supply ASTM A269 TP321 stainless steel tube as seamless and welded product in the instrument-to-process OD × nominal-wall band, solution annealed, with EN 10204 3.1 certificates reporting Table 1 chemistry (including titanium) and Table 2 hardness. Typical sizes run about 6–168 mm OD × 0.5–8.0 mm nominal wall; other sizes by agreement. Compare sisters on the A269/A269M hub with A269 TP347, A269 TP304L, and A269 TP316L. Keep the wall basis nominal. Note that A269 §6.3 warns that solution annealing above 1950 °F [1065 °C] may impair intergranular corrosion resistance after subsequent sensitizing exposure in TP321, TP347, and TP348 — stabilization or re-solution options may be ordered under supplementary wording.
If the duty is actually boiler / heat-exchanger minimum-wall tube or pipe rather than A269 nominal-wall tubing, open A213 TP321, SA213 TP321, A312 TP321 and SA312 TP321 and match the product standard to the drawing.
Chemical Composition of A269 TP321
Table 1 melting analysis is mandatory for every TP321 heat. Product analysis applies when ordered through A1016/A1016M and A480 Table A1.1. SHH STEEL reports measured ladle (and product, when ordered) values, including titanium against the stabilization formula — never unpublished tighter catalogue windows.
Public A269 Table 1 excerpts for TP321 / UNS S32100 are reproduced below (ASTM abstract + tubingchina A269 PDF). The titanium formula is cross-checked against the A213 sister-text wording commonly used for S32100 (Ti ≥5 × (C + N), ≤0.70%); confirm Footnote D exactly in the purchased A269 edition because public block-1 footnote letters can be hard to read in excerpt copies.
Melting analysis (heat / ladle analysis) — Table 1
| Element | TP321 (UNS S32100) melting analysis |
|---|---|
| Carbon (C) | ≤ 0.08 |
| Manganese (Mn) | ≤ 2.00 |
| Phosphorus (P) | ≤ 0.045 |
| Sulfur (S) | ≤ 0.030 |
| Silicon (Si) | ≤ 1.00 |
| Chromium (Cr) | 17.0 – 19.0 |
| Nickel (Ni) | 9.0 – 12.0 |
| Titanium (Ti) | ≥ 5 × (C + N), ≤ 0.70 (Footnote D — confirm edition) |
| Molybdenum (Mo) | … (no requirement) |
Source: ASTM A269/A269M Table 1 for TP321 / UNS S32100 (public excerpts); Ti formula cross-checked with A213 S32100 sister text. Nitrogen may need to be analysed for the Ti formula even when N has no standalone Table 1 range — method by agreement where the standard’s nitrogen footnote applies. No molybdenum — chloride-heavy duty still belongs on Mo-bearing A269 grades.
Mechanical Properties of A269 TP321
A269 does not publish a tensile acceptance table for TP321. Lot acceptance uses Table 2 hardness, flaring for seamless tube, flange and reverse flattening for welded tube, and hydro or NDE on each length. Do not invent tensile floors from A213 or A312 unless the purchase order adds them as project extras.
| Property | TP321 requirement (A269 Table 2) |
|---|---|
| Hardness, max | 192 HBW / 200 HV or 90 HRB |
| Tensile / yield / elongation | Not specified as an A269 acceptance table for this grade |
Source: ASTM A269/A269M Table 2 for TP321 / UNS S32100 (public PDF excerpt). Confirm thin-wall superficial Rockwell alternatives in the purchased edition’s hardness clause before writing them into a quality plan.
Seamless and Welded Tube
TP321 under A269 may be seamless or welded, hot-finished or cold-finished. Welded A269 tube is autogenous — no filler metal in the longitudinal seam — then cold-worked and solution-treated with the tube. That is not A312 WLD/HCW pipe stencil language; A269 simply records seamless or welded as the process route.
Seamless TP321 is flare-tested on a lot basis; welded TP321 takes flange and reverse-flattening tests so the seam is exercised in both modes. Both share Table 2 hardness and the mandatory hydro or NDE test per length. Titanium stabilization is why fabricators pick 321 for welded general-service lines that see intermittent heating — still, the mill anneal covers the as-shipped tube, not later shop welds. SHH STEEL can produce and supply both seamless and welded A269 TP321 against the same Table 1 and Table 2 floors.
Dimensions and Tolerances
Order A269 TP321 by outside diameter and nominal wall thickness, not by pipe schedule as the primary size language. Permissible variations come from A269 Table 4 and ASTM A1016/A1016M, while thin-wall ovality rules in clause 12.2 apply when wall falls below the thin-wall thresholds for each OD group.
| OD group (A269 Table 4) | Outside diameter tolerance | Wall thickness tolerance |
|---|---|---|
| Up to ½ in. [13 mm] | ±0.005 in. [0.13 mm] | ±15% |
| ½ to 1½ in. [13–38 mm], excl. | ±0.005 in. [0.13 mm] | ±10% |
| 1½ to 3½ in. [38–89 mm], excl. | ±0.010 in. [0.25 mm] | ±10% |
| 3½ to 5½ in. [89–140 mm], excl. | ±0.015 in. [0.38 mm] | ±10% |
| 5½ to 8 in. [140–203 mm], excl. | ±0.030 in. [0.76 mm] | ±10% |
Source: ASTM A269/A269M Table 4 (public PDF excerpt). Footnotes allow wider wall variation on heavy wall or low ID/OD ratios and on sub-½ in. ID non-mandrel tube. If a drawing uses A213 minimum-wall language, say so on the enquiry so SHH STEEL does not build the wrong wall basis.
Equivalent Grades
TP321 / UNS S32100 is the ASTM tubing grade for titanium-stabilized 18-8-family austenitic. Cousins include A213 TP321, A312 TP321, A240 Type 321, and EN 1.4541 / X6CrNiTi18-10 — confirm chemistry and product form before substituting across those product standards.
| Reference | Designation | Note |
|---|---|---|
| ASTM A269 | TP321 / UNS S32100 | This product standard |
| UNS | S32100 | Chemistry identity |
| ASTM A213 | TP321 | Seamless boiler / HX tube |
| ASTM A312 | TP321 | Pipe |
| EN (approx.) | 1.4541 / X6CrNiTi18-10 | Commercial cousin |
Inside A269, choose A269 TP347 when niobium stabilization is preferred, or A269 TP304L when low carbon without stabilizer is enough for the duty.
Same-grade pages under related product standards (different wall basis and mechanical tables — not drop-in substitutes for A269 tubing): A213 TP321, SA213 TP321, A312 TP321 and SA312 TP321. Confirm the product form before treating any of those pages as acceptance text for an A269 order.
Heat Treatment and Delivery Condition
All A269 TP321 ships solution heat-treated. Table 2 requires ≥1900 °F [1040 °C] austenitizing with water quench or rapid cool. A269 §6.3 notes that solution annealing above 1950 °F [1065 °C] may impair resistance to intergranular corrosion after subsequent sensitizing exposure in TP321 (and TP347 / TP348); when specified, a lower-temperature stabilization or re-solution anneal may follow the initial high-temperature solution anneal (see Supplementary Requirement S3 in the ordered edition).
| Item | TP321 (A269 Table 2 / §6) |
|---|---|
| Austenitizing temperature, min | 1900 °F [1040 °C] |
| Note on high anneal | Above 1950 °F [1065 °C] may impair IGC resistance after sensitizing — confirm §6.3 |
| Hardness after heat treatment, max | 192 HBW / 200 HV or 90 HRB |
| Delivery condition | Solution heat-treated; pickled or bright-annealed by agreement |
Source: ASTM A269/A269M §6 and Table 2 for TP321 (public PDF excerpt). SHH STEEL’s MTC states the heat-treatment condition applied; order stabilization language explicitly if the project requires Supplementary S3 treatment.
Corrosion Resistance
Titanium stabilization ties up carbon as titanium carbide/carbonitride so chromium stays available for the passive film in heat-affected zones — that is the corrosion reason to buy TP321 instead of standard TP304 for welded or intermittently heated general-service tubing. It still lacks molybdenum, so chloride pitting performance stays below TP316L and 6Mo grades under the same A269 product standard.
A269 publishes no PREN for S32100 — do not invent one from marketing sheets. Use TP321 for stabilization-driven general service; use A269 TP316L when Mo is required; use A269 TP347 when Nb stabilization is preferred over Ti.
Applications of A269 TP321 Tube
A269 TP321 appears on welded general-service instrument and process lines that see intermittent heating, heat-recovery related tubing specified to A269 rather than A213, and projects that standardized on titanium-stabilized chemistry across product forms. Bright-annealed cold-finished tube is common on skids; pickled welded tube covers larger utility runs.
For Code boiler or superheater tube open A213 TP321; for pipe open A312 TP321. SHH STEEL can produce and supply A269 TP321 in the general-service band above and will redirect when molybdenum or niobium stabilization is the better metallurgical fit for the stated medium.
When a sister enquiry is for boiler tube or pipe of the same grade, use A213 TP321, SA213 TP321, A312 TP321 and SA312 TP321 instead of stretching an A269 tubing page into the wrong product form.
Weldability
Titanium stabilization is the welding reason to choose TP321 over TP304 for as-welded or intermittently heated fabrications. GTAW and GMAW with 321- or 347-type fillers — when filler is used on fabrication joints — are common practice; mill autogenous A269 welds are already cold-worked and solution-treated with the tube body before shipment.
Shop welds on cut lengths sit outside that mill anneal and need proper purge and procedure. Mind the §6.3 high-anneal note when specifying heat treatment after fabrication. SHH STEEL supplies the mill product and MTC with titanium reported against the stabilization formula.
Surface Finishes
Pickled and bright-annealed finishes cover most A269 TP321 orders, and named OD polish grit is quoted as a supplementary finish when the purchase order requires a measured belt polish. Bright anneal suits instrumentation and clean-process ID/OD; pickle is the general-process default when a clean but not bright surface is enough.
Write any maximum Ra or scrubbed-ID note into the enquiry. SHH STEEL can produce and supply pickled, bright-annealed, and polished A269 TP321 when the mill can measure and report the finish, and we will not claim an unverified polish grade on the certificate.
Inspection and Testing
Lot testing for A269 TP321 covers Table 2 hardness, flaring on seamless tube, and flange plus reverse flattening on welded tube, with lot definitions tied to heat, size, and heat-treatment charge as written in the standard. Each length must also receive a hydrostatic test or a nondestructive electric test; the manufacturer chooses unless the purchase order locks the method.
EN 10204 3.1 certificates from SHH STEEL report ladle chemistry including titanium, solution-treatment condition, hardness against Table 2, and the hydro or NDE statement. PMI and third-party inspection holds are available when named on the order, and we do not skip mandatory tests to shorten lead time.
Packaging and Shipping
Export and domestic packs for A269 TP321 use end caps, size-sorted bundles or crates, and waterproof wrap for ocean freight so OD finish and ends stay protected in transit. Bright-annealed and polished OD get extra sleeve protection against galling; coiled product, when ordered, follows A269’s continuous-coil rule without circumferential butt welds inside the coil.
Stencil and tags typically carry ASTM A269, TP321 / S32100, size, heat number, seamless or welded identity, and NDE when that route was used. SHH STEEL matches marking to the purchase-order marking clause before dispatch so receiving inspection can verify identity against the MTC.
Why Choose SHH STEEL
SHH STEEL can produce and supply ASTM A269 TP321 as solution-treated seamless or welded tubing with Table 1 chemistry — including titanium against the stabilization formula — Table 2 hardness, and EN 10204 3.1 documentation. We will not ship TP304 and call it 321, and we will not omit titanium from the certificate when the grade requires it.
If niobium stabilization or molybdenum is what the duty needs, we point to A269 TP347 or A269 TP316L rather than selling the wrong stabilizer or alloy family into the job.
Supply Capability
SHH STEEL can produce and supply ASTM A269 TP321 stainless steel tube against the edition, process route, and finish named on your enquiry. The capability table and Stock / Available sizes enquiry map below frame a first-pass size list — not a frozen warehouse SKU list with tonnages.
| Item | SHH STEEL capability for TP321 |
|---|---|
| Standard | ASTM A269 / A269M |
| Grade | TP321 / UNS S32100 |
| Product form | Seamless and welded tube (no filler metal for welded), hot- or cold-finished |
| Delivery condition | Solution heat-treated ≥1900 °F [1040 °C]; pickled or bright-annealed; stabilization when ordered |
| Typical size band | ~6–168 mm OD × 0.5–8.0 mm nominal wall (others by agreement) |
| Testing | Hardness; flaring (seamless) / flange + reverse flattening (welded); hydro or NDE |
| Documents | EN 10204 3.1 MTC; third-party inspection on request |
Stock / Available sizes
Send the OD × nominal-wall list and seamless/welded preference for confirmation against near-term production or partner stock. Peer stainless-tube catalogues were used only to sanity-check typical OD × wall enquiry bands.
| OD (mm) | Typical nominal walls (mm) | Notes |
|---|---|---|
| 6 / 8 / 10 / 12 / 14 | 0.5 / 0.8 / 1.0 / 1.2 / 1.5 | Instrument band; often BA |
| 12.7 / 19.1 / 25.4 / 31.8 | 1.0 / 1.5 / 2.0 / 2.5 | Inch OD process / heat-related utility |
| 38.1 / 48.3 / 60.3 / 76.1 | 1.5 / 2.0 / 3.0 / 4.0 | Stabilized general-service tube |
| 88.9 / 114.3 / 141.3 / 168.3 | 2.0 / 3.0 / 4.0 / 6.0 / 8.0 | Larger process tube; lock seamless vs welded |
Parallel quotes against A269 TP347 and A269 TP304L keep stabilizer versus L-grade choices visible on one size list.
FAQ
-
What is ASTM A269 TP321 stainless steel tube used for?
- A269 TP321 is titanium-stabilized nominal-wall tubing for welded or intermittently heated general-service lines where sensitization resistance matters more than molybdenum. It covers seamless and welded tubing under ASTM A269 — not Code boiler tube (that is A213) and not pipe (that is A312). Naming A269 on the purchase order locks the nominal-wall basis, hardness, and flaring or flange tests to the tubing product standard.
-
TP321 vs TP304L under A269 — which should I buy?
- Buy TP304L when low carbon without a stabilizer is enough for as-welded corrosive or hygienic duty. Buy TP321 when titanium stabilization is specified for welded or intermittently heated general service. They solve sensitization differently — L-grade carbon versus titanium carbide/carbonitride formation — and must not share one grade stamp on the same MTC line.
-
TP321 vs TP347 under A269 — titanium or niobium?
- Both are stabilized austenitics under A269. TP321 uses titanium against the Footnote D formula; TP347 uses niobium (columbium) with a 10×C minimum and 1.10% maximum. Choice is usually driven by the material list, preferred filler practice, and project preference. Compare both on the same OD × wall list with SHH STEEL when the stabilizer decision is still open.
-
Does ASTM A269 TP321 include welded tube?
- Yes. Seamless and welded routes are both allowed under A269. Welded tube is made without filler metal, cold-worked, and solution-treated with the tube, then flange- and reverse-flattening-tested on the seam. Site titles omit the word “Welded” by house style, but the purchase order and MTC still state seamless or welded. SHH STEEL can produce and supply both routes.
-
What hardness limit applies to A269 TP321?
- Table 2 caps TP321 at 192 HBW / 200 HV or 90 HRB after solution treatment at ≥1900 °F [1040 °C]. A269 does not publish a tensile, yield, or elongation acceptance table for this grade, so do not invent 75/30 ksi-style floors from A213 unless the purchase order adds them as extras for the project.
-
Why does A269 warn about annealing TP321 above 1950 °F?
- Section 6.3 notes that solution annealing above 1950 °F [1065 °C] may impair intergranular corrosion resistance after subsequent sensitizing exposure in TP321, TP347, and TP348. When needed, a lower-temperature stabilization or re-solution anneal can be ordered after the initial high-temperature solution anneal — confirm Supplementary Requirement S3 wording in the purchased A269 edition before writing it into the PO.
-
Is A269 TP321 a nominal-wall or minimum-wall standard?
- A269 is written on a nominal-wall-thickness basis for general-service tubing. Write OD × nominal wall on the enquiry unless you and the mill agree a different wall basis in writing. Table 4 then governs outside-diameter, wall, and cut-length tolerances. Do not assume A213 minimum-wall boiler-tube practice applies to an A269 TP321 order.
-
What size range can SHH STEEL produce for A269 TP321?
- SHH STEEL can produce and supply about 6–168 mm OD with 0.5–8.0 mm nominal wall in seamless or welded A269 TP321, pickled or bright-annealed, with EN 10204 3.1 mill test certificates. Larger or heavier sizes are quoted by agreement against mill capability — send the OD × wall list and process preference for a firm near-term availability answer.
-
Must titanium appear on the MTC for TP321?
- Yes. Titanium is the defining Table 1 requirement through the stabilization formula, so the ladle analysis on an EN 10204 3.1 certificate should report Ti (and carbon, and nitrogen when needed for the formula). A certificate that only shows a “321” nickname without titanium values is incomplete for grade acceptance under A269.
-
What certificate does SHH STEEL provide for A269 TP321?
- EN 10204 3.1 mill test certificates report ladle chemistry including titanium, solution-treatment condition, hardness against Table 2, and the hydrostatic or NDE statement. Third-party inspection and PMI can be added when named on the order. Stencil shows ASTM A269, TP321 / S32100, size, heat, and seamless or welded identity.
-
How should I enquire for A269 TP321 with SHH STEEL?
- List ASTM A269, grade TP321 / UNS S32100, seamless or welded preference, OD × nominal-wall list and lengths or coil, finish, any stabilization or Supplementary S3 language, and any hydro/NDE lock. SHH STEEL can produce and supply to that enquiry or recommend TP347 or TP304L when the material list points to niobium stabilization or low-carbon without stabilizer.
Conclusion
ASTM A269 TP321 / UNS S32100 is the titanium-stabilized austenitic inside the A269 nominal-wall tubing family when welded or intermittently heated general service needs stabilization without molybdenum. SHH STEEL can produce and supply seamless and welded A269 TP321, solution annealed to Table 2, tested, and documented on EN 10204 3.1 certificates. Start from the A269/A269M hub, then send the OD × nominal-wall list. Contact admin@steelspecs.com for a production-backed offer.