JIS G4304 SUS445J2 Hot Rolled Stainless Steel Plate at SHH STEEL warehouse

JIS G4304 SUS445J2 Hot Rolled Stainless Steel Plate

JIS G4304 SUS445J2 hot rolled stainless steel plate: ferritic grade to JIS G 4304:2021, No.1 finish, standard thicknesses from 2.0 mm, cut to size. SHH STEEL supplies mill-direct plate with third-party inspection, small-order consolidation and in-house cutting, bevelling and machining.
Keywords
JIS G4304 SUS445J2 plate, SUS445J2 hot rolled stainless steel plate, SUS445J2-HP plate, JIS SUS445J2 stainless plate, SUS445J2 No.1 plate, SUS445J2 plate supplier
Equivalent Grades:
GB/T 019Cr23Mo2Ti (S12361)
Share:
Overview
Specification
Chemical Composition
Mechanical Properties
Heat Treatment
Tolerances
Surface Finish and Weight
Supply Range
Properties in Service
Equivalent Grades
Related Grades
Applications
Fabrication
Testing and Inspection
Buyer Concerns
How to Order
FAQ
Conclusion

What is JIS G4304 SUS445J2 hot rolled stainless steel plate?

JIS G4304 SUS445J2 hot rolled stainless steel plate is a JIS-specific 22Cr-2Mo ferritic grade with very low C and N, more highly alloyed than SUS445J1. It is one of the 66 grades in JIS G 4304:2021, the Japanese Industrial Standard for hot-rolled stainless steel plate, sheet and strip, where it belongs to the ferritic group listed in Table 5. Under the standard, plate and strip are hot rolled, heat treated, then pickled or given an equivalent descaling treatment, which produces the No.1 finish, and the standard thickness range for plate starts at 2.0 mm and runs into heavy gauges, with thickness tolerances tabulated up to 200 mm. In the annealed condition JIS G4304 requires a minimum 0.2 % proof stress of 245 N/mm² (applied when the purchaser specifies it) and a minimum tensile strength of 410 N/mm². Its closest international counterparts are GB/T 019Cr23Mo2Ti (S12361). Buyers use SUS445J2 plate for roofing and wall panels in coastal areas, water equipment and chemical parts. Because the grade is ordered by its JIS symbol, the order must state JIS G4304, the grade, the dimensions and tolerance class, the finish and any supplementary tests such as product analysis or intergranular corrosion testing, which are applied only when the purchaser asks for them. This page sets out those requirements from the standard in the order a buyer needs them: specification, heat and product analysis, mechanical properties, heat treatment, tolerances, equivalents, applications, fabrication and inspection.

SHH STEEL supplies JIS G4304 SUS445J2 plate mill-direct, with mill test certificates to JIS G 0415 and optional third-party witness. We can cut plate to size, bevel edges and machine parts in our own workshop before shipment.

Values on this page are taken from JIS G 4304:2021 and JIS G 0321:2017. Where the standard leaves a point to agreement, or where a cross-reference is not exact, the page says so instead of giving a figure. Data note: SUS445J2 has no recognised EN or ASTM/UNS equivalent.

JIS G4304 SUS445J2 plate: specification summary

JIS G4304 covers hot-rolled stainless steel plate and strip in one standard. Plate means cut lengths and strip means coil; the cold-rolled counterpart is JIS G4305, so SUS445J2 plate thinner than the hot-rolled range, or with a cold-rolled 2B or BA finish, is ordered to JIS G4305 instead. The summary below collects the clauses that matter for a SUS445J2 plate order.

Item JIS G4304 requirement for SUS445J2
Standard JIS G 4304:2021, Hot-rolled stainless steel plate, sheet and strip
Grade symbol SUS445J2 (add “-HP” for plate or “-HS” for strip when the product form must be shown, e.g. SUS445J2-HP)
Classification Ferritic (Table 5 chemistry)
Corresponding ISO standards ISO 16143-1:2014, ISO 9444-1:2009, ISO 9444-2:2009 and ISO 18286:2008 (all MOD)
Manufacturing route Hot rolled, heat treated, pickled or equivalent descaling; straightening, grinding or skin-pass rolling allowed (clause 4)
Heat treatment Annealed unless otherwise specified. Heat treatment may be omitted by agreement, marked “AR”.
Surface finish No.1 (hot rolled, heat treated and pickled); polished finishes such as No.3, No.4, #240, #320 and #400 by manufacturer’s practice
Standard plate thicknesses 2.0, 2.5, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 12.0, 15.0, 20.0, 25.0, 30.0, 35.0 mm (Table 16); others by agreement
Standard plate sizes 1 000 × 2 000, 1 219 × 2 438, 1 219 × 3 048, 1 524 × 3 048 mm (Table 16)
Thickness tolerance Class A (±) Table 20 by default; class B (Table 21) or class C (Table 22) when specified; tabulated from 2.00 to 200 mm
Flatness Table 29 when the purchaser requires it; stricter class EF may be specified
Product analysis On request, heat-analysis limits widened by JIS G 0321 Table 5 tolerances (clause 5.2)
Tests Heat analysis; tensile test (JIS Z 2241) and hardness (JIS Z 2243-1, Z 2244-1 or Z 2245); 180° bend test (JIS Z 2248)
Corrosion test Intergranular corrosion test only when specified (JIS G 0571/0572/0573/0575)
Inspection document JIS G 0415 type 3.1 unless otherwise specified (clause 14); 3.2 with third-party witness on request
Standard mass (density) 7.73 kg/(mm·m²) for plate mass calculation (Table 19)

SUS445J2 plate chemistry: heat analysis vs product analysis

JIS G4304 sets the heat (ladle) analysis of SUS445J2 in Table 5. When the purchaser asks for a product (check) analysis on the finished plate, clause 5.2 applies the permitted variations of JIS G 0321 Table 5 for stainless and heat-resisting steels. Under JIS G 0321 the variation is chosen from the band that contains the specified maximum, or the specified minimum when only a minimum is given, and the product analysis may lie outside the heat-analysis range only by that amount. The table compares the two, in mass %.

Element Heat analysis (JIS G4304) JIS G 0321 variation Product analysis (permitted)
C ≤ 0.025 +0.005 ≤ 0.030
Si ≤ 1.00 +0.05 ≤ 1.05
Mn ≤ 1.00 +0.030 ≤ 1.03
P ≤ 0.040 +0.005 ≤ 0.045
S ≤ 0.030 +0.005 ≤ 0.035
Cr 21.00–24.00 −0.25 / +0.25 20.75–24.25
Mo 1.50–2.50 −0.10 / +0.10 1.40–2.60
N ≤ 0.025 +0.010 ≤ 0.035

Notes: Ni must not exceed 0.60 % (Table 5, note a). If Cu, V, Ti or Nb are added, their content must be reported (Table 5, note c). Elements not listed are not specified. JIS G 0321 Table 5 does not cover every element or combination; for those the product-analysis tolerance is agreed between purchaser and manufacturer (JIS G4304 5.2).

For comparison, the pitting resistance equivalent number calculated with PREN = Cr + 3.3 Mo + 16 N from the heat-analysis limits is about 25.9 at the minimum and 32.6 at the maximum of the ranges. JIS G4304 does not specify PREN; it is a ranking tool only, and a guaranteed minimum PREN must be agreed as a supplementary requirement.

A single heat analysis on the mill certificate is the acceptance basis under JIS G4304. If PMI or check analysis is required on receipt, the purchaser should say so in the order and refer to the product-analysis limits above; SHH STEEL can arrange PMI and laboratory chemistry through partner laboratories.

Mechanical properties of JIS G4304 SUS445J2 plate

Mechanical properties of SUS445J2 plate are verified on one sample per heat and heat-treatment lot (clause 11.2), using JIS Z 2241 tensile test pieces No. 4, No. 10 or No. 13B (or No. 14A, 14B or 5) at 23 ± 5 °C. The proof stress applies when the purchaser specifies it; tensile strength, elongation and hardness always apply. Any one of the hardness scales may be used, at the manufacturer’s choice unless specified.

Property Requirement (Table 11, annealed)
0.2 % proof stress ≥ 245 N/mm²
Tensile strength ≥ 410 N/mm²
Elongation ≥ 20 %
Hardness ≤ 217 HBW, or ≤ 96 HRBW/HRBS, or ≤ 230 HV
Bend test 180°, inner radius 1.0 × thickness, no cracks on the outside

1 N/mm² = 1 MPa. JIS G4304 does not specify elevated-temperature or impact properties for SUS445J2; where a design code needs them, they must be added to the order. The standard also does not specify properties after any heat treatment done by the buyer after delivery.

Heat treatment of SUS445J2 plate

JIS G4304 Annex JA (informative) gives the following example heat-treatment condition for SUS445J2: Annealing 850–1 050 °C, rapid cooling. Because Annex JA is informative, the mill chooses the actual temperatures within its own practice, and the certificate records the heat-treatment condition.

Ferritic plate is annealed unless otherwise specified. Heat treatment may also be omitted by agreement, in which case the plate is marked “AR” (as rolled) and the mechanical-property requirements are agreed between the parties.

Thickness, width, length and flatness tolerances for SUS445J2 plate

Clause 9.3 gives the dimensional and shape tolerances for SUS445J2 plate. The default thickness tolerance is class A in Table 20 below (mm, by width in mm). The purchaser may instead specify class B (Table 21: plus-only tolerances with −0.25 mm on the minus side) or class C (Table 22: plus-only tolerances with 0 mm on the minus side), which are used when a minimum thickness must be guaranteed. Thickness is measured at least 15 mm in from a cut edge, or 25 mm from a mill edge on plate cut from strip.

Thickness w < 1 000 1 000–<1 250 1 250–<1 600 1 600–<2 000 2 000–<2 500 2 500–<3 150 3 150–4 000
2.00–<2.50 ±0.25 ±0.30 — — — — —
2.50–<3.15 ±0.30 ±0.35 ±0.40 — — — —
3.15–<4.00 ±0.35 ±0.40 ±0.45 — — — —
4.00–<5.00 ±0.40 ±0.45 ±0.50 ±0.60 ±0.80 ±1.0 —
5.00–<6.00 ±0.50 ±0.55 ±0.60 ±0.70 ±0.90 ±1.1 —
6.00–<8.00 ±0.60 ±0.65 ±0.65 ±0.75 ±1.0 ±1.2 ±1.4
8.00–<10.0 ±0.65 ±0.65 ±0.65 ±0.80 ±1.2 ±1.5 ±1.6
10.0–<16.0 ±0.70 ±0.70 ±0.70 ±0.85 ±1.2 ±1.5 ±1.6
16.0–<25.0 ±0.80 ±0.80 ±0.80 ±0.95 ±1.3 ±1.5 ±1.6
25.0–<40.0 ±0.90 ±0.90 ±0.90 ±1.1 ±1.3 ±1.5 ±1.6
40.0–<63.0 ±1.0 ±1.0 ±1.2 ±1.2 ±1.4 ±1.5 ±1.6
63.0–<100 ±1.1 ±1.2 ±1.3 ±1.3 ±1.5 ±1.6 ±1.7
100–<160 ±1.3 ±1.3 ±1.4 ±1.4 ±1.6 ±1.7 ±1.8
160–200 ±1.6 ±1.6 ±1.7 ±1.7 ±1.9 ±2.0 ±2.1

Width and length tolerances depend on the cutting method. For plate cut by mechanical, plasma, laser or waterjet cutting under 10.0 mm thick, Table 25 gives +10/0 mm on width for lengths up to 3 500 mm and widths under 2 000 mm, increasing with length and width; flame (powder) cut plate has wider tolerances, for example +30/+5 mm. Length tolerances in Table 27 follow the same pattern. As-rolled plate (mill edge) has width and length tolerances specified on the plus side only.

Flatness is measured only when the purchaser requires it (Table 29), as the maximum deviation over any 3 500 mm length. For plate up to 1 000 mm wide and up to 2 000 mm long the limit is 15 mm, or 3 mm for the stricter class EF; for widths over 1 000 and up to 1 600 mm it is 20 mm, or 6 mm for EF. Wider plate has limits from 25 to 50 mm and no EF class. Buyers who need flat plate for machining or laser cutting should specify EF, or ask for leveling, at the enquiry stage.

SUS445J2 plate surface finish and weight calculation

The standard surface finish for JIS G4304 plate is No.1: hot rolled, heat treated, then pickled or given an equivalent treatment. It has a dull, slightly rough appearance and is the normal finish for SUS445J2 plate in tanks, structures and process equipment. Polished finishes such as No.3, No.4, #240, #320 and #400, and any other finish not in Table 15, follow the manufacturer’s practice and should be defined in the order, including which side is polished and whether protective film is required.

When the purchaser asks for calculated mass, clause 9.2 and Table 18 apply. The basic mass for SUS445J2 is 7.73 kg/(mm·m²). The unit mass is basic mass × thickness, rounded to four significant figures; the area is rounded to four significant figures; and the plate mass is rounded to three significant figures (or to whole kilograms above 1 000 kg). For class B and C tolerances, Tables 23 and 24 add an allowance to the nominal thickness before calculation. For example, one SUS445J2 plate of 10.0 × 1 219 × 2 438 mm has a unit mass of 7.73 × 10.0 = 77.3 kg/m², an area of 1.219 × 2.438 = 2.972 m², and a calculated mass of 77.3 × 2.972 ≈ 230 kg, rounded as Table 18 requires.

SUS445J2 plate supply forms, sizes and packing

JIS G4304 plate is produced in two ways. Thinner plate, from about 2 mm up to roughly 12 mm in many mills, is cut from continuously hot-rolled, annealed and pickled coil (No.1 coil), and is supplied either as cut-to-length plate or as coil. Thicker plate is usually rolled as discrete plates on a plate (quarto) mill, then heat treated and pickled. The route affects the edge condition (mill edge or cut edge), the available widths and lengths, and the flatness that can be achieved, so the enquiry should state which tolerances and edges are acceptable.

For SUS445J2, the realistic supply range depends on how widely the grade is produced. Ferritic grades are produced mainly as hot-rolled coil and thinner plate; heavy ferritic plate is less common because of toughness limits in thick sections. Standard sizes of 1 219 × 2 438 mm and 1 524 × 3 048 mm are the most widely available; wider plate up to about 2 000 mm and longer lengths can be rolled to order, and any size can be cut from larger plate in our workshop.

Packing for export normally means plates stacked on wooden or steel pallets with interleaving where needed, steel strapping, edge protection and waterproof wrapping, and coils packed eye-to-wall or eye-to-sky. Each bundle carries a label with the grade symbol, size, heat number and bundle weight, which matches the marking required by clause 13 and the inspection certificate.

How SUS445J2 plate performs in service

SUS445J2 is a ferritic stainless steel with a body-centred cubic structure. It is magnetic, contains little or no nickel, and is not hardenable by heat treatment. Ferritic grades are practically immune to chloride stress-corrosion cracking, which is an advantage over 304 and 316 in hot-water and chloride service.

Ferritic grades have lower thermal expansion and higher thermal conductivity than austenitic grades, so they distort less when heated. Their main limitations are lower toughness in thick sections and at low temperature, and grain growth in the heat-affected zone of welds. For these reasons ferritic plate is used mostly in thinner gauges, and heavy ferritic plate is less common than heavy austenitic plate.

JIS G4304 requires a 180° bend test for annealed ferritic plate, with no cracks on the outside of the bend. This checks formability of each lot in addition to tensile strength and hardness.

SUS445J2 equivalent grades: EN, ASTM/UNS and GB/T compared

Buyers often need to know whether SUS445J2 plate can replace, or be replaced by, an EN, ASTM or Chinese grade. The table lists the commonly used cross-references in each system. Cross-references are a guide only: the standards differ in chemical limits, mechanical requirements, tolerances and testing, so dual-certified material must meet every limit of both standards on the same heat.

System Equivalent of SUS445J2
JIS (this page) SUS445J2, JIS G4304 (hot rolled) / JIS G4305 (cold rolled)
EN (EN 10088-2 / EN 10095) No recognised equivalent
ASTM / UNS (ASTM A240) No recognised equivalent
GB/T (GB/T 4237 hot-rolled plate) GB/T 4237 019Cr23Mo2Ti (S12361)
ISO ISO 16143-1 is the corresponding international standard for corrosion-resistant flat products; JIS keeps its own designation system

Uncertainty: SUS445J2 has no recognised EN or ASTM/UNS equivalent.

For SUS445J2 the cross-references above are well established. A mill can often certify one heat to JIS G4304 and the equivalent ASTM A240 or EN 10088-2 grade when the chemistry and properties fall inside both sets of limits; this must be requested in the enquiry, not assumed after production.

The same grade made as cold-rolled plate and sheet is covered by JIS G4305; the standard JIS G4305 chemistry for SUS445J2 matches JIS G4304, but mechanical properties, finishes and tolerances are specified separately for cold-rolled material.

Other JIS G4304 grades related to SUS445J2

SUS445J2 sits within the ferritic group of JIS G4304. These related hot-rolled grades are often compared with it when choosing plate:

  • JIS G4304 SUS444 hot rolled plate: a 19Cr-2Mo stabilised ferritic grade with pitting resistance comparable to or above 316 and immunity to chloride stress-corrosion cracking typical of ferritic grades.
  • JIS G4304 SUS445J1 hot rolled plate: a JIS-specific 22Cr-1Mo ferritic grade with very low C and N, for higher corrosion resistance than SUS444 in some environments.
  • JIS G4304 SUS447J1 hot rolled plate: a high-purity 30Cr-2Mo super-ferritic grade with C ≤ 0.010 % and N ≤ 0.015 %, for very high chloride and acid resistance in a ferritic structure.
  • JIS G4304 SUS430 hot rolled plate: the standard 16–18 % chromium ferritic stainless steel: magnetic, nickel-free and economical, with good resistance to mild atmospheres and oxidation.
  • JIS G4304 SUS430LX hot rolled plate: a low-carbon (C ≤ 0.030 %) 16–19 % chromium ferritic grade stabilised with 0.10–1.00 % titanium or niobium for better weldability and formability than SUS430.
  • JIS G4304 SUS405 hot rolled plate: an aluminium-bearing (0.10–0.30 % Al) 13 % chromium ferritic grade; aluminium limits hardening when the steel is welded or cooled quickly from high temperature.

For the most widely stocked plate grades, see ASTM A240 Type 304 plate, AISI 316L plate and ASTM A240 2205 duplex plate. All JIS G4304 grades are grouped in the JIS G4304 plate category.

More plate pages on this site: AISI 304 plate, JIS G4305 cold-rolled plate range.

Applications of JIS G4304 SUS445J2 plate

SUS445J2 plate is chosen for roofing and wall panels in coastal areas, water equipment and chemical parts. Typical uses include:

  • Roofing
  • Wall panels in coastal areas
  • Water equipment
  • Chemical parts

Ferritic plate is selected where nickel-free cost, magnetic response, low thermal expansion or resistance to chloride stress-corrosion cracking matter more than heavy-section toughness.

Cutting, forming and welding SUS445J2 plate

Cutting. SUS445J2 plate is cut by plasma, laser, waterjet or shearing. Ferritic grades shear cleanly because they work-harden less than austenitic grades.

Forming. Ferritic plate bends well in thin gauges; JIS G4304 itself requires a 180° bend test. Thicker plate should be bent with generous radii and, where needed, slightly warmed to avoid cracking at low temperature.

Welding. Weldability depends on the grade: stabilised low-C,N grades weld well, while higher-carbon unstabilised grades such as SUS430 can lose ductility in the heat-affected zone. Low heat input limits grain growth. Filler is chosen to match corrosion resistance, often a stabilised ferritic or an austenitic consumable.

Testing, marking and certificates for SUS445J2 plate

Clause 11 of JIS G4304 sets the test rules. Heat analysis follows JIS G 0404 and JIS G 0320; a product analysis to JIS G 0321 is made when the purchaser requests it. One sample is taken per heat and heat-treatment lot for mechanical testing, and one test piece is used for each test.

  • Tensile test to JIS Z 2241 at 23 ± 5 °C, with a controlled strain rate for non-martensitic grades.
  • Hardness test to JIS Z 2243-1 (Brinell), JIS Z 2244-1 (Vickers) or JIS Z 2245 (Rockwell) at 23 ± 5 °C.
  • Bend test to JIS Z 2248, test piece No. 1 or No. 3.
  • Intergranular corrosion test to JIS G 0571, G 0572, G 0573 or G 0575 only when specified.
  • Inspection of chemistry, properties, finish, dimensions and appearance under clause 12.

Under clause 13 each plate or bundle is marked with the grade symbol, dimensions, any special tolerance or flatness symbols (B, C, EF), the surface finish, the heat-treatment symbol where applicable (AR, LS, Q or the ageing symbol), the manufacturer’s name or mark, and the heat or inspection number. Under clause 14 the inspection document is JIS G 0415 type 3.1 unless another type is ordered. SHH STEEL checks the marking against the certificate before shipment and can arrange 3.2 certification with an independent inspector.

Sourcing SUS445J2 plate: buyer concerns and SHH STEEL solutions

These are the questions buyers of JIS G4304 SUS445J2 plate ask most often, and how we handle each one:

Buyer Concern SHH STEEL Solution
Quality worries: is the plate and certificate genuine? Every lot can be witnessed by TUV, ABS or CCS, and partner testing labs run PMI, chemistry and tensile checks on SUS445J2 plate against JIS G4304. Third-party witness and EN 10204 3.2 certificates available.
Deposit risk on a new supplier TT and LC are accepted, and can be combined (part TT, part LC). On large projects you may sign directly with the mill, with SHH STEEL handling documents and follow-up for a small fee.
Small orders below mill MOQ Small SUS445J2 plate quantities are combined with other customers’ orders of the same grade so they can be produced even below the mill MOQ, with full heat traceability.
Slow delivery Dedicated staff follow up with the mill through rolling, heat treatment, pickling, testing and packing, and report progress at each stage.
Processing needs Our own workshop provides cutting to size, bevelling and machining to drawings as a value-added service, so plates arrive ready for fabrication.

How to order JIS G4304 SUS445J2 plate

A complete order for SUS445J2 plate avoids queries and delays at the mill. Include:

  • Standard and grade: JIS G 4304:2021, SUS445J2 (or SUS445J2-HP)
  • Dimensions: thickness × width × length in mm, and quantity in pieces and tonnes.
  • Thickness tolerance class (A, B or C) and flatness class (standard or EF) if not the default.
  • Heat-treatment condition, surface finish (No.1, or a polished finish with side and film).
  • Supplementary requirements: proof stress, product analysis, intergranular corrosion test, PMI, ultrasonic testing, dual certification.
  • Inspection document: JIS G 0415 3.1 or EN 10204 3.2, inspector, marking and packing.

SHH STEEL reviews the order against JIS G4304 before placing it with the mill, confirms whether dual certification is possible on the heat, and proposes cutting, bevelling or machining where that saves the buyer time. Send your SUS445J2 plate enquiry with sizes and quantity for a quotation, lead time and inspection plan.

FAQ

What is JIS G4304 SUS445J2?
It is SUS445J2 stainless steel made as hot-rolled plate, sheet or strip to JIS G 4304:2021. The plate is hot rolled, heat treated and pickled to a No.1 finish, with chemistry from Table 5 and the mechanical properties of the matching property table.
What is the equivalent of SUS445J2 in ASTM, EN and GB?
The closest equivalents are GB/T 019Cr23Mo2Ti (S12361). Check each limit before substituting one standard for another.
Is SUS445J2 plate magnetic?
Yes. SUS445J2 is ferritic, so it is magnetic in all conditions. A magnet test cannot tell it apart from other ferritic grades; use PMI to confirm the grade.
What is the density or weight of SUS445J2 plate?
The standard mass used for plate weight in JIS G4304 Table 19 is 7.73 kg per mm of thickness per m², which corresponds to a density of 7.73 g/cm³. A 10 mm plate therefore weighs about 77.3 kg/m².
What is the difference between JIS G4304 and JIS G4305 SUS445J2?
JIS G4304 covers hot-rolled plate and strip with a No.1 finish, from 2.0 mm and up into heavy thicknesses. JIS G4305 covers cold-rolled plate, sheet and strip with finishes such as 2D, 2B and BA. The chemistry of SUS445J2 is the same in both, but properties and tolerances are specified separately.
What certificate comes with JIS G4304 SUS445J2 plate?
Unless another type is ordered, the mill supplies an inspection certificate type 3.1 to JIS G 0415, showing heat analysis and test results. SHH STEEL can arrange EN 10204 3.2 certificates with TUV, ABS or CCS witness on request.

Conclusion

JIS G4304 SUS445J2 hot rolled stainless steel plate is defined by its Table 5 chemistry, the property table for its group, and the dimensional tolerances of clause 9. A good order states the grade and edition, the tolerance and flatness class, the finish and any supplementary tests. SHH STEEL supplies SUS445J2 plate mill-direct with third-party inspection, consolidation of small orders and in-house cutting, bevelling and machining.

Contact Us

Quality Steel Needed? Inquire for Offers

Need quality steel for your project? Inquire now to get tailored offers. Our team ensures quick responses, matching your needs with reliable steel solutions. Start your inquiry today.

    *

    *

    *

    *


    Related Products

    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response
    SHH STEEL Get Your Steel Quote—Inquire Now for Quick Response

      *

      *

      *

      *


      X