Q390NE Steel Plate GB/T 1591 Supplier

Q390NE, also searched as GB/T 1591 Q390NE, Q390NE steel plate, Q390NE plate and Q390 NE, is the 390 MPa quality-grade-E grade delivered normalized or normalizing-rolled in GB/T 1591-2018. Q is the yield symbol, 390 is the thin-plate minimum yield in MPa, N is the delivery letter, and E is the quality letter for Charpy impact at −40°C.

The N is the point of this page. Hot-rolled Q390E has no N. Thermomechanical Q390ME has an M. A hot-rolled certificate cannot be stamped NE. A TMCP certificate cannot be stamped NE. Grade B is +20°C and is GB/T 1591 Q390NB. Grade C is 0°C and is GB/T 1591 Q390NC. Grade D is −20°C and is GB/T 1591 Q390ND. Q390 sits between GB/T 1591 Q355NE and GB/T 1591 Q420E. Do not drop a 390 MPa drawing onto a 355 MPa plate, and do not upgrade it to 420 MPa without a price check.

EN 10025 has no S390 letter. The closest higher comparison is EN 10025-3 S420NL, a normalized fine-grain grade tested colder than −20°C. EN 10025-3 S420N is −20°C and is the warmer comparison. EN 10025-3 S355NL is the lower normalized comparison. On the US side, ASTM A572 Gr.55 is 55 ksi / 380 MPa, one step lower, and it is not an NE twin. JIS G3106 SM520B is the usual Japanese comparison. Dual mark only when both books are fully met. See EN 10025-3 and high strength low alloy plates.

SHH STEEL is a global steel mill sourcing partner and steel manufacturer and exporter, mill-direct, China origin. We source Q390NE from first-line structural mills, print heat analysis and product analysis when ordered, and ship plate to fabricators in the United States, Europe, the Middle East, Southeast Asia, Africa and South America. Related pages include structural steel plates and the products index.

Nearby pages that buyers compare, but must not swap blindly, include EN 10025-3 S420NL, ASTM A572 Gr.55 and GB/T 1591 Q355NE.

Heat analysis is the mill ladle table in GB/T 1591-2018 for normalized Q390. Product analysis, when ordered, follows GB/T 222. Q390NE is a microalloyed HSLA plate. Grade E is the tightest cleanliness letter on normalized Q390, because the impact test is at −40°C. Mills may add Nb, V or Ti. The certificate shows the elements actually used.

Heat Analysis and Product Analysis — GB/T 1591 Q390NE, normalized

Carbon equivalent is limited by thickness in the standard. The N route often has a different CEV window from hot-rolled Q390E. If the purchase order writes product analysis, SHH STEEL prints both columns and the thickness band used for the tensile test. Do not treat this chemistry as quenched-and-tempered GB/T 16270 Q460E. A 355 MPa file is GB/T 1591 Q355E, not this grade.

Buyers search Q390NE mechanical properties, Q390NE yield strength, GB/T 1591 Q390NE tensile and Q390NE impact −40°C.

Tensile and impact — GB/T 1591 Q390NE, normalized

Impact energy is the average of three longitudinal Charpy V-notch specimens, commonly 27 J to 34 J minimum at −40°C, depending on the ordered edition and thickness. One value may fall below the table, but not below 70% of that value. Write a higher energy on the order if the owner requires it. Not every normalized heat will hold E on very thick plate. SHH STEEL confirms the thickness before promising the letter.

Yield steps down with thickness. A 390 MPa name on 12 mm plate is not the minimum on a 40 mm flange. 390 MPa is about 56.5 ksi. ASTM A572 Gr.55 is 55 ksi and is not this book. Density is 7.85 g/cm³. Hardness is not a design value for this grade. Z15, Z25 or Z35 through-thickness tensile is an extra, not part of the E letter.

A warmer 420 MPa file is GB/T 1591 Q420B. A 460 MPa file is GB/T 1591 Q460E.

There is no official one-to-one substitute for Q390NE. What buyers compare is a 390 MPa normalized plate tested at −40°C.

EN 10025 has no S390. EN 10025-3 S355NL is lower and tested colder. EN 10025-3 S420NL is higher. EN 10025-3 S420N is only −20°C. EN 10025-2 S355J2 is −20°C and only 355 MPa. In the United States, ASTM A572 Gr.55 is 55 ksi / 380 MPa. ASTM A572 Gr.50 is 50 ksi and is one step lower. ASTM A36 is 36 ksi and is well below this yield. In Japan, JIS G3106 SM520B is the usual comparison. SHH STEEL will not stamp EN 10025-3 S420NL or ASTM A572 Gr.55 on a Q390NE certificate unless the purchase order names both books and both tables are met.

Buyers pick Q390NE when a bridge, building member or welded fabrication wants about 390 MPa yield, a normalized or normalizing-rolled condition, and impact at −40°C. Search phrases such as Q390NE steel plate and GB/T 1591 Q390NE all point here.

It is the wrong plate when the drawing says hot rolled only. That work is Q390E. It is the wrong plate when the drawing says TMCP. That work is Q390ME. It is the wrong plate for a −20°C file. That work is GB/T 1591 Q390ND. It is the wrong plate for a +20°C file. That work is GB/T 1591 Q390NB. It is the wrong plate for a 420 MPa file. That work is GB/T 1591 Q420E or GB/T 1591 Q420D. It is the wrong plate for a 460 MPa file. That work is GB/T 1591 Q460C or GB/T 1591 Q460D. It is the wrong plate for a pressure vessel. That work sits on ASTM A516 or pressure vessel steel plates.

SHH STEEL supplies this plate when the drawing names GB/T 1591, quality grade E, and the N condition at 390 MPa.

Q390NE is a weldable normalized HSLA structural plate. Carbon is controlled, and many heats use Nb, V or Ti. A procedure written for ASTM A36 is not a finished WPS for thick Q390NE. Carbon equivalent on the N route is not the same window as hot-rolled Q390E. A procedure qualified only at −20°C may miss the −40°C coupon.

Typical consumables are matching 55–60 ksi low-hydrogen electrodes or wires. E7018-class electrodes are under-matched if the joint must develop full plate strength. A procedure written for ASTM A572 Gr.55 is a useful strength reference after chemistry and the −40°C coupon are checked. Preheat follows thickness, hydrogen and the approved WPS. Thick plate and restrained joints need more preheat than a 10 mm web.

The fabricator owns the WPS. SHH STEEL can share mill heat data, product analysis and carbon equivalent for that review. Do not use a Q390NE procedure on Q390ME without checking the TMCP carbon equivalent.

Usual delivery from SHH STEEL for Q390NE is normalized or normalizing rolled. The plate is not hot rolled as Q390E and not thermomechanical rolled as Q390ME.

Normalizing is typically about 880–920°C, followed by air cooling, unless the mill uses a normalizing-rolling route that the standard accepts for the N letter. Do not order Q390NE as quenched and tempered. That route belongs to GB/T 16270. Stress relief after fabrication, if used, should be agreed before cutting.

The certificate lists GB/T 1591 Q390NE, heat number, delivery condition, heat analysis, product analysis when ordered, tensile by thickness band, and −40°C impact. Certificates may be EN 10204 3.1 or EN 10204 3.2. Dual marking to EN 10025-3 S420NL is available only when both books are fully met.

Usual supply range from SHH STEEL for Q390NE steel plate:

• Thickness: commonly 8 mm – 60 mm, heavier plate to 80 mm by mill confirmation
• Width: 1500 mm – 2800 mm, wider by enquiry
• Length: 3000 mm – 12000 mm

Cut-to-size webs, flanges, base plates and gussets are available. Browse more sizes on structural steel plates.

Dimensional limits for Q390NE follow GB/T 709 unless the purchase order names EN 10029 or another table.

Typical thickness tolerance idea for Q390NE plate

Width on 1500–2800 mm plate is commonly held to about +20 / 0 mm or ±25 mm unless a tighter extra is named. Length on 3000–12000 mm plate is commonly held to about +50 / 0 mm. Flatness follows the agreed class. SHH STEEL will not assume a zero-minus extra on Q390NE unless the order says so.

Q390NE already defines 390 MPa yield, normalized delivery and −40°C impact. Extra items still have to be written on the purchase order.

Book name. Write GB/T 1591 Q390NE. Do not write only Q390, and do not write Q390E if the mill must stamp N.

Impact. Grade E is −40°C. Write a higher energy if the owner requires it.

Delivery condition. Write normalized or normalizing rolled. Write Q390E if hot rolled is enough. Write Q390ME if TMCP is required.

EN or US comparison. Write EN 10025-3 S420NL or ASTM A572 Gr.55 only if dual mark is required and both tables are met. Do not treat EN 10025-3 S420N as a −40°C grade.

Product analysis. Write it if the file needs the second chemistry column.

Through-thickness. Z15, Z25 or Z35 when the joint is loaded through the thickness.

NDE. UT to GB/T 2970 or the named class.

Identification. Heat number, Q390NE, thickness and mill logo.

Third-party witness. EN 10204 3.2 with SGS, TÜV, BV, ABS or the inspector named.

Q390NE is the plate for a 390 MPa normalized file tested at −40°C. It is the wrong plate for a painted weathering facade that needs corten. It is the wrong plate for a 690 MPa QT boom under GB/T 16270.

SHH STEEL sources Q390NE from first-line Chinese structural mills and ships it on worldwide terms. Partner mills include Wuyang (Wugang), Angang, Shougang, Hanye, Anyang Iron and Steel, Baosteel, Xinyu, Xingcheng and other qualified mills when the size requires it.

Mill test certificates are issued to EN 10204 3.1 as standard. EN 10204 3.2 is arranged when the order names a third-party hold point.

Usual rolling thickness: 8 mm, 10 mm, 12 mm, 16 mm, 20 mm, 25 mm, 30 mm, 40 mm, 50 mm, 60 mm. Heavier plate is confirmed before order.

Processing: CNC or flame cutting, bevel, flattening, shot blast, UT to the named class.

Trade terms: FOB Shanghai main, CIF destination available. Payment: TT, LC, or TT + LC.

Ocean time from Shanghai: US West 14–18 days; US Gulf 28–35 days; Rotterdam / Antwerp 28–35 days; Jebel Ali 18–25 days; Singapore 7–12 days; other ports quoted.

Third-party: SGS, TÜV, BV, ABS, CCS, GL, VL, DNV, RINA, NK, KR, or the inspector named.

SHH STEEL is a global steel mill sourcing partner with mill partnerships in China. We supply GB, ASTM, ASME, EN, DIN and JIS steel to buyers in the United States, Europe, the Middle East, Southeast Asia, Africa and South America. Origin is mill-direct, China origin.

SHH STEEL has supplied steel plates to the USA, Mexico, Argentina, Peru, El Salvador, Spain, Netherlands, Germany, UAE, Saudi Arabia, South Africa, India, Thailand, Singapore, Vietnam, the Philippines, Japan and Korea.

Typical lead time: ex-stock 5–7 days when an E heat is in yard; standard normalizing with −40°C test about 30–45 days; 3.2 inspection about 40–50 days.

SHH STEEL is a global steel mill sourcing partner and steel manufacturer and exporter, mill-direct, China origin. For Q390NE that means mill-direct structural price, not a multi-layer stockist mark-up. We buy from mills that can actually normalize the heat and test at −40°C, so the N and the E are both on the certificate.

Delivery is short when the size is in rolling range: ex-stock 5–7 days, standard NE heat about 30–45 days, 3.2 inspection about 40–50 days. Cutting, bevel and UT can run in the same window. FOB Shanghai is the main term. CIF to US West, US Gulf, Rotterdam, Jebel Ali and Singapore is quoted on the same file.

Experience on this grade is simple: print GB/T 1591 Q390NE, keep the normalized route, and do not ship Q390E or Q390ME as NE. We will not drop the N to save a furnace cycle, and we will not change E to D to save a cold test. If the drawing only needs hot-rolled plate, we will move the inquiry to Q390E and keep the price on the right condition.

Q390NE steel plate to GB/T 1591 is 390 MPa normalized structural plate with impact at −40°C. It is not hot-rolled Q390E and not TMCP Q390ME. EN 10025 has no S390. ASTM A572 Grade 55 is 380 MPa and is not a substitute. Whether the inquiry says Q390NE, GB/T 1591 Q390NE or Q390NE steel plate, SHH STEEL as a global steel mill sourcing partner supplies plate with Q390NE chemistry, heat and product analysis as ordered, GB/T 709 tolerances and EN 10204 3.1 or 3.2 certification.

SHH STEEL supplies Q390NE Steel Plate to the United States, Europe, the Middle East, Africa, Asia and the Americas for work that actually names the N condition.

Contact SHH STEEL for mill rolling, −40°C impact, cutting, UT, 3.2 inspection or a worldwide quotation.

Q390NE, Q390NE steel plate, GB/T 1591 Q390NE, Q390NE plate, Q390NE supplier, SHH STEE