EN 10088-2 X1CrNiMoCuN24-22-8 1.4652 Stainless Steel Plate at SHH STEEL warehouse

EN 10088-2 X1CrNiMoCuN24-22-8 1.4652 Stainless Steel Plate

EN 10088-2 X1CrNiMoCuN24-22-8 1.4652 Stainless Steel Plate: super-austenitic grade to EN 10088-2, hot-rolled plate from stock in China. SHH STEEL supplies mill-direct material with EN 10204 3.1/3.2 certificates, third-party inspection and cutting to size.
Keywords
1.4652 stainless steel plate, 1.4652 plate, 1.4652 stainless plate supplier, EN 10088-2 1.4652, 1.4652 plate stock China
Equivalent Grades:
UNS S32654; GB/T 015Cr24Ni22Mo8Mn3CuN (S32652)
Share:
Overview
Specification
Chemical Composition
Mechanical Properties
Performance
Grade Selection
Heat Treatment
Surface Finishes
Tolerances
Stock
Equivalent Grades
Related Grades
Applications and Fabrication
Testing and Inspection
Specification Mistakes
Buyer Concerns
How to Order
FAQ
Conclusion

What is EN 10088-2 X1CrNiMoCuN24-22-8 1.4652 Stainless Steel Plate?

Technical reviewer: Jack · Updated: 2026-10-21

Equivalent grades: 1.4652 X1CrNiMoCuN24-22-8 ≈ UNS S32654 ≈ GB/T 015Cr24Ni22Mo8Mn3CuN (S32652).

1.4652 X1CrNiMoCuN24-22-8 is a super-austenitic grade. 1.4652 is a 7Mo super-austenitic steel with about 0.5 % N and PREN of about 56, among the most corrosion-resistant steels in EN 10088-2. It is used in hot, chlorinated seawater and aggressive chemical service where 6Mo grades reach their crevice-corrosion limit.

EN 10088-2 is the European standard for stainless steel sheet, plate and strip for general purposes. It defines the chemistry, the mechanical properties for each product form (C = cold-rolled strip, H = hot-rolled strip, P = hot-rolled plate) and the process routes that give each surface finish. Pressure-equipment plate is ordered to EN 10028-7 instead, which adds elevated-temperature properties.

This page sets out the EN 10088-2 requirements for 1.4652 X1CrNiMoCuN24-22-8 plate: specification summary, chemistry, mechanical properties, corrosion resistance, heat treatment, finishes and tolerances, current stock, equivalents, fabrication and testing. SHH STEEL supplies it mill-direct from China with EN 10204 3.1 certificates, optional third-party inspection and in-house cutting.

1.4652 X1CrNiMoCuN24-22-8 plate: specification summary

Item 1.4652 X1CrNiMoCuN24-22-8 data
Standard EN 10088-2:2014, stainless steels for general purposes – sheet/plate and strip
Product forms C = cold-rolled strip, H = hot-rolled strip, P = hot-rolled plate
Process routes / finishes 1C, 1E, 1D (hot rolled); 2D, 2B, 2R (cold rolled); special finishes by agreement
Typical thickness 0.5–6 mm cold rolled; 3–100 mm hot-rolled plate depending on grade
Dimensions and tolerances EN 10029 (plate), EN 10051 (hot-rolled strip and sheet), EN ISO 9445-1/-2 (cold rolled)
Required tests cast analysis, tensile test; corrosion test by agreement
Inspection documents EN 10204 3.1 or 3.2
Grade family super-austenitic

Size range. Plate is produced on Steckel or reversing mills from about 5 mm up to 80–100 mm depending on grade, with widths of 1500–2500 mm and lengths up to 12 m; thinner plate of 3–12 mm is often cut from hot-rolled coil. Very heavy or wide plates, and plates with tight flatness, should be confirmed before ordering. 1.4652 X1CrNiMoCuN24-22-8 is a specialty grade made by a limited number of mills in campaign rolling. Stock covers the common sizes listed below; for project quantities or unusual sizes, plan for a mill campaign and reserve the heat early.

Chemical composition of 1.4652 X1CrNiMoCuN24-22-8 (EN 10088-2)

Element wt %
C 0.020 max
Si 0.50 max
Mn 2.0–4.0
P 0.030 max
S 0.005 max
Cr 23.0–25.0
Ni 21.0–23.0
Mo 7.0–8.0
Cu 0.30–0.60
N 0.45–0.55

Single values are maximums unless marked min. Ranges are heat (cast) analysis limits.

PREN check (Cr + 3.3 Mo + 16 N): about 53.3 at the specification minimums and about 56.8 at mid-range. Where corrosion resistance is critical, write a minimum PREN on the order and ask for the calculated value from the heat analysis on the certificate.

Mechanical properties of 1.4652 X1CrNiMoCuN24-22-8 plate

Product form / thickness Rp0.2 min, MPa Rm, MPa A min, % (transverse)
P, hot-rolled plate ≤ 50 mm 430 750–1000 40

The minimum yield strength of 430 MPa is about 2.5 times the 170 MPa minimum of ASTM 316L. The nitrogen addition is responsible for most of the extra strength; it also increases forming loads compared with 316L. Tension tests are taken in the direction stated in the standard; where a hardness limit is given, it is a maximum that confirms correct annealing.

Corrosion resistance of 1.4652 X1CrNiMoCuN24-22-8: PREN and limits

Super-austenitic grades are bought for one reason: chloride resistance. The pitting resistance equivalent number (PREN = Cr + 3.3 Mo + 16 N) at the specification minimum is about 53.3, and a mid-range heat is about 56.8. In practice this means resistance to pitting and crevice attack in seawater and chloride process streams where 316L and 904L fail, and a critical pitting temperature (ASTM G48 Method C/E) that is usually well above 50 °C for good mill product.

Because the structure is fully austenitic, these steels are also immune to the 300 °C service limit that applies to duplex, they stay tough at cryogenic temperatures, and they do not need ferrite control. The trade-off is segregation: high molybdenum segregates during solidification and can form sigma and chi phases if plate is cooled slowly after solution annealing. Good practice is to specify an ASTM G48 or A262-type acceptance test on the actual heat and to ask for the solution-anneal temperature on the mill certificate.

How 1.4652 X1CrNiMoCuN24-22-8 compares with related grades

Grade Cr Ni Mo N PREN (min) YS / Rp0.2 min, MPa
1.4652 X1CrNiMoCuN24-22-8 23.0–25.0 21.0–23.0 7.0–8.0 0.45–0.55 53.3 430
UNS S31254 19.5–20.5 17.5–18.5 6.0–6.5 0.18–0.25 42.2 310
UNS N08367 20.0–22.0 23.5–25.5 6.0–7.0 0.18–0.25 42.7 310
UNS S34565 23.0–25.0 16.0–18.0 4.0–5.0 0.40–0.60 42.6 415
UNS S32654 24.0–25.0 21.0–23.0 7.0–8.0 0.45–0.55 54.3 430

Choose 1.4652 X1CrNiMoCuN24-22-8 for warm seawater, chloride process streams and acidic chloride service where a fully austenitic, tough and non-magnetic structure is preferred. It costs more than super duplex in most markets, so it is usually chosen where low-temperature toughness, formability or service above 300 °C rules duplex out.

The table uses specification limits, not typical mill values, so it shows the guaranteed position of each grade. Final selection should also consider product availability in the thickness you need, welding consumables, and the inspection requirements of your project.

Heat treatment and delivery condition of 1.4652 X1CrNiMoCuN24-22-8

Heat treatment: 1150–1200 °C, water or air (rapid).

A high solution-anneal temperature dissolves sigma and chi phases and evens out molybdenum segregation; water quenching is used for plate. Hot forming should finish above about 1000 °C and be followed by a solution anneal.

Surface finishes for 1.4652 X1CrNiMoCuN24-22-8 plate

EN 10088-2 identifies finishes by process route. 1D (hot rolled, heat treated, pickled) is the normal plate finish; 1E is mechanically descaled. Cold-rolled material is supplied as 2D (dull), 2B (skin passed) or 2R (bright annealed). Ground, brushed and polished finishes (1G, 2G, 2J, 2K) can be agreed. Specify the route code on the order because it fixes surface condition and the tolerance standard that applies.

Dimensions, tolerances and flatness

Tolerances depend on the product form: EN 10029 for quarto plate (thickness classes A, B, C, D and flatness classes N and S), EN 10051 for hot-rolled wide strip and sheet cut from it, and EN ISO 9445-1/-2 for cold-rolled material. State the tolerance class on the order; class B (all minus tolerance removed) is common for pressure and structural plate.

European ordering practice. An EN order gives the product form (C, H or P), the steel name or number, the process route code, the dimensions and the EN tolerance standard, and the inspection document type. Under the Pressure Equipment Directive, plate for pressure parts is normally ordered to EN 10028-7 or with a particular material appraisal, and the certificate is a 3.1 from a mill with an approved quality system or a 3.2 with third-party witness. Corrosion testing to EN ISO 3651-2 is applied only when ordered. Many buyers also add AD 2000 W2 or project-specific requirements, which should be quoted in full.

1.4652 X1CrNiMoCuN24-22-8 plate stock in China

Thickness (mm) Width (mm) Length (mm) Finish Approx. quantity Location
6 1500 / 2000 6000 1D 100+ t China
8 1500 / 2000 6000 1D 100+ t China
10 2000 6000 1D 100+ t China
12 2000 6000 1D 100+ t China
16 2000 / 2500 6000 1D 100+ t China
20 2000 / 2500 6000 / 8000 1D 100+ t China
30 2000 / 2500 6000 1D 100+ t China

Quantities are approximate and stock changes daily. Send your size list for current availability; other thicknesses, widths and cut sizes can be supplied from mill production.

Packing and logistics. Plate is bundled on steel or wooden skids with steel bands and edge protection, typically 3–8 t per bundle, and marked with heat and plate numbers. Cut pieces are crated. Heavy and wide plate ships in open-top or flat-rack containers or by break-bulk; we send loading photos with the shipping documents.

1.4652 X1CrNiMoCuN24-22-8 equivalents in other standards

Standard Designation Comment
ASTM / UNS UNS S32654 same alloy family and limits closely matched; compare each limit on the certificate
GB/T 015Cr24Ni22Mo8Mn3CuN (S32652) same alloy family and limits closely matched; compare each limit on the certificate

Equivalents are close, not identical. When a project names one standard, order to that standard or ask for multiple certification and check every limit on the certificate.

Related grades by alloy family

Super austenitic

6Mo and 7Mo grades for seawater and chloride service; upgrade path from 316L and 904L: A240 N08904, A240 S31726, 1.4547 plate, 1.4529 plate, 1.4539 plate.

Super duplex

PREN 40+ duplex grades for seawater and severe chlorides: A240 S32750, 1.4410 plate, 1.4501 plate, 1.4507 plate.

Austenitic

General-purpose austenitic grades for comparison: A240 S30400.

Same standard

Other grades in this standard: 1.4162 plate, 1.4565 plate, 1.4662 plate.

Applications, forming and welding of 1.4652 X1CrNiMoCuN24-22-8

Typical uses: plate heat exchangers, seawater cooling systems, bleach plants, FGD equipment and chemical vessels.

In fabrication, plate cuts and forms like heavy austenitic plate but needs higher bending forces because of the nitrogen. Cut by plasma, laser or waterjet and remove heat tint by pickling or grinding. For welding use an over-alloyed nickel-base filler such as ERNiCrMo-3 or ERNiCrMo-13 (AWS A5.14), because a matching filler would lose molybdenum to segregation in the weld. Keep the weld area clean and free of carbon-steel contamination, and pickle and passivate after welding where corrosion resistance matters.

Welding practice. Weld with low to moderate heat input and interpass temperature below about 100 °C. An over-alloyed nickel-base filler compensates for molybdenum segregation in the weld metal; autogenous welds lose much of the base-metal pitting resistance and should be avoided on wetted surfaces unless the weld is solution annealed afterwards. Pickling after welding is essential to restore the passive layer.

Certificates, testing and receiving inspection

Every delivery carries a mill certificate to EN 10088-1 and EN 10088-2 with heat analysis, tensile results and hardness, and the grade and standard as ordered. Supplementary tests we can arrange: ASTM G48 Method A or critical pitting temperature (Method C/E), ASTM A262 practice where specified, microstructure check for sigma/chi, ultrasonic testing of plate, and PMI. Third-party witness by SGS, BV, TÜV, DNV, ABS or LR is available with EN 10204 3.2 certificates.

On receipt, check marking and heat number against the certificate, measure thickness at several points and confirm the finish and edge condition before cutting.

Common mistakes when specifying 1.4652 X1CrNiMoCuN24-22-8

  • Ordering by trade name instead of the UNS or EN number, which leaves chemistry open.
  • Welding with matching filler on seawater-wetted surfaces.
  • Skipping a corrosion acceptance test on heavy plate where segregation is most likely.

Each of these can be avoided by writing the requirement into the purchase order and checking it on the certificate before the material is cut.

Sourcing 1.4652 X1CrNiMoCuN24-22-8: buyer concerns and SHH STEEL solutions

Concern How SHH STEEL handles it
Segregation and sigma in thick plate solution-anneal temperature and quench recorded; G48 or CPT test on the actual heat
Long mill lead times stock plate checked first; heats reserved early for project quantities
Small quantities across many sizes mixed thicknesses and grades combined in one shipment
Cutting and edge preparation in-house shearing, plasma, laser and waterjet cutting, bevelling
Delivery delays weekly production and shipping updates with photos

How to order 1.4652 X1CrNiMoCuN24-22-8 plate

State the standard and edition (EN 10088-2), the grade (1.4652 X1CrNiMoCuN24-22-8), thickness, width and length or coil, finish, quantity, tolerance class, any added chemistry limits, the supplementary tests and acceptance values from your specification, the certificate type and inspection agency, and packing. Send the list to SHH STEEL and we will reply with price, available stock and lead time.

FAQ

Is 1.4652 plate covered by EN 10088-2 or EN 10028-7?
EN 10088-2 covers general-purpose plate. For pressure equipment under the PED, order to EN 10028-7 where the grade is listed there, because it adds elevated-temperature proof-strength values.
Is 1.4652 X1CrNiMoCuN24-22-8 equivalent to UNS S32654?
They are the same alloy designation in different standards. Limits are closely matched, but always order to the standard named in your specification or ask for multiple certification.
Is 1.4652 X1CrNiMoCuN24-22-8 better than super duplex in seawater?
Both are used in seawater. Super-austenitic grades are fully austenitic, tough at low temperature and not limited to about 300 °C, while super duplex has higher strength. The choice depends on temperature, chlorination and design stress.
Can I order small quantities or cut sizes?
Yes. We combine mixed thicknesses and grades into one shipment and cut plate and sheet to size in our workshop.
Which certificates and tests can you provide?
Every order ships with a mill certificate (EN 10204 3.1 type) showing heat analysis and mechanical tests. Supplementary tests and 3.2 certificates with SGS, BV, TÜV or another agency are available by agreement.

Conclusion

1.4652 X1CrNiMoCuN24-22-8 plate should be ordered with the points the standard leaves open written into the contract: finish, tolerance class, any extra chemistry limits and the supplementary tests your application needs. With those fixed, stock material from China is a fast and reliable route.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X